TXS0108EQPWRQ1 - 8-Bit Auto-Direction Level Shifter | TI
N.º da peça: TXS0108EQPWRQ1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0.55 | $0,55 |
| 10 | $0.5 | $5,00 |
| 100 | $0.42 | $42,00 |
| 500 | $0.4 | $200,00 |
| 1.000 | $0.39 | $390,00 |
TXS0108EQPWRQ1 Visão geral
A voltage level translator (also called a logic level shifter or voltage translation IC) is an interface component in the broader logic and interface IC family that safely bridges digital devices operating at different supply domains, for example a 1.8V microcontroller talking to a 5V sensor. Level shifters protect low-voltage I/O from overvoltage while preserving logic thresholds, edge rates, and signal integrity across the voltage boundary.
Key specifications include a wide VCCA range of 1.2V to 3.6V and VCCB range of 1.65V to 5.5V, enabling translation between almost any two common logic rails. Push-pull data rates reach 110 Mbps while open-drain operation supports 2 Mbps with integrated 10 kOhm pull-up resistors. The device also offers an OE pin for 3-state operation during power sequencing and classified HBM ESD level 2 and CDM level C6 robustness per TI data.
Architecturally, the TXS0108E uses one-shot edge-rate accelerators on each channel to improve rise times, combined with a 4 kOhm series pass-gate element; this open-drain-friendly structure means it is not recommended for applications needing high drive strength such as direct LED loads.
Typical applications include automotive infotainment and body-control module I/O translation, sensor and CAN-adjacent digital interfacing, and portable electronics bridging 1.8V/2.5V/3.3V memory or peripheral buses to 5V domains. All prices cited in this page are as of 2026-08-29.
Design tip: because of the internal pull-ups, avoid this family for signals requiring low-capacitance backplane conditions; for heavy push-pull loads choose the TXB0108 instead.
Alternativas drop-in para TXS0108EQPWRQ1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TXS0108EQPWRQ1 (mesmo formato e footprint) — diferindo em Translator Type, Operating Temperature, Package, Direction Control, Output Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
TXS0108EPWR
✅ Drop-In✓ Em estoque
$0.51 / unidade
Ver ficha técnica →TXB0108QPWRQ1
⚡ Mesmo encapsulamento✓ Em estoque
$0.68 / unidade
Ver ficha técnica →TXB0108PWR
⚡ Mesmo encapsulamento✓ Em estoque
$0.26 / unidade
Ver ficha técnica →NXB0108PW
⚡ Mesmo encapsulamento ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
SN74LVC8T245PWR
⚡ Mesmo encapsulamento ⚠️ Especificações não verificadas✓ Em estoque
$0.175 / unidade
Ver ficha técnica →TXS0108EQPWRQ1 Especificações
| Bits / Channels | 8 bidirectional channels |
| Translator Type | Auto-direction voltage level translator (open-drain and push-pull) |
| VCCA Supply Range | 1.2 V to 3.6 V |
| VCCB Supply Range | 1.65 V to 5.5 V |
| Max Data Rate (Push-Pull) | 110 Mbps |
| Max Data Rate (Open-Drain) | 2 Mbps |
| Direction Control | Not required (auto-direction sensing) |
| Tipo de saída | 3-state with OE pin |
| Encapsulamento | TSSOP-20 (PW) |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40C to +125C (AEC-Q100 grade 1) |
| Automotive Qualification | AEC-Q100 qualified |
| ESD HBM Classification | Level 2 |
| ESD CDM Classification | Level C6 |
| Status RoHS | Compliant |
Configuração de pinos do TXS0108EQPWRQ1
| Pino 1 | A1 — A-side data 1 |
| Pino 2 | A2 — A-side data 2 |
| Pino 3 | A3 — A-side data 3 |
| Pino 4 | A4 — A-side data 4 |
| Pino 5 | GND — Ground |
| Pino 6 | A5 — A-side data 5 |
| Pino 7 | A6 — A-side data 6 |
| Pino 8 | A7 — A-side data 7 |
| Pino 9 | A8 — A-side data 8 |
| Pino 10 | NC — No connect |
| Pino 11 | B8 — B-side data 8 |
| Pino 12 | B7 — B-side data 7 |
| Pino 13 | B6 — B-side data 6 |
| Pino 14 | B5 — B-side data 5 |
| Pino 16 | B4 — B-side data 4 |
| Pino 17 | B3 — B-side data 3 |
| Pino 18 | B2 — B-side data 2 |
| Pino 19 | B1 — B-side data 1 |
| Pino 20 | OE — Output enable; low = 3-state all I/O |
Aplicações típicas
TXS0108EQPWRQ1 é adequado para 6 aplicaçãos: Automotive Body Control Module I/O, I2C / Open-Drain Bus Level Shifting, Infotainment and Display Digital Interfaces, Portable / Battery-Powered Electronics, Industrial Sensor and Logic Interfacing, Networking and Communication Equipment.
