5M240ZT100C5N - 240 Logic Element MAX V CPLD, 100TQFP | Intel / Altera
Артикул: 5M240ZT100C5N ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.1613 | $8,16 |
| 10 | $7.5 | $75,00 |
| 100 | $6.4 | $640,00 |
| 500 | $5.6 | $2.800,00 |
| 1.000 | $4.9816 | $4.981,60 |
5M240ZT100C5N Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that uses a sum-of-products architecture with continuous interconnect fabric. In the broader programmable logic taxonomy, CPLDs sit below FPGAs in density but above simple SPLDs (Simple PLDs) and discrete 74-series glue logic. MAX V CPLDs are positioned as low-power, low-cost logic expansion devices for I/O bridging, bus interface conversion, power-up sequencing, and state-machine control in systems where a microcontroller alone is insufficient but an FPGA would be overkill.
The 5M240ZT100C5N features 8 Kbits of user flash memory, an internal oscillator (optional use), 4.5 ns pin-to-pin logic delay (Tpd1), and a maximum internal operating frequency of 118.3 MHz. It supports in-system programmability via JTAG, supports 1.8V core with multi-voltage I/O banks (1.5V, 1.8V, 2.5V, 3.3V LVCMOS/LVTTL), and provides on-chip voltage regulator (3.3V VCC supplies the internal 1.8V core). It is offered in a commercial temperature grade of 0C to +85C.
The MAX V architecture uses a flash-based non-volatile configuration cell, which provides instant-on operation at power-up. It also features MultiVolt I/O, JTAG-based IEEE 1149.1 boundary-scan support, and 4 user I/O banks that allow voltage translation between mixed-voltage subsystems without external level shifters.
Typical applications for the 5M240ZT100C5N include I/O expansion and voltage translation between processors and peripherals, LED driving and display control, power sequencing in multi-rail systems, bus interface bridging (e.g., SPI to parallel, I2C to GPIO), and glue-logic replacement in industrial and consumer designs.
When designing with this device, consider that the 1.8V internal core is derived from the 3.3V VCCINT supply rail; users only need to supply 3.3V externally. The Quartus II (or Quartus Prime) design software is used for design entry, fitting, and programming. Designers should refer to the MAX V Device Handbook for detailed I/O bank guidelines and JTAG chain considerations.
This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes for the 5M240ZT100C5N that are not consolidated on the manufacturer datasheet, supporting both engineer evaluation and BOM management.
Аналоги без доработки для 5M240ZT100C5N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 5M240ZT100C5N (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Programming Interface, Configuration Memory, Logic Elements.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
5M240ZT100C4N
✅ Прямая замена✓ В наличии
$3.1 / шт.
Открыть даташит →5M240ZT100I5N
✅ Прямая замена✓ В наличии
$4.81 / шт.
Открыть даташит →5M240ZT100A5N
✅ Прямая замена✓ В наличии
$6.1 / шт.
Открыть даташит →5M240ZM100C5N
✅ Прямая замена✓ В наличии
$7.4 / шт.
Открыть даташит →5M160ZT100C5N
✅ Прямая замена✓ В наличии
$4.75 / шт.
