Товары (44.000+)

ISL8394IBZ - 4-Channel SPDT Analog Switch | Renesas Electronics
ISL8394IBZ

ISL8394IBZ - 4-Channel SPDT Analog Switch | Renesas Electronics

The Renesas Electronics ISL8394IBZ is a precision quad SPDT analog switch designed for low-voltage, single-supply or dual-supply signal-routing systems. It provides four independently controlled switches, a 2:1 multiplexing configuration, 35 ohm on-resistance in the manufacturer listing, and a 20-pin SOIC package. The device is intended for applications requiring low power consumption, low leakage current, and fast switching performance. An analog switch is a semiconductor interface that routes analog or digital signals between circuit nodes under digital control. The ISL8394 belongs to the broader analog switch and multiplexer hierarchy, which includes SPDT switches, multiplexers, demultiplexers, and interface ICs used in test, measurement, communications, and instrumentation systems. Its quad SPDT arrangement allows one source signal to be connected to either of two destinations for each channel, or two sources to be routed to a common output, depending on the application configuration. According to the manufacturer datasheet, the ISL8394 operates from a single +2 V to +12 V supply or from a dual supply of +/−2 V to +/−6 V. The device is specified for low power consumption of 5 microwatts, maximum leakage current of 2.5 nA, and fast switching speeds. The supplied product information identifies the device as a 4-circuit, 2:1 analog switch with 35 ohm on-resistance in a 20-SOIC package. These characteristics suit battery-powered equipment and precision measurement circuits where signal integrity and low standby current are important. Typical uses include battery-powered test equipment, data-acquisition systems, audio and communication signal routing, instrumentation interfaces, and compact embedded measurement products. In a two-channel routing arrangement, control logic can select one of two analog inputs for connection to a shared signal-processing block while the other inputs remain electrically isolated. Designers should pay close attention to the control logic levels, supply sequencing, input voltage range, and signal amplitude at each switched node. The low-leakage and low-power characteristics make the ISL8394 useful in battery-powered systems, but the PCB should minimize parasitic capacitance around high-impedance nodes and provide clean return paths for control and supply pins. This page combines the manufacturer datasheet details, distributor identification, package information, and practical design guidance to support component selection, replacement planning, and PCB implementation. It also distinguishes the core ISL8394 function from nearby comparator and multiplexer families, helping engineers determine when the quad SPDT architecture is the correct switching choice.

Запрос цены Контакты
ISL84051IB - 8:1 100Ω Analog Multiplexer | Renesas
ISL84051IB

ISL84051IB - 8:1 100Ω Analog Multiplexer | Renesas

The Renesas Electronics ISL84051IB is a low-voltage analog multiplexer with an 8:1 configuration, 100 ohm on-resistance, and a 16-pin SOIC package. It operates from a single +2 V to +12 V supply or from dual supplies, allowing it to support both low-voltage portable systems and conventional positive and negative analog rails. The device provides TTL and CMOS-compatible control inputs and an inhibit function for opening all signal paths. An analog multiplexer is an interface IC that connects one of several input channels to a shared output path. It belongs to the broader analog switch and signal-routing hierarchy, which sits within interface semiconductors and embedded control systems. Multiplexers reduce the number of physical connections required by sensors, test equipment, data acquisition systems, and communication equipment while allowing one converter or processor input to monitor multiple signals. The ISL84051IB's principal benefits include its 8:1 channel ratio, maximum on-resistance of 100 ohm at ±5 V, low-voltage operation, and pin compatibility with established multiplexers. The inhibit pin simplifies system control because all signal paths can be disconnected simultaneously. TTL and CMOS-compatible address and select inputs also support a broad range of digital control circuits without requiring elevated input levels. Internally, the device uses controlled analog switches to route one selected input to the common output. Its on-resistance matching between channels keeps similar resistance characteristics across the selected paths, helping preserve signal amplitude consistency. Because it is a passive switch rather than an active amplifier, it introduces insertion loss determined principally by on-resistance and does not provide gain or level shifting. Typical applications include battery-powered instrumentation, automated test equipment, data acquisition, communication routing, sample-and-hold systems, and microcontroller-based sensor interfaces. The low +2 V minimum supply is useful for portable equipment, while dual-supply operation is valuable when signals can be bipolar. The 16-pin SOIC package also supports conventional surface-mount assembly and board-level manual inspection. Designers should verify signal amplitude, bandwidth, injection charge, off leakage, and the complete logic truth table against the manufacturer datasheet. Keep high-impedance routing paths short, provide a stable ground reference, and account for the resistance of PCB traces when precision measurements depend on total path resistance. This page combines the manufacturer device description with a focused engineering comparison, replacement guidance, pin-level sourcing information, and practical application guidance for engineers evaluating the ISL84051IB in multiplexed analog signal paths.

Запрос цены Контакты
ISL84052IA - Dual 4:1 Analog Multiplexer | Renesas
ISL84052IA

ISL84052IA - Dual 4:1 Analog Multiplexer | Renesas

The Renesas ISL84052IA is a low-voltage analog multiplexer containing two independent 4:1 single-pole, double-throw switches, with the device presented in a 16-pin QSOP package. It supports single-supply operation from 2 V to 12 V and dual-supply operation from 0.3 V to 15 V, according to the Intersil datasheet and Renesas product page. Its typical on-resistance is 100 ohms, while the maximum on-resistance is 225 ohms with a positive 5 V supply. These specifications make it suitable for routing low-frequency analog signals in test, measurement, communication, and instrumentation systems. An analog multiplexer is an interface IC that connects multiple signal paths to a shared output through controlled switches. The ISL84052IA belongs to the analog switch and multiplexer hierarchy, within interface ICs and discrete semiconductor switching systems. Its dual 4:1 organization allows two independent channels to be selected by digital control logic, reducing the number of external routing components in systems with multiple sensors, test points, or measurement channels. The low-voltage capability also supports modern mixed-signal equipment operating from reduced supply rails. Key electrical features include 100-ohm on-resistance, 225-ohm maximum on-resistance at a positive 5 V supply, less than 6-ohm on-resistance matching between channels, and 2 pC charge injection. The device is described as having low-voltage, single and dual supply operation, TTL/CMOS-compatible inputs, and a maximum signal current rating of 30 mA. The Renesas product page identifies compatibility with MAX4051, MAX4052, MAX4053, MAX4581, MAX4582, MAX4583, 74HC4051, 74HC4052, and 74HC4053 families. The two independent switches make the ISL84052IA useful in instrumentation where several inputs must be routed to separate measurement channels. It can also be used in battery-powered test equipment, signal-conditioning boards, automated test equipment, and communication interfaces where supply voltage and board area are constrained. The digital select inputs allow the multiplexing function to be coordinated by a microcontroller or system logic. The main design consideration is ensuring that the selected signal amplitude, supply polarity, and control levels remain within the device's operating limits. Input and output filtering may be needed when switch transitions produce transient charge injection. The QSOP package also requires adequate spacing between adjacent high-impedance nodes to reduce leakage and coupling. For replacement decisions, compare the exact pin arrangement and supply configuration rather than relying only on the multiplexer description. This page combines the manufacturer product-page characteristics, datasheet parameters, package information, application guidance, and drop-in comparison considerations for engineers evaluating the ISL84052IA. It provides practical selection context beyond a basic distributor listing.

