Интегральные схемы

PIC16F1704-I/P

PIC16F1704-I/P - 8-bit 32MHz 7KB Flash MCU w/Op Amps | Microchip

The Microchip Technology PIC16F1704-I/P is an 8-bit PIC16F microcontroller featuring Intelligent Analog integration and eXtreme Low Power (XLP) technology, housed in a 14-pin PDIP (P) through-hole package. It runs at 32 MHz with a 200 ns instruction cycle, includes 7 KB (4K x 14) of Flash program memory, 512 bytes of RAM, and integrates on-chip operational amplifiers, a 10-bit ADC with computation, and Core Independent Peripherals (CLC, COG, Zero Cross Detect). A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC16F1704 belongs to Microchip's enhanced mid-range PIC16 family, sitting within the 8-bit MCU segment of the broader microcontroller taxonomy: MCU -> 8-bit MCU -> enhanced mid-range -> PIC16F -> PIC16F17x family. This device combines RISC Harvard architecture with C-compiler-optimized instruction set (49 instructions) and direct LED drive capability. Key differentiating features include on-chip op amps eliminating external analog circuitry, Peripheral Pin Select (PPS) for flexible signal routing, 10-bit ADC with automated averaging/computation, and Core Independent Peripherals that operate autonomously without CPU intervention. The device also features Zero Cross Detect for AC signal applications, Complementary Output Generator (COG) for power switching, and Configurable Logic Cells (CLC) for hardware logic customization. XLP technology delivers deep sleep currents below 1 µA. The architecture uses a 14-bit instruction word with 8-bit data path, 16-level hardware stack, and 31 kHz internal oscillator plus 32 MHz HFINTOSC. The integrated op amps can be configured as amplifiers, comparators, or ADC drivers, eliminating external components and reducing BOM cost. PPS allows remapping of digital peripherals to any I/O pin, simplifying PCB layout. Typical applications include LED lighting control, sensor signal conditioning with on-chip op amps, battery-powered IoT sensor nodes leveraging XLP, consumer appliance control, and small motor control using COG and PWM. The combination of analog integration and low power makes it ideal for cost-sensitive general-purpose embedded designs. When designing with this device, leverage PPS to simplify PCB layout and use Core Independent Peripherals to offload tasks from the CPU for lower power and latency. Note that the 14-pin PDIP package is suitable for prototyping and through-hole assembly, not high-volume SMT production. Use MPLAB X IDE and XC8 compiler for development. This page synthesizes distributor pricing, drop-in PIC16F1xxx family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

PIC16F1704-I/SL

PIC16F1704-I/SL - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC16F1704-I/SL is an 8-bit PIC microcontroller from the PIC® XLP™ 16F family, featuring 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and a maximum CPU clock of 32MHz, housed in a 14-pin SOIC (SL) package. The device operates from 2.3V to 5.5V and integrates intelligent analog peripherals including on-chip operational amplifiers, a 10-bit ADC, and core independent peripherals such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), and Zero Cross Detect (ZCD). The 'I' suffix indicates the industrial temperature grade of -40C to +85C. An 8-bit PIC microcontroller is a CMOS RISC-based computing core designed for deterministic, low-power embedded control. Within the broader taxonomy, PIC16F parts sit between PIC10/12/14 baseline families (smaller memory, fewer peripherals) and PIC18/PIC24 higher-end families (more memory, wider buses, DSP). The 'F' denotes Flash program memory (re-programmable in-circuit), and 'XLP' designates Microchip's eXtreme Low Power platform with nanoWatt sleep modes and sub-microamp RTC operation, making the PIC16F1704 well suited to battery-powered applications. Key specifications include: 32MHz internal oscillator, 14 I/O pins with Peripheral Pin Select (PPS) for flexible signal routing, hardware multiplier, 10-bit ADC with computation, two op-amps, one 8-bit DAC, two comparators, and enhanced PWM with dead-band control. The device supports ICSP (In-Circuit Serial Programming) for field firmware updates and includes an on-chip debugger interface. Architecturally, the PIC16F1704 uses an 8-bit ALU with a 14-bit instruction word, providing a code density advantage over traditional 8-bit CISC architectures. The Harvard bus structure separates instruction and data paths to allow simultaneous fetch and execute, and the 31-level hardware stack supports modular C programming. The MIPS/MHz ratio of 1 ensures deterministic interrupt latency critical for real-time control. Typical applications include: sensor signal conditioning using the integrated op-amps, low-power IoT sensor nodes leveraging XLP sleep modes, LED lighting control via the COG and PWM peripherals, battery management and metering, and consumer appliances requiring mixed-signal integration. The combination of analog front-end and digital control in a single 14-pin package reduces BOM cost and PCB area. When designing with this part, evaluate whether the 4K-word flash, 512-byte SRAM, and 14 I/O pins match application requirements. PPS provides pin-function remapping without board changes, but the 14-pin SOIC package has limited GPIO expansion; consider PIC16F1705 (20-pin) or PIC16F1708/1709 (28/40-pin) variants for higher I/O count. The internal 32MHz oscillator eliminates an external crystal but may not meet USB or precise timing needs. This page synthesizes distributor pricing from DigiKey/Mouser, drop-in package-compatible alternatives within the PIC16F family, and practical design notes covering op-amp configuration, ADC averaging, and XLP sleep-current measurements not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1704-I/ST

PIC16F1704-I/ST - 8-bit 32MHz 7KB Flash MCU 14-TSSOP | Microchip

The Microchip Technology PIC16F1704-I/ST is an 8-bit PIC16F microcontroller (MCU) running up to 32 MHz, with 7 KB Flash program memory (4K x 14 words), 512 B RAM, and intelligent analog peripherals, housed in a 14-pin TSSOP (ST) package. It belongs to the PIC16F170X/171X family and pairs an enhanced mid-range core with Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), Zero-Cross Detect (ZCD), and Peripheral Pin Select (PPS) for hardware-driven functional blocks. What is an 8-bit Flash MCU? An 8-bit Flash microcontroller integrates a CPU, non-volatile Flash program memory, RAM, peripherals, and I/O onto a single chip. The PIC16F1704 fits between smaller 8-pin PIC MCUs and larger 16-bit/32-bit devices, offering deterministic interrupt latency and low power consumption. It sits within the product hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. This makes it well suited to cost-sensitive general-purpose applications that still need on-chip analog. Key features include a 10-bit ADC with computation, two on-chip op-amps (for active filtering, signal conditioning, or PGA), an 8-bit DAC, up to two PWM/CCP modules, an on-chip high-speed comparator, and serial peripherals (EUSART, I2C, SPI). The device supports the XLP (eXtreme Low Power) sleep currents typical of the PIC16F1xxx family, making it suitable for battery-operated and energy-harvesting designs. PPS allows flexible peripheral-to-pin mapping, simplifying PCB routing. Typical applications include LED lighting drivers, battery chargers and monitors, sensor signal conditioning, low-cost fan/thermostat controls, consumer white goods, and portable IoT end-nodes. The op-amp + DAC + ADC trio lets designers replace several discrete analog components with the MCU alone. Designers should review the PIC16F1704 device-family datasheet and the device-specific silicon errata before committing a layout, as some analog channels and PPS mappings differ between pin variants.

