Товары (44.000+)

ISL8489EIB - 5V Full-Duplex RS-485 Transceiver | Renesas
ISL8489EIB

ISL8489EIB - 5V Full-Duplex RS-485 Transceiver | Renesas

The Renesas Electronics ISL8489EIB is a 5 V, full-duplex RS-422/RS-485 transceiver with one driver and one receiver, operating at up to 250 kbps in a 14-pin SOIC package. It operates across a 4.5 V to 5.5 V supply range and is specified from -40°C to +85°C, combining differential bus signaling with integrated ESD protection rated to 15 kV. An RS-485 transceiver is an interface IC that converts logic-level signals into differential RS-485 or RS-422 transmissions and converts received differential signals into logic-level data. The ISL8489EIB supports both standards because its balanced driver and receiver architecture meets the signaling requirements of half-duplex multidrop RS-485 networks and full-duplex point-to-point RS-422 systems. The device belongs to the interface-IC hierarchy and supports bidirectional communication between controllers, sensors, industrial equipment, and field buses. Key features include one transmit driver, one receive receiver, full-duplex operation, 5 V operation, and a maximum data rate of 250 kbps. Its 15 kV ESD protection improves robustness against electrostatic discharge encountered during industrial installation and servicing. The -40°C to +85°C temperature range covers extended industrial environments, while the 14-pin SOIC package supports conventional surface-mount assembly and automated inspection. The BiCMOS implementation combines bipolar and CMOS characteristics, supporting low-power 5 V operation while providing the drive and receive performance required for balanced communication. Full duplex allows the driver and receiver to operate simultaneously, which is useful when transmit and receive paths must remain active. Its 250 kbps maximum rate is appropriate for industrial control buses, instrumentation links, and equipment interfaces that do not require high-speed differential data protocols. Typical applications include industrial automation controllers, RS-485 sensor gateways, motor-control equipment, building-automation nodes, and point-to-point RS-422 links between distributed modules. In a multidrop RS-485 network, the transceiver interfaces a microcontroller UART to a balanced bus while the system supplies termination and biasing components. In a full-duplex implementation, separate differential pairs provide independent transmit and receive paths. PCB design should preserve the balanced trace geometry of the bus and route driver and receiver outputs away from sensitive analog inputs. Place the transceiver close to the board connector to minimize exposed ESD paths, and use the package pin-description table in the manufacturer datasheet when assigning connector and protection-circuitry connections. The 15 kV ESD rating describes the specified protection level, not a guarantee that external surge or lightning protection is unnecessary. This page combines device specifications, verified package and ordering information, application guidance, and same-family drop-in alternatives. It also identifies the electrical details that engineers should confirm against the manufacturer datasheet when qualifying a new RS-422 or RS-485 design.

Запрос цены Контакты
ISL8489IB - 250kbps RS-485/422 Transceiver | Renesas
ISL8489IB

ISL8489IB - 250kbps RS-485/422 Transceiver | Renesas

The Renesas Electronics ISL8489IB is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps, packaged in a 14-pin SOIC. It combines one driver and one receiver in a single integrated circuit and provides both high-speed and slew-rate-limited operation. The device does not include separate receiver-enable or transmitter-enable controls, making it suitable for continuously enabled balanced communication links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. These balanced interfaces belong to the broader wired-communication hierarchy and are commonly used where noise immunity, signal integrity, and reliable communication over longer cables are more important than single-ended signaling. The verified product information identifies a 5 V supply, low power consumption, full-duplex operation, support for both RS-485 and RS-422, and data rates up to 250 kbps. Its 14-pin SOIC package supports conventional surface-mount PCB assembly. Because the device lacks separate RX and TX enable pins, it is particularly appropriate for designs that keep both directions of the balanced interface continuously active. The ISL8489 family is described by the manufacturer as a BiCMOS 5 V single-transceiver solution designed for RS-485 and RS-422 balanced communication. Its low-power architecture supports equipment in which multiple interface channels may be present. High-speed or slew-rate-limited operation gives designers a choice according to cable length, topology, and signal-integrity requirements, although exact edge-rate and propagation-delay limits must be confirmed in the manufacturer datasheet. Typical uses include industrial automation links, building-automation equipment, instrumentation, motor-control systems, and industrial data networks. The device can also support point-to-point balanced links where continuous full-duplex operation is preferred. Companion interface devices such as the SN65HVD06D, SP485ECN-L, and SN75174DWR may be relevant when designing connected RS-485 networks or comparing transceiver families. A key design consideration is the absence of independent transmit and receive enables. PCB designers should therefore account for continuous driver activity and verify the driver state, bus termination, protection strategy, and cable topology against the system operating requirements. Decoupling, grounding, and differential-routing practices remain essential for reliable operation on externally accessible industrial buses. This page consolidates verified distributor listings, exact interface and packaging information, sourcing data, comparison fields, and practical design guidance. Where detailed electrical limits or a verified pin mapping were not present in the supplied source data, the missing information is explicitly identified rather than estimated.

Запрос цены Контакты
ISL8489IB-T - 5V RS-485/RS-422 Transceiver | Renesas Electronics
ISL8489IB-T

ISL8489IB-T - 5V RS-485/RS-422 Transceiver | Renesas Electronics

Renesas Electronics ISL8489IB-T is a 5 V, low-power RS-485/RS-422 interface transceiver packaged in a 14-pin SOIC. The device combines a full RS-485/RS-422 transceiver with low-power operation and supports high-speed or slew-rate-limited communication. Its 5 V supply and 14-pin surface-mount package suit compact industrial, instrumentation, and embedded data-link designs. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals to and from balanced differential pairs. In the RS-485 hierarchy, it connects a host controller or programmable logic device to a field bus. RS-422 provides a point-to-point differential link, while RS-485 supports multipoint bus arrangements subject to proper termination, biasing, and topology. The ISL8489IB-T is identified as a one-driver, one-receiver full transceiver for both RS-422 and RS-485 operation. Its 5 V operating supply supports integration with conventional low-voltage digital logic. The manufacturer describes the family as low-power and usable in high-speed or slew-rate-limited networks, allowing designers to select edge rates suited to their cable length, topology, and signal-integrity requirements. A balanced interface reduces sensitivity to common-mode noise relative to single-ended signaling. This makes the device applicable to industrial control links, data acquisition systems, building automation equipment, and communications equipment operating near motors, relays, power converters, or long external cables. The relevant data rate, driver strength, receiver thresholds, and propagation delays must be confirmed in the manufacturer datasheet before finalizing a high-speed link. The 14-pin SOIC package provides a standard surface-mount footprint suitable for automated assembly. Because RS-485 and RS-422 links depend on board-level implementation, layout should preserve the relationship between the transceiver, protection components, connector, and return path. Correct termination, fail-safe biasing, isolation strategy, and ESD protection are as important as the IC selection. For each RS-485 port, verify the supply voltage, logic thresholds, maximum data rate, driver and receiver enable behavior, thermal conditions, and package pin assignments against the manufacturer datasheet. Pay particular attention to whether a termination resistor is already integrated or must be added externally, and whether the receiver output remains defined when the bus is idle. This page organizes the exact ISL8489IB-T identity, technical specifications, interface-use guidance, source links, and design considerations. It also distinguishes confirmed device facts from parameters that require direct verification in the manufacturer datasheet before high-volume PCB release or production qualification.