Запрос цены Контакты
ISL84467IRTZ - Quad SPDT Analog Switch, 0.39Ω rON, 1.65-4.5V | Renesas
ISL84467IRTZ

ISL84467IRTZ - Quad SPDT Analog Switch, 0.39Ω rON, 1.65-4.5V | Renesas

The Renesas (formerly Intersil) ISL84467IRTZ is an ultra-low ON-resistance, low-voltage, bidirectional Quad SPDT (Dual DPDT) analog switch housed in a 16-pin TQFN (3x3 mm) package. The device operates from a single +1.65V to +4.5V supply, delivers a typical ON resistance of 0.39Ω, and supports switching speeds of tON = 33ns and tOFF = 16ns. The 1.8V logic-compatible digital inputs allow direct interfacing with modern low-voltage microcontrollers without level shifters, making the part attractive for portable and battery-powered designs where both signal integrity and low quiescent drain matter. An analog switch (also called an analog multiplexer or bilateral switch) is a solid-state device that uses MOSFET transistors to route analog or digital signals between input and output pins under digital control. Quad SPDT (Single Pole Double Throw) means the device contains four independent 2:1 switches, each capable of selecting between two signal paths. Compared to electromechanical relays, analog switches offer far faster switching, no contact bounce, lower power, and indefinite mechanical life, but they have limited voltage handling and finite OFF isolation. Key features of the ISL84467IRTZ include 0.39Ω typical rON (which minimizes signal attenuation and distortion for low-level audio or precision analog signals), 1.8V logic-compatible inputs across the full supply range, break-before-make switching action to prevent momentary shorts between adjacent channels, and ESD protection on the logic and signal pins. The bidirectional signal path means each switch can carry signals in either direction with identical AC performance, simplifying PCB routing when source and destination roles are not predetermined. The four SPDT switches are organized as two DPDT (Double Pole Double Throw) pairs that switch in tandem, useful for differential signal routing in audio, USB, or data-acquisition front ends. The TQFN-16 package with an exposed pad provides low thermal resistance and a small 3x3 mm footprint, suitable for high-density handheld equipment. Targeted applications per the manufacturer datasheet include battery-powered portable instruments, audio/video signal routing, mobile handsets, and handheld test equipment. When designing with the ISL84467IRTZ, observe the absolute maximum signal voltage (typically equal to V+ plus ESD diode drops) and place decoupling capacitors close to the V+ pin. For low-distortion audio applications, the low rON and low charge injection of this switch help preserve signal fidelity; designers should still account for switch capacitance in bandwidth-limited paths. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты
ISL84516IB - Low-Voltage Dual-Supply SPST Switch | Renesas
ISL84516IB

ISL84516IB - Low-Voltage Dual-Supply SPST Switch | Renesas

The Renesas ISL84516IB is a low-voltage, dual-supply, single-pole single-throw analog switch with a 1:1 signal configuration, 20 ohm on-resistance and an 8-SOIC package. It is designed to operate from positive and negative supplies spanning ±1.5 V to ±6 V, making it suitable for precision analog signal-routing systems operating from low-voltage battery rails. Its stated low power consumption of 350 mW supports energy-conscious portable equipment. An analog switch is a semiconductor device that routes signals between circuit nodes under digital control. The SPST designation identifies one independently selectable path, while the 1:1 configuration indicates a single signal path for each switch function. Within the broader hierarchy, the ISL84516IB is an analog switch, a discrete analog interface function, and ultimately an integrated circuit used for signal routing rather than voltage conversion. The key benefits of the ISL84516IB include dual-supply operation from ±1.5 V to ±6 V, a specified 20 ohm on-resistance and low power consumption of 350 mW. The device family is described as a precision analog switch with excellent on-resistance flatness, making it useful when the resistance contribution of the switch must remain relatively consistent across the selected signal range. Low leakage current is another stated family characteristic relevant to battery-powered and high-impedance circuits. The ISL84516IB belongs to the ISL84516 and ISL84517 precision analog-switch family. The ISL84516 variant provides a 1:1 switching arrangement, while the companion ISL84517 provides a different switch arrangement within the same low-voltage, dual-supply family. The IB ordering designation identifies the specific catalog configuration offered in the 8-SOIC package. Because this part operates from bipolar rails, its application circuitry must keep every driven terminal within the permitted supply range. Typical applications include battery-powered portable instruments, low-voltage data-acquisition systems, precision analog test equipment and small-signal routing networks. The device can be paired with an ISL84516IB or ISL84517-family member where separate routing paths or complementary switching functions are required. Its low-voltage range is especially relevant to systems powered from single-cell lithium-ion batteries and rail-to-rail signal chains. The primary design consideration is ensuring that the switch-control logic and analog signal amplitudes remain compatible with the dual supply rails. Layout should minimize parasitic capacitance around the signal pins and keep return-current paths short. Designers should also verify the on-resistance contribution against the source and destination input impedances before using the switch in precision attenuation or measurement paths. This page combines the device's catalog identity, operating limits, package information and application guidance with practical routing considerations. It also identifies the limitation of the available substitution information: confirmed pin-to-pin alternatives require verification against the Renesas pin description and electrical characteristics before they can be treated as drop-in replacements.

Запрос цены Контакты
ISL84521IB - 100Ω Quad SPST Analog Switch | Renesas
ISL84521IB

ISL84521IB - 100Ω Quad SPST Analog Switch | Renesas

The Renesas Electronics ISL84521IB is a low-voltage CMOS analog switch IC containing four independently controlled single-pole single-throw switches, with a maximum on-resistance of 100Ω and operation from single or dual supplies. The device is offered in a 16-pin SOIC package and is designed for low-power signal-routing applications. An analog switch is an integrated interface circuit that connects or disconnects a signal path under digital control. A single-pole single-throw switch provides one independently selectable route, while a quad analog switch combines four such switches in one IC. The ISL84521 belongs to the analog-switch, interface-IC, and semiconductor hierarchy and can serve as a low-voltage multiplexing or sampling element in test, measurement, communication, and industrial control systems. Key features include four separately controlled SPST switches, a 100Ω maximum on-resistance, channel matching of 1Ω, 1µW low power consumption, and 10nA maximum leakage current at 85°C. Switching timing is specified as 45ns typical turn-on and 15ns typical turn-off, while break-before-make operation helps prevent undesirable current paths during transitions. The ISL84521 supports single-supply operation from 3V to 12V and dual-supply operation from ±3V to ±6V. Its CMOS implementation supports TTL-compatible control inputs and low power consumption. Four independent controls allow separate signals to be routed without requiring multiple single-switch packages, reducing board area in multi-channel analog systems. Typical uses include battery-powered test equipment, programmable signal conditioning, communication-interface routing, industrial control modules, and precision measurement systems. The low 15ns typical turn-off time is useful when the application requires rapid isolation or discharge paths, while the 100Ω maximum on-resistance should be considered in high-impedance analog nodes. For layout, place each switched signal trace close to its assigned switch pin and keep control traces away from sensitive analog paths. Confirm input and output voltage limits against the selected supply configuration. Account for the 100Ω maximum channel resistance, 1Ω matching specification, and leakage when calculating circuit errors. This page combines manufacturer specifications, package details, application guidance, and a focused replacement analysis. It also identifies the limits of drop-in substitution by separating same-footprint options from parts requiring a different package, helping engineers shorten sourcing and design-review time.