Запрос цены Контакты

PIC16F1704T-I/SL

PIC16F1704T-I/SL - 8-Bit 32MHz MCU 7KB Flash | Microchip

The Microchip Technology PIC16F1704T-I/SL is an 8-bit PIC16F family microcontroller built on the enhanced mid-range core, delivering 32 MHz performance (8 MIPS) from 7KB of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM. It is housed in a 14-pin SOIC (SL) package with industrial -40C to +85C temperature rating and tape-and-reel packaging. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path, integrating CPU, RAM, Flash program memory and peripherals into one device. PIC microcontrollers (Peripheral Interface Controllers) use a RISC architecture with a small instruction set optimized for deterministic, low-power embedded control. The PIC16F1704 sits within Microchip's PIC16F1xxx enhanced mid-range product line, between the 8-bit baseline PIC10/12/16 families and 16-bit PIC24/dsPIC parts, and is targeted at cost-sensitive applications needing integrated analog. Key features of the PIC16F1704 include on-chip operational amplifiers (up to 2), a 10-bit ADC with up to 8 channels, an 8-bit DAC, two high-speed comparators, Core Independent Peripherals (CLC, COG, Zero-Cross Detect), PWM modules, CCP, and serial interfaces (EUSART, I2C, SPI). It also offers Peripheral Pin Select (PPS) for flexible signal routing and XLP (eXtreme Low Power) technology with nanoWatt sleep current as low as 50 nA typical. The PIC16F1704's enhanced mid-range core with a 14-bit instruction word delivers 8 MIPS at 32 MHz while preserving code compatibility with PIC10/12/16 baseline cores. Internal 32 MHz oscillator accuracy eliminates external crystal cost in many designs, and PPS allows designers to remap peripheral I/O to multiple physical pins - a significant advantage over older fixed-pin PIC parts. Typical applications include sensor signal conditioning with on-chip op-amps, LED lighting control with COG/CLC, battery chargers, motor control loops, low-power IoT edge nodes, and consumer white goods. The integrated analog front-end reduces external component count versus PIC16F1xxx parts without op-amps. When designing with this device, place a 0.1 uF decoupling capacitor within 5 mm of VDD, add a 10 uF bulk capacitor on VDD if the supply impedance exceeds 1 ohm, and use the PPS registers to route peripherals only to available remappable pins. Program the configuration words to set the oscillator mode, WDT, and code-protect before final code lock-down. This page synthesizes distributor pricing, drop-in Microchip same-package alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

PIC16F1705-E/ML

PIC16F1705-E/ML - 8-bit MCU, 32MHz, 14KB Flash, 16-QFN | Microchip

The Microchip Technology PIC16F1705-E/ML is an 8-bit PIC16F microcontroller unit (MCU) featuring 14KB Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 16-pin QFN (4x4 mm) package with extended (-40C to +125C) operating temperature. It integrates Intelligent Analog peripherals - on-chip operational amplifiers, an 8-bit DAC, a 10-bit ADC, high-speed comparator, and zero-cross detect - alongside Core Independent Peripherals (CLC, COG, NCO) and Peripheral Pin Select (PPS), enabling flexible pin mapping for compact designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripheral interfaces. Within the broader taxonomy, the PIC16F1705 belongs to the 8-bit MCU category (PIC16 family -> 8-bit PIC -> PIC microcontroller -> MCU -> microcontroller -> embedded processor -> semiconductor). Compared with 32-bit ARM Cortex-M parts, an 8-bit MCU consumes far less power, costs less, and delivers deterministic interrupt latency suitable for sensor nodes, human-interface devices, and battery-powered edge sensing. Key features of the PIC16F1705 include eXtreme Low Power (XLP) technology with deep-sleep currents in the nanoampere range, 12-bit ADC with computation, two operational amplifiers usable as rail-to-rail input stages, an 8-bit DAC, a 5-bit DAC, two comparators, a Zero-Cross Detect (ZCD) module, Configurable Logic Cell (CLC) blocks, Complementary Output Generator (COG), Numerically Controlled Oscillator (NCO), EUSART, I2C/SPI, CCP and PWM modules, and up to 12 I/O pins. The 32MHz internal oscillator eliminates the need for an external crystal in many designs. The PIC16F1705 uses a Harvard-architecture RISC core with a 14-bit instruction word and a single-cycle ALU, delivering ~32MIPS throughput. PPS allows remapping of digital peripherals to nearly any I/O pin, which simplifies PCB layout and reduces the need for trace-crossing rework. The on-chip op amps - a rarity in this package class - enable single-chip signal conditioning for sensor interfaces. Typical applications include IoT sensor nodes, battery-powered wireless sensor transmitters, LED lighting controllers with smooth dimming (ZCD + COG), small motor control loops, smoke/CO detectors, remote controls, capacitive-touch human-interface devices, and general-purpose logic-replacement designs. The extended -40C to +125C temperature range and AEC-Q100-style robustness make it suitable for industrial and harsh-environment deployments. When designing with this MCU, allocate at least one decoupling capacitor (100nF X7R) per VDD pin and a 10uF bulk capacitor near the IC. The ICSP/ICD pins (RB6/RA0 and RB7/RA1 equivalents on this device) must be brought out to a programming header or Tag-Connect footprint to support in-circuit debugging and field firmware updates. This page synthesizes distributor pricing, parametric drop-in alternatives from Microchip's pin-compatibility chart, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1705-E/P

PIC16F1705-E/P - 8-bit 32MHz XLP MCU 14KB Flash DIP-14 | Microchip

The Microchip Technology PIC16F1705-E/P is an 8-bit PIC16F family microcontroller featuring 14KB Flash program memory, 1KB SRAM, 32MHz internal oscillator, and on-chip Intelligent Analog peripherals, housed in a 14-pin PDIP through-hole package with -40C to +125C extended operating range. It combines Intelligent Analog integration with extreme low-power (XLP) technology for general-purpose embedded applications. A PIC microcontroller (Programmable Interface Controller) is a class of 8/16/32-bit RISC microcontrollers originally developed by Microchip and widely used in embedded systems for control-oriented tasks such as sensor interfacing, motor control, and low-power IoT endpoints. Within the Microchip taxonomy, the PIC16F1705 belongs to the PIC16F1 mid-range enhanced family, which adds Core Independent Peripherals (CIPs) such as CLC, COG, and Zero-Cross Detect to the traditional PIC16 mid-range core, enabling autonomous hardware-level task execution. Key differentiating specifications include 14KB (8K x 14 words) Flash, 1024 bytes SRAM, 32MHz maximum CPU speed (8 MIPS), a 10-bit ADC with computation, two on-chip op-amps, an 8-bit DAC, a high-speed comparator, two CCP modules producing complementary PWM output, plus CLC, COG, ZCD, PPS, and EUSART peripherals with I2C/SPI support. The device operates from 2.3V to 5.5V, supports nanoWatt XLP sleep modes with sub-uA currents, and includes a 32kHz LFINTOSC for low-power timing. Architecturally, the PIC16F1705 implements an enhanced mid-range 8-bit RISC core with a 14-bit instruction word, hardware multiplier, and Interrupt-on-Change (IOC) on most I/O pins. Core Independent Peripherals (CLC, COG, NCO, ZCD, CWG) operate without CPU intervention, allowing deterministic event handling while the CPU remains in sleep, which is critical for ultra-low-power sensor nodes. Peripheral Pin Select (PPS) provides flexible signal routing on the limited 14-pin package. Typical applications include consumer white goods (sensor front-ends, AC zero-cross detection with the ZCD peripheral and dimming using COG), low-power battery-powered IoT nodes that exploit the XLP sleep current, capacitive-touch user interfaces driven by on-chip op-amps and the ADC with computation, and small BLDC/PWM motor-control loops where the on-chip op-amp amplifies current-sense feedback. Industrial sensor conditioning and LED driver control are common use cases. Designers should plan for adequate decoupling (100 nF plus 10 uF bulk near VDD), in-circuit serial programming (ICSP) header with separate PGED/PGEC lines, and use of PPS to remap EUSART and PWM to convenient pins. For EMI robustness, place a ferrite bead on VDD if operating near a switching converter. This page synthesizes distributor pricing, Microchip cross-reference data, side-by-side parametric comparison against same-package alternatives, and PCB/EMC design notes that go beyond the manufacturer datasheet, giving an engineer everything needed to evaluate and adopt the PIC16F1705-E/P in production.