Запрос цены Контакты
ISL8489IP - 5V 250kbps Full-Duplex RS-485/422 | Renesas
ISL8489IP

ISL8489IP - 5V 250kbps Full-Duplex RS-485/422 | Renesas

Renesas Electronics ISL8489IP is a 5 V, low-power, full-duplex RS-485/RS-422 transceiver capable of operation at 250 kbps and packaged in a 14-pin PDIP. The device combines one driver and one receiver in a single package, supports balanced differential communications, and provides a slew-rate-limited alternative for systems that require reduced signal-edge velocity. Its operating characteristics are suited to industrial, instrumentation, communications, and embedded data-acquisition equipment that must connect a host or controller to a balanced bus. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and converts received differential signals back into logic levels. RS-485 supports multipoint bus communication over long cable runs, while RS-422 commonly supports point-to-point and one-driver topologies. A full-duplex transceiver provides separate paths for transmitting and receiving, unlike half-duplex designs that share a bus and require direction-control logic. The ISL8489IP therefore fits designs that need simultaneous bidirectional communication without sharing a physical signal pair. Key verified features include a 5 V supply requirement, a maximum signaling rate of 250 kbps, full-duplex operation, support for both RS-485 and RS-422, low-power operation, and a slew-rate-limited operating option. The 14-pin PDIP package also provides through-hole compatibility for equipment requiring sockets, prototyping, or manually assembled industrial control boards. The indexed descriptions do not specify separate receiver-enable or transmitter-enable controls, indicating that this version is intended for continuous full-duplex operation. The transceiver architecture provides differential signaling, which is valuable in environments containing industrial machinery, switching supplies, and long interconnects. Differential voltage is measured between the two conductors of a pair rather than relative to ground, improving noise immunity on the receive side. The 250 kbps rate is appropriate for low-to-moderate-speed control and monitoring links where higher signaling rates are unnecessary. The slew-rate-limited behavior can help reduce edge-related ringing and electromagnetic interference when implemented with a correctly terminated network. Typical applications include industrial sensor and actuator networks, factory equipment links, building-control interfaces, laboratory instrumentation, point-to-point data links, and RS-422-compatible control systems. In these systems, the transceiver can connect a UART or microcontroller serial port to a balanced bus. Designers should still verify cable length, topology, grounding, termination, and logic-level compatibility against the complete system requirements before production release. A key design consideration is that the 14-pin PDIP package is not as compact as a surface-mount transceiver. It nevertheless simplifies through-hole construction and socket-based maintenance. The principal engineering trade-off is between 250 kbps operation, low power, full-duplex behavior, and the practical size and assembly requirements of a 14-pin through-hole package. This page consolidates the verified distributor and manufacturer-datasheet indexing information for the ISL8489IP with product-specific engineering guidance, specification gaps, and a transparent replacement assessment. It does not infer unseen electrical limits or substitute candidates whose pin compatibility has not been demonstrated.

Запрос цены Контакты
ISL8490IB - 5V Low-Power RS-485/RS-422 Transceiver | Renesas
ISL8490IB

ISL8490IB - 5V Low-Power RS-485/RS-422 Transceiver | Renesas

Renesas ISL8490IB is a 5V, low-power RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It is designed for balanced serial data links that require the physical signaling characteristics of both RS-485 and RS-422 interfaces. The verified source material identifies the ISL8490 as a single transceiver supporting high-speed operation or slew-rate-limited operation, allowing it to suit point-to-point RS-422 links as well as multipoint RS-485 networks when used with appropriate bus termination and biasing. Its interface role places it within the transceiver and line-driver hierarchy of communication interface ICs. An RS-485 transceiver converts logic-level digital information into differential signals suitable for balanced industrial communication cables. Differential signaling provides resistance to common-mode noise and allows communication over longer cable runs than a single-ended interface. An RS-422 transceiver similarly uses differential signaling, normally in a point-to-point topology. The ISL8490IB therefore serves as an interface between a digital controller or host and physical copper wiring while placing the high-voltage, high-current bus activity on the transceiver side of the circuit. The principal verified feature is its 5V supply operation. This places it among low-voltage CMOS interface devices intended for systems with compatible digital logic rails. The part is described as low power and as supporting either high-speed or slew-rate-limited communication. High-speed operation prioritizes data throughput, while slew-rate limiting reduces transition-edge energy and can help control electromagnetic interference and ringing on slower networks. Exact data-rate, supply-current, differential-output, input-threshold, and temperature-range values must be confirmed in the manufacturer datasheet before a design is released. Typical uses include industrial RS-485 links, point-to-point RS-422 interconnects, instrumentation, factory automation, building controls, and embedded communication networks. In each case, the transceiver is placed between the controller UART or logic interface and the A/B differential pair. Appropriate cable routing, common-mode grounding, surge protection, termination, and fail-safe biasing remain important parts of the complete interface. Designers should preserve the exact pin mapping and verify the required driver-enable, receiver-enable, termination, and exposed-pad details against the ISL8490 manufacturer datasheet. This page consolidates verified product identity, package information, source links, application guidance, and engineering considerations that are not presented together on a basic distributor listing.

Запрос цены Контакты
ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas
ISL8490IB-T

ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8490IB-T is a 5 V, single-channel RS-485/RS-422 transceiver built with BiCMOS technology and supplied in an 8-pin SOIC package. It combines one driver and one receiver in one package, supports both RS-485 and RS-422 balanced communication, and provides a low-power interface for industrial and instrumentation links. The device is designed for applications requiring either high-speed operation or slew-rate-limited signaling. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives differential signals back into logic-level outputs. RS-485 supports multipoint, half-duplex buses and is widely used in industrial automation, while RS-422 supports point-to-point and multidrop balanced links. The ISL8490IB-T belongs to the interface-IC hierarchy as a physical-layer communication device between a host controller and a balanced physical layer. The principal device characteristics include a 5 V supply, a 1/1 driver-to-receiver configuration, full RS-422 and RS-485 operation, low power consumption, and either high-speed or slew-rate-limited performance. These features make the device useful when a compact interface must support balanced differential signaling in a small PCB footprint. Its 8-pin SOIC construction also simplifies assembly and inspection on both through-hole-compatible boards and mixed-technology assemblies. BiCMOS implementation combines bipolar and CMOS characteristics within the interface circuit. In this transceiver family, that architecture supports low-power operation while preserving the drive and receive performance needed for balanced communication links. The manufacturer describes the ISL8490 series as devices specified for operation across a 10% supply variation around 5 V, allowing design attention to remain focused on interface margins and system-level power behavior. Typical uses include industrial sensor buses, factory automation equipment, process-control interfaces, building-control networks, and communications ports that connect a UART or controller to an RS-485 or RS-422 cable. In half-duplex RS-485 systems, driver-enable control can determine the bus direction. In full-duplex RS-422 systems, the driver and receiver can remain active without contention because the two channels use separate differential pairs. PCB design should preserve the symmetry of each differential pair, provide a continuous ground reference, and route the balanced lines away from clocks, switching nodes, and other high-current paths. Decoupling capacitors should be placed close to the supply and ground pins. External termination and biasing remain application-dependent and should be configured from the cable length, topology, node count, and driver state rather than added indiscriminately. This product overview combines the device identity, RS-485/RS-422 application context, package information, and practical implementation guidance. It is designed to help engineers identify the correct transceiver function and plan a robust balanced-communication layout without conflating protocol requirements, termination practice, and device-level capabilities.

