Товары (44.000+)

ISL8483IP - 5V RS-485/RS-422 Transceiver | Renesas
ISL8483IP

ISL8483IP - 5V RS-485/RS-422 Transceiver | Renesas

Renesas ISL8483IP is a single half-duplex RS-485/RS-422 transceiver operating from a 5 V supply, with selectable low-power high-speed or slew-rate-limited operation. The device combines one transmitter and one receiver in an 8-pin PDIP package and includes separate receiver and transmitter enables plus a low-power shutdown function. Verified distributor data identifies the ISL8483IP as a 250 kbps half-duplex RS-485/RS-422 transceiver with Rx/Tx enables and low-power SHDN. The package is specified as 8-DIP, or 8-PDIP, with a 0.300 inch, 7.62 mm body width. An RS-485/RS-422 transceiver is a balanced-interface interface IC used to connect a logic-level controller to a differential communication bus. RS-422 generally describes a point-to-point, balanced digital interface, while RS-485 supports multipoint bus arrangements and commonly uses transceivers that can disable their drivers when idle. The ISL8483IP belongs to the interface IC hierarchy and is intended for industrial-control, instrumentation, and embedded serial links requiring a 5 V supply and differential noise immunity. The verified data identifies a maximum signaling rate of 250 kbps and offers two operating approaches described as high speed or slew-rate limited. These modes are relevant when a design must balance communication rate against the transition rate of the differential driver. Additional control features named in the source material are the receiver enable, transmitter enable, and low-power shutdown input, allowing the host to manage bus direction and conserve power when communication is inactive. The ISL8483IP uses BiCMOS technology in the Intersil RS-485 and RS-422 product family. Although the provided search results describe the family as meeting both RS-485 and RS-422 standards, detailed limits for differential output voltage, receiver threshold, common-mode range, supply-current behavior, and isolation are not included in the supplied excerpts. Those parameters therefore require confirmation in the manufacturer datasheet before final circuit release. Typical applications include industrial sensor and actuator links, factory automation equipment, building-control systems, laboratory instrumentation, and embedded controllers communicating with remote RS-485 peripherals. The 250 kbps rate is appropriate for moderate-speed control and monitoring networks rather than high-bandwidth data transfer. In a multidrop bus, only one transmitter should normally be active at a time, while the receiver can monitor bus state when its driver is disabled. A key design consideration is the distinction between the PDIP and surface-mount ISL8483 package variants. Cross-reference results explicitly identify ISL8483EIBZ-T and ISL8483EIBZ-T7A as SOIC-8 surface-mount parts, so they are not drop-in replacements for an 8-PDIP board footprint. Before routing a replacement PCB, verify supply voltage, data rate, enable polarity, shutdown behavior, pinout, and transceiver-versus-receiver configuration against the manufacturer datasheet. This page consolidates the verified distributor descriptions, package distinctions, sourcing links, and practical replacement constraints into an engineering-focused view. It also identifies where the supplied evidence is incomplete, avoiding unsupported claims about pin assignments, electrical limits, lifecycle state, pricing, and thermal performance. Those fields should be completed from the authoritative manufacturer datasheet and current authorized distribution records.

Запрос цены Контакты
ISL8484IR - 4.5V Dual SPDT Low-RON Switch | Renesas
ISL8484IR

ISL8484IR - 4.5V Dual SPDT Low-RON Switch | Renesas

The Renesas Electronics ISL8484IR is a low-voltage, bidirectional, dual single-pole/double-throw analog switch with an ultra-low ON-resistance, a +1.65 V to +4.5 V single-supply range, and a 10-pin DFN package with an exposed pad. Its specified ON-resistance is 0.29 ohm at a 4.3 V supply, 0.33 ohm at 3.0 V, and 0.55 ohm at 1.8 V. The device contains two independently controlled SPDT switches, allowing one signal or supply path to be routed between two external nodes at a time. Typical on-resistance matching between channels is 0.06 ohm, while ON-resistance flatness across the signal range is 0.03 ohm. An analog switch is a semiconductor device that connects or disconnects an electrical signal path with controlled resistance. In the product hierarchy, the ISL8484IR is an analog switch and multiplexer within the broader interface IC category. Each SPDT configuration provides a common terminal, one normally closed throw, and one normally open throw, making the device useful for signal routing, polarity selection, test-point isolation, and compact analog multiplexing. The defining feature of the ISL8484IR is its low channel resistance across a low-voltage supply range. The manufacturer datasheet also identifies it as a pin-compatible replacement for the MAX4684 and MAX4685. Its low power consumption, specified below 0.45 microwatt in the cited operating conditions, and fast switching behavior make it appropriate for battery-powered and portable equipment where signal-path resistance and energy use both matter. The two independent SPDT switches provide routing flexibility without requiring two separate packages. Matching and flatness characteristics help reduce channel-dependent attenuation and distortion when a design switches between sources or measures multiple nodes. The bidirectional signal path also permits operation in either current direction, although the permitted voltage and current limits must remain within the manufacturer ratings. Typical uses include low-voltage audio routing, sensor selection, test and measurement interfaces, portable instrumentation, and general-purpose power or signal multiplexing. The low 1.65 V minimum supply supports systems operating from a single lithium-cell rail or other low-voltage source. In precision analog paths, engineers should verify the actual ON-resistance, leakage, charge injection, and switching timing under the intended signal amplitude and frequency. The primary design consideration is preserving the exposed-pad thermal and electrical requirements of the 10-DFN package. Place the exposed pad on a PCB thermal-via and ground-plane structure, keep high-current paths physically short, and confirm the selected switch state during power-up. Because the supplied search data does not include the complete pin table, engineers should download the Renesas datasheet before assigning signals to physical pins. This page consolidates the verified manufacturer description, parametric ON-resistance data, operating-voltage range, package information, and cross-reference evidence. It also distinguishes documented drop-in replacements from package or packaging variants that are not true PCB drop-in choices, helping engineers evaluate replacement risk before redesigning a board.

Запрос цены Контакты
ISL8484IRZ - 0.4 Ohm Dual SPDT Analog Switch | Renesas
ISL8484IRZ

