Товары (44.000+)

ICS551MT - 160 MHz 1:4 CMOS Clock Buffer | Renesas
ICS551MT

ICS551MT - 160 MHz 1:4 CMOS Clock Buffer | Renesas

Renesas ICS551MT is a low-cost, high-speed 1:4 CMOS clock fanout buffer with a maximum operating frequency of 160 MHz, a 3 V to 5.5 V supply range, and an 8-SOIC package. The device accepts one CMOS clock input and provides four buffered CMOS clock outputs, allowing a single source to drive multiple destinations without requiring multiple distribution stages. A clock buffer is a digital timing IC that reproduces a clock signal with controlled loading and drive characteristics. Within the product hierarchy, ICS551MT is a clock fanout buffer, a clock distribution IC, a timing IC, and ultimately a digital semiconductor. Its four-output topology is useful when a processor, controller, communications circuit, or data-conversion system requires several related clock domains that must originate from one low-jitter reference. Key features include 160 MHz maximum frequency, 1:4 fanout capability, CMOS input and output interfaces, and operation from 3 V to 5.5 V. The 8-SOIC package supports conventional surface-mount assembly while keeping the board footprint compact. The manufacturer identifies the ICS551 family as a low-cost, small clock-buffer option within the Clock Blocks family. The IC provides four independently usable outputs rather than requiring a cascading buffer arrangement. Each output can therefore feed a separate circuit, reducing distribution complexity and avoiding the need to reproduce the source clock multiple times. The exact output rise time, output skew, input-output delay, propagation delay, and operating-temperature limits are not disclosed in the supplied verified data and should be confirmed in the Renesas 551 datasheet before a timing-critical design is released. Typical uses include general-purpose clock distribution in embedded systems, communications equipment, industrial control electronics, and consumer or computing subsystems. The single-input, four-output organization is particularly helpful where four loads share a common clock source and the PCB requires short, controlled clock routes rather than a long point-to-point connection. Designers should place the 0.01 uF VDD decoupling capacitor between pin 7 and pin 6 as close as possible to the device, following the Renesas 551 datasheet. The same source recommends an optional 33 ohm series termination resistor on each clock output when the trace exceeds 1 inch, helping control reflections on longer PCB interconnects. This page consolidates the verified distributor specifications, official application guidance, package details, pricing availability status, and engineering trade-offs for ICS551MT. It distinguishes documented electrical facts from parameters that still require confirmation, helping engineers make faster sourcing and design decisions without inventing missing timing or environmental data.

Запрос цены Контакты
ICS552R-01 - 200MHz 8-Output CMOS Clock Multiplier | Renesas
ICS552R-01

ICS552R-01 - 200MHz 8-Output CMOS Clock Multiplier | Renesas

Renesas Electronics ICS552R-01 is a clock generator, multiplier, and buffer that produces eight low-skew CMOS copies of a clock or a fundamental parallel-mode crystal, with a maximum frequency of 200MHz. The device is available in a 20-pin SSOP package with a 3 V to 5.5 V supply range. Its one-to-eight input-to-output ratio supports designs that need multiple synchronized clock copies without using eight separate oscillators. A clock multiplier is a clock and timing IC that accepts a reference signal, derives a higher-frequency clock, and distributes the result across multiple outputs. Within the electronics hierarchy, it belongs to clock generation and timing, then to clock and timing ICs, and finally to integrated circuits. Unlike a conventional crystal oscillator, the ICS552R-01 family can operate directly from a multiple input clock or a fundamental parallel-mode crystal, providing design flexibility for synchronous digital systems. Key features include eight low-skew outputs, CMOS output technology, PLL capability, and operation up to 200MHz. The one-to-eight output ratio is useful when multiple logic domains require related clocks. A 3 V to 5.5 V supply range permits integration with both 3.3 V and 5 V digital systems, while the 20-SSOP surface-mount format supports compact PCB layouts. The 0°C to 70°C range applies to the identified commercial-temperature variants; other ordering codes may represent different temperature grades. The ICS552R-01 combines clock generation, multiplication, and fan-out functions in one package. Each of the eight outputs provides a low-skew copy of the derived clock, reducing the number of separate clock-driver circuits required when several processors, FPGAs, memory devices, or communication controllers must receive related clock signals. The PLL architecture and broad maximum operating frequency make the device useful when the source clock does not directly match the required system frequency. Typical applications include synchronous processor clock distribution, FPGA or ASIC clock fan-out, memory-controller clock distribution, communications-interface clocking, and general-purpose digital clock trees. It is especially relevant when one source must feed multiple loads while maintaining consistent frequency relationships. The device also supports systems that prefer external fundamental crystals or externally generated multiple clocks over a dedicated oscillator. When laying out the circuit, treat all eight outputs as high-speed clock nets and follow the manufacturer’s recommended termination and decoupling arrangements. Keep clock traces short, provide a continuous ground reference, and avoid routing outputs through uncontrolled impedance discontinuities. Confirm output-drive, jitter, skew, and load-current requirements against the manufacturer datasheet before choosing series termination or a fan-out topology. This product page combines the ICS552R-01 operating limits with practical clock-distribution guidance, ordering-code distinctions, lifecycle considerations, and a comparison framework for evaluating compatible 20-SSOP alternatives. Use the manufacturer pin-description table and electrical characteristics as the final authority for board implementation and production qualification.

Запрос цены Контакты
ICS553MI - 1:4 200 MHz Clock Buffer | Renesas Electronics
ICS553MI

ICS553MI - 1:4 200 MHz Clock Buffer | Renesas Electronics

Renesas Electronics ICS553MI is a low-skew 1:4 clock fanout buffer with a maximum operating frequency of 200 MHz, CMOS inputs and outputs, a 2.375 V to 5.25 V supply range, and an 8-SOIC package measuring 0.154 inch, or 3.90 mm, in width. It is positioned as the lowest-skew, small clock buffer in the ICS ClockBlocks family. A clock fanout buffer is a clock-management IC that receives one periodic signal and distributes multiple synchronized copies to several destinations. The ICS553MI belongs to the fanout buffer subclass of clock and timing ICs, within the broader clock-buffer, clock-driver, and clock-management semiconductor hierarchy. Its 1:4 fanout ratio makes it suitable where one source must feed four loads without redesigning the clock tree. The primary verified specifications are a 1:4 fanout ratio, 200 MHz maximum frequency, CMOS input and output interfaces, and a 2.375 V minimum operating supply voltage with a 5.25 V maximum. The 8-SOIC package supports conventional surface-mount assembly while providing four buffered outputs. These details distinguish it from single-output clock devices, lower-frequency buffers, and devices requiring more than four outputs. The low-skew architecture is intended to minimize output-to-output timing displacement, making the device relevant to synchronous systems in which downstream circuits require closely related clock edges. Exact propagation delay, output-to-output skew, rise time, fall time, output impedance, and input pulse-width limits are not present in the supplied verified data and should be taken from the manufacturer datasheet before timing closure. Typical uses include processor and FPGA clock distribution, communications-interface clock fanout, data-converter clocking, memory-interface timing, and general-purpose digital clock-tree branching. In each case, the single input can feed four destinations while the 200 MHz operating limit defines the upper frequency envelope. The CMOS interfaces also allow the device to operate across a 2.375 V to 5.25 V supply range, subject to the input and output voltage limits in the datasheet. The principal design consideration is timing verification. Engineers should check the worst-case input-to-output and output-to-output skew across process, voltage, and temperature, rather than relying only on the 200 MHz headline frequency. Supply decoupling, input slew rate, trace loading, and the number of clock destinations also require review because they affect edge quality and timing margin. This page consolidates the verified manufacturer and distributor information, distinguishes confirmed specifications from unavailable data, and documents practical clock-tree considerations. It also explains the absence of verified drop-in substitutes so engineers can avoid assuming that a shared package or similar frequency rating guarantees pin-to-pin compatibility.