Запрос цены Контакты
ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas
ISL8490IBZ

ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas

The Renesas Electronics ISL8490IBZ is a 5 V, full-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin SOIC package. It provides one balanced driver and one balanced receiver, supports a 4.5 V to 5.5 V supply range, and presents a single unit load to an RS-485 bus. The device is configured for full-duplex communication with separate transmit and receive paths. An RS-485/RS-422 transceiver is an interface integrated circuit that converts between single-ended logic signals and differential balanced-line signals. Differential signaling improves noise immunity and allows reliable communication over longer cables or higher-noise industrial environments. The transceiver category belongs to interface ICs within the broader semiconductor hierarchy and is commonly used for multidrop industrial buses, point-to-point links, instrumentation, and building-control networks. Key characteristics include a 5 Mbps maximum data rate, BiCMOS operation, full-duplex configuration, and operation from a 4.5 V to 5.5 V supply. The ISL8490IBZ is designed for systems that require separate differential transmit and receive lines. Its single-unit-load bus loading allows it to participate in conventional RS-485 networks while reducing the number of nodes permitted by a higher unit-load device. The electrical architecture uses a differential driver for balanced bus outputs and a differential receiver for detecting small logic-level voltages. Receiver and driver-enable inputs support local control of bus direction and receiver state. Because the part provides separate transmit and receive paths, no multidrop half-duplex direction-control multiplexing is required, which simplifies full-duplex point-to-point and dual-bus designs. Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, RS-422-compatible equipment, and isolated or non-isolated communication modules. The 5 Mbps capability is suitable for data links above the slower rates commonly associated with legacy RS-485 systems, while the 8-pin SOIC footprint supports compact board construction. When laying out the circuit, route the differential pair as a tightly coupled pair with continuous ground reference, terminate the far end of each differential bus, and keep transceiver switching and protection circuitry away from sensitive receive nodes. Confirm that the selected termination, protection, isolation, and connector strategy preserves the signal integrity required at the intended data rate and cable length.

Запрос цены Контакты
ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8490IP

ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8490IP is a 5 V, low-power, full-duplex RS-485 and RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and an 8-pin PDIP package. The device supports both high-speed RS-485 communication and RS-422 point-to-point links, while its separate receiver and driver enable paths provide flexibility for half-duplex control through the DE and RE inputs. Its operating-temperature range is -40°C to +85°C, making it suitable for industrial and commercial equipment requiring a through-hole interface solution. A transceiver is an interface IC that converts digital logic signals into balanced differential signals for reliable communication over noisy or long cable runs. In the hierarchy, the ISL8490IP is a line transceiver, a type of interface IC and communications semiconductor. RS-485 supports multiple drivers and receivers on a shared bus, whereas RS-422 commonly uses a dedicated driver and receiver for point-to-point or multidrop networks. This transceiver supports both protocols and therefore provides a useful interface between CMOS/TTL logic and balanced cabling. The verified headline specifications are a 5 V supply, 5 Mbps maximum data rate, 70 mV receiver hysteresis, 1 driver, 1 receiver, full-duplex operation, and support for RS-422 and RS-485. These parameters place the part in the low-power, high-speed or slew-rate-limited transceiver category described by the manufacturer documentation. The 8-pin PDIP format also permits conventional through-hole PCB assembly rather than requiring a fine-pitch surface-mount land pattern. Technically, the balanced driver and receiver provide noise immunity over longer interconnects than ordinary single-ended logic. Receiver hysteresis helps distinguish signaling states in the presence of noise, while the 5 Mbps capability supports communication rates beyond the slow speeds commonly used by legacy RS-485 systems. Because the exact input capacitance, output timing, supply-current limits, and slew-rate settings are not included in the supplied verified excerpts, design engineers should confirm them in the manufacturer datasheet before finalizing timing, termination, and decoupling. Typical uses include industrial controllers, building automation equipment, data acquisition systems, instrumentation, industrial networking equipment, and embedded control links. For an RS-485 bus, the circuit requires suitable line termination and biasing. For RS-422, driver and receiver connections should follow the source and destination topology specified by the system architecture rather than being treated as a multi-drop RS-485 bus. The principal design consideration is signal integrity at 5 Mbps. Layout should minimize the distance between the transceiver, protection devices, connector, and differential pair, while keeping the two conductors of each balanced pair closely coupled. Decoupling close to the supply pin, controlled ground return paths, and appropriate surge protection help maintain reliable operation in industrial environments. This page consolidates the verified distributor and manufacturer-document information with lifecycle status, procurement guidance, application fit, package details, and honest replacement limitations. It distinguishes confirmed facts from specifications that still require verification from the full Renesas datasheet.

Запрос цены Контакты
ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas
ISL8491EIB

ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas

The Renesas ISL8491EIB is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver with ±15kV ESD protection, slew-rate-limited high-speed operation, and separate receive and transmit output-enable pins. It is packaged in a 14-lead SOIC and is designed for industrial communication links requiring both differential transmit and differential receive capability. An RS-485/RS-422 transceiver is an interface IC that converts digital logic signals into balanced differential signals and receives differential signals from a cable. These differential signaling methods improve noise immunity and allow reliable data transmission over longer cable distances than single-ended interfaces. The ISL8491EIB supports both RS-485 and RS-422 operating modes, while its full-duplex arrangement permits simultaneous transmission and reception when the bus wiring and termination network are configured appropriately. The main device characteristics are a 5V supply, ±15kV ESD protection, low-power operation, high-speed communication with slew-rate limiting, and separate receive and transmit output-enable pins. The separate enables allow the transmitter and receiver to be controlled independently, which is useful in multidrop RS-485 networks where a node must listen while preventing bus contention. The 14-lead SOIC package is a standard surface-mount format compatible with conventional PCB assembly methods. The ISL8491EIB is based on the Renesas ISL8491E family, which is positioned for robust industrial data links. ESD protection is particularly important because RS-485 interfaces are commonly exposed to user-accessible cables and connector transients. Slew-rate limiting helps control edge transitions on the bus and reduce unwanted high-frequency content, while the low-power design supports systems where standby and active-state efficiency are important. The exact data rate, receiver thresholds, common-mode limits, and supply-current limits should be confirmed in the manufacturer datasheet before final design release. Typical applications include industrial automation controllers, factory data buses, building automation equipment, instrumentation links, motor-control systems, and embedded serial interfaces. The full-duplex architecture is especially appropriate for point-to-point RS-422 links and full-duplex RS-485 networks where transmit and receive paths operate simultaneously. Independent enables can support bus segmentation, controlled test modes, or systems that need to mute a receiver during certain operating states. Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, particularly for enable inputs, ground connections, driver outputs, and receiver inputs. The external network must include appropriate termination, biasing, protection, and decoupling components for the selected RS-485 or RS-422 topology. Confirm the exact ISL8491EIB ordering code, package marking, and operating-temperature limits before production release. This page consolidates the available ISL8491EIB product information, direct replacement options, package information, and practical interface-design guidance to support faster component evaluation and sourcing decisions.