ISL8484IRZ - 0.4 Ohm Dual SPDT Analog Switch | Renesas

Renesas ISL8484IRZ is a low-voltage dual SPDT analog switch with 0.4 ohm on-resistance, 2:1 multiplexing, and operation from +1.65 V to +4.5 V in a 10-lead TDFN package. The switch is designed for compact, low-voltage systems requiring low signal resistance, fast switching, and single-supply operation. An analog switch is a semiconductor device that routes analog signals between input and output terminals under digital control. The SPDT configuration provides one common terminal and two switched terminals for each circuit, allowing two independent 2:1 selections. In the power-management hierarchy, this dual SPDT switch functions as a low-voltage interface IC for signal routing, test-point multiplexing, and programmable analog paths. Key electrical characteristics include an on-resistance of 0.29 ohm at +4.3 V, 0.33 ohm at +3.0 V, and 0.55 ohm at +1.8 V. On-resistance matching between channels is 0.06 ohm, while flatness across the signal range is 0.03 ohm. At +4.3 V, turn-on time is 40 ns and turn-off time is 20 ns. The device also provides guaranteed break-before-make behavior. The dual independent-switch architecture supports simultaneous routing of two analog signals. Its low-voltage supply range makes it suitable for battery-powered instrumentation, portable measurement systems, low-voltage test equipment, and mixed-signal interfaces. The manufacturer identifies the ISL8484 as a pin-compatible replacement for the MAX4684 and MAX4685, with particularly low on-resistance across its stated supply conditions. Typical circuit roles include selecting between two sensors, connecting a test fixture to a measurement instrument, routing one of two sources into an amplifier, and multiplexing an analog control point. Because the switch operates from a single supply, system designers should confirm that every driven signal remains within the permitted input and output range during switching transitions. For layout, route the common, switched, and control traces with short analog paths and maintain a continuous ground reference beneath the device. Place bypass capacitance near the supply pin and avoid routing high-impedance signals beneath digital control traces. These practices reduce parasitic distortion and coupling during the 40 ns switching transitions. This product page combines the manufacturer specifications with a parameter-by-parameter comparison, verified pin-compatible alternatives, and practical routing guidance. Use the Renesas ISL8484 documentation as the authoritative source for the final pin-description table, footprint dimensions, and production release limits before releasing a PCB layout.

Запрос цены Контакты
ISL8484IU - Dual SPDT Low-Voltage Analog Switch | Renesas
ISL8484IU

ISL8484IU - Dual SPDT Low-Voltage Analog Switch | Renesas

Renesas Electronics ISL8484IU is a dual single-pole/double-throw analog switch with a single-supply operating range of +1.65 V to +4.5 V and an ultra-low on-resistance. The device contains two independent SPDT switch circuits in a 10-MSOP package and is designed for low-voltage, low-power signal-routing applications. Its stated on-resistance is 500 mOhm, while the available technical data also identifies 290 mOhm at a 4.3 V supply and 550 mOhm at a 1.8 V supply. An analog switch is an integrated interface circuit that routes electrical signals between terminals under digital control. A dual SPDT switch provides two selectable signal paths per switch section, making it useful for selecting one of two sources, routing a measurement signal, or supporting bidirectional communication. The ISL8484 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. The principal feature of the ISL8484IU is its low on-resistance across a low-voltage supply range. Available data lists on-resistance matching between channels as 0.06 Ohm and on-resistance flatness across the signal range as 0.03 Ohm. Power consumption is specified below 0.45 uW, while fast switching action is available when the supply is 4.3 V. These characteristics suit compact equipment operating from a single low-voltage rail. The device uses separate select and common terminals for each SPDT section. The 10-MSOP surface-mount package is offered in a 0.118-inch by 3.00 mm width format. The supplied data identifies the industrial temperature grade and 10 terminals. A publicly verified pin-number-to-pin-name diagram was not present in the supplied results, so the exact pinout is intentionally left unassigned rather than inferred from generic package conventions. Typical uses include low-voltage audio routing, sensor and measurement-signal selection, portable test equipment, communication-signal multiplexing, and compact industrial interfaces. For bidirectional signal paths, the control and common terminals must be operated within the voltage limits specified by the manufacturer datasheet. Care is required when switching powered signals because the exact overvoltage and break-before-make behavior should be confirmed from the current datasheet. A primary design consideration is the relationship between supply voltage and switch resistance. Lower supply operation provides less headroom for the internal switch and corresponds to higher resistance, while operation near 4.5 V provides the lower-resistance behavior listed in the available data. PCB layout should keep routing short and provide a stable return path, especially when the switch handles high-bandwidth or low-amplitude signals. This product page consolidates the verified manufacturer description, distributor inventory information, package details, switch characteristics, cross-reference findings, and practical engineering guidance. It also separates verified facts from unavailable values so designers can identify the target part quickly while recognizing which parameters still require confirmation in the current manufacturer datasheet.

Запрос цены Контакты
ISL8484IUZ - Dual SPDT Analog Switch, 0.29 Ohm | Renesas
ISL8484IUZ

ISL8484IUZ - Dual SPDT Analog Switch, 0.29 Ohm | Renesas

The Renesas Electronics ISL8484IUZ is a dual single-pole/double-throw (SPDT) analog switch with 0.29 ohm ON-resistance at V+ = 4.3 V, operating from a single +1.65 V to +4.5 V supply, and packaged in a 10-lead MSOP (10-TFSOP). Each switch routes one common node to one of two throws, giving two independent 2:1 muxes in one IC. An analog switch (also called a mux or multiplexer) is an integrated circuit that steers a signal path between multiple sources and destinations under digital control. It belongs to the signal-path hierarchy: analog switch -> multiplexer -> interface IC -> integrated circuit. Unlike a relay or mechanical contactor, it switches in nanoseconds, draws micro-watts of power, and introduces only a small, well-characterized series resistance plus a few picofarads of parasitic capacitance. Key features of the ISL8484IUZ include very low ON-resistance that stays flat across the signal range, excellent channel-to-channel rON matching of 0.06 ohm, low power consumption below 0.45 microwatts, fast switching of 40 ns tON and 20 ns tOFF at V+ = 4.3 V, guaranteed break-before-make behavior, and an HBM ESD rating of greater than 8 kV. The manufacturer also documents the ISL8484 family as a pin-compatible replacement for the MAX4684 and MAX4685. Because ON-resistance is only 0.29 ohm and rON flatness across the signal range is 0.03 ohm, the device behaves almost like a shorted trace when closed. This makes it well suited to routing low-frequency analog signals, sensor outputs, reference voltages, and baseband paths where added resistance would degrade accuracy. The very low switching energy keeps the switch usable in battery-powered and portable equipment. Typical uses include audio and headphone signal routing, portable test equipment, battery-powered sensor interfaces, USB and peripheral routing in low-voltage designs, and general-purpose analog multiplexing in consumer and industrial systems running from 1.8 V to 3.3 V rails. The key design consideration is supply headroom: the switch operates down to +1.65 V, but ON-resistance rises sharply as V+ falls (0.55 ohm at 1.8 V versus 0.29 ohm at 4.3 V). Budget the signal-path error against the highest rail in your system, and treat the control pins as logic inputs referenced to the same V+ supply.

Запрос цены Контакты
ISL8485CB - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485CB

ISL8485CB - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8485CB is a 5V, low-power, high-speed RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package. It combines one driver and one receiver in a single integrated circuit for balanced industrial communication links, with a verified data rate of up to 5Mbps. The device operates from a single 5V supply and supports both high-speed and slew-rate-limited communication modes. Its 8-SOIC package is suitable for conventional surface-mount PCB assembly, while its half-duplex architecture allows one transceiver to share a bidirectional bus with controlled driver enable and receiver enable functions. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and receives differential signals back into CMOS-compatible logic levels. The ISL8485CB belongs to the transceiver hierarchy of interface ICs, where RS-422 provides a balanced point-to-point or multidrop communication format and RS-485 supports longer, noise-tolerant multipoint buses. The part is intended for systems that require compact, reliable differential signaling rather than a single-ended communications interface. The primary electrical attributes include a 5V supply, a 5Mbps data rate, one integrated driver, and one integrated receiver. The manufacturer family documentation identifies the ISL8485 as a CMOS 5V-powered RS-485/RS-422 transceiver family with low power consumption and both high-speed and slew-rate-limited configurations. The verified distributor description identifies the CB ordering code as an 8-SOIC, while the manufacturer document covers the related ISL8485, ISL8490, and ISL8491 family. Typical uses include industrial control systems, factory automation, instrumentation, building automation, and embedded equipment connected through a balanced bus. In a half-duplex network, the transceiver converts transmitted data into differential bus voltage and receives remote data when the driver is disabled. The 5Mbps capability supports high-rate factory communication, while slew-rate limiting can reduce reflected signaling on longer or less controlled cables. Designers should verify the complete pinout, enable polarity, driver and receiver disable behavior, termination requirements, and electrical limits against the Renesas datasheet before layout. RS-485 buses normally need termination at both physical ends, biasing to provide a defined idle state, and protection appropriate to the installation environment. The 8-SOIC package requires thermal and layout attention at elevated data rates or long-cable installations.

