5M240ZT100C5N - 240 Logic Element MAX V CPLD, 100TQFP | Intel / Altera
N.º da peça: 5M240ZT100C5N ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $8.1613 | $8,16 |
| 10 | $7.5 | $75,00 |
| 100 | $6.4 | $640,00 |
| 500 | $5.6 | $2.800,00 |
| 1.000 | $4.9816 | $4.981,60 |
5M240ZT100C5N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that uses a sum-of-products architecture with continuous interconnect fabric. In the broader programmable logic taxonomy, CPLDs sit below FPGAs in density but above simple SPLDs (Simple PLDs) and discrete 74-series glue logic. MAX V CPLDs are positioned as low-power, low-cost logic expansion devices for I/O bridging, bus interface conversion, power-up sequencing, and state-machine control in systems where a microcontroller alone is insufficient but an FPGA would be overkill.
The 5M240ZT100C5N features 8 Kbits of user flash memory, an internal oscillator (optional use), 4.5 ns pin-to-pin logic delay (Tpd1), and a maximum internal operating frequency of 118.3 MHz. It supports in-system programmability via JTAG, supports 1.8V core with multi-voltage I/O banks (1.5V, 1.8V, 2.5V, 3.3V LVCMOS/LVTTL), and provides on-chip voltage regulator (3.3V VCC supplies the internal 1.8V core). It is offered in a commercial temperature grade of 0C to +85C.
The MAX V architecture uses a flash-based non-volatile configuration cell, which provides instant-on operation at power-up. It also features MultiVolt I/O, JTAG-based IEEE 1149.1 boundary-scan support, and 4 user I/O banks that allow voltage translation between mixed-voltage subsystems without external level shifters.
Typical applications for the 5M240ZT100C5N include I/O expansion and voltage translation between processors and peripherals, LED driving and display control, power sequencing in multi-rail systems, bus interface bridging (e.g., SPI to parallel, I2C to GPIO), and glue-logic replacement in industrial and consumer designs.
When designing with this device, consider that the 1.8V internal core is derived from the 3.3V VCCINT supply rail; users only need to supply 3.3V externally. The Quartus II (or Quartus Prime) design software is used for design entry, fitting, and programming. Designers should refer to the MAX V Device Handbook for detailed I/O bank guidelines and JTAG chain considerations.
This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes for the 5M240ZT100C5N that are not consolidated on the manufacturer datasheet, supporting both engineer evaluation and BOM management.
Alternativas drop-in para 5M240ZT100C5N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M240ZT100C5N (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Programming Interface, Configuration Memory, Logic Elements.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M240ZT100C4N
✅ Drop-In✓ Em estoque
$3.1 / unidade
Ver ficha técnica →5M240ZT100I5N
✅ Drop-In✓ Em estoque
$4.81 / unidade
Ver ficha técnica →5M240ZT100A5N
✅ Drop-In✓ Em estoque
$6.1 / unidade
Ver ficha técnica →5M240ZM100C5N
✅ Drop-In✓ Em estoque
$7.4 / unidade
Ver ficha técnica →5M160ZT100C5N
✅ Drop-In✓ Em estoque
$4.75 / unidade
Ver ficha técnica →5M240ZT100C5N Classificações máximas e características elétricas
| Family | MAX V |
| Logic Elements (LEs) | 240 |
| Macrocells | 192 |
| User I/Os | 79 |
| User Flash Memory | 8 Kbits |
| Maximum Internal Frequency | 118.3 MHz |
| Pin-to-Pin Logic Delay (Tpd1) | 7.5 ns (per distributor classification) |
| Operating Voltage (VCCINT) | 3.3 V (internal 1.8 V core derived) |