Запрос цены Контакты

PIC16F1705-E/SL

PIC16F1705-E/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip

The Microchip Technology PIC16F1705-E/SL is an 8-bit PIC microcontroller in the PIC16F family, featuring 14KB (8K x 14) Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 14-pin SOIC package with the -E extended (-40C to +125C) operating temperature range. The device combines Microchip's XLP (eXtreme Low Power) technology with intelligent analog peripherals including on-chip operational amplifiers, a 10-bit ADC, an 8-bit DAC, comparators, and Zero-Cross Detect, making it well suited for mixed-signal general-purpose applications. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash), data memory (RAM), and peripheral interfaces on a single die. Within the embedded electronics hierarchy, an MCU sits between simple discrete logic and full microprocessors; the PIC16F family occupies the mid-range 8-bit tier that trades raw clock speed for deterministic latency, low power consumption, and rich on-chip analog integration. XLP further extends battery life by offering nanoWatt sleep currents in the microamp range, enabling years of operation from a single coin cell. The PIC16F1705's key differentiating features include Core Independent Peripherals (CLC, COG, NCO, CCP/PWM), Peripheral Pin Select (PPS) for flexible signal routing, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and I2C/SPI interfaces. Two on-chip op amps and a Zero-Cross Detect block allow direct interfacing with sensors and triac-driven loads without external analog front-end components. The 10-bit ADC with up to 12 channels and computation capabilities supports automated averaging and threshold comparison in firmware. Typical applications include LED lighting controllers, capacitive touch user interfaces, sensor signal conditioning, small appliance control, battery-powered IoT sensor nodes, and consumer white goods. Its 14-pin SOIC footprint and Microchip ecosystem (MPLAB X IDE, XC8 compiler, MCC code configurator) make it accessible for both prototyping on Curiosity development boards and high-volume production. When designing with the PIC16F1705, observe the supply voltage range of 2.3V to 5.5V, place a 0.1uF decoupling capacitor adjacent to each VDD pin, and configure PPS carefully to avoid pin conflicts between remappable peripherals. For noise-sensitive analog measurements, disable unused digital inputs and use the dedicated ANSEL register to prevent digital input buffers from corrupting the ADC result. This page synthesizes distributor pricing, drop-in same-package alternatives, application-specific design guidance, and a comparison table with parametric detail that the manufacturer datasheet alone does not provide.

Запрос цены Контакты

PIC16F1705-I/P

PIC16F1705-I/P - 32MHz XLP 8-Bit MCU | Microchip

The Microchip Technology PIC16F1705-I/P is an 8-bit flash microcontroller operating at up to 32 MHz, with 14 KB of program memory, 1024 bytes of RAM, and a 10-bit ADC in a 14-pin PDIP package. It combines Intelligent Analog integration with extreme low-power XLP operation and includes on-chip operational amplifiers, Core Independent Peripherals, Peripheral Pin Select, and Zero-Cross Detection. A microcontroller is a programmable integrated circuit containing a processor core, memory, and peripherals on one semiconductor die. Within the product hierarchy, the PIC16F1705 is a PIC16 8-bit flash microcontroller, a compact embedded-control platform used to sense inputs, run control algorithms, and operate actuators. Its integrated analog resources can reduce component count in cost-sensitive designs that need measurement, signal conditioning, and control functions without requiring a separate analog IC. The PIC16F1705-I/P provides 8K words of flash program memory, equal to 14 KB, alongside 1024 bytes of data memory. Its 10-bit ADC supports analog-to-digital conversion, while the integrated operational amplifiers can implement signal-conditioning or current-feedback functions. Core Independent Peripherals include CLC and COG, and Zero-Cross Detection supports AC-related timing functions. Peripheral Pin Select provides flexible routing options, and XLP technology targets low-power operation in embedded products. The device operates from a single low-voltage supply and uses a compact 14-pin through-hole package suitable for prototypes, control boards, industrial equipment, and educational platforms. At a maximum clock frequency of 32 MHz, the MCU provides useful processing headroom for protocol handling, state machines, signal conditioning, and mixed-signal control. Peripheral operation can continue in ways that reduce unnecessary CPU activity when the application is primarily waiting for an external event. Typical uses include low-cost sensor interfaces, industrial control modules, power-conversion controllers, lighting controls, compact instruments, and low-power embedded systems. The ADC, two on-chip operational amplifiers, CLC, COG, Zero-Cross Detection, and Peripheral Pin Select make the PIC16F1705 especially useful when the board area or component count must remain small. Its XLP feature set also makes it relevant to battery-operated and duty-cycled products. When designing around this controller, assign the analog inputs and op-amp pins according to the pin-description table in the manufacturer datasheet, and confirm the operating voltage and current limits against the exact device variant. Keep decoupling capacitance close to the supply pins, use a suitable oscillator configuration for timing accuracy, and verify that the chosen peripheral outputs remain available after Peripheral Pin Select assignments. This product page combines the manufacturer specifications, package information, practical application guidance, and drop-in replacement analysis to support schematic planning and component selection. It also highlights where a true pin-compatible replacement is available and where package or peripheral differences require a design review.

Запрос цены Контакты

PIC16F1705-I/SL

PIC16F1705-I/SL - 8-bit 32MHz MCU 14KB Flash 14-SOIC | Microchip

The Microchip Technology PIC16F1705-I/SL is a cost-effective 8-bit intelligent-analog flash microcontroller in a 14-pin SOIC (SL) package. It combines 14KB of Flash program memory, 1024 bytes of RAM, an 8-bit CPU core running at up to 32 MHz, and on-chip analog peripherals including operational amplifiers, a 10-bit ADC with computation, 8-bit/10-bit PWMs and Core Independent Peripherals (CLC, COG, Zero-Cross Detect). The device is part of the PIC16 XLP (eXtreme Low Power) family, delivering typical sleep currents in the nanoampere range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of digital and analog peripherals. Within the broader taxonomy, the PIC16F1705 belongs to the 8-bit MCU category, which sits below 32-bit MCUs in processing capability but excels in deterministic interrupt latency, low power, and low BOM cost. The PIC16F1705 series specifically targets "intelligent analog" applications where on-chip op amps, DACs, ADCs and PWM generation reduce or eliminate external analog ICs. Key features of the PIC16F1705-I/SL include 12 I/O pins, Peripheral Pin Select (PPS) for flexible signal routing, an integrated temperature indicator, an enhanced mid-range CPU instruction set (49 instructions / 16 stack levels), and a wide operating voltage range of 2.3V to 5.5V. The XLP nanoWatt technology provides multiple low-power modes (Sleep, Doze, Idle, and Peripheral Module Disable) suitable for battery-powered and energy-harvesting designs. Typical applications include sensor signal conditioning (using the on-chip op amps as gain/buffer stages), LED lighting control (using COG for constant-current regulation), battery chargers, small motor control loops, and IoT edge nodes where low sleep current is critical. The PIC16F1705-I/SL is the SOIC-14 variant of the PIC16F1705 family, which also ships in PDIP-14 (P), TSSOP-14 (ST), and QFN-16 (ML) options. When designing with this part, plan I/O assignment before PCB layout: PPS lets you remap digital peripherals to almost any pin, but analog pins are fixed. The on-chip op amps require careful reference and output routing to avoid loading the ADC inputs. For lowest power, transition the CPU to Sleep and use an interrupt (e.g., ZCD on AC mains) to wake only when needed. This page synthesizes real-time distributor pricing, drop-in alternatives in the 14-SOIC footprint, datasheet-grade specifications, and engineering design notes not consolidated in any single manufacturer document.

