A3P125-VQ100 - 125K-Gate 231MHz ProASIC3 FPGA | Microchip
Артикул: A3P125-VQ100 ✓ АктивенA3P125-VQ100 Обзор
A field-programmable gate array, or FPGA, is a semiconductor whose digital logic is configured after manufacture. A ProASIC3 FPGA belongs to the broader hierarchy of programmable logic devices, combining configurable logic, embedded RAM, programmable interconnect, and general-purpose I/O in one package. This makes the device suitable for consolidating separate glue logic, control logic, interface logic, and small embedded subsystems onto a single programmable board.
The A3P125-VQ100 provides 125,000 logic gates and 36,864 RAM bits in a compact 100-TQFP package. Its stated 231 MHz performance is useful for control systems, communications interfaces, instrumentation, embedded processors, and general-purpose logic consolidation where moderate clock performance and a small pin count are more important than the very high I/O counts available from larger FPGAs. The 14 x 14 mm package also supports dense surface-mount PCB layouts.
ProASIC3 devices use flash-based, nonvolatile configuration technology, allowing the programmed design to remain in the device without continuous configuration reload. This provides Instant On behavior and allows field upgrades without volatile RAM. The manufacturer describes the family as a reprogrammable, single-chip solution with a small footprint and low total cost of ownership, making it useful where production volumes are below the point where a custom ASIC is economical.
Typical applications include industrial automation and control, communications protocol handling, test and measurement equipment, embedded-system support logic, sensor conditioning, and general-purpose interface bridging. The 1.5 KLE device can also serve as a companion programmable controller when a system requires moderate logic density alongside a microcontroller or processor.
The principal design consideration is device utilization. Logic, RAM, dedicated pins, clock resources, and available I/O must be checked against the design before layout begins. Use the manufacturer pin-description table and package drawing to assign power, ground, configuration, clock, and user I/O connections, and verify the selected board-library footprint against the 100-TQFP mechanical drawing.
This product page combines the manufacturer family information with distributor technical summaries and practical comparison guidance. It organizes capacity, speed, package, temperature, replacement, and sourcing information so engineers can assess whether the A3P125-VQ100 fits a specific programmable-logic design before starting a board layout.
Аналоги без доработки для A3P125-VQ100 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с A3P125-VQ100 (тот же форм-фактор и посадочное место) — отличается по Configuration Technology, Device Type, Logic Elements, Operating Temperature, Package.
A3P125-VQ100I
✅ Прямая заменаУточнить цену
Открыть даташит →A3P125-VQ100T
✅ Прямая заменаУточнить цену
Открыть даташит →A3P125-VQG100
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
A3P125-1VQ100
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
A3P125-VQ100C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
A3P125-VQ100 Максимальные параметры и электрические характеристики
| Device Type | ProASIC3 Field Programmable Gate Array (FPGA) |
| Logic Elements | 1.5K LEs |
| Number of Gates | 125,000 gates |
| Maximum Frequency | 231 MHz |
| Total RAM | 36,864 bits |
| Core Supply Voltage | 1.5 V |
| Process Technology | 130 nm CMOS |
| Configuration Technology | Flash-based nonvolatile configuration |
| Корпус | 100-TQFP, 14 x 14 mm |
| Способ монтажа | Surface Mount |
| Рабочая температура | 0 °C to 85 °C |
| Programmability | User-programmable flash configuration |
| Single-Chip Implementation | Supported |
| Logic and RAM Capacity | 125,000 gates and 36,864 RAM bits |
| Package Pin Count | 100 pins |
Руководство по цоколевке A3P125-VQ100 в корпусе 100 pins
Цоколевка для A3P125-VQ100 (корпус 100 pins). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для A3P125-VQ100.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
A3P125-VQ100 подходит для 6 применениеs: Industrial Automation and Control, Communications Protocol Interface, Test and Measurement Instrumentation, Embedded System Support Logic, Sensor Conditioning and Data Acquisition, LED Lighting Control.
Industrial Automation and Control
The A3P125-VQ100 is suitable for consolidating deterministic control logic, interlocks, state-machine sequencing, and peripheral interfacing in industrial equipment operating from 0 °C to 85 °C. Its 1.5K logic elements and 36,864 RAM bits provide enough configurable resources for small control subsystems, while the 231 MHz maximum frequency supports timing-sensitive logic. Flash-based configuration retains the programmed configuration without a continuous volatile reload. During implementation, place the device between the processor or sensor subsystem and its field-bus or I/O circuitry, then verify logic utilization, timing, and available 100-TQFP I/O before committing the PCB layout.
Рекомендуется
Communications Protocol Interface
The A3P125-VQ100 can implement protocol framing, filtering, packet checks, command parsing, and interface isolation where a compact programmable-logic block is preferable to a larger FPGA. Its 125,000 gates and 36,864 RAM bits accommodate parallel datapaths and small buffering requirements, while the 231 MHz maximum frequency supports clocked interface logic. The nonvolatile flash configuration also permits field upgrades without losing the stored design after power removal. Confirm signal timing against the selected speed grade and keep communication transceivers outside the FPGA when their analog or high-speed requirements exceed the A3P125-VQ100's I/O capabilities.