Запрос цены Контакты
ISL84523IV - 4-Channel SPST Analog Switch | Renesas Electronics
ISL84523IV

ISL84523IV - 4-Channel SPST Analog Switch | Renesas Electronics

Renesas Electronics ISL84523IV is a low-voltage CMOS quad analog switch with four independently controlled SPST channels, 100 ohm maximum on-resistance, and a 16-pin TSSOP package. It operates from a single +2 V to +12 V supply or from a split ±2 V to ±6 V supply, making it suitable for low-voltage signal routing in battery-powered and precision test systems. An analog switch is a semiconductor interface device that connects or isolates analog signals under digital control. Its function in the broader hierarchy is analog switch → multiplexer or demultiplexer → interface IC. The ISL84523IV uses four separate SPST paths rather than a shared multiplexer bus, allowing four signals to be routed independently while keeping the control logic separate from the analog nodes. Key characteristics include a maximum on-resistance of 100 ohm, on-resistance matching between channels of 1 ohm, low power consumption below 1 microwatt, and maximum leakage current of 1 nA in the principal operating description. Switching times are listed as 45 ns on and 15 ns off. The manufacturer also identifies TTL and CMOS control compatibility, a minimum 2000 V ESD protection rating using Method 3015.7, and break-before-make timing of at least 2000 ns. The ISL84523IV family is designed for precision low-voltage signal switching. Separate control inputs permit each SPST switch to be commanded independently, while low leakage and low power consumption help preserve small signals in battery-operated measurement equipment. Its stated pin compatibility with DG411, DG412, and DG413 devices supports reuse of existing routed analog-switch layouts when control behavior and application requirements are compatible. Typical uses include battery-powered test equipment, automated measurement systems, signal-isolation networks, sample-and-hold circuitry, and low-voltage analog front ends. The device is also identified as a drop-in replacement for MAX4521, MAX4522, and MAX4523 devices. Because it supports both single-supply and dual-supply operation, it can address dual-rail instrumentation as well as systems whose analog signals remain above ground. For new layouts, route each analog switch terminal to the intended signal path and keep control traces away from sensitive analog nodes. Confirm the complete pin map and control truth table in the manufacturer datasheet before making substitutions. The 16-pin TSSOP footprint supports compact density, but exposed copper and careful grounding remain important for preserving low-level signal integrity. This page combines the manufacturer’s electrical and switching characteristics with practical routing guidance, drop-in cross-reference options, and a parameter-by-package comparison. It is intended to help engineers identify whether the ISL84523IV fits the required voltage range, control interface, switching behavior, and board footprint before requesting a quote.

Запрос цены Контакты
ISL84541IB - Dual SPST Analog Switch, 2.7-12V | Renesas
ISL84541IB

ISL84541IB - Dual SPST Analog Switch, 2.7-12V | Renesas

Renesas ISL84541IB is a precision dual analog switch built as two independent SPST circuits in an 8-SOIC package. The device operates from a single +2.7 V to +12 V supply, offers a typical on resistance of 30 Ω, and supports both normally open and normally closed signal paths. Its 35 ns typical turn-on time, 25 ns typical turn-off time, and maximum 5 pC charge injection make it suitable for low-voltage analog routing. An analog switch is a semiconductor interface device that connects or disconnects signals under digital control while preserving the analog signal rather than converting it to a digital representation. The ISL84541 belongs to the analog-switch hierarchy within interface ICs and is controlled by CMOS-compatible logic inputs. It is intended to route low-voltage signals while limiting insertion loss, switching transients, and power consumption in portable and precision equipment. Key characteristics include low power consumption below 5 µW, leakage current down to 100 pA maximum, and on-resistance matching between channels below 1 Ω. The manufacturer identifies the device as fully specified at 3.3 V and 5 V supplies. These attributes are valuable in battery-powered equipment, where both leakage and switching charge influence battery life, and in measurement paths where predictable channel resistance is important. The ISL84541 uses complementary SPST switches to provide independent routing in both directions. Its low charge injection limits the voltage disturbance created when control inputs change state, while fast switching reduces control-to-signal delay. The single-supply architecture simplifies system power design, and the low-leakage implementation helps preserve high-impedance sensor and sampling nodes between switch transitions. Typical uses include mobile-device signal routing, battery-powered instruments, audio and communication interfaces, test and measurement systems, and low-voltage analog acquisition circuits. Renesas also identifies the ISL84541 as a drop-in replacement for selected MAX4541-series and DG9461/DG9262-series devices, providing a practical basis for second-source and legacy-design migration. Designers should account for the external drive and ground relationship of the logic inputs, preserve the specified supply range, and connect unused control inputs to a defined logic level. Signal-path layout should minimize parasitic capacitance because switch transitions can inject charge into high-impedance nodes. PCB signal integrity should also be checked across the complete voltage and frequency range used by the selected analog source. This page combines the manufacturer function description, exact device identifiers, drop-in cross references, and practical application guidance to support component selection and PCB-level replacement decisions without relying on generic analog-switch descriptions.

Запрос цены Контакты
ISL84541IU - Dual SPST 12V 60Ω Analog Switch | Renesas
ISL84541IU

ISL84541IU - Dual SPST 12V 60Ω Analog Switch | Renesas

The Renesas Electronics ISL84541IU is a dual SPST analog switch designed for low-voltage, single-supply operation. The device provides two independently controlled analog switches, a 60 Ω on-resistance specification, and an operating supply range of +2.7 V to +12 V in an 8-MSOP package. It is suited to battery-powered and portable equipment where signal routing must remain compatible with low supply voltages. An analog switch is a semiconductor device that connects or disconnects analog signal paths under digital control. The ISL84541 family belongs to the analog switch and multiplexer hierarchy, which sits within interface ICs and broader signal-conditioning systems. Unlike a mechanical relay, an analog switch changes electrical connections much faster and can route low-level signals without physically moving conductive contacts. The ISL84541IU combines this switching function with low-power operation and supply flexibility. Key family features include on-resistance matching below 1 Ω between channels, maximum charge injection of 5 pC, power consumption below 5 µW, and maximum leakage current of 10 nA at 85°C. The devices are fully characterized at 3.3 V and 5 V supplies, which makes their behavior predictable in common portable and embedded rails. A Pb-free option is also available within the ISL84541 family. The dual-SPST configuration gives each switch one normally closed and one normally closed terminal pair in its SPDT implementation, allowing a signal to be routed to or away from the common terminal. The low charge injection helps limit transient disturbances when the control state changes, while matched on-resistance helps reduce gain or timing differences between channels. These characteristics are important when the same source feeds multiple downstream paths. Typical uses include battery-powered test equipment, portable measurement systems, audio and communication-signal routing, automated test equipment, and low-voltage data-acquisition equipment. The +2.7 V minimum supply supports systems powered from two alkaline cells, while the +12 V maximum provides additional range for industrial and instrumentation designs. The 8-MSOP package also supports compact board layouts when adequate assembly and inspection controls are used. A primary design consideration is ensuring that the control voltage and analog signal levels remain within the device's operating limits. Place bypass capacitance close to the supply pin, keep switched traces short, and route sensitive inputs away from switching-control and clock traces. Also verify the switch configuration in the pin-description table before assigning PCB nets, because the family includes several SPST and SPDT arrangements. This product page combines the exact ISL84541IU catalog attributes with family-level technical information, drop-in compatibility findings, and practical guidance for low-voltage analog routing. It is intended to help engineers compare the device against documented equivalents, plan PCB changes, and select an appropriate replacement without conflating packaging suffixes with electrically distinct alternatives.

