Texas Instruments

TLV2771CD - 5.1MHz High-Slew-Rate Op Amp | Texas Instruments

MPN: TLV2771CD ✓ Hoạt động
5.5 V Vdss 8-pin SOIC, 3.9 mm nominal body width Package
MOQ: 1 |

TLV2771CD Tóm tắt

The Texas Instruments TLV2771CD is a single operational amplifier with a 5.5 V maximum supply voltage, 5.1 MHz gain-bandwidth product, and 10.5 V/µs high slew rate, housed in an 8-pin SOIC package. It combines rail-to-rail output operation with the bandwidth and slew rate needed for responsive signal conditioning. The TLV2771CD is intended for instrumentation, buffering, filtering, and general-purpose analog signal-chain applications where a compact, high-speed amplifier is required.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. As a voltage-feedback amplifier, it belongs to the broader hierarchy of amplifier ICs, instrumentation amplifiers, analog signal-processing ICs, and semiconductors. Its high gain and negative-feedback operation make it useful for sensor interfaces, waveform conditioning, active filters, and low-level signal amplification where signal integrity and response speed are important.

The principal performance features are the 5.1 MHz gain-bandwidth product, 10.5 V/µs slew rate, and rail-to-rail output. These characteristics allow the amplifier to reproduce fast-moving waveforms with less distortion than lower-bandwidth general-purpose amplifiers. A 5.5 V maximum supply voltage also supports compact systems operating below 6 V, while the single-amplifier configuration avoids the space and power requirements of a dual or quad device when only one signal path is needed.

Technologically, the TLV2771CD combines CMOS-compatible low-power operation with high-speed, high-output-drive characteristics. The 10.5 V/µs slew rate is particularly useful when driving finite-capacitance loads or following sensor and comparator outputs. Rail-to-rail output maximizes usable signal range at the load, although input common-mode range, output-current behavior, input-bias current, noise, and offset specifications should be checked against the exact circuit requirements before finalizing a precision design.

Typical uses include sensor-signal conditioning, buffered data acquisition, active analog filtering, communications-interface support, and industrial control or test equipment. It is particularly suitable when a design needs more bandwidth than a general-purpose micropower amplifier but does not require the very low noise or precision offset of a specialized instrumentation amplifier. One amplifier per package also supports designs with isolated signal paths or low channel counts.

For PCB implementation, use the manufacturer’s recommended SOIC-8 land pattern, place decoupling close to the supply pins, and avoid long return paths beneath sensitive input nodes. Check output swing, load capacitance, and stability requirements against the operating voltage. Because the SOIC package has exposed lead geometry and limited heat-dissipation area, use appropriate copper spreading and temperature-rise analysis when driving sustained heavy loads.

This page combines the TLV2771CD’s core electrical characteristics with focused application guidance, package considerations, drop-in alternatives, and a parameter-by-parameter comparison. These engineering-oriented details help determine whether the amplifier’s 5.1 MHz bandwidth, 10.5 V/µs slew rate, and 5.5 V supply limit align with the target analog signal chain before layout and prototype work begin.

Bộ thay thế dễ dàng lắp đặt cho TLV2771CD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2771CD (cùng hình factor và footprint) — khác nhau ở Package, Shutdown Function, Slew Rate.

Texas Instruments
Package: 8-SOIC
Shutdown Function: Present
Slew Rate: 10.5 V/us
So sánh với TLV2771CD →

TLV2771ID

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 1 circuit · CMOS operational amplifier · 5.5 V · 2.7 V · 5.1 MHz · 10.5 V/us · 1 mA

Liên hệ để biết giá

Xem tài liệu →

TLV2771AID

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same family and 8-pin SOIC footprint; the A variant changes input common-mode capability while retaining a 5.5 V maximum supply

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2771QD

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same TLV2771 electrical family and 8-pin SOIC footprint; Q-grade temperature limits differ from the commercial TLV2771CD

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2772AID

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same 8-pin SOIC footprint and 5.5 V class supply; shutdown capability is added while bandwidth and drive characteristics require circuit-level verification

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2774AIP

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same TLV277x family and 8-pin SOIC footprint; rail-to-rail input behavior and device-specific AC limits differ from TLV2771CD

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2771CD Tỷ lệ tối đa & tính chất điện

Product Type Single operational amplifier
Maximum Supply Voltage 5.5 V
Minimum Supply Voltage 2.7 V
Gain-Bandwidth Product 5.1 MHz
Slew Rate 10.5 V/µs
Output Topology Rail-to-rail output
Number of Circuits 1 circuit
Hộp 8-pin SOIC, 3.9 mm nominal body width
Kiểu lắp đặt Surface mount
Product Classification General-purpose amplifier
Shutdown Function Not specified for TLV2771; family shutdown variants exist