Запрос цены Контакты
ISL8491IB - 5V RS-485/RS-422 Transceiver | Renesas
ISL8491IB

ISL8491IB - 5V RS-485/RS-422 Transceiver | Renesas

Renesas Electronics ISL8491IB is a 5V, low-power, full-duplex RS-485/RS-422 transceiver integrated circuit in a 14-pin SOIC package. It combines one driver and one receiver in a single balanced-communications device, providing the core physical-layer functions required for point-to-point RS-422 links and multipoint RS-485 buses. The verified manufacturer and distributor records identify the device as a 14-SOIC, full-duplex RS-485/RS-422 transceiver with high-speed or slew-rate-limited operation. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and reconstructs logic-level data from those differential signals. The differential signaling belongs to the transceiver class within interface ICs, data communications, and the broader semiconductor hierarchy. Balanced operation improves noise immunity by deriving the received state from the voltage difference between two conductors rather than relying on a signal measured relative to ground alone. The principal identified features of the ISL8491IB are its 5V CMOS-style supply operation, low-power architecture, full-duplex configuration, and support for both RS-485 and RS-422 communication standards. Because it contains one transmitter and one receiver, the part can support simultaneous transmit and receive paths when the host or controller provides separate request and data-bus signals. The verified distributor description also identifies variants capable of high-speed or slew-rate-limited operation, allowing engineers to compare communication behavior and system timing requirements. The ISL8491IB is suitable for industrial data links, industrial automation equipment, instrumentation, building-control networks, and embedded systems that exchange data over balanced copper cabling. Its 14-pin SOIC package supports conventional surface-mount PCB assembly, while the full-duplex arrangement avoids sharing one physical pair between opposing directions. Designers must still provide suitable logic interfacing, termination, biasing, grounding, and protection appropriate to the cable length, data rate, and industrial environment. A critical design consideration is that the transceiver's communication mode and electrical settings must match the network topology. RS-422 generally supports a point-to-point driver relationship, while RS-485 permits multiple drivers on a bus but requires careful idle-state biasing and termination. The exact driver strength, receiver thresholds, data rate, common-mode range, ESD rating, and pin-level truth table are not supplied in the verified data and should be confirmed in the manufacturer datasheet before layout or production use. This page consolidates the verified distributor and manufacturer references for the ISL8491IB, distinguishes the device from general-purpose interface ICs, and provides sourcing, selection, replacement, and application guidance. It also records uncertain specifications explicitly rather than substituting estimates, helping engineers make an informed first-stage decision before validating the complete electrical limits and pin configuration.

Запрос цены Контакты
ISL8491IB-T - 5V RS-485/RS-422 Transceiver | Renesas
ISL8491IB-T

ISL8491IB-T - 5V RS-485/RS-422 Transceiver | Renesas

Renesas ISL8491IB-T is a single RS-485 and RS-422 transceiver operating from a 5 V supply and supporting data rates up to 5 Mbps. The device is offered in a 14-pin SOIC package and combines one driver and one receiver in a single integrated circuit. Its RS-485/RS-422 interface capability, low-power BiCMOS implementation, and slew-rate-limited operation make it suitable for balanced industrial communication links that require compact signal conditioning. A transceiver is an interface IC that converts logic-level signals into differential bus levels and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced communication, while RS-485 supports longer multipoint buses. The ISL8491IB-T places the balanced driver and receiver in one 14-SOIC package, reducing component count on communication interfaces that require both transmission and reception. The ISL8491IB-T operates from 5 V, supports communications through 5 Mbps, and includes ESD protection according to its product descriptions. Its slew-rate-limited behavior helps control the transition rate applied to the bus, which is important when reducing high-frequency harmonics and signal-integrity problems in cables, connectors, and long wiring. The 14-pin SOIC package supports conventional surface-mount assembly and is widely compatible with industrial control-board layouts. The device is based on a low-power, high-speed BiCMOS process. Combining bipolar and CMOS characteristics supports the interface requirements of a 5 V communication circuit while retaining the low-power characteristics expected in industrial equipment. The integrated driver-receiver arrangement simplifies bidirectional bus connections, although protocol direction control, termination, biasing, and isolation remain functions of the complete interface circuit. Typical uses include industrial automation controllers, factory data-collection equipment, building-control gateways, instrumentation, and embedded RS-485 or RS-422 ports. It can also serve as the physical-layer interface in systems that exchange commands and sensor data across a balanced bus. The 5 Mbps capability is relevant for factory and industrial links, while the slew-rate limiting should be considered when selecting cable length, topology, and termination. PCB design should follow the pin-description table in the manufacturer datasheet when assigning signal traces and supply connections. Keep the transceiver close to the bus connector, provide the required local supply decoupling, and place termination and fail-safe bias components where they can be reached without long stubs. Confirm the selected connector, cable, and grounding strategy against the communication standard used by the system. This product page combines the verified 5 V, 5 Mbps, RS-485/RS-422, ESD, BiCMOS, and 14-SOIC characteristics with practical interface-design guidance, sourcing information, and pin-compatible alternatives. It also helps engineers identify which details must still be confirmed in the manufacturer datasheet before schematic release or PCB sign-off.

Запрос цены Контакты
ISL8491IBZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8491IBZ

ISL8491IBZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8491IBZ is a 5 V, full-duplex, 1-transceiver/1-receiver RS-485/RS-422 interface IC operating at data rates up to 5 Mbps in a 14-pin SOIC package. It uses BiCMOS circuitry, accepts a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and includes an enable-controlled operating mode for interface management. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and printed-circuit-board interconnects. Within the product hierarchy, it is a transceiver within interface ICs and a communications interface device. RS-422 emphasizes point-to-point, full-duplex balanced links, while RS-485 supports multipoint buses and commonly uses a half-duplex arrangement. The ISL8491IBZ provides separate transmit and receive paths for full-duplex use. Key features include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply despite the nominal 5 V description, one-unit-load RS-485 bus loading, and support for both RS-485 and RS-422 signal environments. Its enable control can place the interface into a controlled state when the host does not require active communication. The 14-pin SOIC format is also used by the related ISL8490 and ESD-protected ISL8491E devices. The BiCMOS implementation combines bipolar and CMOS characteristics to support high data rates in a single 5 V transceiver. Full-duplex topology separates the differential transmitter outputs from the differential receiver inputs, allowing transmission and reception to operate simultaneously. The 5 Mbps capability makes the device suitable for moderately high-speed industrial links, while the single-unit-load bus characteristic helps control loading when multiple nodes share an RS-485 network. Typical applications include industrial automation equipment, factory data buses, industrial sensor interfaces, building-control networks, test and measurement systems, and embedded communications equipment. The device can also support full-duplex RS-422 point-to-point links between controllers and remote peripherals. System-level protocol framing, bus termination, grounding, and protection must still be designed around the cable environment. Designers should use the manufacturer's pin-description table when assigning signals and should provide the supply decoupling recommended by the ISL8485, ISL8490, and ISL8491 datasheet. Differential routing should use a controlled-impedance PCB stack-up, with closely matched trace lengths and uninterrupted ground references helping reject common-mode noise. This product page consolidates the obsolete lifecycle status, RS-485/RS-422 operating characteristics, drop-in family options, package details, and practical interface-design guidance into a focused engineering reference for legacy and redesign evaluations.