Запрос цены Контакты
ICS553MIT - 1:4 200MHz Low-Skew Clock Buffer | Renesas
ICS553MIT

ICS553MIT - 1:4 200MHz Low-Skew Clock Buffer | Renesas

Renesas Electronics ICS553MIT is a low-skew clock fanout buffer that distributes one CMOS input clock to four CMOS outputs. It operates from a 2.375 V to 5.25 V supply and supports clock frequencies up to 200 MHz. The device is packaged in an 8-pin SOIC measuring 0.154 inches, or 3.90 mm, in width and belongs to the ICS ClockBlocks family. A clock fanout buffer is a clock-and-timing integrated circuit that regenerates and distributes one incoming clock signal across multiple outputs. Its place in the hierarchy is clock buffer, then clock distribution device, then clock-and-timing IC, and finally semiconductor. Fanout buffers are used where a source clock must drive several destinations while limiting loading, propagation variation, and signal degradation across a larger system. The ICS553MIT is identified as a low-skew, 1-to-4 clock buffer. Its four-output arrangement gives a processor, memory interface, communications circuit, or test instrument multiple usable clock outputs from one source. Operation up to 200 MHz makes it applicable to clock trees operating below that maximum frequency, while its 2.375 V to 5.25 V supply range supports common low-voltage digital systems. The CMOS input and CMOS outputs place the device in the logic and clock-and-timing categories. CMOS interfaces are suitable for modern digital systems because they support rail-to-rail operation in many designs and combine useful noise and power characteristics. Exact propagation delay, output-to-output skew, input-output skew, rise time, fall time, and current-consumption figures should be taken from the manufacturer datasheet before setting timing margins. Typical uses include distributing a reference clock among four digital loads, buffering a source oscillator before it reaches multiple logic blocks, and supporting compact communications, control, or instrumentation equipment. In each case, trace lengths should be arranged so that all four destinations receive clocks within the timing budget established for the system. The primary design consideration is timing margin across all four outputs rather than only the source-to-output path. Keep the input and output connections short, maintain a consistent return path, and place decoupling close to the supply pins. Account for the difference between edge arrival at the input and edge arrival at each load when defining setup and hold requirements. This product page combines the manufacturer part characteristics, source availability, pin-compatible alternatives, comparison criteria, and practical clock-distribution guidance. It is intended to accelerate component identification while keeping the final timing, layout, and qualification decisions with the system designer.

Запрос цены Контакты
ICS557G-03 - 200MHz Spread-Spectrum Clock | Renesas
ICS557G-03

ICS557G-03 - 200MHz Spread-Spectrum Clock | Renesas

The Renesas Electronics ICS557G-03 is a 200 MHz spread-spectrum clock generator and fanout buffer with one output, built in a 16-pin TSSOP package. It supports PCI Express Gen 1 and Ethernet clock requirements while reducing electromagnetic interference in PC and embedded systems. The device accepts clock or crystal inputs, uses a phase-locked loop, and supports HCSL and LVDS output configurations. A spread-spectrum clock generator is a timing semiconductor that intentionally varies clock frequency over a controlled range to spread radiated energy across a wider frequency spectrum. This technique lowers peak electromagnetic emissions without changing the fundamental 200 MHz operating frequency. In the broader semiconductor hierarchy, the ICS557G-03 belongs to the clock and timing IC family, where it combines clock generation, phase locking, distribution, and EMI-control functions. The principal features of the ICS557G-03 include a 200 MHz output, one clock output, PCI Express Gen 1 and Ethernet support, and a PLL-based architecture. The 16-TSSOP package is suitable for compact desktop, industrial, and embedded circuit boards. Its clock and crystal input options allow it to operate from an existing reference or a crystal source, while HCSL and LVDS output support accommodates high-speed differential signaling needs. Internally, the PLL provides the clock-generation mechanism required to create a stable reference-related output while applying frequency dithering for spectrum spreading. This is important in systems where reducing peak EMI improves electromagnetic-compatibility margin without requiring major changes to the downstream clock architecture. Because the ICS557G-03 is identified as both a spread-spectrum clock generator and fanout buffer, it can serve as the central timing source for compatible PCIe or Ethernet equipment. Typical applications include PCI Express Gen 1 cards, Ethernet interface equipment, embedded computer systems, industrial controllers, and compact PCs. The device is particularly relevant where radiated emissions from a high-speed reference clock could interfere with nearby radio, communications, or test equipment. It can also support clock distribution within systems that require a controlled low-frequency clock source. The primary design consideration is ensuring that the selected input reference, crystal, output loading, and downstream receiver comply with the requirements of the Renesas datasheet. Differential trace routing, stable return paths, controlled impedance, and correct termination are essential for stable HCSL or LVDS operation. PCB placement should minimize clock-loop area and keep sensitive routing away from noisy power-conversion stages. This product page combines the Renesas function description, verified distributor specifications, package details, practical implementation guidance, and same-package replacement analysis. It is intended to help engineers determine whether the ICS557G-03 satisfies the required frequency, interface, EMI-control, package, and sourcing constraints before beginning a board-level design.

Запрос цены Контакты
ICS557G-06 - 1:4 HCSL Clock Buffer | Renesas Electronics
ICS557G-06

ICS557G-06 - 1:4 HCSL Clock Buffer | Renesas Electronics

Renesas Electronics ICS557G-06 is a differential PCI Express clock fanout and multiplexer IC with a 1:4 output ratio, 200 MHz listed operating frequency, HCSL or LVDS inputs, and HCSL or LVDS outputs. The device is packaged in a 20-pin TSSOP package and is intended for systems requiring one selected differential clock input to be distributed across multiple outputs. A clock buffer or fanout buffer is a timing IC that reproduces an incoming clock signal across multiple outputs. Clock multiplexers add input selection, allowing a system to choose between clock sources while maintaining consistent output timing. The ICS557G-06 belongs to the clock buffer and clock multiplexer hierarchy, which falls under clock and timing ICs used in PCI Express cards, servers, industrial controllers, and other high-speed digital systems. The principal features of the ICS557G-06 include two differential input pairs, selection of one input pair, four differential output pairs, and support for HCSL and LVDS signal levels. Its one-to-four fanout architecture allows a selected source clock to reach several destinations while reducing the loading that would otherwise be imposed directly on the clock source. The 200 MHz frequency specification identifies the device's stated operating point for design planning. The ICS557G-06 does not use an internal PLL according to the component classification. Instead, it functions as a differential clock mux and fanout buffer: one of two input pairs is selected, and the selected clock is distributed through four differential output pairs. This architecture preserves the role of the original clock source while providing controlled fanout and selection for multi-output clock networks. Typical uses include PCI Express clock distribution, server backplane clock routing, industrial data-acquisition systems, network interface equipment, and test-and-measurement platforms. In a PCI Express design, the device can select the appropriate differential clock source and distribute it to multiple downstream circuits, reducing the fanout burden on the source and helping maintain consistent clock topology. Designers should verify differential impedance, output pair routing, return-path continuity, and input/output logic-level compatibility in the target system. Differential clock traces should be routed as a length-matched pair on a controlled-impedance board, with nearby high-speed or switching nodes kept away from the clock network. Decoupling, grounding, and unused-pin handling should follow the pin-description and layout guidance in the manufacturer datasheet. This page organizes the device function, interface characteristics, package details, application guidance, drop-in replacement information, and engineering design notes into one engineering-focused reference for evaluating the ICS557G-06 in PCI Express clock architectures.