Automotive Body Control Module I/O
The TXS0108EQPWRQ1 is AEC-Q100 grade 1 qualified (-40C to +125C) with HBM ESD level 2 and CDM C6 classification, making it well suited for automotive BCM signal translation between low-voltage MCUs and 5V sensor or actuator logic. Its auto-direction sensing removes firmware overhead for bidirectional lines, and the OE pin safely isolates I/O during power sequencing. Placed between a 3.3V MCU bank and a 5V chassis-logic domain, all eight channels translate independently at push-pull rates up to 110 Mbps.
Recomendado
I2C / Open-Drain Bus Level Shifting
The integrated 10 kOhm pull-up resistors and open-drain-tolerant architecture allow the TXS0108E to shift I2C and similar open-drain buses between 1.8V/3.3V and 5V domains at up to 2 Mbps, covering I2C standard and fast modes. Because each channel is auto-directional, SDA re-configuration happens without a direction pin. Designers should verify bus capacitance, since the 10 kOhm pull-ups limit fast-mode-plus performance on heavy loads; lower-value external pull-ups at the B-side can restore edge rates.
Recomendado
Infotainment and Display Digital Interfaces
In automotive infotainment head units and cluster displays, low-voltage SoCs (1.8V or 2.5V I/O) must communicate with 3.3V/5V peripherals such as touch controllers, EEPROM, and backlight control logic. The TXS0108EQPWRQ1 bridges these domains on eight channels with 110 Mbps push-pull capability, sufficient for SPI and parallel control buses. The TSSOP-20 package simplifies routing on dense boards, and AEC-Q100 grade 1 qualification supports the elevated cabin temperature environment.
Recomendado
Portable / Battery-Powered Electronics
Battery-powered designs commonly mix 1.8V flash/memory or SoC I/O with 3.3V or 5V peripherals. The TXS0108EQPWRQ1 accepts VCCA as low as 1.2V, accommodating exhausted-battery low-voltage rails, while translating cleanly to 5V domains. Its 3-state OE control lets a system manager float all eight lines during standby, minimizing leakage. Auto-direction operation saves microcontroller GPIO pins otherwise consumed by direction control on partially bidirectional buses.
Recomendado
Industrial Sensor and Logic Interfacing
Industrial control boards frequently pair 3.3V microcontrollers with legacy 5V sensor and logic subsystems. The TXS0108EQPWRQ1 translates eight such signals with automatic direction detection, easing migration of 5V-centric designs to modern MCUs. Push-pull rates up to 110 Mbps cover SPI, UART, and parallel handshake buses. Designers should avoid using it on lines that must sink heavy loads, since its 4 kOhm series element and pull-ups limit output drive strength.
Recomendado
Networking and Communication Equipment
Routers, switches, and line cards use the TXS0108EQPWRQ1 to bridge 1.8V PHY or ASIC management I/O to 3.3V/5V EEPROM, LED drivers, and supervisory logic. The 110 Mbps push-pull rating supports MDIO at high clock rates and other management buses, while auto-direction handling suits shared read/write lines. The OE pin supports clean bring-up sequencing when management rails power in different orders across a backplane.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TXS0108EQPWRQ1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TXS0108EPWR | TXB0108QPWRQ1 | NXB0108PW | 74LVC8T245PW |
|---|---|---|---|---|---|
| Package | TSSOP-20 (PW) | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Bits / Channels | 8 bidirectional | 8 bidirectional | 8 bidirectional | 8 bidirectional | 8 bidirectional (DIR-controlled) |
| Open-Drain Support (Internal Pull-Ups) | Yes (10 kOhm) | Yes (10 kOhm) | No | No | No |
| Direction Control | None (auto-direction) | None (auto-direction) | None (auto-direction) | None (auto-direction) | DIR pins required |
Principais diferenciais
- Open-drain capable with integrated 10 kOhm pull-ups (vs TXB0108QPWRQ1)
- Automotive AEC-Q100 grade 1 qualification (vs TXS0108EPWR)
- Auto-direction, no DIR pins (vs 74LVC8T245PW)
Notas de projeto
Power VCCA first or simultaneously with VCCB; hold OE low until both supplies are valid so all I/O stay in 3-state during sequencing. The datasheet allows any power-up order but the OE control prevents mid-ramp glitching into the 5V domain. Decouple VCCA and VCCB with 0.1 uF ceramic capacitors placed within 2 mm of the pins.
Do not use the TXS0108E on lines that must sink heavy loads (LEDs, relays): the internal 10 kOhm pull-ups and ~4 kOhm series pass element provide only weak drive. Also avoid weak external pull-ups below the internal 10 kOhm threshold interfering with auto-direction edge detection; keep bus capacitance low on open-drain channels to meet the 2 Mbps limit.
Keep traces short and reference a solid ground plane; the one-shot edge accelerators sharpen rise edges, so long stubs can cause reflections on 100 Mbps-class signals. Unused channels should have both A and B sides tied to ground or left floating per the datasheet recommendation, and APU/VCC pins must not be left unconnected on variants that expose them.
Informações de conformidade
AEC-Q100 qualified grade 1 per TI product data. RoHS/lead-free per standard TI automotive production. REACH and conflict-minerals declarations available from TI material certification page.