Рекомендуется
Test and Measurement Instrumentation
The A3P125-VQ100 is useful for instrument control, acquisition sequencing, trigger logic, calibration tables, and programmable signal-path management. The device provides 1.5K logic elements and 36,864 RAM bits for control and data-handling functions, with a stated 231 MHz maximum operating frequency for clocked logic. Because ProASIC3 configuration is nonvolatile, instrument subsystems can start from a stored design after power restoration. Designers should reserve enough I/O for the instrument's external interfaces, review timing margins for the selected package and grade, and compare accuracy-critical analog functions against dedicated converter or amplifier components.
Рекомендуется
Embedded System Support Logic
The A3P125-VQ100 can serve as a programmable companion to a microcontroller or processor by implementing glue logic, boot coordination, peripheral bridges, timers, and status aggregation. Its compact 14 x 14 mm 100-TQFP package helps preserve board area, and the nonvolatile flash configuration supports a deterministic startup path. The 36,864 RAM bits can hold modest packet, trace, or scheduling structures, while the 231 MHz maximum frequency allows the support logic to operate concurrently with the host processor. Validate bus timing, interrupt polarity, and I/O standards because these requirements determine whether the available device resources are sufficient.
Рекомендуется
Sensor Conditioning and Data Acquisition
The A3P125-VQ100 is appropriate for digital sensor aggregation, sampling control, filtering, timestamp generation, and interface conversion in compact acquisition modules. Its 125,000 gates can implement parallel datapaths and control sequences, while 36,864 RAM bits support small buffers or calibration tables. The 231 MHz maximum frequency provides margin for synchronous acquisition logic without requiring a larger device. Keep precision analog conversion and sensor excitation outside the FPGA unless their specifications explicitly permit integration, and verify acquisition timing against the actual clock configuration and selected A3P125 ordering grade.
Рекомендуется
LED Lighting Control
The A3P125-VQ100 can implement multi-channel LED sequencing, dimming state machines, fault logging, and communication-assisted lighting control. Its programmable logic supports adaptable timing and behavior without changing a fixed mask set, while nonvolatile flash configuration allows the controller to restart in the programmed state after a power interruption. The 1.5K logic elements and 36,864 RAM bits are appropriate for moderate channel counts and control tables. Confirm LED drive current, switching frequency, and thermal requirements in the external driver circuitry, and ensure the FPGA supplies only control signals rather than carrying the LED power directly.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для A3P125-VQ100 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | A3P125-VQ100I | A3P125-VQ100T | A3P125-VQG100 | A3P125-1VQ100 | A3P125-VQ100C |
|---|---|---|---|---|---|---|
| Package | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Device Type | ProASIC3 Field Programmable Gate Array | ProASIC3 Field Programmable Gate Array | ProASIC3 Field Programmable Gate Array | ProASIC3 Field Programmable Gate Array | ProASIC3 Field Programmable Gate Array | ProASIC3 Field Programmable Gate Array |
| Number of Gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates | 125,000 gates |
| Total RAM | 36,864 bits | 36,864 bits | 36,864 bits | 36,864 bits | 36,864 bits | 36,864 bits |
| Core Supply Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Process Technology | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS | 130 nm CMOS |
| Configuration Technology | Flash-based nonvolatile configuration | Flash-based nonvolatile configuration | Flash-based nonvolatile configuration | Flash-based nonvolatile configuration | Flash-based nonvolatile configuration | Flash-based nonvolatile configuration |
Ключевые отличия
- Compact nonvolatile programmable logic (против A3P125-VQ100I)
- Single-chip reprogrammable implementation (против A3P125-VQ100T)
- Moderate logic density with 231 MHz maximum frequency (против A3P125-VQG100)
- Field-reprogrammable design retention (против A3P125-1VQ100)
Заметки по проектированию
Assign power, ground, configuration, clock, and user I/O directly from the Microchip Technology ProASIC3 pin-description table. Cross-check every connection against the 100-TQFP 14 x 14 mm package drawing and your board library before routing. A pin assignment error in a dense programmable device can change the footprint's electrical role even when the physical lead location remains correct.
Use the core and I/O current tables in the family data sheet to size the 1.5 V supply under worst-case clocking and I/O activity. Place local bypass capacitors close to the package power pins and keep high-current return paths short. Estimated: total dissipation equals the sum of core power and I/O power, where core power is approximately 1.5 V multiplied by worst-case core current; validate the final result against the manufacturer's maximum ratings.
Do not treat an A3P125 suffix change as automatically production-equivalent. Confirm temperature grade, speed grade, qualification, and ordering format in the manufacturer's ordering information. A3P125-VQ100I is the industrial-temperature option, while the 1 and Q suffixes can indicate different ordering characteristics. Preserve the exact programmed device configuration and verify that the replacement supports the intended startup behavior.
Reserve configuration pins and clock inputs according to the family data sheet's reference design guidance, and account for every package lead even when it is unused in the current design. Route sensitive or high-fanout signals away from adjacent switching nodes, maintain a continuous ground reference, and place decoupling before branching into the FPGA supply network. This reduces return-path discontinuity and helps preserve predictable configuration and signal behavior.
Информация о соответствии
Compliance status is not stated on the cited A3P125 product page and distributor summaries. Use the manufacturer's product documentation or declarations for the selected ordering code.