Hướng dẫn cấu hình chân TLV2771CD 8-pin soic, 3.9 mm nominal body width

Cấu hình chân cho TLV2771CD (8-pin soic, 3.9 mm nominal body width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin soic, 3.9 mm nominal body width cho TLV2771CD

Không có dữ liệu chân cụ thể sẵn có cho TLV2771CD.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

TLV2771CD phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Precision Active Filtering, Data Acquisition Buffering, Communications Interface Support, Battery-Powered Portable Equipment, Test and Measurement Buffer.

🏭

Industrial Sensor Signal Conditioning

The TLV2771CD fits industrial sensor interfaces that require faster response than a conventional general-purpose amplifier. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate can preserve the timing and amplitude of rapidly changing sensor signals while operating from a 2.7 V to 5.5 V supply. Place the amplifier between the sensor and an ADC or controller, and confirm that the input common-mode range covers the sensor’s full output range. The rail-to-rail output helps maximize available signal span in low-voltage equipment. Its single-amplifier SOIC-8 package also conserves board area where only one conditioned channel is required.

🔧

Precision Active Filtering

The TLV2771CD is suitable for active filter stages requiring more bandwidth than a micropower amplifier. A 5.1 MHz gain-bandwidth product provides useful closed-loop bandwidth for low- to moderate-order filters, while the 10.5 V/µs slew rate helps maintain low large-signal distortion when processing high-frequency components. The single 2.7 V to 5.5 V supply simplifies portable and embedded analog systems. Component values should be calculated from the required cutoff, gain, and Q, and the amplifier’s exact noise, offset, and stability characteristics should be checked against the filter’s noise and phase requirements.

📟

Data Acquisition Buffering

The TLV2771CD can buffer sensor outputs before multiplexers, sample-and-hold stages, or analog-to-digital converters. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate reduce the risk of excessive settling time when driving the input capacitance of a successive-approximation ADC. Operating from 2.7 V to 5.5 V also supports common embedded acquisition rails. Confirm ADC acquisition time and input capacitance against the amplifier’s output-drive and stability limits. A low-noise decoupling arrangement and a short, protected route from the sensor are important for preserving measurement fidelity.

🌐

Communications Interface Support

The TLV2771CD is appropriate for communications equipment that needs to buffer line-level or differential signals into a downstream converter. Its 10.5 V/µs slew rate supports faster transitions than basic general-purpose amplifiers, while the 5.1 MHz gain-bandwidth product is useful for moderate-bandwidth signal conditioning. The rail-to-rail output can improve useable swing in a 5 V signal chain. For high-speed links, verify that the required data rate, settling time, capacitive loading, common-mode range, and output-current capability meet the communications standard before using this device.

📱

Battery-Powered Portable Equipment

The TLV2771CD can be used in compact battery-powered equipment requiring a rail-to-rail output amplifier with modest supply requirements. Its minimum operating voltage of 2.7 V supports 3.3 V systems, and its 5.5 V maximum provides compatibility with 5 V rails. The single-amplifier configuration avoids the board area of a multi-amplifier package when only one conditioning channel is required. For portable designs, confirm standby-current requirements, output loading, input bias current, and shutdown requirements; if the amplifier must remain active during battery sleep periods, a micropower device may be more appropriate.

🖥️

Test and Measurement Buffer

The TLV2771CD is useful as a general-purpose buffer in compact test and measurement equipment. The 5.1 MHz gain-bandwidth product supports moderate-frequency signal acquisition, while the 10.5 V/µs slew rate produces faster large-signal transitions than low-bandwidth precision amplifiers. Its 8-pin SOIC package simplifies assembly and replacement, and its rail-to-rail output can preserve signal amplitude at low supply voltages. Validate the complete measurement path for source impedance, probe capacitance, input offset, noise, and settling behavior. A shield or guard structure may be needed when the source has high impedance and leakage can bias the measurement.