Запрос цены Контакты
ISL84543CB - Dual SPST Analog Switch, 60 Ohm, 8-SOIC | Renesas
ISL84543CB

ISL84543CB - Dual SPST Analog Switch, 60 Ohm, 8-SOIC | Renesas

Renesas Electronics ISL84543CB is a dual, single-pole single-throw analog switch with a 1:1 signal configuration, 60 ohm on-resistance, and an 8-pin SOIC package. Designed for single-supply operation, the device accepts a +2.7 V to +12 V supply and is characterized at 3.3 V and 5 V, making it suitable for low-voltage analog routing in battery-powered and portable equipment. An analog switch is a semiconductor interface that connects or disconnects signal paths under digital control. The ISL84543CB belongs to the analog-switch hierarchy, where a multiplexer or demultiplexer is used to route signals among multiple endpoints. Its dual SPST architecture provides two independently controlled switching functions, allowing analog, test, measurement, or peripheral signals to be selected without duplicating surrounding circuitry. The family is specified for low-voltage, single-supply operation. A 60 ohm on-resistance provides a defined path impedance for many low-frequency and moderate-impedance analog circuits, while the dual-channel construction supports compact signal routing. Operation is also identified at 3.3 V and 5 V supply levels, covering common consumer, industrial, communication, and portable-system rails. The ISL84543CB is intended to add routing capability to systems with limited analog inputs or general-purpose I/O. Its two switch sections can be used independently, and the device is associated with drop-in replacements for MAX4541, MAX4544, and DG9263. These cross-references are important when maintaining an existing 8-SOIC layout or reducing design changes during component sourcing. Typical uses include battery-powered test equipment, analog measurement systems, peripheral selection, signal isolation, and compact embedded interfaces. Because the device operates from a single supply, it can simplify rails in portable systems where generating additional bipolar or split-supply voltages would be undesirable. When designing around the ISL84543CB, account for the 60 ohm path resistance and control-logic levels when interpreting signal attenuation, settling behavior, and logic compatibility. Keep routing traces short, provide a low-impedance supply connection near the device, and verify the control inputs against the voltage levels produced by the host microcontroller. Use the manufacturer pin-description table when assigning PCB tracks. This product page consolidates the exact ordering information, verified technical characteristics, documented cross-references, and practical design guidance for engineers evaluating the ISL84543CB in compact, single-supply analog-routing designs.

Запрос цены Контакты
ISL84543IB - Dual 60 Ohm Analog Switch | Renesas Electronics
ISL84543IB

ISL84543IB - Dual 60 Ohm Analog Switch | Renesas Electronics

The Renesas Electronics ISL84543IB is a dual 1:1 analog switch with 60 ohm on-resistance, operating from a single 2.7 V to 12 V supply in an 8-pin SOIC package. The device supports 25 ns and 35 ns switching-time specifications, has 13 pF signal capacitance, and operates across a -40 °C to +85 °C temperature range. Two independently controlled SPST paths provide flexible analog routing for test, measurement, communication, and signal-conditioning systems. An analog switch is a semiconductor interface that routes electrical signals between internal nodes without amplifying or converting them. The ISL84543IB belongs to the analog switch and multiplexer hierarchy, where each switch path connects or isolates a signal under digital control. Its low on-resistance minimizes signal attenuation, while its fast switching operation supports time-domain and communication equipment in which control latency affects system performance. The principal benefits of the ISL84543IB are its 60 ohm on-resistance, 25 ns and 35 ns switching specifications, and operation across a broad 2.7 V to 12 V supply range. The low switching resistance is especially useful when routing sensor, test, or low-level analog signals. The dual 1:1 configuration allows two signals to be switched independently, making the device suitable for scan paths, signal-isolation circuits, configurable analog front ends, and resource-limited embedded systems. The 8-SOIC package provides a compact surface-mount implementation with exposed external leads and standard production-board handling. Because the device uses a single positive supply, its control circuitry and analog signal paths can operate without a negative supply rail. Designers should account for input-voltage limits, control-logic levels, off-state leakage, signal capacitance, and the effect of the switch resistance when calculating gain, settling time, and usable bandwidth. Typical applications include automated test equipment, oscilloscope and measurement front ends, communications routing, analog signal conditioning, battery-powered instruments, and embedded control systems. Two channels in one package reduce board area compared with separate single-switch implementations. The device is particularly useful when a system must route two analog signals with separate control commands while retaining low switching resistance and short switching times. A practical design consideration is to keep analog traces short and provide a solid ground reference beneath or near the switching network. Control traces should be driven with compatible logic levels, and unused control or signal pins should be connected according to the Renesas datasheet. Check the complete electrical limits and recommended operating conditions before using the switch outside its characterized supply range. This page combines the manufacturer-specific ISL84543IB electrical characteristics with pin-compatible replacement information, application guidance, and engineering-focused design notes. It supports faster part selection while keeping replacement decisions centered on package compatibility, signal integrity, timing, and operating conditions.

Запрос цены Контакты
ISL84544CB - Dual SPST 60Ω Analog Switch | Renesas
ISL84544CB

ISL84544CB - Dual SPST 60Ω Analog Switch | Renesas

The Renesas Electronics ISL84544CB is a precision dual analog switch configured as a 2:1 multiplexer, with a listed on-resistance of 60 ohm and an 8-pin SOIC package. It operates from a single +2.7 V to +12 V supply, making it suitable for low-voltage signal routing in battery-powered, industrial, communications, and test equipment. The switch combines fast transition times, low charge injection, and low leakage in a compact surface-mount package. An analog switch is an electrically controlled semiconductor that connects or disconnects analog signal paths while preserving the selected voltage. The ISL84544CB belongs to the analog switch and multiplexer hierarchy within interface ICs and semiconductor signal-routing systems. Its single-supply operation supports both 3.3 V and 5 V equipment, while its dual SPST arrangement can form a 2:1 analog multiplexer for selecting between two signal sources. According to the Renesas product information, key advantages include fully specified operation at 3.3 V and 5 V, on-resistance matching between channels below 1 ohm, maximum charge injection of 5 pC, and power consumption below 5 microwatts. Switching times are listed as 35 ns for turn-on and 25 ns for turn-off. The device also provides guaranteed break-before-make behavior and minimum 2,000 V ESD protection, which are important for preventing momentary input overlap. The ISL84544 family is designed for precision, low-voltage analog routing. Its low power dissipation reduces loading in portable systems, and its low charge injection limits command-induced voltage disturbances in measurement and signal-conditioning circuits. The matching between channel on-resistances is particularly useful when both selected paths must present similar impedance to a following amplifier, ADC, or sensor interface. Typical applications include battery-powered instrumentation, data-acquisition front ends, test and measurement equipment, communications interfaces, and precision sensor multiplexing. The dual SPST topology is particularly useful when two inputs must share one downstream converter or amplifier. It can also be used for sample-and-hold or signal-isolation functions when the control timing and break-before-make requirement are properly observed. Designers should account for input and output signal amplitudes, control-logic levels, switch on-resistance, and off leakage when defining the system bandwidth. Keep sensitive routing paths short, use a defined control state during power transitions, and verify that the 2:1 configuration matches the intended schematic rather than assuming a conventional dual-SPDT pinout. The manufacturer datasheet pin-description table should be used for final PCB routing and logic assignment. This product page combines the Renesas family specifications with package-level selection guidance, same-footprint alternatives, parameter comparisons, and practical implementation notes. These resources help engineers distinguish drop-in options from functionally similar devices and identify the electrical conditions that determine whether the ISL84544CB is suitable for a specific analog-routing design.