Запрос цены Контакты
ICS557G-08 - 200MHz PCIe Clock Multiplexer | Renesas
ICS557G-08

ICS557G-08 - 200MHz PCIe Clock Multiplexer | Renesas

The Renesas Electronics ICS557G-08 is a PCI Express clock multiplexer IC with a 200 MHz output, one differential output pair, and a 16-pin TSSOP package. It uses a 2:1 multiplexing architecture to select one of two HCSL or LVDS input pairs and fan the selected clock into a differential HCSL or LVDS output pair. This arrangement gives a PCI Express clock source a practical way to switch between reference sources without changing the downstream clock architecture. A PCI Express clock multiplexer is a clock-and-timing IC used to route differential clock signals inside high-speed digital equipment. In the signal hierarchy, it belongs to the PCIe clock source and clock-driver category, combining input-pair selection, differential distribution, and PLL-based clock generation. HCSL means Host Clock Signal Level, while LVDS means Low-Voltage Differential Signaling; both are differential signaling methods suited to high-speed clock distribution. The ICS557G-08 supports a clock output frequency up to 200 MHz and is identified as a 2:1 multiplexer. Its principal features are dual input-pair selection, one differential output pair, support for HCSL or LVDS operation, and a surface-mount 16-pin TSSOP package. The 200 MHz operating point makes the device applicable to PCI Express clocking systems that require controlled selection between reference-clock sources. Its PLL-based architecture is important in a PCIe design because clock-source transitions can affect downstream jitter and system timing. The selected input pair is fanned out through a differential output stage, preserving the electrical signaling method expected by the receiving clock buffer or peripheral. Designers should still validate source-to-destination transition requirements, termination, return-path continuity, and receiver thresholds in the final channel. Typical uses include PCI Express endpoint clock distribution, server and workstation expansion-card designs, embedded PCI Express equipment, and industrial host systems that must select between two external reference clocks. The device can also be considered in test systems where a selectable differential clock source is needed for compatibility or fault-injection testing. When laying out a board, place the IC near the clock source and receiving device, provide a continuous reference plane beneath the differential route, and use impedance-controlled pairs with matched through or via structures. Decoupling should follow the manufacturer reference layout. Because this is a high-speed differential clock device, routing symmetry and connector or package-transition geometry are generally more consequential than a conventional low-speed bypass-only layout. This page consolidates the manufacturer and distributor product information into an engineering summary covering the 2:1 multiplexing function, 200 MHz output capability, package constraints, replacement considerations, and practical PCB guidance. It also distinguishes the exact ICS557G-08 ordering code from other family suffixes and the earlier 8-pin SOIC device so procurement and redesign decisions use the correct footprint.

Запрос цены Контакты
ICS557M-01 - 100MHz PCIe Clock Source | Renesas Electronics
ICS557M-01

ICS557M-01 - 100MHz PCIe Clock Source | Renesas Electronics

Renesas Electronics ICS557M-01 is a PCI Express clock and frequency generator integrated circuit with PLL-based clocking, a 100 MHz differential output, and HCSL/LVDS-compatible signaling. It is designed to provide the reference clock required by PCI Express cards and related high-speed digital systems. The device uses a clock or crystal input and produces a pair of differential outputs, allowing it to support common PCIe clock-source architectures while reducing the number of separate timing components required on the board. The ICS557M-01 is an application-specific clock generator rather than a general-purpose microcontroller or power-management device. In the broader semiconductor hierarchy, it belongs to the clock and timing IC category, where PLL-based frequency generation is used to create stable, phase-aligned clock signals for high-speed interfaces. Its primary design function is to convert a reference clock or crystal into the differential 100 MHz clock used by PCI Express equipment. Key characteristics include one clock-generation circuit, PLL support, clock or crystal input, HCSL and LVDS differential outputs, and a 1:1 input-to-output ratio according to the manufacturer-related product listings. The device is offered in an 8-pin SOIC package, making it suitable for compact PCI Express card designs where component count and board area are important. Differential output architecture helps preserve signal integrity across controlled-impedance PCB traces. The ICS557M-01 is appropriate for PCI Express endpoint cards, add-in cards, embedded PCIe equipment, test systems, and industrial or communication equipment that requires a dedicated reference-clock source. It can simplify clock distribution by providing two differential outputs from one timing circuit. The exact electrical limits, operating-temperature range, output amplitude, jitter, and power-supply requirements should be confirmed against the current manufacturer datasheet before production release. Layout quality is critical in any high-speed clock circuit. Place the device close to the clock-consuming circuitry, use controlled-impedance routing for differential pairs, keep the return path continuous, and minimize stubs and unnecessary vias. Decoupling capacitors should be positioned close to the supply pins according to the datasheet guidance. This page combines the device’s documented PCI Express purpose, package information, interface characteristics, sourcing guidance, and engineering-oriented design notes to support component selection and board-level implementation.

Запрос цены Контакты
ICS558G-01 - 250 MHz 2:4 CMOS Clock Buffer | Renesas
ICS558G-01

ICS558G-01 - 250 MHz 2:4 CMOS Clock Buffer | Renesas

The Renesas ICS558G-01 is a 2:4 fanout clock buffer that distributes a high-speed clock to four low-skew CMOS outputs. The device accepts either CMOS or PECL input, operates from a 2.375 V to 5.5 V supply, and supports frequencies up to 250 MHz. It is packaged in a 16-pin TSSOP measuring 0.173 inch, or 4.40 mm, in width. A clock fanout buffer, also called a clock distribution buffer, is a clock and timing IC that receives one clock signal and reproduces it across multiple outputs. It belongs to the clock buffer and driver family within the broader clock and timing IC category. Clock buffers isolate the source from downstream loading, provide multiple usable clock destinations, and can reduce the timing disturbance that would otherwise appear when several circuits were connected directly to one clock source. The ICS558G-01 provides four CMOS outputs with three-state capability, allowing one, three, or all four outputs to be disabled independently through the output-enable controls. Its input stage supports CMOS and PECL signaling, giving it utility in systems that translate or distribute clocks between different logic families. The 250 MHz maximum operating frequency places it in applications such as telecommunications, networking equipment, industrial control, and general-purpose digital logic. Renesas describes the ICS558-01 as a TO CMOS clock driver with an integrated divide-by-4 function and four low-skew outputs. The divide capability allows the device to support clock distribution arrangements where a divided reference is needed in addition to distributed outputs. The configurable output-enable inputs add bus-management flexibility, particularly in test systems and backplane systems where clock outputs must be parked while a channel is inactive. Typical uses include switching and routing fabrics in telecommunications equipment, parallel clock distribution in network interfaces, synchronization in industrial controllers, and clock generation stages in test and measurement instruments. The device is also suitable for backplane applications because its three-state outputs can be disabled when a module is not selected, reducing contention and unwanted clock activity. The principal design consideration is signal integrity. Because the ICS558G-01 is intended for high-speed distribution, trace length matching, controlled impedance routing, and short output stub lengths help preserve edge quality and maintain usable skew. Decoupling should be placed close to the supply pins, and unused outputs should be disabled rather than left permanently enabled if downstream channels are not required. This page combines the principal electrical specifications, interface details, application guidance, design notes, and verified sourcing information for the ICS558G-01. It also provides a framework for evaluating compatible replacements without changing the 16-TSSOP board footprint or the 2:4 clock-distribution function.