Запрос цены Контакты

PIC16F1705-I/ST

PIC16F1705-I/ST - 8-Bit 32MHz MCU 14KB Flash XLP | Microchip

The Microchip Technology PIC16F1705-I/ST is an 8-bit PIC microcontroller featuring 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and a maximum CPU clock of 32 MHz, housed in a 14-pin TSSOP package. It belongs to the PIC16F XLP family and combines Intelligent Analog integration (on-chip op amps, 10-bit ADC, 8-bit DAC, comparators, Zero-Cross Detect) with extreme low-power XLP peripherals to suit a wide variety of general-purpose applications. The -I suffix denotes the industrial -40°C to +85°C temperature grade, and /ST designates the 14-lead Thin Shrink Small Outline Package (TSSOP-14). An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, typically used for embedded control in cost- and power-sensitive applications. The PIC16F1705 sits within the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor device. Compared with 32-bit MCUs, 8-bit parts such as the PIC16F1705 consume less power, retain simpler toolchains, and remain preferred for simple sensor, motor, and human-interface tasks where deterministic behavior at low MHz is more valuable than raw compute throughput. Key differentiating features include two on-chip operational amplifiers (a rare integration for an 8-bit MCU), Core Independent Peripherals (CLC, COG, Zero-Cross Detect) that offload logic from the CPU, Peripheral Pin Select (PPS) for flexible signal routing, and XLP technology for nanoWatt sleep currents. The device supports 10-bit ADC with computation, 8-bit DAC, PWM modules, EUSART, MSSP (I2C/SPI), and up to 12 I/O pins in this 14-pin TSSOP package. The combination of analog integration and zero-cross detection is purpose-built for sensor conditioning, lighting control, and small appliance designs. Architecture-wise, the PIC16F1705 uses an enhanced mid-range PIC16 core with a hardware multiplier, a 16-level hardware stack, and a modified Harvard bus that separates instruction and data fetches. Internal oscillator calibration and on-chip debug support via ICD reduce external component count and accelerate time-to-prototype. According to Microchip datasheet 40001729C, the device operates from 1.8V to 5.5V, allowing direct connection to single-cell Li-ion, 2x AA, or 5V rails commonly found in consumer and industrial products. Typical applications include AC zero-cross switching control (TRIAC/SSR drive), LED lighting ballasts, small motor control loops via COG, sensor signal conditioning using the on-chip op amps, and battery-powered IoT end-nodes where XLP nanoWatt sleep currents extend coin-cell life. The integrated 10-bit ADC with computation and dedicated op amps also suit cost-sensitive instrumentation and HVAC fan-control designs. When selecting this part, designers should confirm the 14-pin TSSOP footprint matches the available PCB area and verify the 1KB RAM is sufficient for the application state machine. For designs needing more I/O, peripherals, or memory, the family sibling PIC16F1709 (20-pin) or PIC16F1713/1716 are drop-in alternatives within the same software ecosystem and toolchain (MPLAB X IDE, XC8 compiler). This page aggregates distributor pricing, parameter-level comparison versus same-package PIC16F family siblings, drop-in alternatives, and practical design guidance not found in a single manufacturer datasheet.

Запрос цены Контакты

PIC16F1705T-I/ML

PIC16F1705T-I/ML - 8-bit MCU, 14KB Flash, 32MHz, 16-QFN | Microchip

The Microchip Technology PIC16F1705T-I/ML is an 8-bit PIC® XLP™ microcontroller delivering 32 MHz CPU performance with 14 KB Flash program memory (8K x 14 words), 1024 bytes of RAM, and 256 bytes of EEPROM, all integrated in a compact 16-pin QFN (4x4 mm) package with exposed thermal pad. This tape-and-reel variant features the standard PIC16F1705 silicon die combined with Microchip's eXtreme Low Power (XLP) technology, making it well-suited for battery-operated applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a set of on-chip peripherals such as timers, ADC, communication interfaces, and I/O pins. Within the broader semiconductor taxonomy, MCUs belong to the microcontroller -> embedded controller -> integrated circuit hierarchy. The PIC16F1705 belongs to the PIC16F1xxx enhanced mid-range family, which targets mixed-signal applications where on-chip analog peripherals (op amps, DAC, comparators) coexist with digital logic. Key features include a 10-bit ADC with up to 12 channels, two operational amplifiers, one 8-bit DAC, two high-speed comparators with a 5-bit DAC reference, Core Independent Peripherals (CLC, COG, Zero Cross Detect), Peripheral Pin Select (PPS), and EUSART plus I²C/SPI serial interfaces. The device operates from 2.3 V to 5.5 V and is rated for the industrial -40 °C to +85 °C temperature range. Architecturally, the PIC16F1705 uses the enhanced mid-range 16-bit instruction word RISC core with a hardware stack and 49 instruction opcodes, providing deterministic interrupt latency and predictable execution times suitable for real-time control loops. The combination of op amps, comparators, DAC, and PWM enables closed-loop analog control without external components. Typical applications include LED lighting control with constant-current regulation, battery chargers, IoT sensor nodes, low-cost motor control, and consumer white goods. The QFN-16 footprint simplifies high-density PCB designs where board real estate is constrained. When designing with this part, allocate the exposed pad (EP) as a continuous copper pour tied to ground to provide both thermal dissipation and a low-impedance ground return. The PPS feature allows flexible assignment of digital peripheral pins to physical I/O, simplifying PCB routing. Note that the 'T' suffix indicates tape-and-reel packaging for high-volume assembly.

Запрос цены Контакты

PIC16F1705T-I/SL

PIC16F1705T-I/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip

The Microchip Technology PIC16F1705T-I/SL is an 8-bit PIC16 microcontroller featuring a maximum CPU clock of 32MHz, 14KB (8K x 14 words) of Flash program memory, and 1024 bytes of data RAM, housed in a 14-pin SOIC (SL) package. The 'T' suffix denotes Tape and Reel packaging, while 'I' indicates the industrial -40C to +85C operating temperature range. It is part of the PIC16F170X/171X family that integrates intelligent analog peripherals, including on-chip op amps and 10-bit ADC, with extreme low-power (XLP) technology. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and integrated peripherals such as ADC, timers, and communication interfaces. MCUs are hierarchically classified as embedded processors -> microcontrollers -> 8-bit microcontrollers. The PIC16F1705 falls in the low-pin-count, low-power category of general-purpose 8-bit MCUs, optimized for cost-sensitive, battery-friendly applications. Key features include 32MHz internal oscillator, 12-bit ADC with computation (ADC2), two on-chip operational amplifiers, two comparators, two 10-bit DACs, a 10-bit PWM, Core Independent Peripherals (Configurable Logic Cell, Complementary Output Generator, Zero-Cross Detect), Peripheral Pin Select (PPS) for flexible I/O mapping, and eXtreme Low Power (XLP) modes drawing down to nanoamp sleep currents. These features let a single chip replace multiple analog and discrete components in mixed-signal designs. The device uses a Harvard-architecture RISC core that executes most instructions in one clock cycle, providing deterministic throughput for real-time control loops. PPS decouples peripheral signals from physical pins, allowing PCB layout flexibility and easier routing on dense 14-pin boards. The ADC2 automates averaging, accumulation, and threshold comparison in hardware, offloading these tasks from the CPU and reducing firmware complexity. Typical applications include LED lighting controllers, sensor signal conditioning, battery-powered IoT nodes, and consumer appliance user-interface modules. Its combination of small footprint, on-chip op amps, and low sleep current makes it well suited to compact mixed-signal designs where both analog conditioning and MCU logic are needed on a single die. When designing with the PIC16F1705, pay attention to the PPS mapping for analog and digital peripheral routing, since several pins are multiplexed. The 14-pin SOIC is footprint-compatible with many PIC16F1xxx 14-pin devices, simplifying PCB reuse across the family. The internal 32MHz oscillator tolerance is typically +/-1% over the industrial temperature range, which may require external calibration for timing-critical UART/SPI links. This page synthesizes distributor pricing, drop-in SOIC-14 alternatives, and practical design notes for the PIC16F1705T-I/SL not found on a single manufacturer or distributor page.