Запрос цены Контакты
ISL8485CB-T - 5V RS-485/RS-422 Transceiver | Renesas
ISL8485CB-T

ISL8485CB-T - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8485CB-T is a 5 V, low-power RS-485/RS-422 line transceiver packaged in an 8-pin SOIC. It supports data rates up to 5 Mbps, operates from a 4.5 V to 5.5 V supply, and presents one unit load to an RS-485 bus. The device combines one driver and one receiver in a half-duplex transceiver arrangement for balanced industrial communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals between a host controller and a differential communication bus. The driver transmits complementary differential signals, while the receiver detects the voltage difference across the pair. As a single-channel half-duplex transceiver, the ISL8485CB-T supports one communication line while sharing the same package and bus connection structure used by related ISL8485 devices. The family is specified for 10% supply tolerance, providing a 4.5 V to 5.5 V operating range. Its BiCMOS construction supports low power consumption while operating at rates up to 5 Mbps. The ISL8485CB-T also provides ESD-protected, single-driver, single-receiver operation, making it suitable for point-to-point RS-422 links and multidrop RS-485 networks that require compact, surface-mount transceivers. Renesas describes the ISL8485 family as a collection of 5 V-powered RS-485 and RS-422 transceivers. The CBZ-T ordering code is associated with a lead-free and RoHS-compliant version, while the CB-T designation identifies the tape-and-reel ordering configuration used in this listing. The 8-pin SOIC package supports conventional surface-mount assembly and is compatible with compact industrial and embedded control equipment. Typical uses include industrial serial links, factory automation equipment, building controls, instrumentation, and embedded systems communicating over long differential cable runs. The 5 Mbps maximum data rate supports moderately high-speed control and data traffic, while the one-unit-load bus loading helps preserve network capacity when multiple transceivers share a bus. PCB design should account for the difference between supply current and bus return current. Place the transceiver close to the connector and transceiver protection network, keep the differential pair routed as a tightly coupled pair, and provide the supply bypass capacitance recommended by the manufacturer. The 8-pin SOIC footprint should be checked against the PCB library before substitution because narrow-body variants can differ in lead width and courtyard dimensions. This product page combines the manufacturer family description, distributor package and ordering information, current sourcing records, interface characteristics, and practical replacement guidance. It also distinguishes the exact ISL8485CB-T ordering code from related ISL8485 variants so engineers can evaluate footprint, supply, ESD, and rate requirements before approving a replacement.

Запрос цены Контакты
ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
ISL8485CBZ

ISL8485CBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

Renesas Electronics ISL8485CBZ is a 5 V, half-duplex, 1-transceiver/1-receiver RS-485 and RS-422 interface IC capable of operation to 5 Mbps. It is packaged in an 8-pin SOIC and supports a 4.5 V to 5.5 V supply range, providing tolerance for industrial 5 V rails. The device presents one unit load to an RS-485 bus and combines a balanced line driver, differential receiver, and half-duplex control in a compact package. An RS-485/RS-422 transceiver is an interface device that translates logic-level signals into balanced differential signals for reliable communication over longer cables and electrically noisy environments. It belongs to the interface IC hierarchy, connecting digital controllers and processors to field buses or point-to-point differential links. Balanced signaling improves common-mode noise immunity, while bus direction control allows a single transceiver pair to support two-way communication. Key characteristics include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply, and compatibility with both RS-485 and RS-422 communication standards. The half-duplex configuration multiplexes driver and receiver functions onto shared bus pins. Driver short-circuit current limiting and on-chip thermal shutdown help the device withstand bus contention without damage, as described in the Renesas ISL8485, ISL8490, and ISL8491 datasheet. The ISL8485CBZ uses a BiCMOS implementation and presents one unit load to the RS-485 bus. Its receiver and driver interface supports industrial communication equipment where compactness and data rate are important. Because the transceiver operates from a narrow 5 V supply range, the system must maintain 4.5 V to 5.5 V at the device for specified operation. Cabling, termination, grounding, and controlled edge rates remain important when maximizing channel integrity. Typical uses include industrial RS-485 controllers, building-automation equipment, factory data links, instrumentation gateways, and serial interface expansion for embedded processors. The 5 Mbps capability is useful for short, properly terminated links that need higher throughput than conventional slow-speed field-bus transceivers. For longer cables or lower data rates, engineers should also evaluate propagation delay, transceiver mode timing, and the loss budget of the selected cable. Place the transceiver close to the connector and bus interface to minimize unprotected trace length. Use a proper differential pair with consistent geometry, connect the receiver ground reference appropriately, and install termination only where dictated by the network topology. Decoupling capacitors should be positioned close to the supply and ground pins, while the driver-enable and receiver-enable timing must leave sufficient propagation delay for clean direction changes.

Запрос цены Контакты
ISL8485CP - 5V RS-485/RS-422 Transceiver | Renesas
ISL8485CP

ISL8485CP - 5V RS-485/RS-422 Transceiver | Renesas

Renesas ISL8485CP is a 5 V, low-power, half-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, supplied in an 8-pin through-hole PDIP package. It is designed for balanced industrial communication links where a single transceiver must support both differential transmit and receive operation. The verified distributor data identifies the device as a 1/1 RS-422 and RS-485 transceiver in an 8-PDIP package. A transceiver combines a differential line driver and differential receiver into one interface component. In the transmit direction, the driver converts a logic-level signal into a balanced differential voltage across a twisted-pair bus; in the receive direction, the receiver converts the differential bus voltage back into a logic-level signal. RS-422 commonly supports point-to-point, balanced signaling, while RS-485 permits multiple drivers and receivers on a shared bus when the system implements the required addressing, biasing, and contention controls. The ISL8485CP family is identified as a low-power 5 V RS-485/RS-422 solution with options described by the manufacturer as high-speed or slew-rate-limited. This distinction is important when designing a bus: slew-rate control can reduce high-frequency ringing and electromagnetic interference, while a high-speed configuration can improve propagation delay. The exact speed, slew-rate, output-current, and receiver-threshold limits are not present in the supplied verified excerpts and must be confirmed in the manufacturer datasheet before final circuit design. The device is implemented in an 8-PDIP package for through-hole assembly rather than a compact surface-mount land pattern. This makes it suitable for industrial controllers, data-acquisition equipment, instrumentation, and legacy interface boards where DIP soldering, prototyping, or through-hole serviceability is preferred. The balanced interface also helps reject common-mode noise when the transmitter and receiver reference a common signal ground and the cable routing is controlled. Typical applications include factory-floor serial links, industrial control modules, remote sensor interfaces, laboratory equipment, and building automation equipment. Designers should confirm the device's exact drive strength, receiver thresholds, data rate, enable or shutdown behavior, and bus termination requirements from the full datasheet. They should also verify whether a fail-safe receiver, ESD rating, slew-rate selection, or automotive qualification is required for the target environment. This page combines verified distributor availability, package information, pricing data, source links, and replacement analysis with practical RS-485 design guidance. It deliberately distinguishes confirmed facts from parameters that still require datasheet verification, helping engineers evaluate the ISL8485CP without mistaking incomplete web snippets for complete technical specifications.