Запрос цены Контакты
ICS570A - 170MHz Zero Delay Buffer | Renesas | Clocking
ICS570A

ICS570A - 170MHz Zero Delay Buffer | Renesas | Clocking

The Renesas Electronics ICS570A is a multiplier and zero-delay buffer clock IC designed for 5 V systems, with a maximum output clock frequency of 170 MHz and an 8-pin SOIC package. It combines clock multiplication, fanout distribution, and zero-delay buffering in one device, making it suitable for systems that need multiple related clock outputs without adding substantial propagation delay. According to the manufacturer datasheet information, the A version is intended for 5 V designs and the B version is intended for 3.3 V designs. A zero-delay buffer is a clock-integrity device that reproduces an input clock at one or more outputs while compensating for internal propagation delay through a phase-locked-loop technique. ICS570A uses Integrated Circuit Systems proprietary analog/digital PLL techniques, allowing the device to provide low input-to-output skew while distributing or multiplying the source clock. The part is therefore positioned between a clock source and the digital circuits, processors, or memory that require synchronized clock signals. Key documented features include support for 14 multiplier choices from 0.5x to 32x, output clock frequency up to 170 MHz at 5 V, and the ability to recover degraded input clock duty cycle. The listed low input-to-output skew is 300 ps maximum for outputs above 60 MHz. The device is also identified as functionally equivalent to the AV9170, although the manufacturer explicitly notes that the AV9170 is not a pin-for-pin replacement. Typical uses include processor and controller clock generation, communication-system clock distribution, memory clocking, retrofit or modernization of older clock architectures, and any board requiring a multiplied or buffered reference clock. The ICS570A should be selected when the surrounding circuit requires a 5 V zero-delay buffer and an 8-pin SOIC footprint. The B version or another device should be considered when the system operates from 3.3 V, because the A and B versions target different supply voltages. Designers should preserve the manufacturer's recommended input, output, termination, and load conditions. Clock jitter and skew tables depend on the termination resistance and load capacitance, so a replacement must be checked against the original clock topology rather than selected only by package. This page combines the verified manufacturer and distributor information with a conservative drop-in assessment, clearly separating confirmed replacements from parts that are only functionally equivalent.

Запрос цены Контакты
ICS570AI - 170MHz Clock Generator | Renesas Electronics
ICS570AI

ICS570AI - 170MHz Clock Generator | Renesas Electronics

The Renesas Electronics ICS570AI is a 170 MHz fanout-distribution, spread-spectrum clock generator and zero-delay buffer built with analog/digital phase-locked-loop techniques. It operates from a 4.75 V to 5.25 V supply and is packaged in an 8-SOIC surface-mount package measuring 0.154 inch, or 3.90 mm, in width. The device combines clock generation, multiplication, zero-delay buffering, fanout distribution, and spread-spectrum operation in one clock-management circuit. A clock generator is an integrated circuit that establishes a stable reference frequency and distributes clock signals to digital logic. A zero-delay buffer preserves clock-edge relationships while compensating for propagation delays introduced by PCB traces and interconnects. The ICS570AI belongs to the ClockBlocks family and integrates an analog/digital PLL with a zero-delay-buffer function, placing it within the broader hierarchy of clock and timing ICs, clock generators, and semiconductor timing devices. The primary features include operation up to 170 MHz, four-clock fanout distribution, spread-spectrum clock generation, zero-delay buffering, and multiplier functionality. Spread-spectrum operation reduces energy concentrated at a single frequency, which can reduce narrowband emissions and improve electromagnetic-compatibility behavior in systems that need controlled clock spreading. Fanout allows multiple destinations to receive related clock signals from one source while maintaining consistent phase relationships. Technically, the device uses proprietary analog/digital PLL techniques to multiply or generate the required output frequency and to compensate for clock-path delay. This architecture is intended for high-speed systems in which several digital subsystems must operate from a common timing reference. The A-version is identified for 5 V designs, while the device family also includes a 3.3 V B-version; therefore, supply voltage must be checked carefully when comparing family members or considering a replacement. Typical applications include high-speed data-transfer equipment, memory interfaces, communications equipment, network-processing systems, server and storage platforms, and clock-distribution trees for FPGA-based or ASIC-based designs. The 170 MHz rating makes the device relevant to legacy and established digital platforms that need a compact, integrated alternative to discrete oscillators, dividers, and multiple buffer stages. PCB implementation should prioritize short clock routes, continuous return paths, and symmetrical fanout geometry. Place decoupling capacitors close to the supply and ground pins, and avoid routing sensitive clock nets beneath noisy switching components. Because spread-spectrum settings and PLL loop behavior affect system timing, validate output jitter, skew, rise time, and EMI at the intended operating frequency before production release. This product page organizes the verified operating limits, package information, sourcing guidance, engineering applications, replacement constraints, and design checks for the ICS570AI. It also distinguishes documented electrical facts from parameters that require confirmation against the manufacturer datasheet or system measurements, helping engineers make a technically defensible design decision.

Запрос цены Контакты
ICS570AIT - 170MHz Zero-Delay Clock Buffer | Renesas
ICS570AIT

ICS570AIT - 170MHz Zero-Delay Clock Buffer | Renesas

Renesas ICS570AIT is a 170 MHz PLL-based zero-delay buffer (ZDB) and fanout clock distributor packaged in an 8-pin SOIC. The A-version is intended for 5 V designs, providing four non-inverted CMOS clock outputs with low-delay clock distribution and programmable spread-spectrum operation. Its clock-buffer architecture integrates analog and digital phase-locked-loop techniques to synchronize multiple system clock domains. A zero-delay buffer is a clock-management IC that reproduces an input clock at its outputs while compensating for internal propagation delay through a phase-locked loop. Positioned within the hierarchy of clock and timing ICs, a ZDB complements ordinary clock buffers by allowing a system to obtain several low-skew copies of a reference clock. Fanout distribution expands one source into multiple synchronized loads for processors, memory interfaces, communications equipment, and embedded control systems. The ICS570AIT supports clock frequencies up to 170 MHz and includes spread-spectrum clock generation for reducing narrowband EMI emissions in sensitive equipment. Its four CMOS outputs provide one-to-four fanout capability, while the PLL-based zero-delay architecture supports predictable clock relationships between distributed loads. The 8-pin SOIC package measures approximately 3.90 mm in width and accepts a 0.154-inch lead pitch. The A-version supply recommendation distinguishes ICS570AIT from the 3.3 V B-version. Designers must therefore verify supply rails, input levels, output loading, and downstream input thresholds before applying the device. Because the part distributes rather than originates the reference clock, input slew rate, return path, and output termination remain important aspects of the implementation. Typical applications include processor and memory clock distribution, communications-interface clock fanout, embedded system clock trees, and EMI-sensitive digital equipment. Spread-spectrum operation is particularly relevant when the reference clock feeds high-speed digital circuitry and reduced spectral concentration is desirable without eliminating the fundamental clock. For reliable implementation, use the pin-description table and typical application circuit in the manufacturer datasheet when assigning PCB tracks. Keep the reference clock and output routes short, provide a continuous return plane, and validate timing at the actual device pins because package and trace delay can affect a nominal zero-delay design. This product reference combines the device architecture, operating limits, package information, sourcing guidance, and design considerations needed to evaluate the ICS570AIT. It also distinguishes verified drop-in alternatives from related clock devices that require different voltage, pinout, output-count, or circuit arrangements.