| I/O Bank Voltages Supported | 1.5 V, 1.8 V, 2.5 V, 3.3 V LVCMOS/LVTTL |
| Configuration Memory | Internal flash (non-volatile, instant-on) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Encapsulamento | TQFP-100 (14 x 14 mm, 0.5 mm pitch) |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | 0C to +85C (commercial grade) |
| Status RoHS | Compliant (per LCSC listing) |
Configuração de pinos do 5M240ZT100C5N
| Pino 1 | I/O — User I/O (Bank 1) / per MAX V pinout table |
| Pino 2 | I/O — User I/O (Bank 1) |
| Pino 3 | I/O — User I/O (Bank 1) |
| Pino 4 | I/O — User I/O (Bank 1) |
| Pino 5 | I/O — User I/O (Bank 1) |
| Pino 6 | I/O — User I/O (Bank 1) |
| Pino 7 | VCCIO1 — Bank 1 I/O supply voltage |
| Pino 8 | I/O — User I/O (Bank 1) |
| Pino 9 | I/O — User I/O (Bank 1) |
| Pino 10 | GND — Ground |
| Pino 11 | I/O — User I/O (Bank 2) |
| Pino 12 | I/O — User I/O (Bank 2) |
| Pino 13 | I/O — User I/O (Bank 2) |
| Pino 14 | I/O — User I/O (Bank 2) |
| Pino 15 | VCCIO2 — Bank 2 I/O supply voltage |
| Pino 16 | I/O — User I/O (Bank 2) |
| Pino 17 | I/O — User I/O (Bank 2) |
| Pino 18 | I/O — User I/O (Bank 2) |
| Pino 19 | I/O — User I/O (Bank 2) |
| Pino 20 | I/O — User I/O (Bank 2) |
| Pino 21 | GND — Ground |
| Pino 22 | I/O — User I/O (Bank 2) |
| Pino 23 | I/O — User I/O (Bank 2) |
| Pino 24 | I/O — User I/O (Bank 2) |
| Pino 25 | I/O — User I/O (Bank 2) |
| Pino 26 | VCCINT — Core supply voltage (3.3V) |
| Pino 27 | I/O — User I/O (Bank 2) |
| Pino 28 | I/O — User I/O (Bank 2) |
| Pino 29 | I/O — User I/O (Bank 2) |
| Pino 30 | GND — Ground |
| Pino 31 | TDI — JTAG Test Data In |
| Pino 32 | TMS — JTAG Test Mode Select |
| Pino 33 | TCK — JTAG Test Clock |
| Pino 34 | I/O — User I/O (Bank 2) |
| Pino 35 | I/O — User I/O (Bank 2) |
| Pino 36 | I/O — User I/O (Bank 2) |
| Pino 37 | VCCIO2 — Bank 2 I/O supply voltage |
| Pino 38 | I/O — User I/O (Bank 2) |
| Pino 39 | I/O — User I/O (Bank 2) |
| Pino 40 | I/O — User I/O (Bank 2) |
| Pino 41 | I/O — User I/O (Bank 2) |
| Pino 42 | GND — Ground |
| Pino 43 | I/O — User I/O (Bank 3) |
| Pino 44 | I/O — User I/O (Bank 3) |
| Pino 45 | I/O — User I/O (Bank 3) |
| Pino 46 | I/O — User I/O (Bank 3) |
| Pino 47 | VCCIO3 — Bank 3 I/O supply voltage |
| Pino 48 | I/O — User I/O (Bank 3) |
| Pino 49 | I/O — User I/O (Bank 3) |
| Pino 50 | I/O — User I/O (Bank 3) |
| Pino 51 | I/O — User I/O (Bank 3) |
| Pino 52 | GND — Ground |
| Pino 53 | I/O — User I/O (Bank 3) |
| Pino 54 | I/O — User I/O (Bank 3) |
| Pino 55 | I/O — User I/O (Bank 3) |
| Pino 56 | I/O — User I/O (Bank 3) |
| Pino 57 | VCCINT — Core supply voltage (3.3V) |
| Pino 58 | I/O — User I/O (Bank 3) |
| Pino 59 | I/O — User I/O (Bank 3) |
| Pino 60 | I/O — User I/O (Bank 3) |
| Pino 61 | I/O — User I/O (Bank 3) |
| Pino 62 | GND — Ground |
| Pino 63 | TDO — JTAG Test Data Out |
| Pino 64 | I/O — User I/O (Bank 3) |
| Pino 65 | I/O — User I/O (Bank 3) |
| Pino 66 | I/O — User I/O (Bank 3) |
| Pino 67 | VCCIO3 — Bank 3 I/O supply voltage |
| Pino 68 | I/O — User I/O (Bank 3) |
| Pino 69 | I/O — User I/O (Bank 3) |
| Pino 70 | I/O — User I/O (Bank 3) |
| Pino 71 | I/O — User I/O (Bank 4) |
| Pino 72 | GND — Ground |
| Pino 73 | I/O — User I/O (Bank 4) |
| Pino 74 | I/O — User I/O (Bank 4) |
| Pino 75 | I/O — User I/O (Bank 4) |
| Pino 76 | I/O — User I/O (Bank 4) |
| Pino 77 | VCCIO4 — Bank 4 I/O supply voltage |
| Pino 78 | I/O — User I/O (Bank 4) |
| Pino 79 | I/O — User I/O (Bank 4) |
| Pino 80 | I/O — User I/O (Bank 4) |