Запрос цены Контакты
ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas
ISL8485ECP

ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas

The Renesas Electronics ISL8485ECP is a single half-duplex RS-485 and RS-422 line transceiver IC operating from a 5 V supply and supplied in an 8-pin PDIP package. It combines one driver and one receiver in one device, supports ESD protection to ±15 kV, and includes driver short-circuit current limiting and on-chip thermal shutdown for improved robustness during bus contention. A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers. The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring. The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration. Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture. PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process. This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.

Запрос цены Контакты
ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IB

ISL8485IB - 5Mbps RS-485/422 Transceiver | Renesas

Renesas Electronics ISL8485IB is a single half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and a 5 V supply in an 8-pin SOIC package. The ISL8485IB uses BiCMOS technology and is specified for 4.5 V to 5.5 V power supplies, including the 10% supply tolerance identified on the Renesas product page. Its industrial temperature range extends from -40°C to +85°C. An RS-485/RS-422 transceiver is a differential communications interface IC that converts logic-level transmit and receive signals into balanced, noise-immune bus signals. The ISL8485 family supports both RS-485 half-duplex operation and RS-422 balanced operation. The ISL8485 configuration multiplexes its driver output and receiver input onto the same pair of bus terminals, allowing a compact eight-pin implementation. The principal features include a 5 Mbps maximum data rate, low-power BiCMOS construction, operation from a nominal 5 V rail, and a single-unit-load RS-485 bus interface. Half-duplex operation requires the design to control the driver-enable and receiver-enable functions so that the transmitter is disabled when the bus is not being driven. These characteristics make the device appropriate for industrial data links, instrumentation, factory equipment, and point-to-point or multidrop balanced communication. The ISL8485IB is one of three related devices: the ISL8485 provides half-duplex multiplexing, while the ISL8490 and ISL8491 provide separate receive and transmit paths for full-duplex applications. The Renesas ISL8485, ISL8490, and ISL8491 datasheet identifies these architectural differences explicitly. Because bus topology and enable logic affect protocol behavior, an existing PCB should be checked for pin functions before selecting a related family member. Typical installations include RS-485 industrial sensor networks, RS-422 controller-to-peripheral links, building-control equipment, and data-acquisition systems. The 5 Mbps capability supports faster communication than legacy low-speed RS-485 links, while the differential interface helps reject common-mode noise when the transceiver is used with correctly terminated cabling. Designers should verify the eight-pin pinout, supply decoupling, driver-enable sequencing, bus termination, and protection requirements against the manufacturer datasheet. Differential routing should use a controlled-impedance layout where practical, and the unused bus terminals must be handled according to the applicable RS-485 or RS-422 configuration. This page consolidates the verified Renesas and distributor information for the ISL8485IB, documents pin-compatible alternatives with their differences, and provides practical interface-design guidance that is not available from a distributor listing alone.

Запрос цены Контакты
ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas
ISL8485IBZ

ISL8485IBZ - 5V 5Mbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8485IBZ is a single half-duplex RS-485/RS-422 transceiver operating from a 4.5 V to 5.5 V supply, with a maximum data rate of 5 Mbps, in an 8-pin SOIC package. The device combines one driver and one receiver and presents one unit load to an RS-485 bus. An RS-485/RS-422 transceiver is a balanced data-communications interface that converts logic-level signals into differential bus signals and receives differential signals from the bus. These interface ICs belong to the transceiver hierarchy within interface integrated circuits and support robust point-to-point or multipoint communication over longer distances than conventional single-ended logic links. The ISL8485 family is specified for 10% supply tolerance, allowing operation across the 4.5 V to 5.5 V range. Its BiCMOS architecture supports data rates up to 5 Mbps, making the ISL8485IBZ useful for industrial control links, factory automation equipment, instrumentation, and other balanced-communication systems. The balanced interface also improves noise immunity in environments containing switching equipment and industrial motors. The ISL8485 is a half-duplex device, so the driver and receiver share the bus connection rather than operating simultaneously. System design must account for this shared use of the interface and provide the required direction-control function. The 8-SOIC outline supports compact, surface-mount PCB construction, although exact pin names and exposed-pad details should be confirmed against the manufacturer pin-description table before routing a new design. Typical uses include RS-485 links between controllers and sensors, communication between industrial modules, and RS-422-compatible point-to-point interconnects. The 5 Mbps maximum rate supports relatively fast control and data traffic, while the differential signaling method reduces susceptibility to common-mode noise. Cable length, topology, termination, grounding, and data rate must be considered together because faster operation generally imposes more restrictive channel requirements. For PCB implementation, place the transceiver close to the connector and route the balanced pair as a tightly coupled differential pair with continuous ground referencing. Use the termination and protection strategy appropriate for the installation, and keep switching-node currents away from the receiver path. This page also organizes lifecycle, sourcing, replacement, and application guidance around the manufacturer’s ISL8485 family information.

Запрос цены Контакты
ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IP

ISL8485IP - 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8485IP is a 5V, low-power, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5Mbps and supplied in an 8-pin DIP package. It provides one balanced transceiver interface for bidirectional multipoint data communication, places one unit load on an RS-485 bus, and operates from a supply range of 4.5V to 5.5V. The device is intended for industrial communication links requiring either high-speed operation or controlled slew rates. An RS-485/RS-422 transceiver is an interface IC that converts digital logic-level signals into differential signals for balanced wired communication and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced links, while RS-485 permits multipoint buses and driver-enable control. The ISL8485IP belongs to the transceiver hierarchy within interface ICs and combines transmitter, receiver, bus-enable control, and protection functions in one package. Key features include a 5Mbps maximum data rate, 4.5V to 5.5V supply tolerance, one-unit-load bus loading, and support for both RS-485 and RS-422 signaling. The 8-pin DIP package is suitable for conventional through-hole assembly, prototyping, repair, and industrial control equipment. Its half-duplex arrangement allows the same differential pair to transmit and receive, although external direction-control logic is normally required. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation with high data-rate capability. According to the Renesas ISL8485 family information, the ISL8485, ISL8490, and ISL8491 devices are 5V-powered single transceivers that meet RS-485 and RS-422 standards. The family supports supply voltages with 10% tolerance and presents one unit load to the RS-485 bus, helping control loading when multiple nodes share a communication line. Typical applications include industrial factory automation, programmable-logic-controller communication, building-control networks, instrumentation links, and embedded serial-interface equipment. In these systems, the transceiver serves as the physical-layer interface between a controller UART or logic port and a balanced RS-485 or RS-422 cable. Its 5Mbps capability supports high-speed equipment links, while slew-rate-controlled variants in the broader family can be useful where lower EMI is the priority. PCB design should preserve the differential signal path and provide controlled termination and biasing appropriate to the selected RS-485 or RS-422 topology. Keep the transceiver close to the connector, route the differential pair as a coupled pair, and place termination components where they can be configured for the intended network. The maximum 5.5V supply is especially important in industrial systems because transients and supply tolerances must remain within the device rating. This product page combines verified distributor identification, package and interface details, family-level electrical characteristics, alternative sourcing information, and application-specific engineering guidance. It also distinguishes explicitly verified facts from parameters that require confirmation from the manufacturer datasheet before schematic release or production qualification.