Запрос цены Контакты
ICS570AT - 170MHz Spread Spectrum Clock | Renesas
ICS570AT

ICS570AT - 170MHz Spread Spectrum Clock | Renesas

The Renesas Electronics ICS570AT is a 170 MHz fanout-distribution clock generator and zero-delay buffer (ZDB) integrated into a 8-SOIC package. It combines a clock-generation function with fanout distribution and zero-delay buffering, allowing a system to multiply, distribute, and buffer a reference clock while controlling the relationship between input and output edges. The device is identified as a spread-spectrum clock generator for applications where controlled clock-spectrum spreading can reduce narrowband emissions. A zero-delay buffer is an integrated timing device that compensates for the propagation delay introduced by clock fanout networks. By placing the buffer close to the load or in the fanout path, the device helps preserve edge alignment between clock outputs. The ICS570AT integrates this clock-distribution role with analog/digital phase-locked-loop technology, a technique also used in multiplier-based clocking solutions. The principal documented characteristics of the ICS570AT are its 170 MHz operating class, spread-spectrum clock-generator function, zero-delay-buffer function, fanout-distribution capability, and 8-SOIC surface-mount package. These characteristics place it in the clock and timing hierarchy between a single reference oscillator and the multiple clock domains required by processors, converters, transceivers, and memory interfaces. The ICS570AT is useful when a board requires more than a passive clock fanout buffer. Passive fanout devices introduce insertion delay and may not compensate for load-dependent skew, while the integrated PLL-based architecture in the ICS570AT is intended to regenerate and distribute a clock with phase adjustment. The spread-spectrum feature adds another design tool for systems where reducing concentrated spectral peaks is a priority. Typical uses include audio and network interface clocking, digital signal processing subsystems, data-conversion equipment, communications modules, and industrial control boards. In these systems, the device can drive downstream clock-consuming circuits from a shared reference while keeping clock edges aligned across multiple branches. When laying out a design around the ICS570AT, follow the pin-description table and recommended decoupling network in the Renesas 570 datasheet. Keep the clock output traces short, use controlled-impedance routing, and avoid placing noisy switching nodes beneath the device. Confirm the selected spread-spectrum profile, output count, and timing budget against the system requirement before releasing the layout. This page combines the manufacturer datasheet information with package-level guidance, application context, comparison parameters, and practical layout considerations. It is intended to help engineers evaluate the ICS570AT as a drop-in clock-distribution choice and to identify the checks required before substituting another PLL or zero-delay-buffer device.

Запрос цены Контакты
ICS570B - 170 MHz 3.3 V PLL Clock Buffer | Renesas
ICS570B

ICS570B - 170 MHz 3.3 V PLL Clock Buffer | Renesas

The Renesas Electronics ICS570B is a 3.3 V fanout distribution, spread-spectrum clock generator and zero-delay buffer (ZDB) that provides a maximum output clock frequency of 170 MHz in an 8-pin SOIC package. It combines a proprietary analog/digital phase-locked loop with clock multiplication, fanout, duty-cycle correction and low-skew output buffering for systems that require multiple related clocks. A zero-delay buffer is a clock-integrity device that uses phase-locked-loop techniques to reproduce an input clock at its outputs with very small propagation delay relative to the source clock. It belongs to the clock and timing hierarchy of clock generators, PLL multipliers, fanout buffers, clock drivers and zero-delay buffers. The ICS570B is intended for systems where several logic domains require related clocks without introducing significant inter-clock skew. The ICS570B supports output clock frequencies up to 170 MHz at 3.3 V and can select between 14 multiplication ratios from 0.5x to 32x. It also includes fanout distribution, spread-spectrum clock generation and the ability to recover a degraded input-clock duty cycle. The maximum input-to-output skew is 300 ps for output rates above 60 MHz, making it useful for high-speed communications, storage, networking and processor clock trees. Internally, the device uses analog/digital PLL techniques rather than a simple static clock buffer. This architecture allows one reference clock to be multiplied and distributed while limiting output-to-output skew. The published family information also identifies the B version as the 3.3 V option and the A version as the 5 V option, making supply-voltage compatibility a critical selection criterion when comparing family members. Typical uses include frequency multiplication for a CPU or bus clock, fanout to multiple peripheral clock domains, spread-spectrum clock generation for reducing electromagnetic interference, and duty-cycle restoration of a degraded source clock. The 8-pin SOIC package supports conventional surface-mount assembly and keeps the footprint compact for clock-distribution sections on communication, industrial and computing boards. Designers should verify the input and output reference clock requirements, the selected multiplication ratio, output termination and load capacitance against the Renesas 570 datasheet before layout. Keep clock traces short and match trace lengths where output-to-output skew is critical. Provide a continuous ground reference under the device and place decoupling capacitors close to the supply pins. This page consolidates verified manufacturer and distributor information, published price references, family-level drop-in options and practical clock-tree design guidance. It also identifies where application-specific data, such as exact supply current, temperature range and production lifecycle status, must be confirmed against current manufacturer documentation.

Запрос цены Контакты
ICS570BI - 170MHz 3.3V Zero Delay Buffer | Renesas
ICS570BI

ICS570BI - 170MHz 3.3V Zero Delay Buffer | Renesas

Renesas Electronics ICS570BI is a 170 MHz fanout-distribution, spread-spectrum clock generator and zero-delay buffer built around analog/digital phase-locked-loop techniques. The B-version is intended for 3.3 V designs and is supplied in an 8-pin SOIC package measuring approximately 3.90 mm in width. Its zero-delay-buffer architecture distributes a clock signal while compensating for propagation delay through the PLL-based clock path. A zero-delay buffer is a clock-management semiconductor that reproduces an input clock at one or more outputs with very low transfer delay. It belongs to the clock buffer hierarchy, where it sits between a clock source and digital logic requiring multiple synchronized copies. Unlike a basic logic buffer, the ICS570BI combines an analog/digital PLL with fanout and spread-spectrum clock functions, placing it within the broader clock and timing IC category. The principal operating characteristics visible in the product documentation include a maximum clock frequency of 170 MHz, one fanout output, a 3.3 V B-version supply target, spread-spectrum clock generation, zero-delay operation, and an 8-pin SOIC package. The spread-spectrum function is useful when reducing concentrated clock energy on a narrow frequency band, while the fanout output provides a local clock for digital circuitry. The single-output arrangement favors designs that need one precisely distributed clock rather than several independent destinations. Renesas describes the ICS570 as a performance upgrade within the IDT ClockBlocks family, using proprietary analog/digital PLL techniques. This architecture is intended to support higher-speed and lower-voltage systems while maintaining a clock distribution function. The B version is specifically recommended for 3.3 V designs, while the A version is associated with 5 V designs; substituting those versions requires a complete power and timing review rather than simple interchangeability. Typical uses include processor-clock distribution, communications equipment, data-conversion systems, digital control boards, and other synchronous electronics requiring a low-delay clock source. In these applications, the device can reduce the load presented to an upstream oscillator or clock controller while delivering a clean local copy to a receiving circuit. Spread-spectrum operation can also assist systems that need to reduce narrowband clock peaks, although exact spread-spectrum range and configuration details must be confirmed from the manufacturer datasheet. The primary design consideration is power-domain compatibility: the ICS570BI is the 3.3 V version and must not be treated as an automatic substitute for a 5 V ICS570 variant. Board designers should also preserve the bypass-capacitor and layout guidance in the manufacturer datasheet because PLL-based clock devices can be sensitive to return-current paths and supply-noise coupling. A solid ground plane and short supply connections help isolate the clock output from switching noise. This product page combines the manufacturer function description with the exact package and operating identifiers, then adds application guidance, comparison fields, and practical design considerations. It is intended to help engineers identify the correct 3.3 V zero-delay buffer, locate the authoritative datasheet, assess replacement constraints, and plan a clock-distribution layout before committing the footprint to production hardware.

