TLV2771ID - 5.1 MHz, 10.5 V/us Rail-to-Rail Op Amp | TI
N.º da peça: TLV2771ID ✓ AtivoTLV2771ID Visão geral
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2771 belongs to the CMOS operational-amplifier hierarchy, where low supply voltage, low power consumption, and moderate-to-high bandwidth support portable, industrial, communications, and sensor-interface applications. Its rail-to-rail output lets the output approach the supply rails more closely than a conventional fixed-output amplifier.
Three defining performance characteristics are the 5.1 MHz gain-bandwidth product, 10.5 V/us slew rate, and approximately 1 mA supply current per channel. The bandwidth supports higher-frequency closed-loop designs, while the slew rate determines how quickly the output can move through signal transitions. The single-amplifier configuration also reduces board area and power consumption compared with using a dual or quad package when only one amplifier is required.
The TLV2771 family combines high slew rate and bandwidth with rail-to-rail output swing and high output drive. These characteristics make the device useful in active filters, signal buffers, level translators, transducers, and low-voltage analog front ends. Its CMOS implementation is particularly appropriate when low quiescent power and operation from a compact supply are more important than the very lowest input offset voltage available from precision bipolar amplifiers.
Typical uses include sensor signal conditioning, communications-channel interfaces, audio and control-signal paths, industrial acquisition modules, and portable instrumentation. The 5.1 MHz bandwidth provides useful margin for moderate-frequency active filtering, while the 10.5 V/us slew rate improves large-signal response compared with slower general-purpose CMOS amplifiers. The 8-SOIC package supports conventional surface-mount assembly and thermal copper patterns.
When designing around the TLV2771ID, account for output-swing limits under load, input common-mode range, capacitive-load stability, and shutdown-pin logic. Place bypass capacitance close to the supply pins, preserve the manufacturer-recommended feedback topology, and verify settling time at the intended closed-loop gain. These checks are especially important when driving ADC front ends, long interconnects, or capacitive sensor outputs.
This product record combines the device's principal electrical characteristics, package and thermal details, pin-location guidance, application-specific design guidance, and same-footprint alternatives. It also highlights practical selection trade-offs involving shutdown operation, bandwidth, slew rate, supply current, and input precision so engineers can determine whether the TLV2771ID matches both the electrical and mechanical requirements of a new design.
Alternativas drop-in para TLV2771ID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLV2771ID (mesmo formato e footprint) — diferindo em Package, Slew Rate, Gain-Bandwidth Product, Maximum Supply Voltage, Product Type.
TLV2771CD
✅ Drop-InConsulte o preço
Ver ficha técnica →TLV272IDR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLV271IDR
✅ Drop-InConsulte o preço
Ver ficha técnica →TLV2771ID Classificações máximas e características elétricas
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 circuit |
| Technology | CMOS operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Minimum Supply Voltage | 2.7 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/us |
| Supply Current Per Channel | 1 mA |
| Tipo de saída | Rail-to-rail output |
| Shutdown Function | Present |
| Faixa de temperatura de operação | -40 C to +125 C |
| Encapsulamento | 8-SOIC |
| Tipo de montagem | Surface mount |
| Product Status | Active |
Guia de Configuração de Pinos do TLV2771ID 8-soic
Configuração de pinos para TLV2771ID (pacote 8-soic). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TLV2771ID.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TLV2771ID é adequado para 6 aplicaçãos: Low-Voltage Sensor Signal Conditioning, Communications Signal Interface, Active Filtering and Control Loops, Portable Measurement and Monitoring, Audio and Low-Level Analog Paths, ADC and Digital Interface Buffering.
Low-Voltage Sensor Signal Conditioning
The TLV2771ID fits low-voltage sensor front ends that require a compact amplifier with more bandwidth than a slow precision-oriented device. Its 5.1 MHz gain-bandwidth product supports moderate-frequency closed-loop operation, while the 10.5 V/us slew rate allows the output to follow faster input transitions. With approximately 1 mA supply current per channel and operation from 2.7 V, it can buffer resistive, current-output, or low-level sensing elements without creating a large supply-demand burden. Place the amplifier in a conventional noninverting or inverting configuration, and verify that the sensor output remains inside the input common-mode range. The complete signal path should also be checked for sensor noise, offset drift, filter stability, and settling before conversion by an ADC.
Recomendado
Communications Signal Interface
The TLV2771ID is appropriate for communications and industrial interface stages that need higher slew rate than a general-purpose low-power amplifier. Its 10.5 V/us slew rate helps preserve large-signal transitions, and the 5.1 MHz gain-bandwidth product provides margin for modest filtering and buffering functions. The approximately 1 mA operating current per channel is useful in distributed or portable interface equipment. Use the amplifier to condition logic-level signals, bridge sensor outputs, or buffer a communications transceiver where the signal remains within the common-mode range. Validate attenuation, logic-level thresholds, channel bandwidth, crosstalk, output loading, and shutdown timing for the actual communication protocol. A powered-down input state must also meet the receiver’s requirement for a valid inactive level.