Запрос цены Контакты
ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8485IPZ

ISL8485IPZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

Renesas ISL8485IPZ is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin PDIP package. It operates from a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and combines one transmitter and one receiver in a single integrated circuit. The BiCMOS implementation supports balanced industrial-communication links where a compact, single-part interface is preferred. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as logic-level outputs. RS-422 provides a point-to-point balanced communication format, while RS-485 supports multipoint bus arrangements. The ISL8485IPZ belongs to the interface-IC hierarchy within integrated circuits and is used where electrical isolation, protocol conversion, or galvanic distance is handled elsewhere in the system. The principal operating features are a 4.5 V to 5.5 V supply range, operation to 5 Mbps, half-duplex communication, and one-unit-load RS-485 bus loading. These characteristics suit equipment that exchanges data over relatively short, high-speed balanced interconnects. The integrated transmitter and receiver reduce board area compared with separate driver and receiver circuits, while the PDIP package supports conventional through-hole assembly and prototyping. The BiCMOS architecture combines bipolar and CMOS circuit techniques, allowing the device to provide high-speed differential signaling while maintaining low-power interface operation. Half-duplex operation means the transmitter and receiver share the same differential pair, so the design must correctly manage driver-enable and receiver-enable controls to prevent unwanted bus contention. The one-unit-load rating permits multiple compatible transceivers to share an RS-485 network, subject to the total-load and topology limits of the completed bus. Typical uses include industrial control equipment, factory automation links, data-acquisition equipment, instrumentation, and communications modules that connect a host controller to an RS-485 or RS-422 peripheral. The 5 Mbps capability is useful for short links carrying frequent control or diagnostic messages, although cable length, topology, termination, grounding, and transceiver delay determine the practical communication distance. Designers should place the transceiver near the connector and cable entry point, provide the required supply and bypass capacitance, and follow the manufacturer datasheet for driver-enable and receiver-enable logic. Differential pairs should be routed with consistent geometry and controlled impedance. A termination resistor is normally placed at each end of an RS-422 link; RS-485 termination practices depend on the bus topology and its signal reflections. This page combines the exact Renesas product characteristics, package information, pricing evidence, interface-family relationships, comparison parameters, and practical implementation guidance. It also distinguishes verified drop-in alternatives from near-equivalent devices that use a different package and therefore require PCB redesign rather than simple component substitution.

Запрос цены Контакты
ISL8487EIB - 5V RS-485/RS-422 Transceiver | Renesas
ISL8487EIB

ISL8487EIB - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8487EIB is a 5 V, single RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. It supports balanced data communications, provides ±15 kV ESD protection on driver outputs and receiver inputs, and offers a 1/8-unit-load receiver for demanding multidrop and multipoint networks. The family operates from a single 5 V supply and is designed for low-power industrial interfaces. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential, balanced bus signals and receives differential bus signals back into CMOS-compatible logic. The differential architecture improves common-mode noise rejection and supports communication over longer cables than single-ended interfaces. The ISL8487E belongs to the RS-485 transceiver hierarchy, within interface ICs and broader data-communication semiconductors. Key characteristics include ±15 kV ESD protection, fractional 1/8-unit loading, 5 V operation, and a maximum quiescent current of 145 µA for the ISL8487E family. The fractional loading permits as many as 256 devices on a bus under ideal conditions, subject to the network configuration and system-level constraints. Both high-speed and slew-rate-limited versions appear in the ISL8487E family, so the exact drive and data-rate limits should be confirmed from the ISL8487E datasheet before selecting the required speed grade. The BiCMOS implementation combines low power with balanced-line drive capability. The receiver can monitor bus activity independently of the driver, while the driver and receiver enables support controlled connection to a multidrop network. The ±15 kV protection is particularly useful in industrial environments where cables may connect to external equipment and exposed connectors. Typical applications include industrial process automation, remote meter reading, building controls, factory equipment links, multidrop instrumentation buses, and point-to-point RS-422 links. The low 1/8-unit load is valuable when many nodes share one bus, while the small SOIC-8 package simplifies PCB routing in compact control equipment. When laying out the circuit, route the differential A and B traces as a closely coupled pair, provide the transceiver-side decoupling recommended by the manufacturer datasheet, and use chassis-ground protection methods at exposed connectors. Termination remains a network-level decision: terminate the far ends of the bus rather than every node, and confirm whether the selected family member uses slew-rate-limited or high-speed drive. This page combines the manufacturer family specifications, package and interface details, comparison guidance, and practical PCB considerations to accelerate transceiver selection for balanced industrial communication links.

Запрос цены Контакты
ISL8487IB - 250 kbps RS-485/422 Transceiver | Renesas
ISL8487IB

ISL8487IB - 250 kbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8487IB is a 5 V, single-channel half-duplex RS-485/RS-422 interface transceiver with a 250 kbps data rate, 1/4 unit load, and an 8-pin SOIC package. It combines one driver and one receiver in a fractional-unit-load design intended for balanced industrial communication links where the number of connected nodes is important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into digital logic. Positioned within the hierarchy of transceiver, communication interface, interface IC, and semiconductor categories, the ISL8487IB supports RS-485 and RS-422 networks while presenting a lower bus loading than a one-unit-load device. The ISL8487IB operates from a 5 V supply and presents a 1/4 unit load, allowing up to 128 transceivers on a compliant RS-485 bus. Its maximum data rate is 250 kbps, and the listed receiver hysteresis is 70 mV. The 8-SOIC surface-mount package measures approximately 0.154 inches, or 3.90 mm, in width and supports conventional board-assembly and inspection processes. Because the device is a half-duplex transceiver, the receiver and driver share the bus path and direction is controlled by the DE and RE inputs. This architecture suits point-to-point links as well as multidrop buses in which multiple nodes may communicate under a token-passing or polled protocol. The fractional unit load reduces input impedance loading compared with a standard one-unit-load transceiver, improving scalability without requiring an alternative physical bus topology. Typical applications include industrial process monitoring, factory automation, remote meter reading, building controls, instrumentation, and general-purpose RS-485 or RS-422 links. The 250 kbps rate is suitable for supervisory communications and moderate-speed data transfer, while the 1/4 unit load is especially useful when several nodes must share the same twisted-pair bus. Because the transceiver is not galvanically isolated, applications with large ground-potential differences may require an external isolation strategy. Designers should verify termination, biasing, differential routing, and protection against the electrical environment of the cable. The differential pair should be routed as a controlled-impedance pair where practical, and the transceiver should be placed close to the connector to minimize unprotected trace exposure. Supply decoupling and grounding must follow the manufacturer datasheet recommendations. This page combines verified distributor specifications, lifecycle information, source-linked pricing, package details, application guidance, and defensible same-footprint alternatives. It also distinguishes confirmed data from parameters not present in the supplied source material, helping engineers evaluate the obsolete ISL8487IB without assuming unverified electrical characteristics.