Запрос цены Контакты

PIC16F1705T-I/ST

PIC16F1705T-I/ST - 14KB Flash 8-bit MCU, 32MHz, 14-TSSOP

The Microchip Technology PIC16F1705T-I/ST is a cost-effective 8-bit Intelligent Analog flash microcontroller from the PIC® XLP™ 16F family, integrating 14KB (8K x 14) of self-programmable flash program memory and 1024 bytes of SRAM in a 14-pin TSSOP (ST) package. It operates at speeds up to 32MHz, delivers 10-bit ADC resolution, and includes on-chip op amps, an 8-bit DAC, Zero-Cross Detect, complementary output generator (COG), configurable logic cells (CLC), and Peripheral Pin Select (PPS) for maximum design flexibility. The wide 1.8V to 5.5V supply range plus eXtreme Low Power (XLP) sleep currents below 50 nA typical make it ideal for battery-powered and energy-harvesting applications. The PIC16F1705 belongs to the 8-bit microcontroller class, the broadest tier of the PIC microcontrollers family which sit above general-purpose MCUs in the embedded computing hierarchy. Unlike 16-bit dsPIC or 32-bit ARM Cortex devices, 8-bit PIC MCUs trade raw throughput for code density, deterministic interrupts, and ultra-low sleep current - qualities that continue to dominate low-cost sensor node, appliance, and consumer designs. The PIC16F1705 carries that philosophy one step further with on-chip analog peripherals (op amps, DAC, ZCD, COG, CLC) that historically required external components, reducing BOM and PCB area. Key differentiating features include two internal op amps (configurable for PGA/trans-impedance/buffer), a 10-bit ADC with computation, an 8-bit DAC, and the eXtreme Low Power (XLP) technology that allows deep sleep currents below 50 nA while retaining RAM and peripheral state. The device also provides enhanced mid-range core instruction set with hardware multiply, 49 instructions, and 16-level hardware stack. CLC, COG, and PPS are the 'core independent peripherals' that let timers, PWMs, and analog blocks interact without CPU involvement, freeing the core for power management or higher-level control. Typical applications span IoT sensor nodes, white goods and appliance control, LED lighting with analog dimming, battery chargers and fuel gauges, low-cost motor control loops using COG + op amp, and smoke/CO detector signal chains where ZCD and ultra-low standby current are decisive. Industrial use cases include 4-20mA loop transmitters, smart thermostats, and remote controls. Because the part shares the same Peripheral Pin Select map with the larger 20-pin PIC16F1709, code is portable up the family for future-proofing. When designing, plan for the 14-pin constraint early - PPS helps, but only one pin function can be assigned at a time. Use the CLC to offload timing-critical sequences from the core, and route analog signals on dedicated pins to avoid digital noise coupling. Decouple VDD with at least 100 nF plus 10 µF bulk, and respect the absolute-maximum VDD of 6.0V even though operating range stops at 5.5V. For low-power designs, verify that unused peripherals are explicitly disabled (PMDx registers) - the default reset state does not turn everything off. This page synthesizes distributor pricing, drop-in same-package alternatives, application companions and design notes that are not consolidated on the manufacturer datasheet page, giving procurement and firmware engineers a single reference for new designs and field replacements.

Запрос цены Контакты

PIC16F1707-E/ML

PIC16F1707-E/ML - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

The Microchip Technology PIC16F1707-E/ML is an 8-bit PIC® XLP™ flash microcontroller with 3.5KB (2K x 14 words) of program memory, 256 bytes of SRAM, and a 32MHz internal oscillator, housed in a 20-pin QFN (4x4 mm) package. It integrates two on-chip operational amplifiers, a 10-bit ADC with computation (ADC2), complementary output generator (COG), zero-cross detect (ZCD), and Peripheral Pin Select (PPS), providing a flexible analog and digital peripheral mix in a small footprint. An 8-bit PIC microcontroller is a Harvard-architecture CMOS device that executes a reduced instruction set (RISC) optimized for embedded control. PIC microcontrollers are widely used in consumer, industrial, and IoT applications because they pair deterministic interrupt response with low power consumption. Within Microchip's portfolio, the PIC16F1707 sits in the mid-range PIC16F1xxx family - positioned between baseline PIC10/12/16 devices and higher-end PIC18/PIC24 parts - and belongs to the XLP (eXtreme Low Power) sub-line, with idle currents in the microampere range. Key features include 3.5KB self-programmable flash, 256B SRAM, two op amps with configurable rails, a 10-bit ADC up to 28 channels, PWM, CCP, EUSART, I2C/SPI, and nanoWatt XLP sleep currents down to 20 nA typical. The integrated COG and ZCD make it well suited to motor control, TRIAC/SSR driving, and zero-cross switching applications that previously required a dedicated analog front end. The 20-pin QFN 4x4 mm footprint is among the smallest in the PIC16 line, making it attractive for space-constrained designs. Typical applications include LED lighting ballast, AC zero-cross switching, low-end BLDC/PMSM commutation assist, battery-powered sensor nodes, and consumer white-goods user-interface controllers. Design considerations include ensuring adequate ground copper under the exposed pad of the QFN for thermal dissipation and using the PPS feature to remap peripheral I/O to convenient package pins. This page synthesizes distributor pricing, drop-in QFN-20 alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select a pin-compatible substitute or migrate firmware between family variants.

Запрос цены Контакты

PIC16F1707-E/SO

PIC16F1707-E/SO - 8-Bit MCU, 2K Flash, 256B RAM | Microchip

The Microchip Technology PIC16F1707-E/SO is an 8-bit enhanced mid-range PIC16 microcontroller combining Intelligent Analog integration with extreme low-power (XLP) operation, housed in a 20-pin SOIC (7.50 mm body width) package. It integrates 2K Words of Flash program memory, 256 bytes of SRAM, and 10-bit analog peripherals for mixed-signal embedded designs. An 8-bit flash microcontroller is a single-chip computer that combines a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripherals on one die. Within the broader semiconductor taxonomy, the PIC16F1707 sits in the hierarchy: microcontroller -> embedded MCU -> 8-bit MCU -> RISC flash MCU -> mixed-signal MCU. Its PIC16 enhanced mid-range core executes one instruction per two clock cycles, balancing code density with deterministic interrupt latency for real-time control loops. Key features include on-chip operational amplifiers, a 10-bit Analog-to-Digital Converter (ADC), Core Independent Peripherals such as the Configurable Logic Cell (CLC, also called COG in some marketing copy), Zero Cross Detect, and Peripheral Pin Select (PPS) that reassigns digital peripheral I/O to physical pins at runtime. The device operates across 1.8V to 5.5V supply, supports eXtreme Low Power (XLP) sleep currents in the nanoamp range, and offers up to 14 I/O pins depending on package variant. Technical depth: the PIC16F1707 uses a Harvard RISC architecture with separate program and data buses, instruction pipelining, and a hardware interrupt controller. PPS removes the rigid peripheral-to-pin mapping of legacy PIC16 parts, allowing the same firmware to route USART, SPI, or PWM to any available I/O - reducing PCB layout iterations when the original pin assignment cannot be routed. Typical applications include sensor signal conditioning using the on-chip op amps, battery-powered IoT nodes, home appliance user-interface controllers, LED lighting controllers with analog dimming, and small motor control loops. The combination of XLP sleep current and analog integration suits coin-cell powered products where the MCU must wake briefly to sample a sensor and return to deep sleep. Design consideration: when migrating from a legacy PIC16F to PIC16F1707, verify that your code is recompiled against the latest XC8 compiler, since PPS requires runtime unlock of peripheral mapping before first use. Also confirm the SOIC-20 land pattern matches your board footprint, because some prior PIC16 parts ship in narrower 0.300" SOIC bodies. This page synthesizes distributor pricing, same-package drop-in alternatives from Microchip's PIC16F family, and application design notes not found in the standalone manufacturer datasheet.

Запрос цены Контакты

PIC16F1707-E/SS

PIC16F1707-E/SS - 8-Bit MCU, 32MHz, 3.5KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16F1707-E/SS is an 8-bit PIC® XLP™ microcontroller with 3.5KB (2K x 14) Flash program memory, 256 bytes RAM, and a 32MHz internal oscillator, housed in a 20-pin SSOP package. The "-E" suffix denotes the extended industrial temperature grade of -40°C to +125°C, and the "/SS" package designator identifies the 209-mil 20-lead Shrink Small Outline Package. An 8-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals (timers, ADC, communication ports, comparators) into a single chip. PIC microcontrollers are based on Microchip's proprietary RISC (Reduced Instruction Set Computer) architecture, which executes most instructions in a single clock cycle, enabling deterministic throughput at modest clock rates and very low active/standby current. The PIC16F1707 belongs to the enhanced mid-range PIC16 family, sitting between the baseline PIC10/12/16 families and the higher-end PIC18/dsPIC families, and it falls under the broader category of embedded microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. Key features include on-chip operational amplifiers (op amps), Core Independent Peripherals (CIP) such as the Complementary Output Generator (COG) and Zero Cross Detect (ZCD), and Peripheral Pin Select (PPS) for flexible pin function remapping. The device integrates a 10-bit ADC, multiple communication peripherals, and the XLP™ extreme-low-power technology that delivers nanoWatt sleep currents, making it well suited for battery-powered and energy-harvesting designs where quiescent current directly governs battery life. The PIC16F1707 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, executing most instructions in one instruction cycle (4 clock cycles) for up to 8 MIPS at 32 MHz. Its Flash memory supports in-circuit self-programming via ICSP, allowing firmware updates in the field. The combination of deterministic single-cycle execution, hardware CIP blocks that offload tasks from the CPU, and PPS that lets the designer reassign peripheral pins without board rework gives this MCU strong design flexibility for cost-sensitive general-purpose applications. Typical applications include low-power IoT sensor nodes, LED lighting controllers, consumer appliances, capacitive-touch user interfaces, battery chargers, and small motor-control loops. Its op amps and comparators simplify signal conditioning for sensor interfaces, while the COG and PWM peripherals enable complementary switching waveforms for power-conversion stages. The PIC16F1707-E/SS is most commonly chosen when designers need PIC16-family familiarity, on-chip analog, and low sleep current in a compact 20-pin footprint. When designing with this part, note that the SSOP-20 (209 mil) package has a relatively small copper pad area compared with QFN, so high-current GPIO drive (>25 mA per pin) requires care with trace width to stay within package thermal limits. PPS configuration must be locked against unintended changes at runtime if the firmware image can be reprogrammed, and unused op-amp inputs should be tied to mid-rail to avoid shoot-through current. This page synthesizes DigiKey and Mouser distributor pricing, drop-in Microchip same-family alternatives, and practical design notes not aggregated on the manufacturer product page.