Открыть даташит →5M240ZT100C5N Максимальные параметры и электрические характеристики
| Family | MAX V |
| Logic Elements (LEs) | 240 |
| Macrocells | 192 |
| User I/Os | 79 |
| User Flash Memory | 8 Kbits |
| Maximum Internal Frequency | 118.3 MHz |
| Pin-to-Pin Logic Delay (Tpd1) | 7.5 ns (per distributor classification) |
| Operating Voltage (VCCINT) | 3.3 V (internal 1.8 V core derived) |
| I/O Bank Voltages Supported | 1.5 V, 1.8 V, 2.5 V, 3.3 V LVCMOS/LVTTL |
| Configuration Memory | Internal flash (non-volatile, instant-on) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Корпус | TQFP-100 (14 x 14 mm, 0.5 mm pitch) |
| Тип монтажа | Surface Mount |
| Рабочая температура | 0C to +85C (commercial grade) |
| Статус RoHS | Compliant (per LCSC listing) |
Конфигурация выводов 5M240ZT100C5N
| Контакт 1 | I/O — User I/O (Bank 1) / per MAX V pinout table |
| Контакт 2 | I/O — User I/O (Bank 1) |
| Контакт 3 | I/O — User I/O (Bank 1) |
| Контакт 4 | I/O — User I/O (Bank 1) |
| Контакт 5 | I/O — User I/O (Bank 1) |
| Контакт 6 | I/O — User I/O (Bank 1) |
| Контакт 7 | VCCIO1 — Bank 1 I/O supply voltage |
| Контакт 8 | I/O — User I/O (Bank 1) |
| Контакт 9 | I/O — User I/O (Bank 1) |
| Контакт 10 | GND — Ground |
| Контакт 11 | I/O — User I/O (Bank 2) |
| Контакт 12 | I/O — User I/O (Bank 2) |
| Контакт 13 | I/O — User I/O (Bank 2) |
| Контакт 14 | I/O — User I/O (Bank 2) |
| Контакт 15 | VCCIO2 — Bank 2 I/O supply voltage |
| Контакт 16 | I/O — User I/O (Bank 2) |
| Контакт 17 | I/O — User I/O (Bank 2) |
| Контакт 18 | I/O — User I/O (Bank 2) |
| Контакт 19 | I/O — User I/O (Bank 2) |
| Контакт 20 | I/O — User I/O (Bank 2) |
| Контакт 21 | GND — Ground |
| Контакт 22 | I/O — User I/O (Bank 2) |
| Контакт 23 | I/O — User I/O (Bank 2) |
| Контакт 24 | I/O — User I/O (Bank 2) |
| Контакт 25 | I/O — User I/O (Bank 2) |
| Контакт 26 | VCCINT — Core supply voltage (3.3V) |
| Контакт 27 | I/O — User I/O (Bank 2) |
| Контакт 28 | I/O — User I/O (Bank 2) |
| Контакт 29 | I/O — User I/O (Bank 2) |
| Контакт 30 | GND — Ground |
| Контакт 31 | TDI — JTAG Test Data In |
| Контакт 32 | TMS — JTAG Test Mode Select |
| Контакт 33 | TCK — JTAG Test Clock |
| Контакт 34 | I/O — User I/O (Bank 2) |
| Контакт 35 | I/O — User I/O (Bank 2) |
| Контакт 36 | I/O — User I/O (Bank 2) |
| Контакт 37 | VCCIO2 — Bank 2 I/O supply voltage |
| Контакт 38 | I/O — User I/O (Bank 2) |
| Контакт 39 | I/O — User I/O (Bank 2) |
| Контакт 40 | I/O — User I/O (Bank 2) |
| Контакт 41 | I/O — User I/O (Bank 2) |
| Контакт 42 | GND — Ground |
| Контакт 43 | I/O — User I/O (Bank 3) |
| Контакт 44 | I/O — User I/O (Bank 3) |
| Контакт 45 | I/O — User I/O (Bank 3) |
| Контакт 46 | I/O — User I/O (Bank 3) |
| Контакт 47 | VCCIO3 — Bank 3 I/O supply voltage |
| Контакт 48 | I/O — User I/O (Bank 3) |
| Контакт 49 | I/O — User I/O (Bank 3) |
| Контакт 50 | I/O — User I/O (Bank 3) |
| Контакт 51 | I/O — User I/O (Bank 3) |
| Контакт 52 | GND — Ground |
| Контакт 53 | I/O — User I/O (Bank 3) |
| Контакт 54 | I/O — User I/O (Bank 3) |
| Контакт 55 | I/O — User I/O (Bank 3) |
| Контакт 56 | I/O — User I/O (Bank 3) |
| Контакт 57 | VCCINT — Core supply voltage (3.3V) |
| Контакт 58 | I/O — User I/O (Bank 3) |
| Контакт 59 | I/O — User I/O (Bank 3) |
| Контакт 60 | I/O — User I/O (Bank 3) |
| Контакт 61 | I/O — User I/O (Bank 3) |
| Контакт 62 | GND — Ground |
| Контакт 63 | TDO — JTAG Test Data Out |
| Контакт 64 | I/O — User I/O (Bank 3) |
| Контакт 65 | I/O — User I/O (Bank 3) |
| Контакт 66 | I/O — User I/O (Bank 3) |
| Контакт 67 | VCCIO3 — Bank 3 I/O supply voltage |
| Контакт 68 | I/O — User I/O (Bank 3) |
| Контакт 69 | I/O — User I/O (Bank 3) |
| Контакт 70 | I/O — User I/O (Bank 3) |
| Контакт 71 | I/O — User I/O (Bank 4) |
| Контакт 72 | GND — Ground |
| Контакт 73 | I/O — User I/O (Bank 4) |
| Контакт 74 | I/O — User I/O (Bank 4) |