Запрос цены Контакты
ICS570BIT - 170MHz Spread Spectrum Clock Buffer | Renesas
ICS570BIT

ICS570BIT - 170MHz Spread Spectrum Clock Buffer | Renesas

The Renesas Electronics ICS570BIT is a fanout distribution, spread-spectrum clock generator and zero-delay buffer operating up to 170 MHz in an 8-SOIC surface-mount package. It provides a 1:2 fanout ratio and a 3.15 V to 3.45 V supply range. The ICS570BIT uses proprietary analog/digital phase-locked-loop techniques to distribute a clock while reducing electromagnetic emissions through spread-spectrum operation. Its zero-delay-buffer architecture helps preserve edge timing between a source clock and the driven output clocks. A zero-delay buffer is a clock-integrity device that reproduces a clock at its outputs with very little propagation delay while compensating for loading and skew. The ICS570 belongs to the Renesas ClockBlocks family and combines clock generation, fanout distribution, and zero-delay buffering in one integrated circuit. This integration can reduce the number of separate timing components required in systems that need multiple related clock outputs. The principal operating characteristics include a maximum clock frequency of 170 MHz, a 1:2 output ratio, and a 3.15 V to 3.45 V operating voltage range. The device is identified as a fanout distribution, spread-spectrum clock generator, and zero-delay buffer. Its 8-SOIC package provides a compact surface-mount solution for clock-generation, communications, industrial-control, and embedded systems. The spread-spectrum function is useful when reducing the spectral concentration of a clock signal. By varying the clock frequency over a controlled range, the device can reduce narrowband emissions and improve system-level electromagnetic compatibility. The PLL-based architecture is intended to provide clock distribution while maintaining predictable output relationships for downstream digital circuitry. Typical applications include clock fanout for communications equipment, local clock distribution in industrial systems, clock generation for embedded processors, and EMI-sensitive digital platforms. The ICS570BIT is especially relevant when a design requires two outputs, a maximum operating frequency of 170 MHz, and 3.3 V-class operation. Its integrated functions help simplify clock trees while preserving controlled edge relationships. When designing around the ICS570BIT, verify the input and output timing requirements, supply-voltage tolerance, and the number of loads connected to each output. Keep clock traces short and use controlled-impedance routing where signal-integrity requirements are demanding. This page combines the manufacturer documentation, distributor listing information, package details, and engineering-oriented selection guidance for the ICS570BIT.

Запрос цены Контакты
ICS570BT - 170MHz Zero-Delay Clock Buffer | Renesas
ICS570BT

ICS570BT - 170MHz Zero-Delay Clock Buffer | Renesas

The Renesas Electronics ICS570BT is a fanout distribution, spread-spectrum clock generator and zero-delay buffer with a maximum operating frequency of 170 MHz and one clock output. The device is packaged in an 8-pin SOIC measuring 3.90 mm wide and uses proprietary analog/digital phase-locked-loop techniques to provide low-skew clock distribution. It is categorized as a clock generator, PLL, and frequency synthesizer within integrated clock and timing circuitry. A zero-delay buffer is a clock-distribution component that reproduces an input clock at its outputs while compensating for internal propagation delay. By combining a phase-locked loop with buffer functions, the ICS570BT can support multiple logic domains that require closely related clock signals. The fanout configuration permits one input clock to be distributed to one output, while the spread-spectrum capability can reduce electromagnetic emissions in systems where controlled clock spectral shaping is useful. The ICS570BT's key documented characteristics include a 170 MHz maximum frequency and an 8-SOIC package. Its zero-delay-buffer architecture uses proprietary analog/digital PLL techniques to control phase and timing relationships. The device is intended for synchronizing outputs in personal computers, data communications, graphics, and video systems, and its off-chip feedback paths can allow system-level timing loops to eliminate delay through other devices. The device combines frequency multiplication and zero-delay buffering in one timing IC. This integration can reduce the number of separate clock-handling components required in a board design. The fanout architecture is particularly useful when a single high-speed reference must feed downstream digital logic, while the spread-spectrum feature provides an additional method for controlling spectral content. Designers should still evaluate loop stability, output jitter, skew, and power-supply requirements against the exact operating conditions of the target system. Typical applications include personal-computer clock synchronization, data-communication equipment, graphics systems, video infrastructure, and other high-speed digital platforms. In these systems, the ICS570BT can provide a common clock reference while maintaining timing alignment among multiple output domains. Its 170 MHz ceiling makes it suitable for systems whose functional clock rates remain below that limit, including communications interfaces, processor support circuits, and clock-distribution networks. When designing around the ICS570BT, preserve the recommended input, output, and decoupling connections in the manufacturer application guidance. Keep high-speed traces short, use a controlled reference plane, and place support components close to their associated pins. Because the part combines PLL and buffer functions, validate startup, feedback configuration, output phase, and system-level skew across voltage and temperature rather than assuming ideal zero-delay behavior. This product page consolidates the verified 170 MHz frequency, one-output fanout architecture, 8-SOIC package, zero-delay-buffer function, spread-spectrum capability, sourcing links, and practical selection guidance. It also distinguishes documented facts from specifications that must be confirmed in the manufacturer datasheet before schematic release, timing validation, or production procurement.

Запрос цены Контакты
ICS571M - 160MHz Zero Delay Buffer | Renesas Electronics
ICS571M

ICS571M - 160MHz Zero Delay Buffer | Renesas Electronics

Renesas Electronics ICS571M is a 160 MHz fanout distribution zero-delay buffer IC packaged in an 8-pin SOIC measuring 3.90 mm wide. It is designed for clock distribution applications where a source signal must be reproduced across multiple destinations while minimizing propagation delay. The verified distributor listing identifies the device as a one-output fanout buffer with zero-delay characteristics. A zero-delay buffer belongs to the clock and timing IC hierarchy. Unlike a conventional logic buffer, which introduces a specified propagation delay, this device uses an internal buffer arrangement intended to preserve clock-edge timing between the driving source and distributed loads. Fanout buffers are used to reduce loading on a clock generator, isolate multiple destinations, and provide a repeatable distribution point on clock, data, or control networks. The principal verified characteristics are a maximum clock frequency of 160 MHz, one fanout output, and an 8-SOIC surface-mount package with a stated width of 3.90 mm. The distributor data also classifies ICS571M under Clock Generators, PLLs, and Frequency Synthesizers, reflecting its primary use within clock and timing systems. Detailed supply-voltage, output-impedance, skew, jitter, and temperature limits were not present in the supplied verified records. ICS571M is suited to communication equipment, processor clock networks, data converters, instrumentation, and industrial electronics requiring local clock distribution. Its small SOIC outline supports compact designs, while the zero-delay architecture can be preferable when an upstream source must drive several clocked loads without intentionally adding another propagation-delay stage. Designers should verify input slew rate, output loading, supply voltage, and timing margins against the manufacturer datasheet before release. Decoupling and return-path planning remain important because a clock buffer can reproduce upstream supply noise and edge distortion at every distributed output. PCB length matching may also be required in systems with stringent setup-and-hold limits. This product record consolidates verified distributor specifications, sourcing links, practical application guidance, and honest data-gap disclosures. It also distinguishes confirmed parameters from values that require datasheet review, helping engineers make a technically defensible selection without treating unverified electrical limits as guaranteed specifications.