Запрос цены Контакты
ISL8491IP - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL8491IP

ISL8491IP - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL8491IP is a 5 V, low-power RS-485/RS-422 line transceiver with one driver and one receiver, full-duplex operation, a maximum data rate of 5 Mbps, and a 14-pin PDIP package. The device combines differential RS-485 and RS-422 communication support in a single integrated circuit, making it suitable for industrial data links, instrumentation, and point-to-point balanced communication systems. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential balanced signals for reliable data transmission over cables. These differential signaling methods are members of the broader interface-controller category, connect digital systems to physical communication links, and provide improved noise immunity compared with single-ended logic interconnects. The ISL8491IP supports both protocols, allowing equipment designers to select the appropriate termination and biasing arrangement for the cable and system topology. The verified part data identifies a 4.5 V to 5.5 V supply range, 5 Mbps maximum data rate, 70 mV receiver hysteresis, one transmitter, one receiver, full duplex, and an operating temperature range of -40°C to 85°C. These characteristics suit industrial equipment operating near a regulated 5 V rail and requiring communication speeds up to 5 Mbps. The through-hole PDIP-14 package is also appropriate for leaded PCB designs where a small surface-mount land pattern is not required. The ISL8491IP is listed as obsolete in the verified source data. Consequently, engineers should not assume that new production procurement is available and should confirm lifecycle status, traceability, and last-time-buy opportunities directly with the manufacturer or an authorized distributor. Renesas Electronics Corporation is the listed supplier, while the original documentation is associated with Intersil Corporation. Typical uses include industrial control links, factory automation equipment, remote sensor interfaces, RS-422 point-to-point links, and test-and-measurement systems. In these applications, the device separates the logic domain from the noisy cable environment through differential transmission and reception. Cable length, data rate, termination, common-mode range, and grounding remain system-level constraints that must be evaluated separately from the integrated circuit specifications. A practical design step is to preserve the transmitter enable and receiver enable control paths, place termination only where required by the cable topology, and provide a stable 5 V supply close to the device. Since the verified sources do not provide a complete pin table, absolute maximum ratings, output current, or detailed electrical characteristics, those values should be confirmed in the manufacturer datasheet before final release. This page combines verified distributor and datasheet information with lifecycle, sourcing, application, and design guidance. It also distinguishes verified facts from parameters that still require manufacturer-document confirmation, helping engineers evaluate the ISL8491IP without confusing an obsolete status with an interchangeable modern replacement.

Запрос цены Контакты
ISL8499IR - 0.24 Ohm Low-Voltage Quad SPDT Switch | Renesas
ISL8499IR

ISL8499IR - 0.24 Ohm Low-Voltage Quad SPDT Switch | Renesas

The Renesas Electronics ISL8499IR is a low-voltage, bidirectional, quad SPDT analog switch housed in a 16-pin QFN package. It operates from a single +1.65 V to +4.5 V supply, with an on-resistance of 0.24 ohm at +4.3 V, 0.26 ohm at +3.0 V, and 0.45 ohm at +1.8 V. Switching times are 15 ns for tON and 13 ns for tOFF, making the device suitable for battery-powered equipment requiring low resistance and rapid signal selection. An analog switch is an integrated semiconductor that routes analog signals between external nodes under digital control. The ISL8499 contains two independent dual-pole, double-throw switching functions, commonly described as a quad SPDT or dual DPDT device. Within the interface IC and analog-switch hierarchy, its low-voltage operation, bidirectional signal path, and low power consumption are particularly useful for portable audio, test, communication, and battery-operated measurement systems. The principal electrical features include a +1.65 V to +4.5 V single-supply range, low on-resistance across multiple supply voltages, and on-resistance matching between channels of 0.04 ohm. The verified datasheet information also reports on-resistance flatness across the signal range of 0.05 ohm. These characteristics help reduce insertion loss and channel-to-channel resistance variation when routing sensitive analog signals. The device is designed for 1.8 V-compatible logic when operated from a +3 V supply. With a +4.2 V supply and 2.85 V logic-high inputs, the maximum supply current is 10 microamperes. Power dissipation is reported below 0.2 microwatts under the stated low-power conditions, supporting the use of the ISL8499IR in battery-powered equipment where leakage and standby consumption can affect the usable runtime. Typical applications include routing audio signals in portable equipment, selecting sensor inputs in test and measurement systems, multiplexing communication channels, and switching low-voltage analog signals in battery-operated instruments. The 15 ns tON and 13 ns tOFF characteristics support fast system reconfiguration, while the low on-resistance limits signal attenuation across the selected channel. Designers should verify control-logic levels against the selected supply voltage and ensure that switched signals remain within the device's supported analog-signal range. The exposed thermal pad and exposed-pad construction also require a suitable PCB land pattern and adequate copper for heat spreading, particularly when continuously routing signals at higher frequencies or temperatures. This page consolidates the verified Renesas product information, source-linked pricing and lifecycle references, explicitly identified drop-in relationships, and practical selection guidance. It also separates documented performance from parameters that still require confirmation from the complete manufacturer datasheet or a specific distributor record.

Запрос цены Контакты
ISL8499IRZ - Ultra-Low On-Resistance Quad SPDT Switch | Renesas
ISL8499IRZ

ISL8499IRZ - Ultra-Low On-Resistance Quad SPDT Switch | Renesas

The Renesas ISL8499IRZ is a low-voltage, bidirectional quad SPDT analog switch, also described as a dual DPDT switch, designed for single-supply operation from +1.65 V to +4.5 V. It is packaged in a 16-pin QFN package measuring 3 x 3 mm. The device provides four switch circuits in a 2:1 configuration, making it suitable for routing low-voltage analog signals in compact, battery-powered, and portable equipment. An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. The ISL8499IRZ family combines low ON-resistance, fast switching, low power consumption, and 1.8 V-compatible logic operation. Its low ON-resistance is intended to minimize signal attenuation and distortion when the switch is closed, while the fast switching speeds support higher-bandwidth signal routing. The bidirectional architecture allows signal flow in either direction through each selected switch path. The principal electrical features include ultra-low ON-resistance, with manufacturer cross-reference information listing 0.24 ohm at V+ = 4.3 V and 0.26 ohm at V+ = 3.0 V. The device also has a stated ON-resistance of 0.45 ohm at V+ = 1.8 V, ON-resistance matching between channels of 0.04 ohm, and ON-resistance flatness across the signal range of 0.05 ohm. Switching timing is listed as 15 ns for turn-on and 13 ns for turn-off. The ISL8499IRZ is designed around a low-voltage, single-supply architecture intended for battery-powered systems and other compact applications. Its specified operating temperature range is -40 C to +85 C. The 16-QFN (3 x 3) package provides a small board footprint for space-constrained designs, while the quad SPDT arrangement allows multiple independent or mutually exclusive signal connections to be controlled from a small number of control inputs. Typical uses include portable measurement equipment, battery-operated test instruments, analog signal conditioning, communication interfaces, and compact embedded systems. In these applications, the switch can select between external signals, route a signal toward an amplifier or converter, or isolate a measurement path during a test sequence. The low ON-resistance helps preserve signal amplitude, while the fast switching performance can reduce timing overhead in repeated routing operations. PCB implementation should follow the manufacturer pin and land-pattern guidance, paying particular attention to exposed-pad soldering and the control-logic levels. The 1.8 V-compatible control inputs allow operation from low-voltage digital systems, but the logic thresholds and supply sequencing must still be checked against the final system requirements. The short 3 x 3 mm package also requires careful placement of power and ground connections to minimize parasitic inductance and maintain clean analog signal behavior. This product page combines the manufacturer switching characteristics, package information, cross-reference guidance, and practical design considerations for engineers evaluating the ISL8499IRZ. It is intended to support footprint compatibility checks, signal-integrity planning, sourcing decisions, and early schematic and layout reviews.