Запрос цены Контакты
ISL84544CP - 30Ω Dual SPDT Analog Switch | Renesas
ISL84544CP

ISL84544CP - 30Ω Dual SPDT Analog Switch | Renesas

The Renesas Electronics ISL84544CP is a low-voltage, single-supply dual SPDT analog switch with a maximum on-resistance of 30 Ω, on-resistance matching below 1 Ω, and maximum charge injection of 5 pC. The device operates from a single +2.7 V to +12 V supply and is packaged in an 8-pin PDIP. It is designed for low-voltage signal routing where low power consumption, fast switching, and low leakage are important. An analog switch is an analog interface IC that connects or disconnects circuit nodes under digital control. The ISL84544CP belongs to the SPDT analog-switch family, within analog switches, interface ICs, and broader semiconductor signal-routing systems. Its SPDT configuration provides a common terminal that can select either of two switched terminals, allowing one source signal to be routed to one of two destinations. Key features include a maximum on-resistance of 30 Ω, less than 1 Ω matching between channels, and charge injection of no more than 5 pC. The device specifies turn-on and turn-off times of 35 ns and 25 ns, respectively. Its low power consumption is below 5 µW, while maximum leakage current at 85 °C is 10 nA, making it suitable for battery-powered and portable equipment. The ISL84544CP is manufactured for operation from a +2.7 V to +12 V supply and includes break-before-make switching behavior. Guaranteed minimum 2000 V ESD protection helps the interface withstand electrostatic discharge during handling. The family is also identified as a drop-in replacement for MAX4544 devices and is pin compatible with MAX323, subject to verifying the electrical limits of the specific replacement. Typical uses include battery-powered instruments, audio and video signal routing, communication equipment, test and measurement systems, and heads-up-display interfaces. Because the on-resistance introduces insertion loss and the control signals interface with lower-voltage logic, the supply voltage, logic levels, signal range, and required bandwidth should be checked together before implementation. For robust layouts, route each switched trace away from high-impedance amplifier inputs and keep the common node connections short. Place bypass capacitance close to the supply pin, use a defined logic return, and account for charge injection when the switched signal changes state. The 8-pin PDIP format favors through-hole prototype and industrial assembly rather than compact surface-mount designs. This product page combines the manufacturer's functional and switching specifications with package guidance, application analysis, verified drop-in relationship information, and a parameter-level comparison. These practical details help engineers evaluate signal-integrity, routing, and supply compatibility before modifying an existing design.

Запрос цены Контакты
ISL84544IB - Dual SPDT Analog Switch, 2.7-12V | Renesas
ISL84544IB

ISL84544IB - Dual SPDT Analog Switch, 2.7-12V | Renesas

The Renesas Electronics ISL84544IB is a precision dual SPDT analog switch designed for single-supply operation from +2.7V to +12V. The device provides a 60 ohm on-resistance, 35 ns ton, 25 ns toff, and 5 pC maximum charge injection, and is housed in an 8-pin SOIC package. Its low-leakage and low-power characteristics make it appropriate for battery-powered, portable, communication, test, and signal-routing equipment. An analog switch is a semiconductor device that routes signals between external circuit nodes under digital control. The SPDT configuration connects one common terminal to one of two switched terminals at a time. The ISL84544 contains two independent SPDT channels, allowing paired signal paths to be selected by control logic. In the broader hierarchy, it is an interface IC, also described as an analog switch, multiplexer, or signal-routing IC. The ISL84544 series emphasizes low power consumption below 5 microwatts and low leakage current, with a stated maximum of 100 pA under the cited conditions. Switch timing reaches 35 ns ton and 25 ns toff, while guaranteed break-before-make behavior prevents two switched terminals from momentarily connecting together. These characteristics help preserve signal integrity when the device selects sources, routes test signals, or controls analog paths in compact systems. The family supports low-voltage single-supply operation and provides on-resistance matching between channels below 1 ohm. Renesas specifically identifies pin-compatible replacements for MAX4544 devices and pin compatibility with MAX323 devices. A 2000V minimum ESD rating adds handling protection for portable and communication equipment, although correct system-level grounding and signal-chain design remain essential. Typical uses include battery-powered test equipment, handheld instruments, communication systems, audio and video signal routing, and heads-up displays. The switch can isolate a common node from one of two sources or route a signal toward a downstream converter. Its 8-pin SOIC format supports conventional surface-mount assembly, while dual-channel control makes it practical for paired analog paths. When laying out a circuit, place control traces away from sensitive analog inputs and keep switch-node routing short to minimize parasitic capacitance and pickup. Confirm that signal amplitudes remain within the permitted analog-switch limits and check the break-before-make interval against downstream timing requirements. The production package variant and industrial-grade ordering code should be confirmed before release.

Запрос цены Контакты
ISL84684IR - Dual 2:1 Analog Switch, 500mOhm | Renesas
ISL84684IR

ISL84684IR - Dual 2:1 Analog Switch, 500mOhm | Renesas

The Renesas Electronics ISL84684IR is a dual 2:1 analog switch with 500mOhm on-resistance, low 27ns switching performance, and a 10-pin TDFN package measuring 3 x 3 mm. The device provides two independent SPDT switch circuits for routing low-voltage analog or digital signals, combining compact area with fast operation for signal-control and multiplexing requirements. An analog switch is an interface IC that connects or disconnects signal paths under digital control. In the broader semiconductor hierarchy, it belongs to the switch and multiplexer family within interface ICs. Each SPDT circuit can route one common terminal to one of two switched terminals, allowing a controller to select among sensors, amplifiers, filters, converters, or other signal sources without changing the external board layout. The ISL84684IR combines a 500mOhm on-resistance with 27ns switching time, helping preserve signal integrity when the switched nodes operate at moderate or low frequencies. Its 50ns break time supports fast control transitions. The 4nA leakage specification is particularly relevant to high-impedance analog nodes, where leakage can create offset errors, unwanted loading, or errors in downstream measurement circuits. The device uses a 10-TDFN surface-mount package with dimensions of 3 x 3 mm. Its compact footprint is useful in portable instruments, test systems, communication equipment, and mixed-signal products where routing density matters. The dual-circuit configuration also lets one package control two related switch paths, reducing component count compared with separate single switches where board area is constrained. Typical applications include audio path routing, sensor selection, test-and-measurement signal control, communications equipment, and industrial interface modules. Two switch sections can be used for complementary routing, isolation between functional blocks, or redundant paths. Designers should still verify signal levels, control-logic compatibility, leakage effects, and switching transients against the application’s operating conditions. The principal design consideration is ensuring that the driven signal remains within the switch’s electrical limits while control transitions do not inject unacceptable disturbance into sensitive downstream circuitry. Keep routing short, use a stable ground reference, and place appropriate bypass capacitance near the supply pins. Confirm the complete pin configuration and exposed-pad connection directly from the manufacturer datasheet before fabrication. This page combines package, switching, leakage, sourcing, pinout-location, drop-in replacement, and application guidance for engineers evaluating the ISL84684IR. It also identifies the confirmed same-package alternatives and highlights the trade-offs involved when changing vendors or selecting related switch configurations.