Запрос цены Контакты
ICS571MT - 160MHz 1:2 Zero Delay Buffer | Renesas Electronics
ICS571MT

ICS571MT - 160MHz 1:2 Zero Delay Buffer | Renesas Electronics

Renesas Electronics ICS571MT is a high-speed, low-phase-noise zero delay buffer (ZDB) designed to distribute one CMOS clock input to two true CMOS outputs. It operates up to 160 MHz, supports a 1:2 input-to-output ratio, and is packaged in an 8-pin SOIC measuring approximately 3.90 mm wide. The part integrates analog and digital phase adjustment to minimize clock skew and preserve low-noise timing performance. A zero delay buffer is a clock-management IC that uses a phase-adjustable buffer architecture to compensate for propagation delay introduced by clock distribution networks. Within the broader hierarchy, it is a fanout buffer, then a clock buffer, then a clock and timing IC, and finally a semiconductor. By placing a ZDB close to a clock-consuming circuit, designers can reduce the timing penalty associated with board traces, while a 1:2 ratio allows one source clock to feed two independent loads. Key characteristics include a maximum frequency of 160 MHz, CMOS inputs, CMOS outputs, PLL capability, one input circuit, two true outputs, and an input-to-output ratio of 1:2. The ICS571MT can also operate as a low-phase-noise frequency multiplier according to the manufacturer description. Its low-skew outputs are useful when related clocks must remain closely aligned, and phase noise better than -100 dBc/Hz is described from 10 kHz to 1 MHz offset from the carrier under the cited operating conditions. The typical application is clock fanout in telecommunications, networking, industrial control, test and measurement, and digital processing systems. It can distribute a common clock to two domains, provide clock buffering between a source and a load, or provide two low-skew copies of a reference signal. The 8-pin SOIC package supports conventional surface-mount assembly and is easier to handle than a fine-pitch BGA package. Designers should maintain short, impedance-controlled clock traces, use a ground reference close to the device, and verify source and load termination against the clock edge rate. A nominal maximum frequency does not guarantee acceptable timing margin in every board environment; rise time, loading, return paths, and available setup and hold time must be evaluated together. This page combines the manufacturer-described operating characteristics, packaging information, application guidance, and verified drop-in candidates to support faster component evaluation and board-level sourcing decisions.

Запрос цены Контакты
ICS574M - 160MHz 1:4 PLL Zero-Delay Buffer | Renesas
ICS574M

ICS574M - 160MHz 1:4 PLL Zero-Delay Buffer | Renesas

Renesas Electronics ICS574M is a PLL-based 1:4 fanout and zero-delay buffer rated up to 160 MHz, with CMOS inputs and CMOS clock outputs in an 8-SOIC surface-mount package. The device contains one clock circuit, uses a 1:4 input-to-output ratio, and provides four low-skew outputs for high-speed clock-distribution systems. Its operating-temperature range is 0°C to 70°C, and supplier records identify the part as obsolete or end-of-life. A zero-delay buffer is a clock and timing IC that combines a phase-locked loop with multiple output stages. Within the product hierarchy, it belongs to clock distribution devices, which are part of clock and timing integrated circuits and ultimately semiconductor signal-management components. By compensating for internal propagation delay while distributing one source clock across four outputs, this type of device helps maintain controlled timing relationships across multiple digital loads. The primary characteristics of the ICS574M are its 160 MHz maximum operating frequency, 1:4 input-to-output fanout, CMOS logic compatibility, and PLL-based zero-delay operation. Four independently available clock outputs make the device suitable where one incoming reference must drive several clock domains while limiting output-to-output timing skew. The 8-SOIC package provides a compact surface-mount format with a stated body width of 3.90 mm and lead pitch of 0.154 inches. Technically, the PLL-based architecture is intended to reduce propagation delay and skew across distributed outputs. The verified device information identifies the input and output technology as CMOS and confirms that PLL operation is supported. Detailed electrical limits, supply-voltage operating range, output-to-output skew, input-to-output delay, operating-current consumption, and timing tolerances are not available in the supplied source data and therefore require confirmation against the original manufacturer datasheet before release to production. Typical uses include processor and peripheral clock distribution, data-processing systems, communications equipment, test systems, and other high-speed digital platforms requiring one reference clock to feed four destinations. Because the ICS574M is listed as obsolete, engineers should confirm the available lifecycle status, remaining supply, and any formal last-time-buy or end-of-life schedule with the authorized distributor. The primary design consideration is timing closure. Board traces must be length- and impedance-matched when the four outputs must arrive at their destinations within a tightly controlled interval. Decoupling, grounding, and output loading should follow the original datasheet guidance, while any substitute must be checked for pin assignment, supply voltage, frequency ceiling, skew, and output enable behavior rather than package name alone. This product record combines verified distributor specifications, lifecycle evidence, package information, and practical replacement guidance. It distinguishes documented electrical facts from unavailable parameters, helping engineers identify whether the original ICS574M remains suitable or whether a redesign is required.

Запрос цены Контакты
ICS574MI - 160 MHz PLL Zero-Delay Fanout Buffer | Renesas
ICS574MI

ICS574MI - 160 MHz PLL Zero-Delay Fanout Buffer | Renesas

The Renesas Electronics ICS574MI is a PLL-based zero-delay fanout buffer designed for high-speed clock distribution, operating up to 160 MHz and providing four low-skew CMOS outputs from one clock input. The device is packaged in an 8-SOIC and is identified as a 1:4 fanout, zero-delay buffer with an integrated PLL. Its primary role is to align a distributed clock with the source clock while compensating for propagation delay introduced by board traces, connectors, and loading. A zero-delay buffer is a clock-and-timing integrated circuit that uses phase-locked-loop technology to reproduce an input clock at its outputs with nearly zero net propagation delay. It belongs to the fanout-buffer hierarchy within clock and timing ICs, where PLL-based devices trade additional internal complexity for improved edge alignment and predictable output skew. This makes the ICS574MI suitable for systems in which several circuits must receive a related clock without accumulating cumulative trace-delay differences. According to the Renesas 574 Datasheet, the ICS574 is based on proprietary low-jitter PLL techniques. The documented operating point includes speeds up to 160 MHz at 3.3 V, with four low-skew outputs. When one output is returned directly to the FBIN input, the rising edge of each output can be aligned with the rising edge of the feedback signal, allowing the feedback path to compensate for clock distribution delay around the board. Typical uses include processor and FPGA clock distribution, memory-interface clock fanout, backplane clock replication, communications equipment, and test-and-measurement systems. The 1:4 ratio reduces the number of separate clock-driver channels required when four destinations need a common timing reference. Because a fanout buffer does not regenerate data content, its outputs are intended for clock or low-fanout control signals rather than high-speed data traffic. The key design consideration is output loading and board topology. Short, matched traces, terminated clock networks, and appropriate supply decoupling help preserve edge quality and limit skew. When cascading multiple fanout devices, engineers should verify cumulative jitter, output-to-output skew, duty-cycle distortion, and loading with the complete clock distribution network rather than relying on individual device specifications.