Запрос цены Контакты
ISL8499IV - Ultra Low ON-Resistance Quad SPDT Switch | Renesas
ISL8499IV

ISL8499IV - Ultra Low ON-Resistance Quad SPDT Switch | Renesas

The Renesas Electronics ISL8499IV is an ultra-low ON-resistance, bidirectional Quad SPDT analog switch, also described as a dual DPDT switch, for single-supply operation from +1.65 V to +4.5 V. The device is supplied in a 16-TSSOP package and is intended for low-voltage signal-routing applications, including battery-powered equipment. Its listed ON resistance is approximately 250 mOhm in distributor product data, while the manufacturer-oriented description identifies 0.24 Ohm ON resistance at a +4.3 V supply and 0.26 Ohm at +3.0 V. The switch also provides fast switching behavior, with tON and tOFF values reported in the Intersil datasheet excerpt as 15 ns and 13 ns respectively. Digital logic inputs are described as 1.8 V logic-compatible when the device is operated from a single +3 V supply. The ISL8499IV is a bidirectional analog switch, so its signal paths can be routed in either direction, making it suitable for multiplexed sensor, measurement, communication, and low-voltage analog systems. It is identified by Renesas as a pin-compatible drop-in replacement for the STG3699 and DG2799, according to the supplied cross-reference material. This page combines manufacturer identification, distributor specifications, cross-reference information, practical design notes, and a parameter comparison to support sourcing and engineering decisions. Pricing shown below is referenced to the current verification date, while unverified details are explicitly marked for follow-up rather than inferred.

Запрос цены Контакты
ISL8499IVZ - Quad SPDT Low-RON Switch | Renesas Electronics
ISL8499IVZ

ISL8499IVZ - Quad SPDT Low-RON Switch | Renesas Electronics

The Renesas Electronics ISL8499IVZ is a bidirectional quad SPDT analog switch, also described as a dual DPDT device, with four switch circuits configured as 2:1 multiplexers in a 16-pin TSSOP package. It operates from a single +1.65 V to +4.5 V supply and provides a typical ON resistance of 0.24 ohm at a 4.3 V supply. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The ISL8499 belongs to the analog switch and multiplexer hierarchy within interface integrated circuits. Its low-voltage, low-resistance design is intended to minimize signal loss when connecting battery-powered sensors, audio paths, test equipment, or portable measurement systems. Four independently controlled SPDT poles provide flexible routing in compact systems. Key features include an ON resistance of 0.26 ohm at 3.0 V and 0.45 ohm at 1.8 V. Typical switching times are 15 ns for turn-on and 13 ns for turn-off. The manufacturer identifies 1.8 V logic compatibility for single-supply operation, while channel-to-channel ON-resistance matching is 0.04 ohm and ON-resistance flatness across the signal range is 0.05 ohm. The device uses a compact analog-switch architecture to provide low resistance with fast transitions. Each SPDT circuit can connect one common terminal to one of two selectable terminals, allowing the four circuits to implement paired signal routing, source selection, or dual-DPDT switching. The manufacturer highlights low power consumption below 0.2 microwatt and suitability for battery-powered equipment where every switching action must avoid unnecessary signal degradation. Typical applications include portable audio routing, battery-operated sensor interfaces, precision test and measurement systems, handheld instrumentation, and low-voltage communication equipment. The combination of a 1.65 V minimum supply, 1.8 V-compatible control inputs, sub-20 ns switching timing, and low channel matching supports systems that route small-amplitude signals while operating from limited power budgets. A key design consideration is the relationship between supply voltage and ON resistance. Resistance rises from 0.24 ohm at 4.3 V to 0.45 ohm at 1.8 V, so designs operating close to the minimum supply should be reviewed for insertion loss. Control-signal levels, unused pins, and switch-state transitions must also be checked against the manufacturer pin-description and timing information before layout release. This page combines manufacturer specifications, verified same-footprint cross-references, practical routing guidance, and application-focused design considerations. It supports faster part evaluation by presenting electrical behavior, replacement constraints, and layout implications together rather than reproducing basic catalog information alone.

Запрос цены Контакты
ISL8563CB - 2/2 RS-232 Transceiver, 250kbps | Renesas
ISL8563CB

ISL8563CB - 2/2 RS-232 Transceiver, 250kbps | Renesas

The Renesas ISL8563CB is a 2/2 RS-232 transceiver IC with a 3 V to 5.5 V single supply, a guaranteed minimum data rate of 250 kbps, and 1 microamp low-power operation in an 18-pin SOIC package. It combines two transmitters and two receivers on one die, allowing a compact implementation of bidirectional serial-interface ports while meeting EIA/TIA-562 and EIA/TIA-232 specifications. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 physical link. The transmitter converts low-voltage digital signals into RS-232-level voltages, while the receiver converts the bipolar RS-232 input back into a logic-compatible signal. Within the broader hierarchy, this device is a line-driver and receiver interface IC used to bridge digital systems with RS-232 equipment. The ISL8563CB operates from a single +3 V to +5.5 V supply, including the lower-voltage condition identified in the verified datasheet description. Its low-power operation is specified at 1 microamp, making it relevant to portable and space-constrained systems where standby consumption matters. The guaranteed 250 kbps minimum data rate supports common serial-control, point-of-sale, industrial-interface, and legacy peripheral connections without requiring a separate high-speed transceiver. The device requires only four external 0.1 microfarad capacitors according to the verified manufacturer-datasheet description. This small external-component count simplifies layout and reduces the number of placement and routing decisions around the interface. Because the ISL8563CB integrates two transmitters and two receivers, each channel direction can be implemented without duplicating the driver or receiver function in separate packages. Typical uses include RS-232 links in personal digital assistants, palmtop computers, notebook and laptop computers, embedded control systems, and industrial data-acquisition equipment. The same device can also support service-console, configuration-port, and point-of-sale interfaces where an EIA/TIA-232-compatible physical layer is required but board area and standby power are constrained. Designers should verify signal levels, grounding, cable length, and system requirements against the manufacturer datasheet before replacing a discrete RS-232 implementation. The four external 0.1 microfarad capacitors should be placed close to their associated device pins, while supply and ground planes should provide a low-impedance return path. Because the verified data does not provide a complete 18-pin mapping, the package drawing and pin definitions must be checked against the datasheet before PCB release. This page consolidates the verified supply, speed, power, package, standard-compliance, pricing, and sourcing information for ISL8563CB and adds practical application guidance. It also explicitly distinguishes verified facts from parameters that remain unavailable in the supplied data, including detailed pin definitions, temperature limits, and confirmed drop-in substitute MPNs.

Запрос цены Контакты
ISL8563CP - 250kbps RS-232 Transceiver | Renesas
ISL8563CP

ISL8563CP - 250kbps RS-232 Transceiver | Renesas

Renesas ISL8563CP is a dual RS-232 transmitter and receiver interface IC operating from +3 V to +5.5 V at data rates up to 250 kbps, with a low operating supply current of 1 µA and an 18-pin PDIP package. The device is designed for portable and embedded systems that require bidirectional serial communication using the RS-232 electrical interface. An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232-compatible levels, then restores received RS-232 signals to logic levels for a host, controller, or peripheral. The ISL8563CP belongs to the interface IC category and combines two transmitters and two receivers in one package, providing bidirectional communication over two data channels. Its documented headline characteristics include operation from +3 V to +5.5 V, 1 µA operating supply current, and a maximum data rate of 250 kbps. The indexed datasheet states that the transmitters and receivers meet EIA/TIA-232 and EIA/TIA-562 specifications even when the supply voltage is 3.0 V. These characteristics suit equipment where low voltage compatibility and reduced supply demand are important. The ISL8563CP contains two complete transmit channels and two receive channels, allowing two simultaneous RS-232 links within one device. Unlike single-direction level-shifter blocks, this integrated arrangement reduces the component count required for a dual-port interface. Its 18-pin PDIP package is suitable for through-hole assembly and prototype or legacy system designs where a surface-mount package is unnecessary. Typical uses include RS-232 ports for personal digital assistants, palmtop computers, notebook and laptop computers, industrial control equipment, diagnostic interfaces, and embedded data-logging systems. A board designer can place the transceiver between a host UART and an external DB9 or other RS-232 connector, while observing the interface voltage, grounding, and protection requirements of the RS-232 environment. Designers should verify the logic levels, receiver thresholds, transmitter output levels, capacitance loading, and external protection requirements against the complete datasheet before production use. Because the verified results do not provide a complete pin table, exact pin names, temperature range, or recommended external network values, those details require confirmation from the original manufacturer documentation. The 1 µA operating-current figure should also be understood under its stated test conditions rather than assumed across every operating mode. This page consolidates the verified distributor indexing, package information, interface standards, operating limits, and application guidance for the ISL8563CP. It also distinguishes confirmed technical facts from unavailable details and avoids presenting unverified drop-in equivalents or fabricated pricing as authoritative purchasing data.