Запрос цены Контакты

PIC16F1707-I/ML

PIC16F1707-I/ML - 8-Bit 32MHz MCU, 3.5KB Flash, 20-QFN | Microchip

The Microchip Technology PIC16F1707-I/ML is an 8-bit PIC16 microcontroller built on the eXtreme Low Power (XLP) platform, integrating Intelligent Analog peripherals including on-chip operational amplifiers, Core Independent Peripherals (Configurable Logic Cell, Complementary Output Generator, and Zero Cross Detect), and Peripheral Pin Select in a compact 20-pin QFN (4x4 mm) package. It executes instructions at up to 32 MHz from 3.5 KB of Flash program memory (2K x 14 words), with 256 bytes of SRAM and 256 bytes of EEPROM, addressing general-purpose embedded applications that demand mixed-signal integration without external analog components. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and programmable peripherals. The PIC16F1707 belongs to Microchip's PIC16F1xxx enhanced mid-range family, which sits within the broader 8-bit microcontroller category alongside competitors such as the Atmel AVR and STM8 families. By integrating two op-amps, a 10-bit ADC with computation, a 5-/8-bit DAC, and high-resolution PWM directly on-die, the device reduces bill-of-materials cost and PCB area for sensor-conditioning, lighting-control, and small-motor-drive designs. Headline specifications include a 32 MHz internal oscillator, 1.8-5.5 V wide operating voltage range, 14-channel 10-bit ADC, two on-chip op-amps capable of rail-to-rail input/output, four 10-bit PWM outputs, and ultra-low power consumption down to 20 nA in sleep mode. The device supports up to 18 I/O pins with individually selectable peripheral remapping via Peripheral Pin Select (PPS), giving designers routing flexibility previously reserved for higher-pin-count MCUs. Architecturally, the PIC16F1707 uses a 14-bit instruction-word RISC core with a hardware stack and 49 instruction types, combined with a 32 MHz internal oscillator and a four-phase clock pipeline that delivers 8 MIPS throughput. The integrated Core Independent Peripherals (CLC, COG, ZCD, NCO) operate without CPU intervention, offloading real-time waveform generation and signal conditioning. This combination makes the part attractive for power-supply housekeeping, LED dimming, and small BLDC/PMSM fan control where determinism and code simplicity matter. Typical deployments include IoT sensor nodes, battery-powered handheld instrumentation, fan/blower motor control, LED drivers and dimmers, consumer white goods user interfaces, and low-cost mixed-signal front-ends. The wide voltage range and eXtreme Low Power features also suit wearables and remote controls where coin-cell battery life extends into years. When designing with this device, budget at least 0.1 uF of decoupling per VDD pin plus a bulk capacitor near the voltage regulator, and verify that the chosen debug tool (PICkit 4, MPLAB Snap, or ICD 4) supports the device ID 0x3060. For new designs, prefer the PIC16F1713 (larger Flash, additional CLC) only if 3.5 KB of program memory proves insufficient. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip cross-reference data, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1707-I/P

PIC16F1707-I/P - 8-bit 32MHz MCU 3.5KB Flash DIP-20 | Microchip

The Microchip Technology PIC16F1707-I/P is a cost-effective 8-bit microcontroller (MCU) from the PIC16F170X/171X family, delivering 32MHz CPU performance with 3.5KB (2K x 14 words) of Flash program memory in a 20-pin PDIP through-hole package. It integrates Intelligent Analog peripherals including on-chip operational amplifiers, 10-bit ADC, 5-/8-bit DAC, Zero Cross Detect (ZCD), and Core Independent Peripherals (CIPs) such as the Complementary Output Generator (COG) and Peripheral Pin Select (PPS), providing exceptional design flexibility for cost-sensitive embedded designs. An 8-bit microcontroller is a single-chip computer built around an 8-bit data bus CPU, integrating program memory (Flash/ROM), data memory (RAM), non-volatile EEPROM, and a rich set of on-chip peripherals (timers, ADC, communication ports, comparators). PIC microcontrollers from Microchip use a Harvard RISC architecture and are classified under the broader category of microcontrollers -> microprocessors -> semiconductor ICs. The PIC16F1707 belongs to the extreme low-power (XLP) family optimized for battery-powered and energy-harvesting applications, where active current in the microamp range and sleep currents in the nanoamp range extend operating life. Key features of the PIC16F1707-I/P include 256 bytes of RAM, 256 bytes of EEPROM, two op-amps, one 10-bit ADC with up to 12 channels, one 5-bit DAC, one 8-bit DAC, four 8-bit timers, one 16-bit timer, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), two SPI/I2C capable Master Synchronous Serial Port (MSSP) modules, and four Configurable Logic Cell (CLC) blocks. The device operates from 2.3V to 5.5V across -40C to +85C industrial temperature range, with nanoWatt XLP technology providing <50 nA typical sleep current. The PIC16F1707 uses an enhanced mid-range 8-bit RISC core with 49 instructions and 16-level hardware stack, supporting interrupt latency of just 5 instruction cycles. Its CIP architecture allows peripherals such as the COG and CLC to operate autonomously without CPU intervention, dramatically reducing firmware complexity for power-conversion, motor-drive, and signal-conditioning applications. Typical applications include LED lighting controllers, DC-DC converters, battery chargers, small appliance controls, sensor signal conditioning, low-cost fan/thermostat controllers, and IoT edge nodes. The on-chip op-amps and DAC make it particularly attractive for closed-loop analog control designs that previously required dedicated analog ICs. When designing with this device, plan for a 20-pin PDIP footprint and ensure MPLAB X IDE with XC8 compiler is used for firmware development. The internal 32MHz oscillator eliminates the need for an external crystal in most applications, saving two PCB pins and reducing BOM cost. This page synthesizes DigiKey distributor pricing, Microchip internal cross-reference data, drop-in alternatives (PIC16F1705, PIC16F1704, PIC16F1707-I/ML), and practical design notes not aggregated in the manufacturer datasheet.