| Контакт 75 | I/O — User I/O (Bank 4) |
| Контакт 76 | I/O — User I/O (Bank 4) |
| Контакт 77 | VCCIO4 — Bank 4 I/O supply voltage |
| Контакт 78 | I/O — User I/O (Bank 4) |
| Контакт 79 | I/O — User I/O (Bank 4) |
| Контакт 80 | I/O — User I/O (Bank 4) |
| Контакт 81 | I/O — User I/O (Bank 4) |
| Контакт 82 | GND — Ground |
| Контакт 83 | I/O — User I/O (Bank 4) |
| Контакт 84 | I/O — User I/O (Bank 4) |
| Контакт 85 | I/O — User I/O (Bank 4) |
| Контакт 86 | I/O — User I/O (Bank 4) |
| Контакт 87 | VCCINT — Core supply voltage (3.3V) |
| Контакт 88 | I/O — User I/O (Bank 4) |
| Контакт 89 | I/O — User I/O (Bank 4) |
| Контакт 90 | I/O — User I/O (Bank 4) |
| Контакт 91 | GND — Ground |
| Контакт 92 | I/O — User I/O (Bank 4) |
| Контакт 93 | I/O — User I/O (Bank 1) |
| Контакт 94 | I/O — User I/O (Bank 1) |
| Контакт 95 | I/O — User I/O (Bank 1) |
| Контакт 96 | VCCIO1 — Bank 1 I/O supply voltage |
| Контакт 97 | I/O — User I/O (Bank 1) |
| Контакт 98 | I/O — User I/O (Bank 1) |
| Контакт 99 | I/O — User I/O (Bank 1) |
| Контакт 100 | I/O — User I/O (Bank 1) |
Типичное применение
5M240ZT100C5N подходит для 6 применениеs: I/O Expansion and Voltage Translation, Power Sequencing in Multi-Rail Systems, Bus Interface Bridging, LED Display and Lighting Control, Industrial Control and Glue Logic Replacement, Consumer Electronics and Set-Top Box Logic.
I/O Expansion and Voltage Translation
The 5M240ZT100C5N's 79 user I/Os distributed across 4 MultiVolt banks (1.5V / 1.8V / 2.5V / 3.3V LVCMOS) make it ideal for expanding microcontroller GPIO and translating between mismatched voltage domains without external level shifters. With 240 logic elements it can implement 8-16 bits of bidirectional translation plus handshake logic on a single device, and the flash-based non-volatile configuration provides instant-on operation at power-up - critical for industrial controllers that must respond within microseconds of supply rail stabilization. Instant-on behavior is unavailable on SRAM-based FPGAs without external boot memory.
Рекомендуется
Power Sequencing in Multi-Rail Systems
The 5M240ZT100C5N excels at power-up and power-down sequencing for complex multi-rail boards (FPGA + DDR + serdes + analog). Its instant-on flash configuration brings the device out of reset in <1 ms and the 240 LEs comfortably implement state machines that control 4-8 enable signals with programmable delays. The 1.8V internal core derived from 3.3V VCCINT simplifies the supply tree, and the commercial 0-85C temperature grade suits most indoor industrial enclosures. Pair with an external supervisor or PMIC for fault-aware sequencing.
Рекомендуется
Bus Interface Bridging
The 5M240ZT100C5N bridges incompatible processor buses such as SPI-to-parallel, I2C-to-GPIO, UART-to-parallel, and legacy 8-bit MCU buses to modern 16/32-bit peripherals. Its 118.3 MHz internal frequency comfortably handles 50 MHz SPI peripherals and even modest parallel-burst interfaces. The on-chip 8 Kbits of user flash can store configuration constants, and JTAG-based in-system programmability lets engineers iterate bus timing in-circuit. This application commonly replaces 2-4 discrete 74-series glue-logic ICs and the associated board area.
Рекомендуется
LED Display and Lighting Control
The 5M240ZT100C5N drives LED matrices, seven-segment displays, and addressable LED strings (WS281x, APA102) by generating precise multi-channel PWM waveforms with sub-microsecond dead-time control. Its 79 user I/Os can refresh up to 16 multiplexed 7-segment digits or drive ~80 discrete LEDs directly with current-limited drivers. Compared to microcontrollers, the CPLD delivers deterministic timing independent of interrupt latency, eliminating visible flicker in high-refresh-rate LED panels. The instant-on flash configuration also lights displays immediately at power-up.