Запрос цены Контакты
ISL8563ECB - 3V RS232/RS562 Transceiver | Renesas | 18-SOIC
ISL8563ECB

ISL8563ECB - 3V RS232/RS562 Transceiver | Renesas | 18-SOIC

Renesas ISL8563ECB is a dual RS232 and RS562 transceiver operating from a 3.0 V to 5.5 V supply in an 18-pin wide SOIC package. The integrated circuit combines two transmitters and two receivers, supports operation at up to 5 Mbps, and provides ±15 kV electrostatic-discharge protection on the RS-562 transmitter outputs and receiver inputs according to the manufacturer datasheet. A transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a physical communications link. The ISL8563E belongs to the RS232 transceiver category, where a transmitter translates CMOS/TTL levels into RS232-compatible levels and a receiver performs the inverse conversion. Supporting both EIA/TIA-232 and EIA/TIA-562 operation lets the same device serve conventional RS232 links and lower-voltage, higher-noise-tolerant RS562 applications while remaining a 3 V-compatible interface IC. The principal operating features are a 3.0 V minimum supply, a 5.5 V maximum supply, two transmit channels, two receive channels, and 5 Mbps data-rate capability. Its broad supply range permits use in both 3.3 V and 5 V equipment. The manufacturer states that the transmitter and receiver circuits meet EIA/TIA-562 and EIA/TIA-232 specifications even when VCC is 3.0 V, providing design flexibility where the downstream system does not use a 5 V logic rail. The ISL8563ECB also provides ±15 kV ESD protection on exposed RS-562 pins using the IEC 61000-4-2 air-gap and human-body-model methods. This protection is important on cables that leave an enclosure because electrostatic discharge events can otherwise damage a transceiver input or output. The 18-SOIC package is 0.295 inches, or 7.50 mm, wide and remains suitable for conventional surface-mount PCB assembly. Typical applications include multi-drop industrial serial links, data acquisition equipment, instrumentation, POS terminals, industrial controllers, and communications interfaces requiring both RS232 and RS562 compatibility. In these systems, the device provides the electrical interface between a low-voltage digital controller and an external serial cable. Designers should select cable protection, grounding, and connector details for the installation because the IC cannot substitute for an earth-ground connection or complete surge-protection network. A key design consideration is that the 18-SOIC footprint has 18 leads and requires a sufficiently wide land pattern; the package should not be confused with a narrow 8-pin SOIC. Review the manufacturer pin-description table before assigning signal names, and observe the stated supply range, receiver enable or shutdown behavior, and output-slew requirements during PCB review. The exposed interface pins should be routed away from unprotected board edges when practical. This page organizes the verified technical characteristics, sourcing information, documented standards, and practical replacement considerations for engineers evaluating the ISL8563ECB. It also highlights the distinctions that matter when comparing this Renesas device with a 3.3 V RS562 transceiver in an 18-lead wide-SOIC package.

Запрос цены Контакты
ISL8563IB - 250kbps RS-232/RS-562 Transceiver | Renesas Electronics
ISL8563IB

ISL8563IB - 250kbps RS-232/RS-562 Transceiver | Renesas Electronics

The Renesas Electronics ISL8563IB is a 2-transmitter, 2-receiver RS-232 and RS-562 interface transceiver operating from a 3V to 5.5V supply at up to 250kbps, housed in an 18-pin SOIC package. The device provides approximately 1µA low-power operation and incorporates ESD protection rated at ±15kV, making it suited to compact battery-powered and portable serial interfaces. It is used for RS-232 and RS-562 data links in notebook computers, PDAs, palmtop computers, digital cameras, and other portable equipment. An RS-232 transceiver is an interface IC that combines voltage-level transmitters and receivers for unbalanced serial communication. It belongs to the driver, receiver, and transceiver hierarchy within interface ICs, converting logic-level signals into RS-232-compatible levels and reconstructing received logic signals. The RS-562 standard is referenced alongside EIA/TIA-232 and EIA/TIA-562, allowing the ISL8563 family to support both communication approaches where compatible with the system interface requirements. The ISL8563IB provides two transmit channels and two receive channels, supporting a complete dual-direction serial interface in one package. Its maximum data rate of 250kbps accommodates higher-speed legacy serial links, while the 3V to 5.5V supply range supports both 3V and 5V system rails. The approximately 1µA operating-current figure is particularly relevant to portable equipment where standby and overall battery consumption constrain the usable architecture. ESD protection of ±15kV strengthens the device against electrostatic discharge encountered during connector handling and field use. The 18-pin SOIC package also provides a conventional surface-mount option for RS-232 ports. Because the available verification data does not include the complete electrical tables, exact output levels, slew rates, receiver thresholds, and internal charge-pump details, designers should consult the manufacturer datasheet before finalizing timing, capacitance, and signal-integrity margins. Typical uses include serial ports in portable computers, PDAs, palmtop computers, digital cameras, battery-operated instruments, and other equipment requiring an RS-232 or RS-562 connection. In a portable design, the 3V-to-5.5V operating range permits connection to either rail, while the low 1µA operating-current characteristic supports power-conscious operation. Designers should still confirm whether the cited value applies to a specific mode or test condition in the datasheet. The primary design consideration is preserving adequate driver, receiver, and connector margins under the actual cable and load conditions. Place the transceiver close to the interface connector, provide the required bypass capacitance, observe the maximum supply voltage of 5.5V, and validate the complete channel with the intended cable length and baud rate. The available data does not provide a verified pin-by-pin mapping, so the package drawing and pin descriptions should be taken directly from the manufacturer datasheet. This product record consolidates the verified distributor specifications, package information, commercial availability, and practical selection considerations for the ISL8563IB. It also distinguishes verified facts from parameters that still require datasheet confirmation and explains why no unverified cross-brand substitute is presented as a guaranteed drop-in replacement.