Запрос цены Контакты
ICS574MIT - 160MHz 1:4 Zero-Delay Buffer | Renesas
ICS574MIT

ICS574MIT - 160MHz 1:4 Zero-Delay Buffer | Renesas

The Renesas Electronics ICS574MIT is a PLL-based zero-delay fanout buffer operating up to 160 MHz, with a 1:4 input-to-output ratio and four low-skew CMOS outputs in an 8-pin SOIC package. It is designed for high-speed systems requiring closely aligned clock signals and negligible propagation delay. A zero-delay buffer is a clock-distribution device that uses phase-locked-loop technology to compensate for internal and board propagation delay. In the clock and timing hierarchy, the ICS574MIT belongs to the fanout-buffer class, where a single periodic input is reproduced across multiple outputs with tightly controlled skew. This makes it useful when several sequential logic sections must receive a common clock without accumulating separate distribution delays. The ICS574MIT provides a maximum operating frequency of 160 MHz, four outputs, and a 1:4 fanout ratio. Its CMOS input and output interface operates from a 3.3 V supply. Connecting one output directly to the FBIN feedback input aligns the rising edge of each output with the rising edge of the feedback signal, supporting deterministic clock relationships across the distributed network. Internally, the device uses proprietary low-jitter PLL techniques to generate four low-skew outputs. This architecture is intended for high-speed processor, memory, networking, and communications systems where clock skew can limit setup and hold timing margin. Its single-input, four-output organization reduces the number of separate buffers required when several destination devices must operate from the same source clock. Typical uses include memory clock distribution, network-interface clock fanout, high-speed digital backplanes, processor clock routing, and communication equipment. The device is particularly useful where the source clock must reach multiple endpoints while maintaining a controlled relationship between output edges. The compact 8-pin SOIC package also supports conventional surface-mount PCB assembly. For implementation, reserve the feedback path as a short, controlled connection from one clock output to FBIN, and observe the maximum operating frequency, supply-voltage, and output-loading limits in the manufacturer datasheet. Confirm the pin assignment and input/output timing relationship against the selected package suffix before releasing a PCB layout. This product reference combines the Renesas manufacturer description, distributor specifications, package information, operating characteristics, and practical replacement guidance. It also identifies where a drop-in substitute cannot be established without additional manufacturer timing data, preventing a package-compatible candidate from being presented incorrectly as a production replacement.

Запрос цены Контакты
ICS574MT - 160 MHz PLL Zero-Delay Fanout Buffer | Renesas
ICS574MT

ICS574MT - 160 MHz PLL Zero-Delay Fanout Buffer | Renesas

The Renesas Electronics ICS574MT is a PLL-based zero-delay fanout buffer for high-speed digital systems, operating up to 160 MHz with four low-skew outputs and a 1:4 input-to-output ratio. It is housed in an 8-SOIC package and is intended for clock distribution, memory interfacing, and other high-speed applications requiring closely aligned output edges. The device uses CMOS input and output signals and is based on IDT's proprietary low-jitter phase-locked-loop techniques. One output can be fed back to the FBIN input to align rising output edges with the input clock. ICS574MT is the tube-packaging ordering code for the 8-SOIC device; other order codes can represent different temperature or shipping configurations. A zero-delay buffer is a clock-distribution integrated circuit that compensates for clock-propagation delay between a source and multiple destinations. PLL-based implementations use a phase-locked loop to create an internal clock relationship that allows the outputs to track the input edge while adding little nominal propagation delay. In the broader IC hierarchy, ICS574MT belongs to the clock and timing IC family, combining clock generation, phase control, and multi-output distribution functions in one package. The principal features of ICS574MT include a maximum operating frequency of 160 MHz, four CMOS outputs, and a 1:4 fanout ratio. The PLL architecture is intended to minimize output-to-output skew, while low jitter helps preserve timing margin in high-speed systems. Its single-circuit organization and compact 8-SOIC package make it suitable for compact systems that need several synchronized clock copies without implementing a discrete oscillator or multi-stage buffer tree. Typical uses include processor and FPGA clock distribution, memory clock fanout, high-speed interface clocking, data-converter sampling systems, and communications equipment. The feedback connection can be used when the application requires the output rising edges to be aligned with the reference input. Because the device is intended for high-speed digital operation, board-level trace matching, controlled impedance, adequate decoupling, and careful handling of clock return paths are important for maintaining signal integrity. Designers should compare the complete datasheet limits for supply voltage, input and output thresholds, output drive, propagation delay, jitter, skew, temperature range, and package tolerances before finalizing a circuit. The ICS574MT is most appropriate when a PLL-based four-output zero-delay buffer is needed and the board can provide a clean, continuous clock reference. Request current availability and sourcing details through the Request a Quote form on this page.

Запрос цены Контакты
ICS580M-01 270MHz 2:2 Clock Multiplexer | Renesas Electronics
ICS580M-01

ICS580M-01 270MHz 2:2 Clock Multiplexer | Renesas Electronics

Renesas Electronics ICS580M-01 is a 2:2 zero-delay clock multiplexer and buffer designed for glitch-free switching between two clock sources. It supports clock frequencies up to 270 MHz, operates from a 2.5 V to 5.5 V supply, and is packaged in a 16-SOIC configuration measuring 0.154 inches, or 3.90 mm, in width. The device provides two clock outputs and a control input for selecting the active clock path. A clock multiplexer is a timing-device category used to route one of two clock signals toward a downstream circuit while minimizing switching disturbances. This device combines clock selection with zero-delay buffer behavior, making it useful where a system must change clock sources without producing the short pulses or unwanted transitions that can disrupt digital logic, serializers, processors, and communication equipment. The main operating characteristics are a maximum clock frequency of 270 MHz, a 2.5 V to 5.5 V supply-voltage range, and a 16-SOIC package. The 2:2 arrangement allows one selected clock to be distributed to two outputs, reducing the need for separate buffer devices when the same selected clock must reach more than one destination. ICS580M-01 is intended for clock-distribution, clock-switching, and digital-system applications where clean transitions and controlled source selection are important. The zero-delay-buffer function is particularly relevant in systems where the multiplexer must present a predictable clock relationship to downstream circuitry. The exact input and output timing behavior should be confirmed from the manufacturer datasheet before using the device in a new design. A typical implementation places the device between two candidate clock sources and the logic that requires a stable clock. The select control is driven by the system controller, while the two outputs are connected to the appropriate destination circuits. Designers should account for supply decoupling, controlled select transitions, trace impedance, and the relationship between the selected clock and surrounding circuitry. For new layouts, place the device close to the clock source and the load being switched, route clock traces as controlled-impedance transmission lines where required, and keep the select control away from sensitive clock nodes. Verify the device’s operating limits, pin functions, and timing requirements in the manufacturer datasheet before production release. This product page combines the manufacturer-aligned specifications, package information, sourcing structure, application guidance, and drop-in comparison information for ICS580M-01. It is intended to help engineers assess clock-multiplexer functionality and PCB reuse before completing a production design.

Запрос цены Контакты