Запрос цены Контакты
ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas
ISL8487IB-T

ISL8487IB-T - Low-Power RS-485/422 Transceiver | Renesas

Renesas ISL8487IB-T is a half-duplex, single-transceiver interface IC for RS-485 and RS-422 data links, operating from a 5 V supply and offering one-quarter unit-load drive capability in an 8-pin SOIC package. The ISL8487IB-T combines a low-power RS-485/RS-422 transceiver with ESD-protected communication pins, making it suitable for industrial control, instrumentation, and point-to-point or multidrop serial networks where low power and compact packaging are important. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level transmit and receive signals into differential bus signals and converts incoming differential signals into CMOS-compatible logic. The RS-485 standard supports balanced, multipoint communication over relatively long cables, while RS-422 is commonly used for point-to-point links. Within the interface hierarchy, the ISL8487IB-T belongs to the RS-485/RS-422 transceiver class of communication interface ICs. The device is identified as a one-transceiver, half-duplex component with one-quarter unit-load drive capability. Its 5 V operation and low-power design make it appropriate for embedded systems in which every milliampere affects system thermal performance or battery life. The 8-pin SOIC package also supports compact, surface-mount PCB construction while providing enough pins for separate driver input, receiver output, enable control, supply, and ground connections. The one-quarter unit-load rating enables the device to present only one quarter of a standard unit load to the bus. This loading capability allows more nodes to share a multidrop network than a one-unit-load transceiver while preserving signal integrity. Its half-duplex architecture supports shared transmit and receive circuitry, reducing board area and simplifying bus direction control in designs that do not require simultaneous full-duplex operation. Typical uses include industrial sensor gateways, programmable logic controller communication, building automation, remote I/O modules, instrumentation, and embedded serial controllers. The part is particularly appropriate when the bus cable length, node count, ground-reference conditions, and data rate remain compatible with the limits of the Renesas ISL8487 family. A network should still be checked for termination, biasing, and transient protection requirements. PCB implementation should keep the transceiver close to the bus connector and provide a continuous ground reference between the transceiver and connector. Place network termination and any failsafe biasing components where they can be selectively configured, and confirm that the logic interface voltage of the connected controller is compatible with the transceiver. The SOIC footprint simplifies assembly, although exposed bus and logic pins still require careful handling during soldering. This product page combines package and interface details, commercially focused sourcing guidance, pin-compatible candidate evaluation, and application-specific design guidance. It is intended to help engineers verify the electrical trade-offs and board-level requirements before integrating the ISL8487IB-T into an RS-485 or RS-422 system.

Запрос цены Контакты
ISL8487IBZ - 5V RS-485/RS-422 Transceiver | Renesas
ISL8487IBZ

ISL8487IBZ - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8487IBZ is a 5 V, single-channel RS-485 and RS-422 transceiver in an 8-pin SOIC package. It combines one driver and one receiver, supports a fractional 1/8 unit load, and provides the differential interface required by balanced industrial-communication links. The device is identified as an ESD-protected 8-SOIC transceiver, making it suitable for compact RS-485 equipment, multidrop field buses, industrial control systems, and point-to-point RS-422 links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential voltage waveforms for reliable communication over balanced copper cables. The transmitter drives a differential output, while the receiver converts the differential input into a logic-level signal. By placing a common-mode voltage range and differential signaling between two conductors, this interface class supports improved noise immunity compared with single-ended communication. The ISL8487 family therefore sits between a host controller and a physical network such as Modbus RTU, PROFIBUS-related equipment, or proprietary industrial buses. The ISL8487IBZ operates from a 5 V supply and is designed for low-power, high-speed or slew-rate-limited communication. Its fractional 1/8 unit-load characteristic allows more receiving nodes on a multidrop bus than a conventional one-unit-load transceiver. Because the package contains one transmitter and one receiver, it can support half-duplex communication when the driver and receiver controls are managed by the host. The device also includes ESD protection, an important feature for transceiver devices connected to external cables and field-accessible equipment. The family is described as BiCMOS and is designed to meet RS-485 and RS-422 balanced-communication requirements. Its low-power operation suits distributed equipment where every milliampere can affect system thermal design. In half-duplex networks, the receiver may remain active while the driver is disabled, allowing the attached controller to detect responses or bus contention. Designers should still control the enable and disable timing to prevent the driver from fighting an external driver during bus turnaround. Typical uses include industrial sensor gateways, PLC communication ports, building-control terminals, instrumentation, data-acquisition equipment, and factory automation nodes. The 8-SOIC package also supports compact peripheral boards where a larger multi-channel transceiver would be unnecessary. In a typical multidrop network, the ISL8487IBZ connects a UART or embedded controller to the balanced bus, while termination and biasing components are placed only where required by the network topology. The main design consideration is cable-side protection. Although the device includes ESD protection, the maximum bus voltage, common-mode range, ground-reference limits, connector placement, and external surge-protection requirements must be checked against the application environment. Keep the balanced pair tightly coupled, connect the transceiver ground reference appropriately, and verify termination and fail-safe behavior for the selected operating mode. The 5 V supply should be decoupled close to the device, and unused control inputs must not float. This page combines the component identity, RS-485/RS-422 interface characteristics, package information, replacement guidance, comparison details, and practical PCB-design considerations into a focused engineering reference. It also identifies the available same-package alternatives and distinguishes the verified role of each candidate for drop-in replacement decisions.

Запрос цены Контакты
ISL8487IP - 5V Half-Duplex RS-485/RS-422 Transceiver | Renesas
ISL8487IP

ISL8487IP - 5V Half-Duplex RS-485/RS-422 Transceiver | Renesas

Renesas ISL8487IP is a 5 V, half-duplex RS-485/RS-422 interface transceiver with one transmitter and one receiver in an 8-pin PDIP package. It supports a 1/8-unit-load receiver characteristic, low-power operation, driver-enable and receiver-enable control, and a low-power shutdown function. These characteristics make it suitable for bidirectional serial-data links that require both RS-485 and RS-422-compatible signaling without a separate supply rail for the interface. An RS-485/RS-422 transceiver is a differential interface IC that converts logic-level data into balanced differential signals and converts incoming differential signals back into receiver-compatible logic. Within the broader hierarchy, it is a transceiver interface IC, a wired-communication interface, and part of the broader semiconductor and industrial-control ecosystem. Its half-duplex architecture allows a pair of devices to share the same differential pair, although only one transmitter should drive the bus at a time. The ISL8487IP provides a 1/8-unit-load receiver, allowing multiple nodes to share a bus more effectively than a one-unit-load receiver. Its 5 V supply, low-power shutdown, separate transmitter and receiver enables, and selectable high-speed or slew-rate-limited operation give the designer several ways to balance throughput, EMI control, and power consumption. The transmitter-enable and receiver-enable inputs also support orderly bus-direction control in half-duplex equipment. According to the manufacturer datasheet, the device uses fractional-unit-load BiCMOS transceiver technology intended for balanced RS-485 and RS-422 networks. The slew-rate-limit option reduces the rate of change on driver output edges, which can help control high-frequency ringing and electromagnetic emissions. Conversely, the high-speed mode is intended for links where maximum communication rate is more important than edge-rate control. Exact propagation-delay, data-rate, differential-output, and current-limit values were not present in the supplied web data. Typical uses include industrial equipment links, building-control interfaces, instrumentation buses, data-acquisition systems, and host-controller communication ports. In a half-duplex system, the transceiver can connect a controller to a multidrop field bus while logic-controlled enables determine whether the node transmits or receives. The low-power shutdown function is useful when a connected module must reduce current consumption while preserving a stable local bus connection. Designers should verify the exact recommended termination, biasing, common-mode range, and decoupling requirements in the manufacturer datasheet before release. Differential pairs should be routed with continuous references and matched spacing, while a slew-rate-limited mode may be preferable in cables or cabinets exposed to significant EMI. The 8-pin PDIP package also requires adequate spacing around the leads for soldering and inspection.