What are the key specifications of TLV2771CD that engineers should know?
The TLV2771CD is a single, 5.5 V maximum-supply operational amplifier with a 5.1 MHz gain-bandwidth product, 10.5 V/µs slew rate, and rail-to-rail output. Texas Instruments describes it as a high-slew-rate CMOS operational amplifier in an 8-pin SOIC package. These characteristics place it between conventional general-purpose amplifiers and faster signal-chain devices.
What is the operating voltage of TLV2771CD?
The TLV2771CD operates from 2.7 V to 5.5 V. According to the Texas Instruments TLV2771 product information, the device is a 5.5 V single operational amplifier designed for low-voltage analog systems. The 2.7 V minimum makes it suitable for 3.3 V systems, while the 5.5 V maximum supports 5 V nominal rails.
What is the bandwidth and slew rate of TLV2771CD?
The TLV2771CD has a 5.1 MHz gain-bandwidth product and a 10.5 V/µs slew rate. Texas Instruments identifies the amplifier as a 5.1 MHz, high-slew-rate device. The combination supports faster closed-loop response than low-bandwidth general-purpose amplifiers while remaining suitable for compact instrumentation and signal-conditioning circuits.
Where can I download the TLV2771CD datasheet PDF?
The official TLV2771 datasheet and ordering information are available from the Texas Instruments TLV2771 product page at https://www.ti.com/product/TLV2771. The TLV2771CD ordering option is also listed at https://www.ti.com/product/TLV2771/part-details/TLV2771CD. Use those manufacturer links for the authoritative pin description, electrical characteristics, and ordering table.
Where is the TLV2771CD pinout located?
The TLV2771CD pinout is shown in the pin-configuration section of the Texas Instruments TLV2771 datasheet. The component uses an 8-pin SOIC package, but pin names, shutdown behavior, and exposed-package details should be assigned directly from the manufacturer pin-description table rather than inferred from the distributor summary. Follow the standard SOIC-8 land pattern when laying out the PCB.
Is TLV2771CD suitable for sensor signal conditioning?
The TLV2771CD is suitable for many sensor signal-conditioning applications because it combines a 5.1 MHz gain-bandwidth product with a 10.5 V/µs slew rate. Its rail-to-rail output can maximize signal range in low-voltage systems. Confirm the sensor output range, input common-mode limits, offset, noise, and capacitive loading before selecting it for a precision measurement path.
Where to buy TLV2771CD online?
The TLV2771CD can be requested through the Request a Quote form on this page. The form is the appropriate route for current commercial terms, quantity availability, lead time, and order handling. Its exact orderable designation is TLV2771CD in an 8-pin SOIC package, so include that full MPN in the request to avoid ambiguity.
What is the price of TLV2771CD?
Use the Request a Quote form on this page to obtain the current TLV2771CD commercial terms. Pricing can vary with quantity, package quantity, sourcing condition, and market availability, so a current quotation is more reliable than a static catalog figure. Submit the complete TLV2771CD MPN and required production quantity with the request.
What is the lead time for TLV2771CD?
Request the current TLV2771CD lead time through the Request a Quote form on this page. Lead time can change with order quantity, inventory position, and production scheduling, so it should be confirmed for the exact 8-pin SOIC orderable part. The manufacturer’s TLV2771 ordering page is the appropriate reference for the device’s formal ordering options.
Is TLV2771CD in stock?
Current TLV2771CD inventory should be confirmed through the Request a Quote form on this page. Stock can vary by quantity and order configuration even when a distributor listing indicates immediate availability. Include your required quantity, target date, and acceptable packaging format so the quotation can reflect the actual orderable configuration.
TLV2771CD vs TLV2771ID: which is better for industrial use?
The TLV2771ID is the better choice when the design specifically requires the broader temperature grade associated with that ordering option. Both devices belong to the TLV2771 family and use an 8-pin SOIC footprint, but the commercial and industrial temperature grades differ. Check the manufacturer ordering table for the exact grade, marking, and qualification requirements.
When should I choose TLV2771CD over TLV2771ID?
Choose the TLV2771CD when its specified commercial temperature range covers the intended operating environment and no industrial temperature grade is required. Choose TLV2771ID when ambient conditions extend beyond the commercial grade. Because both use the same 8-pin SOIC footprint, the selection should be based on temperature limits, qualification, and availability rather than PCB changes.
Is TLV2771ID a drop-in replacement for TLV2771CD?
The TLV2771ID is a same-package, pin-compatible option for designs whose electrical needs remain unchanged, but it should not be treated as an unconditional replacement. Its temperature grade differs from the TLV2771CD, and operating conditions must be checked against both devices’ specified limits. The shared 8-pin SOIC format eliminates the need for a footprint redesign.
What can replace TLV2771CD in an existing circuit?
The TLV2771ID is the closest same-family 8-pin SOIC replacement candidate for the TLV2771CD because it retains the family architecture and package footprint. A valid replacement must still satisfy the original circuit’s supply voltage, bandwidth, slew rate, common-mode range, offset, noise, output drive, and temperature requirements. Review the manufacturer comparison before approving the substitution.
What is the best Analog Devices equivalent for TLV2771CD?
No specific Analog Devices equivalent can be confirmed as a true drop-in replacement from the available cross-reference information. A valid cross-brand substitution must use the same 8-pin SOIC pinout and remain within the required 2.7 V to 5.5 V supply range while matching the original bandwidth, slew-rate, offset, noise, and common-mode requirements. Use the Request a Quote form for assistance with a qualified source.