| Pino 81 | I/O — User I/O (Bank 4) |
| Pino 82 | GND — Ground |
| Pino 83 | I/O — User I/O (Bank 4) |
| Pino 84 | I/O — User I/O (Bank 4) |
| Pino 85 | I/O — User I/O (Bank 4) |
| Pino 86 | I/O — User I/O (Bank 4) |
| Pino 87 | VCCINT — Core supply voltage (3.3V) |
| Pino 88 | I/O — User I/O (Bank 4) |
| Pino 89 | I/O — User I/O (Bank 4) |
| Pino 90 | I/O — User I/O (Bank 4) |
| Pino 91 | GND — Ground |
| Pino 92 | I/O — User I/O (Bank 4) |
| Pino 93 | I/O — User I/O (Bank 1) |
| Pino 94 | I/O — User I/O (Bank 1) |
| Pino 95 | I/O — User I/O (Bank 1) |
| Pino 96 | VCCIO1 — Bank 1 I/O supply voltage |
| Pino 97 | I/O — User I/O (Bank 1) |
| Pino 98 | I/O — User I/O (Bank 1) |
| Pino 99 | I/O — User I/O (Bank 1) |
| Pino 100 | I/O — User I/O (Bank 1) |
Aplicações típicas
5M240ZT100C5N é adequado para 6 aplicaçãos: I/O Expansion and Voltage Translation, Power Sequencing in Multi-Rail Systems, Bus Interface Bridging, LED Display and Lighting Control, Industrial Control and Glue Logic Replacement, Consumer Electronics and Set-Top Box Logic.
I/O Expansion and Voltage Translation
The 5M240ZT100C5N's 79 user I/Os distributed across 4 MultiVolt banks (1.5V / 1.8V / 2.5V / 3.3V LVCMOS) make it ideal for expanding microcontroller GPIO and translating between mismatched voltage domains without external level shifters. With 240 logic elements it can implement 8-16 bits of bidirectional translation plus handshake logic on a single device, and the flash-based non-volatile configuration provides instant-on operation at power-up - critical for industrial controllers that must respond within microseconds of supply rail stabilization. Instant-on behavior is unavailable on SRAM-based FPGAs without external boot memory.
Recomendado
Power Sequencing in Multi-Rail Systems
The 5M240ZT100C5N excels at power-up and power-down sequencing for complex multi-rail boards (FPGA + DDR + serdes + analog). Its instant-on flash configuration brings the device out of reset in <1 ms and the 240 LEs comfortably implement state machines that control 4-8 enable signals with programmable delays. The 1.8V internal core derived from 3.3V VCCINT simplifies the supply tree, and the commercial 0-85C temperature grade suits most indoor industrial enclosures. Pair with an external supervisor or PMIC for fault-aware sequencing.
Recomendado
Bus Interface Bridging
The 5M240ZT100C5N bridges incompatible processor buses such as SPI-to-parallel, I2C-to-GPIO, UART-to-parallel, and legacy 8-bit MCU buses to modern 16/32-bit peripherals. Its 118.3 MHz internal frequency comfortably handles 50 MHz SPI peripherals and even modest parallel-burst interfaces. The on-chip 8 Kbits of user flash can store configuration constants, and JTAG-based in-system programmability lets engineers iterate bus timing in-circuit. This application commonly replaces 2-4 discrete 74-series glue-logic ICs and the associated board area.
Recomendado
LED Display and Lighting Control
The 5M240ZT100C5N drives LED matrices, seven-segment displays, and addressable LED strings (WS281x, APA102) by generating precise multi-channel PWM waveforms with sub-microsecond dead-time control. Its 79 user I/Os can refresh up to 16 multiplexed 7-segment digits or drive ~80 discrete LEDs directly with current-limited drivers. Compared to microcontrollers, the CPLD delivers deterministic timing independent of interrupt latency, eliminating visible flicker in high-refresh-rate LED panels. The instant-on flash configuration also lights displays immediately at power-up.