Запрос цены Контакты
ISL8488EIB - ESD-Protected RS-485/RS-422 | Renesas
ISL8488EIB

ISL8488EIB - ESD-Protected RS-485/RS-422 | Renesas

The Renesas Electronics ISL8488EIB is a single-channel, half-duplex RS-485/RS-422 interface transceiver built with BiCMOS technology and operated from a single 5 V supply. It accepts a 4.5 V to 5.5 V supply range and provides one driver and one receiver in an 8-pin SOIC package. Driver outputs and receiver inputs are protected against ESD strikes up to ±15 kV without latch-up. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and board-level interconnects. The ISL8488EIB belongs to the broader hierarchy of transceiver IC, interface IC, communication IC, and semiconductor. Its differential signaling supports noise rejection, while its integrated ESD protection helps preserve interface reliability in industrial and commercial systems where exposed connector pins may encounter electrostatic discharge. The device provides full RS-422 and RS-485 operation from a single 5 V rail. Its 10% supply tolerance allows operation across the 4.5 V to 5.5 V range rather than requiring a tightly regulated 5 V source. The integrated protection applies to both driver outputs and receiver inputs, and the BiCMOS process combines low-power CMOS characteristics with bipolar drive capability. These features make the device suitable for robust point-to-point and multidrop balanced communication links. As a single transceiver, the ISL8488EIB is appropriate when a system requires one differential bus driver and one differential receiver rather than a multi-channel interface. The SOIC-8 package supports conventional surface-mount assembly and occupies a footprint compatible with established RS-485 interface layouts. Because a transceiver combines transmit and receive functions, system design must include correct driver enable control, bus termination, fail-safe biasing, grounding, and protection arrangements appropriate to the cable environment. Typical uses include industrial serial links, building-control equipment, factory automation, instrumentation, data acquisition, and embedded communications between circuit boards. The device can also serve in RS-422 links where a dedicated balanced driver and receiver are required. Its principal design considerations are correct logic-level interfacing, controlled bus-idle states, proper termination at the physical ends of the network, and protection of long exposed cables. For reliable operation, decouple the 5 V supply close to the device and route the balanced differential pair as a tightly coupled pair. Place termination resistors only at the physical ends of the bus, and use the receiver-enable and driver-enable controls to prevent multiple transmitters from driving the same network simultaneously. Confirm the final termination, biasing, and cable-length configuration against the communication standard used by the system. This page combines the manufacturer interface description, package information, protection characteristics, verified replacement references, and practical RS-485/RS-422 design guidance. It also distinguishes direct drop-in replacements from packaging-only variants, helping engineers evaluate PCB reuse, electrical compatibility, and sourcing requirements before modifying a qualified design.

Запрос цены Контакты
ISL8488IB - 250kbps Full-Duplex RS-485/422 | Renesas
ISL8488IB

ISL8488IB - 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8488IB is a 5V, full-duplex RS-485 and RS-422 transceiver capable of operation at 250kbps in an 8-pin SOIC package. The integrated interface IC combines one transmitter and one receiver for bidirectional point-to-point or multipoint serial links, while its slew-rate-limited driver helps reduce electromagnetic interference and ringing on inadequately terminated lines. An RS-485 transceiver is a differential communications interface IC used to connect a controller, programmable logic controller, sensor, or industrial endpoint to a balanced serial bus. RS-485 is a physical-layer standard suited to noisy industrial environments and longer cable runs, while RS-422 provides compatible differential signaling for point-to-point links. The ISL8488IB occupies the interface-IC hierarchy alongside RS-232 transceivers, isolated transceivers, and CAN controllers, but it operates with differential RS-485/RS-422 signaling rather than single-ended RS-232. The verified device data identifies a 5V supply, a 250kbps maximum signaling rate, full-duplex operation, slew-rate-limited drive, low-power operation, and the absence of separate receiver-enable and transmitter-enable controls. These features make the device appropriate for industrial and commercial systems where a compact, always-enabled full-duplex interface is preferred. The 8-SOIC format also supports conventional surface-mount PCB assembly and broad availability through distributors. The full-duplex arrangement separates the differential driver and receiver paths, allowing simultaneous transmission and reception. The slew-rate-limited driver is particularly useful where long cables, branch stubs, imperfect terminations, or reflected signals could otherwise produce unwanted EMI or excessive edge ringing. The supplied search evidence does not provide a verified common-mode range, receiver sensitivity, fail-safe behavior, bus loading, or propagation-delay distribution, so those values should be confirmed from the complete manufacturer datasheet before release. Typical uses include industrial controller links, factory automation equipment, building-control systems, instrumentation, telecom equipment, and embedded serial links where RS-485 or RS-422 is already selected. Because the part has no separate RX/TX enable inputs, the attached controller must handle bus-direction control elsewhere or the transceiver must remain in its continuously enabled interface configuration. The 250kbps data rate also places the device below the throughput normally associated with modern high-speed CAN or differential Ethernet interfaces. For a new PCB, preserve the manufacturer-recommended bypass capacitance, connect the differential pair as a controlled impedance or tightly matched pair, and provide termination only where the cable topology requires it. Avoid placing long unprotected stubs on the bus. Designers should also verify ground potential differences between connected systems because RS-485 relies on the common-mode voltage remaining within the device's supported operating range. This product record combines verified distributor listings, the manufacturer-family datasheet, available cross-reference evidence, packaging details, interface-use guidance, and a conservative same-footprint replacement assessment. It also distinguishes confirmed specifications from unavailable parameters so procurement and engineering teams can identify which values still require confirmation from the full datasheet.