Recomendado
Active Filtering and Control Loops
The TLV2771ID can implement active filters and servo-style control loops that benefit from its 5.1 MHz gain-bandwidth product and 10.5 V/us slew rate. These characteristics provide useful speed margin in second-order filters, error amplifiers, and waveform-shaping stages while keeping operating current near 1 mA per channel. The amplifier should be compensated according to the selected noise gain and load, particularly when driving ADC inputs, long cables, or capacitive loads. Evaluate phase margin, closed-loop gain, output swing, and expected component tolerances before production. For filters with stringent amplitude or phase accuracy, include amplifier offset, bias-current effects, and temperature drift in the error budget rather than relying only on nominal bandwidth and slew-rate figures.
Recomendado
Portable Measurement and Monitoring
The TLV2771ID suits portable measurement modules where a 2.7 V minimum supply and approximately 1 mA supply current are valuable, but the signal path still needs faster dynamics than an ultra-low-power amplifier provides. Its 5.1 MHz gain-bandwidth product can support precision-input buffering, threshold detection, and active gain stages, while the 10.5 V/us slew rate improves response to transients. Use suitable input protection and filtering because sensor leads can introduce ESD, motor noise, and capacitive loading. Confirm the amplifier’s common-mode range, output swing, and shutdown behavior across the full battery-voltage range. Low supply current alone does not establish total system power, so include quiescent current, load current, and shutdown leakage in the portable power budget.
Recomendado
Audio and Low-Level Analog Paths
The TLV2771ID can serve as a general-purpose amplifier in low-level audio or control paths where rail-to-rail output and fast transient response are important. The 10.5 V/us slew rate helps reduce slew-related distortion on changing waveforms, and the 5.1 MHz gain-bandwidth product provides more bandwidth than typical low-power audio stages. Its approximately 1 mA operating current supports compact analog sections, although the circuit must remain inside the amplifier’s specified input and output ranges. Establish the required gain, minimum signal level, output loading, and total harmonic distortion before selecting the device. In battery-powered audio equipment, shutdown control can reduce consumption during inactive intervals, but the shutdown input state and timing must be checked to prevent clicks or unwanted signal transients.
Recomendado
ADC and Digital Interface Buffering
The TLV2771ID is useful as an ADC input buffer or digital-interface conditioning stage when the required bandwidth is moderate and operating current must remain low. Its 5.1 MHz gain-bandwidth product supports unity-gain or low-gain buffering, and the 10.5 V/us slew rate permits larger input transitions than a slow comparator-style amplifier. The rail-to-rail output helps preserve logic levels near the supply limits, subject to the actual output-swing specification and load current. Place the device close to the ADC or source to minimize trace pickup and add suitable bypass capacitance near the supply pins. Verify settling against the converter’s acquisition window, capacitive loading, kickback from the ADC, and shutdown timing so the output does not move unpredictably while the converter is sampling.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV2771ID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV2771CD | TLV272IDR | TLV271IDR |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier | Single amplifier |
Principais diferenciais
- Combines high dynamic performance with low operating current (vs TLV272IDR)
- Single-amplifier 8-SOIC implementation reduces board space (vs TLV2771CD)
- Supports low-voltage operation with rail-to-rail output (vs TLV271IDR)
Notas de projeto
Use the 5.1 MHz gain-bandwidth product to select a closed-loop gain that leaves adequate bandwidth margin for the signal of interest. The 10.5 V/us slew rate is the maximum large-signal transition capability, so confirm that the required output amplitude, frequency, and load do not create slew-rate distortion. For an ADC interface, include amplifier settling time and the converter’s acquisition window in the overall timing budget, then include an isolation resistor if capacitive kickback or capacitive loading could affect stability.
Place the supply bypass capacitor close to the positive supply and ground pins, and return its ground end through the shortest practical path on the PCB. The normal operating current is approximately 1 mA per channel, but total system demand also includes output current and leakage while shut down. Confirm that the shutdown logic is compatible with the external circuit and that the powered-down output cannot create an invalid level at the load. Do not infer input behavior during shutdown without checking the manufacturer guidance.
Do not assume that rail-to-rail output means the output can reach exactly the supply rails under every load. Check output-swing conditions, load current, input common-mode range, and supply headroom at the intended operating point. Also verify that an alternative amplifier uses the same 8-SOIC pin functions and shutdown polarity; a shared footprint does not by itself make biasing, logic levels, offset, bias current, or dynamic performance interchangeable.
Informações de conformidade
Compliance status must be confirmed from the Texas Instruments product documentation for the exact orderable MPN and manufacturing origin. No definitive compliance claim is made for TLV2771ID.