Запрос цены Контакты
ISL84762IR - 600mOhm Dual SPDT Analog Switch | Renesas
ISL84762IR

ISL84762IR - 600mOhm Dual SPDT Analog Switch | Renesas

The Renesas Electronics ISL84762IR is a dual SPDT analog switch with a 600 mOhm on-resistance, housed in a 10-terminal TDFN surface-mount package measuring 3 x 3 mm. The device provides two independent 2:1 analog-switch circuits, making it suitable for routing low-voltage analog signals in compact industrial and embedded systems. Its single-supply architecture, ultra-low on-resistance design, and 10-terminal HVSON-style package are the principal headline characteristics. An analog switch is an integrated semiconductor that routes signals between circuit paths under digital control. The SPDT, or single-pole double-throw, topology connects one common terminal to one of two selectable terminals. A dual SPDT switch contains two such networks, allowing one component to control two independent signal paths. Within the broader interface-IC hierarchy, analog switches sit between sensors, test equipment, communication circuitry, and mixed-signal processors. The ISL84762IR combines a 600 mOhm on-resistance with a low-voltage, single-supply design. Its 2:1 configuration supports two separately switched channels, while the 10-TDFN (3 x 3 mm) package limits board area in space-constrained equipment. The surface-mount construction and square HVSON package code suit automated assembly. The manufacturer datasheet should be consulted for logic levels, voltage limits, channel resistance matching, leakage, and switching-time details before final circuit selection. Internally, the device uses active transistor switching networks to control analog-signal paths while control inputs determine the selected branch. Because switch performance depends on voltage, current, and logic thresholds, the external system must maintain the supply and control-input conditions specified by the manufacturer. The package's exposed thermal and electrical construction also requires attention to PCB layout, grounding, and the datasheet land pattern to achieve predictable behavior. Typical uses include signal multiplexing in measurement systems, routing between analog sensors and processing circuitry, portable test equipment, communication interfaces, and industrial control modules. The dual-channel organization can reduce the number of discrete routing components when a board must select two signals independently. It is especially useful when board area is more constrained than the number of available control pins. The primary design consideration is preserving signal integrity around the switched nodes. Route sensitive analog traces away from high-current switching paths, use the manufacturer's reference land pattern, and connect decoupling and return paths consistently. Before production release, confirm the exact supply range, control logic, maximum switched voltage, and electrical limits against the current Renesas datasheet. This page combines the exact ISL84762IR configuration with application guidance, verified drop-in references, package information, and practical PCB considerations. It is designed to help engineers determine whether the dual SPDT topology, 600 mOhm on-resistance, and compact 3 x 3 mm footprint satisfy the routing and board-space requirements of a new design.

Запрос цены Контакты
ISL84762IU - 600mOhm Dual SPDT Analog Switch | Renesas
ISL84762IU

ISL84762IU - 600mOhm Dual SPDT Analog Switch | Renesas

The Renesas Electronics ISL84762IU is a low-voltage, dual SPDT analog switch with 600mOhm nominal on-resistance, two independently selectable 2:1 circuits, and a 10-pin MSOP package. It operates from 1.65V to 3.6V and supports bidirectional signal paths, making it suitable for low-voltage analog routing, test equipment, and portable instrumentation. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPDT configuration selects one of two terminals from a common terminal, while the dual-circuit architecture provides two independently controlled switches. The ISL84762IU combines this routing function with low on-resistance, low-voltage operation, and a compact surface-mount package suitable for space-constrained equipment. Key characteristics include a 120 MHz bandwidth, a 6ns transition time, a 14ns switching time, and a 224pF switch capacitance. The operating temperature range is -40°C to +85°C. These characteristics are important for systems that route signals generated by sensors, converters, amplifiers, or data-acquisition front ends while command signals are driven by low-voltage digital logic. The device is described as ultra-low-on-resistance and low-voltage, with operation from 1.65V to 3.6V. Its on-resistance value must be interpreted together with the manufacturer test conditions, including supply voltage and signal amplitude, because the effective resistance and switching behavior can vary with operating conditions. Control pins support 1.8V-compatible digital operation when the device operates from a 3V supply. Typical uses include portable measurement systems, battery-powered test equipment, mobile-phone and handheld signal routing, communication interfaces, and analog front ends requiring two independent SPDT paths. The compact 10-pin MSOP footprint helps reduce board area, while the bidirectional switch structure supports signal routing in either direction. Designers should verify control-pin logic levels, supply sequencing, allowable analog signal range, and switching transients against the manufacturer datasheet. Keeping routing traces short and placing the device near the signal source helps limit parasitic capacitance and interference, particularly when driving sensitive analog nodes. This product page combines the core electrical characteristics, package information, application guidance, and replacement considerations into an engineering-focused view of the ISL84762IU. It also highlights the limits of a drop-in replacement decision when package geometry and control behavior must be checked rather than inferred from the switch function alone.

Запрос цены Контакты
ISL84781IR - 8:1 Analog Multiplexer, 750mOhm, 16-TQFN | Renesas Electronics
ISL84781IR

ISL84781IR - 8:1 Analog Multiplexer, 750mOhm, 16-TQFN | Renesas Electronics

The Renesas Electronics ISL84781IR is an 8-to-1 analog multiplexer designed for low-voltage, low-power signal routing. It provides a 750 mOhm on-resistance rating, operates from a single 1.6 V to 3.6 V supply, and is available in a 16-pin thin QFN package measuring 3 x 3 mm. The device supports rail-to-rail analog signals and includes digital address inputs that are 1.8 V logic-compatible when operated from a 3 V supply. An analog multiplexer is a semiconductor switching device that routes one of several input signals to a common output. The ISL84781IR belongs to the broader interface IC and analog switch hierarchy, combining an 8:1 signal topology with low-voltage operation, low leakage, and fast switching. Its single-supply architecture is useful where system rails are limited to low voltages and where preserving signal amplitude across the selected channel is important. The ISL84781IR offers an on-resistance of 0.4 ohm with a 3.0 V supply and 0.55 ohm with a 1.8 V supply. Typical channel matching is 0.12 ohm, while on-resistance flatness across the signal range is 0.056 ohm. The low-voltage operation is supported by a supply range of 1.6 V to 3.6 V, and power consumption is specified below 0.2 microwatts in the manufacturer product-page summary. Fast switching makes the device suitable for instrumentation, test and measurement, communications, and other systems that need to select among multiple analog inputs. The manufacturer lists turn-on time of 16 ns and turn-off time of 13 ns with a 3 V supply. Break-before-make operation is guaranteed, helping prevent two channels from being connected together during address transitions. An inhibit input can simultaneously open all signal paths, providing a controlled way to isolate the selected channel. The 16-pin thin QFN package supports compact PCB layouts, but its exposed pad and pin-assignment requirements should be followed exactly. Use the manufacturer pin-description table when assigning tracks, and keep analog routing away from fast digital edges. The low on-resistance makes the part useful for low-impedance sensor and signal-chain nodes, while the rail-to-rail signal capability helps preserve dynamic range when the input range approaches the supply limits. This page combines manufacturer specifications, cross-reference information, design guidance, and practical application notes for engineers evaluating the ISL84781IR in compact low-voltage routing systems.