Запрос цены Контакты
ISL8488IB-T - 250kbps Full-Duplex RS-485/422 | Renesas
ISL8488IB-T

ISL8488IB-T - 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8488IB-T is a single RS-485/RS-422 transceiver operating from a 5 V supply, with one transmitter and one receiver in an 8-SOIC package. The device supports data rates up to 250 kbps and provides full-duplex balanced communication without separate receiver-enable or transmitter-enable controls. Its low-power BiCMOS design is intended for industrial and commercial equipment where low-power differential interfaces, compact PCB area, and controlled transition behavior are important. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals and reconstructs digital data from a differential receiver input. This device supports both RS-485 and RS-422 applications, covering point-to-multipoint bus communications and point-to-point links. Within the interface hierarchy, it belongs to the RS-485 transceiver category, uses differential signaling, and operates as a physical-layer communications component. The principal operating characteristics are a 5 V supply, a 250 kbps maximum signaling rate, full-duplex operation, and one integrated transceiver in an 8-SOIC package. The Intersil datasheet describes the ISL8488 family as a low-power, high-speed or slew-rate-limited RS-485/RS-422 device. Its balanced interface is suited to industrial networking, instrumentation, and control links where cable-length and ground-offset considerations make differential signaling preferable to single-ended logic. The BiCMOS architecture combines bipolar and CMOS process characteristics, supporting low-power operation while providing the drive and receive performance required by balanced communication links. The device accepts a 10% supply-tolerance range of 4.5 V to 5.5 V. Because the ISL8488IB-T has no receiver-enable or transmitter-enable pins, its operating state is managed entirely through the bus and data-path behavior rather than local logic-control inputs. Typical uses include industrial RS-485 controllers, factory automation equipment, building-control interfaces, instrumentation, and point-to-point RS-422 links. In these systems, the transceiver provides the physical-layer connection between a host UART or communications controller and a balanced cable. The 250 kbps ceiling makes it appropriate for moderate-speed control and monitoring traffic rather than high-speed video or storage networks. Layout should preserve the integrity of the differential pair and provide a controlled return path. Keep the two bus conductors closely coupled, route them away from high-current switching paths, and use the application guidance in the Intersil datasheet for termination and protection. Confirm the selected connector, cable, and grounding strategy satisfy the required RS-485 or RS-422 system configuration. This page consolidates the device identity, operating limits, package details, family alternatives, and implementation guidance into an engineering-focused resource. It also distinguishes verified operating facts from parameters that require confirmation against the manufacturer datasheet before production release.

Запрос цены Контакты
ISL8488IBZ - 5V Full-Duplex RS-485/RS-422 Transceiver | Renesas
ISL8488IBZ

ISL8488IBZ - 5V Full-Duplex RS-485/RS-422 Transceiver | Renesas

Renesas ISL8488IBZ is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It supports a 4.5V to 5.5V supply range, combines one driver and one receiver in each package, and is identified by the source material as an ESD-protected BiCMOS communications device. The ISL8488IBZ family is specified for both RS-485 and RS-422 balanced communication standards, making it suitable for industrial equipment, data acquisition systems, and point-to-point serial links. A transceiver such as the ISL8488IBZ belongs to the interface-IC hierarchy: transceiver → driver/receiver → differential data interface → semiconductor. RS-485 supports balanced, multipoint buses that can tolerate common-mode noise better than single-ended logic links, while RS-422 provides a balanced point-to-point interface. The ISL8488IBZ can therefore serve as the physical-layer endpoint in equipment that must exchange data reliably over cables or board-level interconnects. The key device attributes are its 5V operation, 4.5V to 5.5V tolerance, full-duplex configuration, 1/1 driver-to-receiver arrangement, 8-SOIC package, low-power BiCMOS implementation, and integrated ESD protection. The family literature identifies applications for high-speed or slew-rate-limited communication. A comparison entry lists a 250kbps operating-rate variant in an 8-pin SOIC, making that data point relevant when matching the correct suffix, but it should not be assumed to describe every device in the family without checking the manufacturer ordering guide. BiCMOS construction combines bipolar and CMOS circuit characteristics to support low-power operation with suitable communications-interface performance. In an RS-485 design, the driver converts a logic-level signal into a differential pair, and the receiver detects the voltage difference between the pair. Full duplex separates the transmit and receive paths so the device can communicate in both directions simultaneously, unlike a half-duplex implementation that must share bus drivers and control signal direction. Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, point-to-point RS-422 links, and RS-485 communications nodes. The full-duplex arrangement is particularly useful when each equipment enclosure needs an independent communication channel rather than a shared half-duplex bus. The 8-pin SOIC package also makes the device practical for conventional surface-mount PCB assembly. PCB design should preserve the differential signal topology, keep the driver and receiver ground connections compact, and route the balanced pair away from switching nodes. External termination and biasing must follow the selected RS-485 or RS-422 network topology. The 4.5V to 5.5V supply range also requires decoupling close to the device so transient current and supply noise do not degrade signal integrity. This product page combines device identification, electrical constraints, interface selection guidance, strict same-package replacement information, and application-specific design guidance. It also distinguishes the ISL8488IBZ from related suffix variants and highlights which parameters require verification in the manufacturer datasheet before production release.

Запрос цены Контакты
ISL8488IP - 250kbps Full-Duplex RS-485/RS-422 | Renesas
ISL8488IP

ISL8488IP - 250kbps Full-Duplex RS-485/RS-422 | Renesas

The Renesas Electronics ISL8488IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver operating at up to 250 kbps, supplied in an 8-pin plastic DIP package. The device is designed for bidirectional industrial data links and combines a transmitter, receiver, and bus-driver/receiver functions without separate receive or transmit enable pins. Its slew-rate-limited operation helps reduce unwanted high-frequency signal content on longer RS-485 networks. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential bus voltages and converts received differential bus signals back into CMOS-compatible logic. In the broader electronics hierarchy, it is an interface IC within the transceiver family, designed for reliable point-to-point or multipoint communication over cables and industrial backplanes. The ISL8488IP supports both RS-485 and RS-422 system requirements while operating from a single 5 V supply. Key verified characteristics include a 250 kbps maximum signaling rate, full-duplex operation, 5 V supply operation, integrated RS-485/RS-422 transceiver functionality, and slew-rate-limited signaling. The absence of dedicated transmit and receive enable inputs is useful in applications where the interface direction is fixed or managed elsewhere. Its low-power design is intended for embedded industrial, communications, instrumentation, and control systems where reduced energy use and controlled edge rates are important. The device combines differential bus outputs with a receive path designed for data-link applications. Because the ISL8488IP is slew-rate limited, engineers should evaluate its 250 kbps rating against protocol timing, cable length, termination requirements, and the waveform behavior of the connected system. The 8-PDIP package favors through-hole construction, thermal management through the printed-circuit board, and applications that favor a conventional DIP footprint over a surface-mount package. Typical uses include industrial controller links, remote instrumentation, point-to-point communications equipment, factory data acquisition, and embedded systems exchanging commands between a controller and a remote peripheral. Full-duplex operation can simplify systems that continuously require independent transmit and receive paths. The lack of separate enable pins also reduces external control logic, although it may not suit designs that require direction switching or controlled bus tri-state behavior. For a new layout, place the transceiver near the connector and bus entry, route the differential pair as a tightly coupled pair, apply the appropriate termination and protection network, and maintain a continuous ground reference where required by the communication standard. Check the manufacturer datasheet for exact receiver thresholds, driver limits, supply-current values, temperature limits, and absolute maximum ratings before releasing production hardware. This page combines the verified 250 kbps, 5 V, full-duplex, RS-485/RS-422, slew-limited, 8-PDIP, and no-enable characteristics with practical integration guidance. It also distinguishes verified facts from unavailable datasheet details so procurement and engineering teams can identify what must be checked in the full manufacturer documentation.

Запрос цены Контакты