Запрос цены Контакты
ISL8563IP - 3V-5.5V 250kbps RS-232 Interface | Renesas
ISL8563IP

ISL8563IP - 3V-5.5V 250kbps RS-232 Interface | Renesas

The Renesas Electronics ISL8563IP is a 3V-to-5.5V powered RS-232 transmitter/receiver interface IC with a guaranteed minimum data rate of 250kbps and 1uA-class operational supply current. The device is packaged as ISL8563IP in a leaded plastic-style package identified by the IP ordering code. It integrates RS-232 drivers and receivers intended for low-voltage serial links, with compliance stated for EIA/TIA-562 and EIA/TIA-232 operation, including operation down to a 3.0V supply. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, it belongs to the interface IC family, alongside line drivers, receivers, transceivers, and communications interface devices. The ISL8563IP specifically addresses systems that need bidirectional serial communication without using a 5V-only RS-232 implementation. Three headline characteristics make the ISL8563IP useful in compact equipment. Its 3.0V-to-5.5V operating supply supports both 3.3V and 5V system rails. Its guaranteed 250kbps minimum data rate permits substantially faster communication than conventional low-speed serial links. Its 1uA operational supply current supports power-conscious portable equipment. The manufacturer datasheet also states that only four external 0.1uF capacitors are required, simplifying the surrounding analog and digital interface circuitry. Technically, the device combines powered transmitters and receivers designed to meet EIA/TIA-562 and EIA/TIA-232 specifications. The dual-standard positioning is important because EIA/TIA-562 was developed for lower-voltage RS-232-compatible links, while EIA/TIA-232 describes conventional RS-232 electrical characteristics. The verified device description explicitly confirms operation at VCC = 3.0V, rather than requiring the 5V supply traditionally associated with classic RS-232 parts. Typical uses include PDAs, palmtop computers, notebook computers, and other portable or compact systems with low-voltage RS-232 links. The ISL8563IP is also appropriate for point-to-point serial connections, equipment interfaces, and embedded control links where the system supply is 3.3V or 5V. Its 250kbps capability can shorten communication time when the connected equipment and protocol support that rate. A key design consideration is that the external capacitors must be placed close to their associated device pins, and the board must maintain adequate separation between RS-232 driver outputs and receiver inputs to limit noise coupling. Designers should also verify that the connected equipment uses compatible signal levels and baud rates. The verified material does not expose the complete pin assignment, so the published package drawing should be consulted before PCB routing. This product record combines verified electrical capabilities, sourcing information, availability data, and application guidance in one engineering-oriented reference. It also clearly distinguishes confirmed manufacturer specifications from unavailable details rather than estimating pin assignments, package dimensions, temperature limits, or lifecycle details.

Запрос цены Контакты
ISLA212P20IRZ - 12-Bit 200MSPS SAR ADC, 72-QFN | Renesas
ISLA212P20IRZ

ISLA212P20IRZ - 12-Bit 200MSPS SAR ADC, 72-QFN | Renesas

The Renesas (formerly Intersil) ISLA212P20IRZ is a 12-bit, 200 MSPS successive-approximation-register (SAR) analog-to-digital converter that delivers high dynamic performance at low power. It is part of the pin-compatible ISLA212P family built on Intersil's proprietary FemtoCharge™ technology on a standard CMOS process, allowing sampling rates up to 250 MSPS, 200 MSPS, and 130 MSPS variants from a single 72-contact QFN (10 mm x 10 mm) footprint with an exposed thermal paddle. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a sampling converter that uses a binary-search algorithm against a precision DAC to resolve the input voltage one bit per clock cycle. SAR ADCs sit in the data-converter hierarchy as ADC -> Nyquist/oversampling ADC -> mixed-signal IC -> semiconductor. They offer excellent linearity, deterministic latency, and low power compared to flash or pipeline converters at moderate sample rates, making them well-suited to instrumentation, communications baseband, and wideband test equipment. Key headline specifications of the ISLA212P20IRZ include 12-bit resolution, 200 MSPS sampling rate, LVDS/CMOS-selectable digital outputs, SPI configuration port, and -40 °C to +85 °C industrial operating range. The device supports both single-data-rate (full-width SDR) and double-data-rate (half-width DDR) output modes, giving system designers flexibility for FPGA, ASIC, or DSP capture. A 72-contact QFN package with an exposed paddle supplies a low thermal-resistance path for high-clock full-rate operation. Architecturally, the part uses FemtoCharge™ switched-capacitor input sampling and an internal high-precision reference, with optional external reference support. Its pipeline-style latency is deterministic and pipelined-friendly, simplifying FPGA capture at multi-hundred-megasample rates. Gain, offset, and output timing are adjustable through the SPI port, supporting per-channel calibration in multi-board systems. Typical applications for the ISLA212P20IRZ include wideband test and measurement instruments, radar IF/baseband digitizers, communications receiver baseband I/Q capture, medical imaging front-ends, and high-channel-count data-acquisition systems. The combination of 12-bit resolution, 200 MSPS throughput, and low power suits portable and ruggedized platforms where thermal density must be controlled. Designers should provide adequate ground and decoupling on the analog and digital rails, follow the exposed-paddle soldering recommendations (see manufacturer application layout), and verify SPI configuration timing during bring-up. When migrating between family members, no PCB rework is required. This page synthesizes distributor pricing, validated drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet header alone.

Запрос цены Контакты
ISLA214P12IRZ - 14-Bit 125MSPS SAR ADC | Renesas Electronics
ISLA214P12IRZ

ISLA214P12IRZ - 14-Bit 125MSPS SAR ADC | Renesas Electronics

The Renesas Electronics (formerly Intersil) ISLA214P12IRZ is a 14-bit, 125 MSPS successive-approximation-register (SAR) analog-to-digital converter delivering very high dynamic range and low power consumption, packaged in a 72-pin QFN (10x10 mm). The part offers 1 differential input channel with unbuffered (switched-capacitor) analog inputs and is part of a pin-compatible family of 12- to 16-bit ADCs with sample rates from 125 MSPS to 500 MSPS, allowing a single PCB layout to migrate across resolution and speed grades. A SAR ADC is a type of analog-to-digital converter that uses a binary-search algorithm implemented with a capacitive DAC and a high-speed comparator to resolve each conversion in N clock cycles for N-bit resolution. SAR ADCs are valued for their deterministic latency, single-shot accuracy, and excellent dynamic performance, and they sit at the leaf of the broader data-converter hierarchy: SAR ADC -> A/D converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor. The ISLA214P12 uses a high-performance, low-power core that is well suited for instrumentation, communications and imaging front ends where both speed and DC accuracy matter. Key differentiating features include 125 MSPS maximum sampling rate, 14-bit resolution, 1.8 V/3.3 V supply operation, LVDS/LVCMOS-compatible digital outputs, and an internal reference. The 72-QFN (10x10) package provides a low thermal-resistance path and is footprint-compatible with the wider ISLA214P/ISLA216P/ISLA214S/ISLA216S family, so a single PCB layout can be reused across multiple performance tiers. The device also integrates an input common-mode clamp and a self-calibrating background circuit that maintains DC accuracy over temperature. The pin-compatible family approach means a system designed around the ISLA214P12IRZ can be re-populated with ISLA214P25, ISLA214P50 or higher-resolution members (ISLA216P25/ISLA216P50) when additional sample rate or resolution is required, with no PCB changes. This is particularly valuable for multi-product platforms where one design must address multiple market tiers. Typical applications include communications test equipment, radar and signal-intelligence front ends, medical imaging (ultrasound beamformers), high-speed data acquisition cards, and industrial imaging. Designers favor the ISLA214P12IRZ when very high dynamic range, low latency and pin-compatible scalability across the ISLA214P/ISLA216P family are required within a 72-QFN footprint. When designing with this converter, pay close attention to the analog-input network: a wide-band, low-distortion differential driver (such as the ISL552xx or ADA4937 family) must present the proper common-mode voltage and source impedance to the unbuffered switched-capacitor inputs. Decouple each supply pin individually with 100 nF ceramic capacitors placed as close as possible to the package, and provide a solid ground plane under the exposed pad to minimize digital switching noise coupling into the analog front end. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes (clock, input network, decoupling, exposed-pad soldering) not found in a single place in the manufacturer datasheet, giving engineers a faster starting point for ISLA214P12IRZ-based designs.

Запрос цены Контакты