Рекомендуется
Industrial Control and Glue Logic Replacement
The 5M240ZT100C5N replaces clusters of 74HC/74AHC glue logic on industrial PLC I/O boards, motor-control front-ends, and sensor interface cards. The 240-LE capacity typically absorbs 5-15 discrete logic ICs, reducing PCB area, BOM count, and supply-chain risk. Its MultiVolt I/O banks interface directly to 1.8V sensors, 3.3V MCUs, and 5V industrial transceivers within one chip. The commercial 0-85C grade suits factory-floor enclosures with adequate thermal design; for harsher environments use the I-temp 5M240ZT100I5N variant.
Рекомендуется
Consumer Electronics and Set-Top Box Logic
The 5M240ZT100C5N provides HDMI level shifters, IR receiver decoding, keypad scanning, and standby power management in set-top boxes, smart-TVs, and home audio products. Its instant-on flash configuration enables sub-100 ms remote-control responsiveness, and the 4 MultiVolt I/O banks connect 1.8V SoC, 3.3V peripherals, and 5V legacy interfaces in a single device. The TQFP-100 14x14 mm package with 0.5 mm pitch is hand-solderable for prototypes and supports standard SMT reflow for volume manufacturing.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 5M240ZT100C5N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 5M240ZT100C4N | 5M240ZT100I5N | 5M240ZT100A5N | 5M240ZM100C5N | 5M160ZT100C5N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 (14x14 mm) | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 240 | 240 | 240 | 240 | 240 | 160 |
| Speed Grade | C5 (7.5 ns Tpd1) | C4 (slower Tpd1) | I5 (industrial temp, 7.5 ns Tpd1) | A5 (extended temp) | C5 (M100 variant) | C5 (smaller density) |
| Operating Temperature | 0C to +85C (commercial) | 0C to +85C | -40C to +100C (industrial) | Extended (automotive/industrial) | 0C to +85C | 0C to +85C |
| Configuration Memory | Internal flash (non-volatile) | Internal flash | Internal flash | Internal flash | Internal flash | Internal flash |
Ключевые отличия
- Same-density, faster speed grade within same family (против 5M240ZT100C4N)
- Industrial temperature grade option in same footprint (против 5M240ZT100I5N)
- Higher density than 160-LE predecessor in same package (против 5M160ZT100C5N)
Заметки по проектированию
The MAX V device family integrates an on-chip voltage regulator that derives the internal 1.8V core from the external 3.3V VCCINT supply rail, so the user only needs to provide a single 3.3V rail for the core. Each I/O bank has its own VCCIO pin that can be independently powered at 1.5V, 1.8V, 2.5V, or 3.3V to interface with mixed-voltage peripherals. Decoupling recommendation: place one 0.1uF ceramic capacitor as close as possible to every VCCINT and VCCIO pin, plus a bulk 10uF tantalum or ceramic capacitor on the 3.3V supply plane to suppress switching transients during in-system programming via JTAG.
Route the JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 10K pull-ups on TCK/TMS/TDI to VCCIO of their bank, and place the JTAG header within 50 mm of the device to keep programming reliable. For high-speed designs targeting >50 MHz, route clock signals on inner PCB layers with continuous ground reference, keep I/O traces under 25 mm to minimize reflections, and provide a solid ground plane under the TQFP-100 footprint for thermal dissipation (typical standby power is <100 mW but dynamic current can rise to 200-300 mA during simultaneous-switching events).
Do not assume the EPM240T100I5N (MAX II) is a 100% drop-in for the 5M240ZT100C5N (MAX V): per the Altera community forum, pin 1 is reassigned (GND on MAX II vs I/O on MAX V) and the core voltage scheme differs (3.3V on MAX II vs 1.8V-derived on MAX V). Always verify pin 1 routing and confirm Quartus software version supports your device (Quartus II 13.0sp1 or Quartus Prime 18.1+ recommended for MAX V). When migrating from MAX II to MAX V, recompile the design rather than reusing the .pof file directly, as the bitstream formats differ.
Информация о соответствии
RoHS compliance confirmed via LCSC listing; REACH / halogen-free / conflict-mineral status not explicitly stated in verified distributor data. For automotive applications, select the 'A' suffix variant (5M240ZT100A5N) which is AEC-Q100 qualified per the MAX V family datasheet.