Dữ liệu tham khảo kỹ thuật cho TLV2771CD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the TLV2771CD for compact 2.7 V to 5.5 V analog systems that need a single amplifier with a 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate, especially when the signal is faster than a general-purpose amplifier can accommodate. Its 8-pin SOIC package and rail-to-rail output are useful for sensor conditioning, filtering, and moderate-speed acquisition. Choose TLV2771ID when the broader industrial temperature grade is required, TLV2771AID when its input common-mode characteristics better match the source, and TLV2772AID when shutdown capability is valuable. Do not select any replacement solely from package compatibility: verify input range, offset, noise, load drive, stability, and temperature limits against the original circuit. Use the Request a Quote form when current sourcing and lifecycle confirmation are needed.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này TLV2771ID TLV2771AID TLV2771QD TLV2772AID TLV2774AIP
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Maximum Supply Voltage 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V
Minimum Supply Voltage 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V 2.7 V
Output Topology Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output

Bảo phân biệt quan trọng

  • Combines moderate bandwidth with a high slew rate (vsTLV2771AID)
  • Supports low-voltage, high-speed signal conditioning (vsTLV2772AID)
  • Commercial-grade option in a standard SOIC footprint (vsTLV2771ID)

Ghi chú thiết kế

Use the manufacturer’s 8-pin SOIC land pattern and place the input, output, and supply decoupling components close to their associated pins. Keep the ground return short and continuous, avoid routing sensitive input traces beneath the package, and separate analog input routing from clocks, switching-node copper, and other high-energy paths. The rail-to-rail output improves signal range, but it does not remove the need for careful analog grounding.

Do not assume that the 5.1 MHz gain-bandwidth product permits 5.1 MHz operation at every closed-loop gain. The usable bandwidth, phase margin, and output swing depend on the selected gain, noise gain, load capacitance, and supply voltage. Likewise, the 10.5 V/µs slew rate describes the maximum output transition rate rather than guaranteed bandwidth. Use the manufacturer’s stability and load-capacitance guidance before driving ADC inputs, long cables, or large capacitive loads.

Keep the supply within the device’s 2.7 V to 5.5 V operating limits and account for supply noise, startup transients, and input-signal excursions that may approach the rails. Add local bypass capacitance to suppress supply ripple, especially when the amplifier follows a switching converter. For low-power designs, compare the operating current at the selected signal level because a high-speed amplifier may consume more power than a micropower precision device.

For instrumentation applications, verify input offset, input bias current, noise, common-mode range, and output-current capability against the source and load. A high-impedance sensor can require guarding or a bias resistor to control input bias-induced error. If the output drives a sampling ADC, check settling time for the selected closed-loop gain and consider a small isolation resistor when capacitive loading could impair stability.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The TLV2771 is a general-purpose commercial operational amplifier and is not an automotive-qualified AEC-Q100 device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.

Dữ liệu được xác minh vào: 2026-11-15 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

TLV2771CD datasheet TLV2771CD specifications TLV2771CD pinout TLV2771CD datasheet pdf TLV2771CD replacement TLV2771CD equivalent TLV2771CD cross reference TLV2771CD vs TLV2771ID Texas Instruments TLV2771CD TLV2771CD price TLV2771CD stock TLV2771 application circuit 5.1MHz operational amplifier SOIC-8

Các bộ phận và thuật ngữ liên quan

Texas Instruments TLV2771CD TLV2771 TLV2771ID TLV2771AID TLV2771QD TLV2772AID TLV2774AIP operational amplifier single operational amplifier amplifier IC analog signal-processing IC voltage-feedback amplifier rail-to-rail output amplifier CMOS operational amplifier 5.1 MHz gain-bandwidth product 10.5 V/µs slew rate 2.7 V minimum supply voltage 5.5 V maximum supply voltage 8-pin SOIC SOIC package family surface-mount package signal conditioning active filtering data acquisition
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