Запрос цены Контакты
ISL84781IV - 8:1 Analog Multiplexer, 750mOhm | Renesas
ISL84781IV

ISL84781IV - 8:1 Analog Multiplexer, 750mOhm | Renesas

The Renesas Electronics ISL84781IV is a low-voltage, single-supply 8:1 analog multiplexer with an ultra-low on-resistance of 750mOhm, packaged in a 16-pin TSSOP. It is designed to route one of eight analog inputs to a common output, making it useful for signal selection, test and measurement systems, sensor interfaces, and compact data-acquisition systems. The 8:1 configuration provides broad channel selection in a small package while preserving a straightforward control interface. An analog multiplexer is a semiconductor switch that connects one source signal to a shared destination under digital control. The ISL84781IV belongs to the analog-switch and multiplexer hierarchy within interface ICs, where it sits between external signal sources and downstream measurement or processing circuitry. Its low on-resistance helps limit signal attenuation when the selected channel carries a sensor, voltage, or low-current analog signal. The main characteristics are an 8:1 circuit configuration, 750mOhm on-resistance, single-supply operation, and a 16-pin TSSOP package. The low on-resistance is particularly important because the resistance of the selected switch appears in series with the signal path. Lower series resistance can reduce amplitude loss and improve signal integrity when driving the next circuit stage. The compact TSSOP outline also supports designs that require a modest PCB footprint rather than a larger multiplexed-switch package. ISL84781IV is appropriate when one analog source must be selected from eight candidates. Typical uses include multiplexed sensor inputs, programmable signal routing, laboratory measurement interfaces, communication front ends, and embedded analog test systems. Digital select controls determine which input is connected, allowing a microcontroller or other controller to scan channels sequentially. The selected signal is then evaluated by an ADC, comparator, amplifier, or measurement instrument. Designers should verify the exact supply-voltage range, input-signal range, channel leakage, switching time, and control-logic levels against the manufacturer datasheet before finalizing a circuit. Signal-path capacitance and off-channel behavior can affect sampling accuracy, especially when multiplexing sensors with substantially different impedances or when switching between very low-level signals. The 16-pin TSSOP footprint also requires appropriate land-pattern design and careful decoupling close to the supply pins. The ISL84781IV provides a compact, low-resistance analog routing solution for designers who need an 8:1 multiplexer in a 16-pin TSSOP. Its combination of single-supply operation, 8:1 channel selection, and 750mOhm on-resistance makes it a practical building block for analog measurement and control systems where channel count, signal attenuation, and board area are important design constraints.

Запрос цены Контакты
ISL8483EIB - 5V RS-485/RS-422 Transceiver | Renesas Electronics
ISL8483EIB

ISL8483EIB - 5V RS-485/RS-422 Transceiver | Renesas Electronics

Renesas Electronics ISL8483EIB is a single RS-485/RS-422 transceiver operating from a 5 V supply, with integrated protection for driver outputs and receiver inputs against electrostatic-discharge strikes up to ±15 kV. The device is packaged in an 8-pin SOIC and supports balanced differential communications over industrial, instrumentation, automation, and point-to-point data links. A transceiver combines a differential line driver and receiver in one integrated circuit, allowing a printed circuit board to transmit and receive on the same balanced bus wiring. Within the interface-IC hierarchy, the ISL8483EIB belongs to the RS-485/RS-422 interface family, combines data communication with ESD protection, and is used where noise immunity, ground-offset tolerance, and common-mode rejection improve reliability over single-ended signaling. The manufacturer identifies the ISL8483E family as ESD-protected, low-power BiCMOS transceivers for 5 V operation. The ISL8483EIB provides one driver and one receiver in an 8-SOIC package. Its ±15 kV ESD protection is a principal feature for exposed communications equipment, while short-circuit current limiting and on-chip thermal shutdown help the driver withstand bus contention. These protections address field-level faults encountered in industrial wiring. BiCMOS construction combines bipolar and CMOS characteristics, supporting low-power operation and high-speed balanced signaling. The RS-422 mode supports point-to-point and multidrop communication, while RS-485 permits multiple drivers on a shared bus when the system designer controls inactive states, termination, and biasing correctly. The exact propagation-delay, slew-rate, data-rate, output-current, and temperature limits should be selected from the manufacturer datasheet for the intended system conditions. Typical uses include industrial sensor gateways, motor-control diagnostics, factory equipment interfaces, building automation, instrumentation links, and embedded serial buses. In each case, the transceiver converts logic-level serial information into balanced differential signals and returns differential bus data to receiver logic, reducing susceptibility to electromagnetic noise over longer interconnects. Designers should use a common ground reference between the transceiver and system electronics, place termination at the physical ends of the bus, and provide a bias network only when the installed network requires it. Protection components and chassis-ground design must be evaluated against the actual cable environment. Input and output filtering should be tested for signal-integrity margin before production release. This product page combines manufacturer specifications, source-linked availability information, interface use cases, and practical PCB-design considerations to support component selection and replacement planning. The ISL8483EIB is especially relevant when an existing 8-SOIC RS-485 or RS-422 design requires 5 V operation and ±15 kV ESD-protected driver or receiver nodes.

Запрос цены Контакты
ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas
ISL8483EIP

ISL8483EIP - 5V ESD-Protected RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8483EIP is a 5 V, single-channel RS-485/RS-422 interface transceiver with one transmitter and one receiver, packaged in an 8-pin PDIP. It provides ±15 kV ESD protection at the driver outputs and receiver inputs, combines BiCMOS circuitry with short-circuit current limiting, and includes on-chip thermal shutdown for dependable operation during bus contention. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and longer distances. RS-422 emphasizes point-to-point, balanced signaling, while RS-485 supports multidrop buses and driver-enable control. This device bridges the single-ended digital domain and the differential bus, placing it within the interface IC, communication IC, and semiconductor hierarchy. Key features include one half-duplex transmitter, one receiver, 5 V operation, and device-level ESD protection of ±15 kV. Driver short-circuit current limits help protect the outputs when a bus node is driven against another active node. Thermal shutdown adds a secondary protection mechanism when sustained contention or abnormal loading raises internal dissipation. The ISL8483 family combines BiCMOS implementation with low-power operation and two signal-rate options identified by the ISL8483 and ISL8485 family members. The E version adds enhanced ESD protection, while the receiver and driver control arrangement supports implementation of half-duplex nodes. Exact data rate, propagation delay, slew rate, and common-mode limits should be selected from the family datasheet for the intended bus topology. Typical uses include industrial RS-485 field buses, building automation equipment, factory data links, RS-422 point-to-point links, and industrial control modules. The device is particularly suitable when a design needs a single transceiver, balanced differential signaling, 5 V supply operation, and reinforced ESD protection near a connector or externally accessible cable. PCB implementation should keep the transceiver close to the connector, route the differential pair as a tightly matched pair, and provide a low-impedance return path. Decoupling capacitors should connect to the ground plane with short traces, and unused or unused-condition control inputs must be driven to defined logic levels to prevent an indeterminate bus state.