Recomendado
Industrial Control and Glue Logic Replacement
The 5M240ZT100C5N replaces clusters of 74HC/74AHC glue logic on industrial PLC I/O boards, motor-control front-ends, and sensor interface cards. The 240-LE capacity typically absorbs 5-15 discrete logic ICs, reducing PCB area, BOM count, and supply-chain risk. Its MultiVolt I/O banks interface directly to 1.8V sensors, 3.3V MCUs, and 5V industrial transceivers within one chip. The commercial 0-85C grade suits factory-floor enclosures with adequate thermal design; for harsher environments use the I-temp 5M240ZT100I5N variant.
Recomendado
Consumer Electronics and Set-Top Box Logic
The 5M240ZT100C5N provides HDMI level shifters, IR receiver decoding, keypad scanning, and standby power management in set-top boxes, smart-TVs, and home audio products. Its instant-on flash configuration enables sub-100 ms remote-control responsiveness, and the 4 MultiVolt I/O banks connect 1.8V SoC, 3.3V peripherals, and 5V legacy interfaces in a single device. The TQFP-100 14x14 mm package with 0.5 mm pitch is hand-solderable for prototypes and supports standard SMT reflow for volume manufacturing.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M240ZT100C5N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M240ZT100C4N | 5M240ZT100I5N | 5M240ZT100A5N | 5M240ZM100C5N | 5M160ZT100C5N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 (14x14 mm) | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 240 | 240 | 240 | 240 | 240 | 160 |
| Speed Grade | C5 (7.5 ns Tpd1) | C4 (slower Tpd1) | I5 (industrial temp, 7.5 ns Tpd1) | A5 (extended temp) | C5 (M100 variant) | C5 (smaller density) |
| Operating Temperature | 0C to +85C (commercial) | 0C to +85C | -40C to +100C (industrial) | Extended (automotive/industrial) | 0C to +85C | 0C to +85C |
| Configuration Memory | Internal flash (non-volatile) | Internal flash | Internal flash | Internal flash | Internal flash | Internal flash |
Principais diferenciais
- Same-density, faster speed grade within same family (vs 5M240ZT100C4N)
- Industrial temperature grade option in same footprint (vs 5M240ZT100I5N)
- Higher density than 160-LE predecessor in same package (vs 5M160ZT100C5N)
Notas de projeto
The MAX V device family integrates an on-chip voltage regulator that derives the internal 1.8V core from the external 3.3V VCCINT supply rail, so the user only needs to provide a single 3.3V rail for the core. Each I/O bank has its own VCCIO pin that can be independently powered at 1.5V, 1.8V, 2.5V, or 3.3V to interface with mixed-voltage peripherals. Decoupling recommendation: place one 0.1uF ceramic capacitor as close as possible to every VCCINT and VCCIO pin, plus a bulk 10uF tantalum or ceramic capacitor on the 3.3V supply plane to suppress switching transients during in-system programming via JTAG.
Route the JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 10K pull-ups on TCK/TMS/TDI to VCCIO of their bank, and place the JTAG header within 50 mm of the device to keep programming reliable. For high-speed designs targeting >50 MHz, route clock signals on inner PCB layers with continuous ground reference, keep I/O traces under 25 mm to minimize reflections, and provide a solid ground plane under the TQFP-100 footprint for thermal dissipation (typical standby power is <100 mW but dynamic current can rise to 200-300 mA during simultaneous-switching events).
Do not assume the EPM240T100I5N (MAX II) is a 100% drop-in for the 5M240ZT100C5N (MAX V): per the Altera community forum, pin 1 is reassigned (GND on MAX II vs I/O on MAX V) and the core voltage scheme differs (3.3V on MAX II vs 1.8V-derived on MAX V). Always verify pin 1 routing and confirm Quartus software version supports your device (Quartus II 13.0sp1 or Quartus Prime 18.1+ recommended for MAX V). When migrating from MAX II to MAX V, recompile the design rather than reusing the .pof file directly, as the bitstream formats differ.
Informações de conformidade
RoHS compliance confirmed via LCSC listing; REACH / halogen-free / conflict-mineral status not explicitly stated in verified distributor data. For automotive applications, select the 'A' suffix variant (5M240ZT100A5N) which is AEC-Q100 qualified per the MAX V family datasheet.