Запрос цены Контакты

PIC16F1707-I/SO

PIC16F1707-I/SO - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

The Microchip Technology PIC16F1707-I/SO is an 8-bit PIC16 enhanced mid-range flash microcontroller featuring 3.5KB (2K x 14 words) of program Flash, 256 bytes of SRAM, and 128 bytes of EEPROM, operating at up to 32MHz instruction rate in a 20-pin SOIC package. The device integrates Intelligent Analog peripherals including on-chip operational amplifiers, a 10-bit ADC with Computation (ADC2), complementary output generator (COG), zero-cross detect (ZCD), and Peripheral Pin Select (PPS), while consuming only tens of microamps in sleep thanks to Microchip's eXtreme Low Power (XLP) technology. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile working RAM, digital I/O, and on-chip peripherals. The PIC16F1707 belongs to the 8-bit MCU class, sitting in the product hierarchy: 8-bit microcontroller -> PIC16 family -> enhanced mid-range core with nanoWatt/XLP technology -> low-cost general-purpose MCU with integrated analog. This category targets cost-sensitive, low-power embedded applications where integrating analog functions on-chip reduces BOM and PCB area. Key specifications include a 200ns instruction execution time, 14-bit wide instructions, 1.75KB usable Flash, 256B SRAM, and support for 32kHz to 32MHz oscillator operation. The 20-pin SOIC package exposes up to 18 I/O pins depending on configuration, with PPS allowing flexible peripheral-to-pin mapping. The device supports 1.8V to 5.5V wide operating voltage, making it suitable for both 3.3V and 5V designs without level shifters. The PIC16F1707 utilizes Microchip's enhanced mid-range 8-bit RISC core with a 14-bit instruction set and a hardware stack, providing deterministic interrupt latency suitable for real-time control. On-chip peripherals are designed as Core Independent Peripherals (CIPs), allowing the COG, ZCD, and timers to operate without CPU intervention - a critical advantage for low-power and deterministic motor, lighting, and power-conversion applications. Typical applications include LED lighting drivers, battery chargers, fan control, small appliance control, IoT sensor nodes, and general-purpose sensor interfacing. The integrated op-amps and 10-bit ADC simplify analog front-ends for temperature, light, and current sensing. Design trade-offs include the 8-bit datapath limiting arithmetic throughput compared to 32-bit MCUs, and the small 3.5KB Flash requiring careful code optimization for complex applications. When designing, ensure decoupling capacitors (100nF + 10uF bulk) are placed within 5mm of VDD pins. Configure unused I/O as outputs to minimize current consumption, and use the XLP sleep modes for battery-powered designs. The PPS feature requires careful review of datasheet pin-mapping tables to avoid conflicts. This page synthesizes distributor pricing, drop-in compatible alternatives from Microchip and competitors, application notes, and design considerations not consolidated in the manufacturer datasheet, providing an information-dense reference for engineers evaluating the PIC16F1707 for new designs.

Запрос цены Контакты

PIC16F1707-I/SS

PIC16F1707-I/SS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F1707-I/SS is an 8-bit PIC® XLP™ flash microcontroller combining Intelligent Analog integration with extreme low power operation, housed in a 20-pin SSOP package. The device delivers 32 MHz maximum CPU speed, 3.5 KB (2K x 14) of flash program memory, 256 bytes of RAM, and integrated 10-bit ADC peripherals. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus that integrates a CPU, RAM, non-volatile program memory, and peripheral IP. The PIC® XLP™ family is positioned in the broader taxonomy: 8-bit MCU -> RISC microcontroller -> flash microcontroller -> PIC® XLP™ -> microcontroller IC -> integrated circuit -> semiconductor. The PIC16F1707 sits at the low-cost, low-power end of the PIC16 mid-range family and adds analog-rich peripherals not commonly found in this segment. Key differentiating features include on-chip operational amplifiers, Core Independent Peripherals (CIPs) such as Complementary Output Generator (COG) and Zero Cross Detect (ZCD), and Peripheral Pin Select (PPS) that allows flexible signal routing. The device is well suited for applications where both analog front-end conditioning and digital control are required on the same die. Architecturally, the PIC16F1707 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, supporting C and XC8 compiler workflows. The combination of XLP sleep currents, hardware CIP blocks, and on-chip op-amps enables designers to remove external analog components, reducing BOM cost and PCB area. Typical applications include consumer appliance control, sensor signal conditioning, LED lighting drivers, low-power IoT edge nodes, and small motor-control signal chains. Designers select this part when they need more analog integration than a basic PIC16F150x, but less memory than a PIC16F171x. When designing with this device, choose a debug probe compatible with the ICSP™ programming interface and budget at least 2 mA of VDD current for the analog peripherals during full-load ADC sampling. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster PCB reuse and qualified second-source selection for the PIC16F1707-I/SS.

Запрос цены Контакты

PIC16F1707T-I/ML

PIC16F1707T-I/ML - 8-bit MCU, 2KB Flash, 10-bit ADC, XLP | Microchip

The Microchip Technology PIC16F1707T-I/ML is an 8-bit PIC microcontroller built on the enhanced mid-range x14 architecture, offering 2K words (3.5KB) of Flash program memory, 256 bytes of SRAM, and 128 bytes of EEPROM in a 20-pin QFN (4x4 mm, ML) package with exposed pad. It runs at up to 32 MHz instruction clock (200 ns instruction cycle) and supports an operating voltage range of 1.8V to 5.5V, with up to 18 I/O pins. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and a configurable set of peripherals. The PIC16F1707 belongs to the PIC16F family of 8-bit RISC microcontrollers from Microchip, designed for low-power general-purpose embedded applications. Within the broader taxonomy, MCUs fall under microcontrollers -> semiconductor -> integrated circuit. The PIC16F1707 adds the brand's XLP (eXtreme Low Power) technology and Intelligent Analog peripherals such as on-chip operational amplifiers, a 10-bit ADC with computation, and Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC) and Zero Cross Detect (ZCD). Key differentiating features of this device include its on-chip op amps (which eliminate external analog front-end circuitry), 10-bit ADC with automated Capacitive Voltage Divider (CVD) support for touch sensing, Peripheral Pin Select (PPS) for flexible signal routing, and a low-power Sleep mode drawing less than 20 nA typical. The exposed thermal pad on the QFN package provides a low thermal-resistance path (~30 C/W theta_JA typical on a 4-layer JEDEC test board), enabling reliable operation up to +125 C junction temperature in industrial environments. Internally, the PIC16F1707 uses a Harvard architecture with separate program and data buses, an 8-bit ALU, and 14-bit wide instructions. The CWG (Complementary Waveform Generator), NCO (Numerically Controlled Oscillator), and PWM modules make it well suited for driving power-conversion and lighting control loops without burdening the core. ECCP and standard CCP modules support motor-control and SMPS topologies. Typical applications include IoT sensor nodes, battery-powered consumer products, LED lighting controllers, touch-button user interfaces, low-end BLDC motor control, and home-automation appliances. Designers select this part when they need intelligent analog integration (op amps + ADC + DAC) and CIPs in a very small 4x4 mm QFN footprint. When designing with the PIC16F1707T-I/ML, pay close attention to the decoupling scheme - place a 100 nF ceramic capacitor on VDD as close as possible to the pin, plus a bulk 1 uF or larger tantalum/ceramic capacitor. The exposed pad MUST be soldered to the PCB ground plane to meet the package's thermal and electrical ratings; an unsoldered thermal pad can raise junction temperature by 20-30 C under typical loads. This page combines verified distributor pricing, a pin-compatible cross-reference set sourced from Microchip's own part selector, and practical design notes that complement (not duplicate) the manufacturer datasheet.

Запрос цены Контакты

PIC16F1707T-I/SO

PIC16F1707T-I/SO - 8-Bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F1707T-I/SO is an 8-bit PIC microcontroller built on the enhanced mid-range PIC16 core, delivering 32MHz (200ns instruction cycle) performance with 3.5KB (2K x 14) of self-programmable Flash program memory in a 20-pin SOIC package supplied on Tape and Reel. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, program memory, data RAM, and a configurable mix of digital and analog peripherals around a shared internal bus. The PIC16F1707 sits within the wider PIC microcontroller family, which itself belongs to the broader category of microcontrollers, embedded controllers, and ultimately semiconductors. The 8-bit class targets cost-sensitive, low-power applications that do not require the arithmetic throughput of 16- or 32-bit cores but still benefit from on-chip intelligence. The PIC16F1707 integrates intelligent analog features including on-chip operational amplifiers, a 10-bit ADC with computation, two 8-bit DACs, and Core Independent Peripherals such as the Complementary Output Generator (COG) and Zero Cross Detect (ZCD). Peripheral Pin Select (PPS) allows flexible remapping of digital peripherals to pins. The eXtreme Low Power (XLP) technology delivers nanoWatt sleep currents suitable for battery-powered designs. Architecture is built around a RISC-style Harvard core with 49 instructions, hardware stack, and 16-level deep subroutine support. The device operates from 1.8V to 5.5V across -40C to +85C industrial temperature range, with on-chip oscillator and 32kHz low-power internal oscillator for low-power modes. Hardware peripherals include enhanced USART, MSSP for I2C/SPI, CCP, and timers. Typical applications include consumer appliance control, LED lighting, battery chargers, sensor signal conditioning, and general-purpose embedded control where low power and on-chip analog integration reduce BOM. In IoT edge nodes and wearables, the XLP sleep modes extend battery life. In industrial sensor transmitters, the on-chip op amps condition bridge or thermocouple signals directly. When designing with this part, reserve one ICSP/ICD pin pair (PGC/PGD) for in-circuit programming and debugging. Configure PPS only after checking the PPS locking register to avoid unintended remapping. Always derate the ADC input below the absolute maximum ratings. This page synthesizes Microchip datasheet specifications, distributor stock and pricing, real drop-in alternatives, and engineering design notes - giving you a single reference that goes beyond the datasheet cover page.