Запрос цены Контакты
ISL8483IB - 250kbps Half-Duplex RS-485/RS-422 IC | Renesas
ISL8483IB

ISL8483IB - 250kbps Half-Duplex RS-485/RS-422 IC | Renesas

Renesas Electronics ISL8483IB is a 5 V, 250 kbps half-duplex RS-485/RS-422 transceiver with separate receiver and transmitter enables, low-power shutdown, and optional slew-rate-limited operation in an 8-pin SOIC package. The part is designed for industrial-grade, point-to-point and multidrop serial-interface systems requiring bidirectional data transfer over a balanced cable. An RS-485/RS-422 transceiver is an interface IC that converts between logic-level digital signals and differential bus voltages. RS-422 provides a driver-dominant, point-to-point signaling method, while RS-485 permits multiple drivers on a shared bus when only one node transmits at a time. The ISL8483IB combines one transmitter and one receiver in one package, supporting half-duplex communication over a common pair of differential conductors. Key features include a 250 kbps data rate, a 5 V supply, separate Rx and Tx enables, and a low-power shutdown function. The verified distributor description also identifies a slew-rate-limited configuration option. Slew-rate control reduces the edge speed of transmitted signals, limiting high-frequency harmonics and electromagnetic interference at the expense of maximum signaling rate compared with an unrestricted high-speed driver. The ISL8483IB uses separate active-high receiver-enable and driver-enable controls, allowing the host to place the unused side of the transceiver into a disabled state. Its bidirectional half-duplex arrangement is useful where two endpoints exchange requests and responses over a shared pair of wires. The device also supports transmitter shutdown for systems that need to reduce supply consumption when the bus is inactive. Typical applications include industrial serial interfaces, remote monitoring equipment, data acquisition modules, building-control systems, factory automation links, and RS-485-to-TTL conversion products. The 8-pin SOIC package supports conventional surface-mount assembly. The industrial temperature grade identified by the verified distributor listing makes the device suitable for equipment operating across an extended commercial temperature range, subject to the manufacturer's specified limits. Designers should verify the complete datasheet pinout, absolute maximum ratings, recommended external network, driver-load capability, and shutdown behavior before releasing a PCB. Cabling, termination, grounding, and transceiver-enable sequencing are as important as the nominal 250 kbps rating because unbalanced or incorrectly terminated buses can cause reflections, common-mode voltage errors, and unreliable communication. This page combines verified distributor information, structured drop-in-family alternatives, application guidance, and design notes in a format designed to accelerate component selection, replacement planning, and hardware implementation.

Запрос цены Контакты
ISL8483IB-T - Half-Duplex RS-422/RS-485 Transceiver | Renesas
ISL8483IB-T

ISL8483IB-T - Half-Duplex RS-422/RS-485 Transceiver | Renesas

Renesas Electronics ISL8483IB-T is a single-channel, half-duplex interface transceiver supporting RS-422 and RS-485 communications in an 8-pin SOIC package. The device combines one driver and one receiver in a compact package, making it suitable for bidirectional industrial data links where both transmitting and receiving functions are required on the same bus. A half-duplex RS-422/RS-485 transceiver is a physical-layer interface IC that converts digital logic-level signals into differential bus signals and converts received differential signals back into logic levels. Within the interface hierarchy, the ISL8483IB-T belongs to the transceiver class of interface ICs, combining an RS-422/RS-485 driver, an RS-422/RS-485 receiver, and bus-facing control functions in one package. Differential signaling supports reliable communication over longer cable runs while reducing sensitivity to common-mode noise. The verified manufacturer-related listing identifies the ISL8483IB-T as a one-driver, one-receiver, half-duplex RS-422/RS-485 transceiver in an 8-SOIC package. Its principal engineering benefits are component consolidation, a compact surface-mount footprint, and support for both RS-422 and RS-485 point-to-point networks. The single driver and receiver arrangement also helps designers manage bus direction explicitly in half-duplex systems. The part is appropriate for industrial controllers, factory automation equipment, remote sensor interfaces, and embedded communications modules. In these systems, the transceiver connects a host UART or programmable controller to a differential bus while converting logic signals to and from the physical network. The 8-pin SOIC package supports conventional PCB assembly methods and is smaller than many legacy through-hole transceiver packages. Designers should verify the final electrical limits, receiver fail-safe behavior, driver enable polarity, and bus termination requirements against the manufacturer datasheet before releasing production hardware. In half-duplex implementations, correct driver-enable timing is essential to prevent contention, while proper biasing and termination help maintain signal integrity on the RS-422 or RS-485 network. This page combines the verified Renesas product identity, exact package classification, interface capability, sourcing information, available drop-in references, and practical implementation guidance. It is intended to help engineers identify the correct device, plan PCB connections, and compare compatible RS-422/RS-485 interface options before detailed circuit validation.

Запрос цены Контакты
ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas
ISL8483IBZ

ISL8483IBZ - 5V RS-422/RS-485 Transceiver | Renesas

The Renesas Electronics ISL8483IBZ is a 5 V, low-power RS-422/RS-485 interface transceiver with one transmitter and one receiver in an 8-pin SOIC package. It operates from a 4.5 V to 5.5 V supply across a -40 °C to +85 °C temperature range. Its slew-rate-limited driver is designed to reduce electromagnetic interference and reflections associated with poorly terminated transmission lines or unterminated stubs. An RS-422/RS-485 transceiver is an interface IC that converts logic-level signals into differential line signals and receives differential line signals back into logic-compatible outputs. The wider category hierarchy is transceiver > line driver and receiver > differential interface IC > interface IC > semiconductor. These devices support communication over cables and printed-circuit-board traces where noise immunity, galvanic signal polarity, and multi-drop behavior are important engineering considerations. The ISL8483IBZ combines one differential driver and one differential receiver in a single 8-SOIC package. Its operating supply range of 4.5 V to 5.5 V suits conventional 5 V equipment, while the industrial temperature range supports factory automation, instrumentation, and embedded control systems. Slew-rate limiting is particularly useful in multidrop and multipoint networks because it reduces edge energy and helps limit reflected signals on imperfectly terminated cables. The device family documentation distinguishes high-speed and slew-rate-limited RS-485/RS-422 implementations. ISL8483-family devices use slew-rate-limited drivers to reduce EMI and minimize reflections from improperly terminated transmission lines or unterminated stubs. Exact data rate, receiver thresholds, driver output impedance, and propagation-delay limits must be taken from the manufacturer datasheet when they are required for link-budget or timing calculations. Typical applications include industrial sensor buses, factory-floor equipment interfaces, building-control networks, remote instrumentation, and embedded serial links. The differential interface can improve noise tolerance over longer interconnects than a single-ended implementation, provided the network uses the correct topology, termination, biasing, and common-mode limits. PCB design should preserve a continuous ground reference beneath the transceiver, keep differential traces closely coupled, and place termination and any fail-safe bias network at the physical cable ends. Avoid adding large test pads or unrelated high-current paths between the differential pair because those structures can unbalance the pair and reduce common-mode noise rejection. This product guide consolidates the verified package, voltage, temperature, interface, and sourcing information into an engineer-oriented reference. It also distinguishes the exact ISL8483IBZ from the ESD-protected ISL8483E-family option and identifies where pinout, timing, and application-specific conditions must be confirmed in the manufacturer documentation.

Запрос цены Контакты