Запрос цены Контакты

PIC16F1707T-I/SS

PIC16F1707T-I/SS - 8-bit MCU, 3.5KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16F1707T-I/SS is an 8-bit Flash microcontroller in the PIC16F170X/171X family with 3.5KB self-programmable Flash program memory, 256 bytes of RAM, and a 20-pin SSOP (SS) package. It combines Intelligent Analog integration with extreme low-power (XLP) technology, suiting it for general-purpose applications that need on-chip op-amps, 10-bit ADC, and Core Independent Peripherals such as the Configurable Logic Cell (CLC), Complementary Output Generator (COG), and Zero Cross Detect (ZCD). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a configurable set of peripherals (ADC, timers, communication ports, comparators) into one package. The PIC16F1707 belongs to the 8-bit PIC mid-range family, sitting hierarchically under: PIC16F1707 -> PIC16F170X family -> 8-bit PIC microcontrollers -> PIC microcontrollers -> Microchip microcontrollers -> microcontrollers -> semiconductors -> ICs. Within the broader system, MCUs are the decision-making brain of an embedded product, executing firmware that reads sensors and drives actuators while the supporting power, passives, and analog ICs provide clean rails and signal conditioning. Key features of this part include 3.5KB (2K Word) self-programmable Flash, 256B SRAM, a 10-bit ADC, on-chip op-amps, peripheral pin select (PPS), and an industrial temperature range of -40C to +85C. The 20-pin SSOP package keeps board area minimal while exposing sufficient I/O for mixed-signal front-ends. XLP technology delivers nanoWatt sleep currents, enabling battery-powered designs to meet years-long standby targets. Internally, the PIC16F1707 uses Microchip's enhanced mid-range 8-bit core with a 16-bit instruction word and an 8-level hardware stack, paired with a 16 MHz internal oscillator (no external crystal required for many designs). PPS lets you remap digital peripherals onto multiple physical pins, simplifying PCB layout and reducing routing congestion. Typical applications include low-cost sensor conditioning nodes, LED lighting controllers with analog dimming, battery chargers and monitors, fan/thermostat controllers, IoT edge nodes, and small motor control boards. The combination of op-amp + ADC + COG on one die lets engineers replace several discrete analog parts with one MCU. When designing with this device, choose the correct configuration bits (fuses) for the oscillator, watchdog, brown-out and code protection early; incorrect fuse settings are the most common field-bricked boards. Always verify the SSOP footprint land pattern against the manufacturer recommended PCB pad geometry. This page synthesizes distributor pricing, same-package drop-in alternatives (including on-site Microchip variants and cross-brand Microchip same-family options), and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1708-E/P

PIC16F1708-E/P - 8-Bit 32MHz MCU 7KB Flash 20-PDIP | Microchip

The Microchip Technology PIC16F1708-E/P is an 8-bit PIC microcontroller with XLP (eXtreme Low Power) technology, integrating Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and Peripheral Pin Select (PPS) in a 20-pin PDIP through-hole package. It delivers 32 MHz CPU performance, 7 KB (4K x 14) self-programmable Flash program memory, 512 bytes RAM, and 128 bytes EEPROM for general-purpose embedded control. An 8-bit PIC microcontroller is a small, deterministic processor based on a modified Harvard architecture with separate program and data buses, optimized for low-power, real-time control tasks. PIC MCUs sit in the taxonomy microcontroller -> embedded processor -> semiconductor device, and the PIC16F1708 specifically belongs to the PIC16F1 enhanced mid-range family, which adds CIPs and on-chip op amps to the classic mid-range core. XLP technology adds sleep currents in the nanoampere range, enabling battery-powered designs that wake only on peripheral events. Key features of this part include two on-chip operational amplifiers with rail-to-rail input/output, a 10-bit ADC with computation (ADC2), a 5-bit DAC, two comparators, an 8-bit timer (Timer2), a 16-bit timer (Timer1), and PWM modules with complementary waveform generation. Zero Cross Detect (ZCD), Configurable Logic Cells (CLC), and Complementary Output Generator (COG) peripherals allow sensorless AC mains monitoring and advanced switching without CPU intervention, reducing firmware complexity. The PIC16F1708-E/P is fabricated on an advanced process with on-chip debug and trace support, MPLAB X IDE compatibility, and free XC8 compiler support. The 'E' temperature grade extends operating range to -40C to +125C, making the part suitable for industrial and outdoor environments. The 20-pin PDIP package supports breadboard prototyping and through-hole manufacturing, simplifying hobbyist and low-volume industrial designs. Typical applications include LED lighting control with constant-current regulation, AC zero-cross detection for TRIAC dimmers, sensor signal conditioning with on-chip op amps, battery-powered IoT sensor nodes leveraging XLP, and low-cost motor control using COG and PWM. The integrated analog chain eliminates external op-amp ICs in many transducer interfaces. When designing with the PIC16F1708-E/P, allocate the ADC and op-amp channels early to avoid I/O contention, and use PPS to remap peripherals to convenient pins. For AC mains designs, configure the ZCD peripheral before enabling the COG or PWM output to prevent false triggering during power-up.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

PIC16F1704-I/P - 8-bit 32MHz 7KB Flash MCU w/Op Amps | Microchip

PIC16F1704-I/SL - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

PIC16F1704-I/ST - 8-bit 32MHz 7KB Flash MCU 14-TSSOP | Microchip

PIC16F1704T-I/SL - 8-Bit 32MHz MCU 7KB Flash | Microchip

PIC16F1705-E/ML - 8-bit MCU, 32MHz, 14KB Flash, 16-QFN | Microchip

PIC16F1705-E/P - 8-bit 32MHz XLP MCU 14KB Flash DIP-14 | Microchip

PIC16F1705-E/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip

PIC16F1705-I/P - 32MHz XLP 8-Bit MCU | Microchip

PIC16F1705-I/SL - 8-bit 32MHz MCU 14KB Flash 14-SOIC | Microchip

PIC16F1705-I/ST - 8-Bit 32MHz MCU 14KB Flash XLP | Microchip

PIC16F1705T-I/ML - 8-bit MCU, 14KB Flash, 32MHz, 16-QFN | Microchip

PIC16F1705T-I/SL - 8-bit MCU, 14KB Flash, 32MHz XLP | Microchip

PIC16F1705T-I/ST - 14KB Flash 8-bit MCU, 32MHz, 14-TSSOP

PIC16F1707-E/ML - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

PIC16F1707-E/SO - 8-Bit MCU, 2K Flash, 256B RAM | Microchip

PIC16F1707-E/SS - 8-Bit MCU, 32MHz, 3.5KB Flash, 20-SSOP | Microchip

PIC16F1707-I/ML - 8-Bit 32MHz MCU, 3.5KB Flash, 20-QFN | Microchip

PIC16F1707-I/P - 8-bit 32MHz MCU 3.5KB Flash DIP-20 | Microchip

PIC16F1707-I/SO - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

PIC16F1707-I/SS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F1707T-I/ML - 8-bit MCU, 2KB Flash, 10-bit ADC, XLP | Microchip

PIC16F1707T-I/SO - 8-Bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F1707T-I/SS - 8-bit MCU, 3.5KB Flash, 20-SSOP | Microchip

PIC16F1708-E/P - 8-Bit 32MHz MCU 7KB Flash 20-PDIP | Microchip