Analog Devices

AD625KNZ - 25MHz Instrumentation Amplifier | Analog Devices

Артикул: AD625KNZ ✓ Активен
50 uV Vdss 16-pin PDIP Package
MOQ: 1 |

AD625KNZ Обзор

The Analog Devices AD625KNZ is a single-channel precision instrumentation amplifier with 50 uV input offset voltage, a 5 V/us slew rate, a 25 MHz gain-bandwidth product, and operation from +/-6 V to +/-18 V in a 16-pin PDIP package. It is designed for low-level differential measurement where high common-mode rejection, accurate gain control, and flexible gain settings are required.

An instrumentation amplifier is a differential amplifier optimized for amplifying small sensor signals while rejecting large common-mode voltages. In the signal-chain hierarchy, the AD625 belongs to the instrumentation-amplifier class of amplifier ICs, sitting between general-purpose operational amplifiers and application-specific measurement front ends. Its internal differential core simplifies the transition from a bridge, strain gauge, or thermocouple to a downstream ADC.

The AD625 supports precision signal conditioning through a user-selectable gain network and is suited to applications that require nonstandard gain values not easily obtained with common resistor-programmed amplifiers. Its 50 uV offset specification supports accurate low-level measurements, while the 5 V/us slew rate enables higher-amplitude output transitions without requiring a substantially faster amplifier.

The AD625 operates from dual supplies of +/-6 V through +/-18 V. Differential inputs can therefore accept substantial signal swing relative to the output reference, which is valuable when transducers produce bipolar outputs centered around ground. The 25 MHz gain-bandwidth product defines the high-frequency behavior of the amplifier, while its internal architecture determines the usable bandwidth at each closed-loop gain.

Typical uses include bridge and strain-gauge conditioning, biomedical instrumentation, current-loop receivers, laboratory measurement systems, and high-impedance sensor interfaces. The 16-pin PDIP package is suitable for through-hole assembly and prototypes, and the AD625 family provides related package and temperature options for production sourcing.

When laying out a circuit, keep the differential input traces short, symmetrical, and away from high-current switching paths. Connect the gain-setting network close to the amplifier, use a stable reference for output-referenced measurements, and follow the manufacturer pinout and reference-circuit guidance before assigning PCB tracks.

This page combines manufacturer specifications, package information, cross-reference findings, comparison parameters, and application-specific design guidance to support component selection and PCB implementation for AD625KNZ-based precision measurement circuits.

Аналоги без доработки для AD625KNZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с AD625KNZ (тот же форм-фактор и посадочное место) — отличается по Gain Configuration, Package, Common-Mode Rejection Ratio, Product Type, RoHS Status.

Analog Devices
Gain Configuration: Programmable gain
Package: 16-CDIP
Product Type: Programmable Gain Instrumentation Amplifier
Analog Devices
Gain Configuration: Programmable with an external resistor
Common-Mode Rejection Ratio: 70 dB
Product Type: Single-channel precision instrumentation amplifier
Сравнить с AD625KNZ →

AD625ADZ

✅ Прямая замена
Analog Devices
📦 16-Pin Sealed Ceramic DIP
Programmable-gain instrumentation amplifier · 1 · 1 to 10,000 · 25 MHz · 0.65 MHz · 5 V/µs · 0.02% · 5 ppm/°C

Уточнить цену

Открыть даташит →

AD625BD/+

✅ Прямая замена
Analog Devices
📦 16-Pin PDIP
Programmable Gain Instrumentation Amplifier · 1 circuit · 16-CDIP · Programmable gain · Differential input

Уточнить цену

Открыть даташит →

AD625SD

✅ Прямая замена
Analog Devices
📦 16-Pin PDIP
Programmable-gain instrumentation amplifier · 1 channel · 16-lead CDIP · 16 pins · 650 kHz · 5 V/us · 3.5 mA · 70 dB

Уточнить цену

Открыть даташит →

AD625KNZ Максимальные параметры и электрические характеристики

Device Type Single-channel precision instrumentation amplifier
Number of Channels 1 channel
Input Offset Voltage 50 uV
Slew Rate 5 V/us
Gain-Bandwidth Product 25 MHz
Low-Loss 3 dB Bandwidth 650 kHz
Supply Voltage Range +/-6 V to +/-18 V
Корпус 16-pin PDIP
Тип монтажа Through-hole
Gain Configuration User-selectable
Common-Mode Rejection Ratio 75 dB

Руководство по цоколевке AD625KNZ в корпусе 16-pin pdip

Цоколевка для AD625KNZ (корпус 16-pin pdip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 16-pin pdip для AD625KNZ

Нет подробных данных о распиновке для AD625KNZ.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

AD625KNZ подходит для 6 применениеs: Strain-Gauge and Load-Cell Bridge Conditioning, Biomedical Electrode and Physiological Signal Acquisition, Precision Current-Loop Receiver, Laboratory Instrumentation and Measurement Systems, Industrial Sensor and Transducer Interface, Audio and Low-Level AC Measurement.

🏭

Strain-Gauge and Load-Cell Bridge Conditioning

The AD625KNZ suits low-level bridge measurements because its differential input stage rejects the larger excitation-related common-mode voltage while preserving the small bridge imbalance. Its 50 uV input offset and 75 dB listed common-mode rejection support accurate conditioning of resistive strain gauges, load cells, and pressure transducers. The 5 V/us slew rate allows the output to follow dynamic mechanical events without the amplifier becoming the limiting stage. Set the gain from the specified sensitivity of the sensor, maintain a low-noise excitation reference, and keep the two input routes symmetrical to avoid degrading balance.

💊

Biomedical Electrode and Physiological Signal Acquisition

The AD625KNZ is appropriate for high-impedance physiological electrode front ends where the wanted bioelectric signal is small and common-mode interference can be much larger. Its instrumentation-amplifier topology provides differential gain in one package, reducing the number of matched discrete stages and helping preserve signal integrity. The 50 uV offset specification and +/-6 V to +/-18 V dual supply range support accurate conditioning around a zero-volt signal center. Right-drive and guarding techniques should be applied according to the manufacturer guidance, with strict attention to patient isolation requirements outside the amplifier itself.

🌐

Precision Current-Loop Receiver

The AD625KNZ can condition low-level current-loop transmitter signals when the application requires a high input impedance and strong rejection of voltage present on both sensor lines. Its differential input arrangement avoids responding to common supply and return disturbances that could otherwise obscure the measurement. The 25 MHz gain-bandwidth product and 5 V/us slew rate provide speed for sensor dynamics, while the 650 kHz listed bandwidth is generally more important for determining usable signal bandwidth. Confirm the complete input common-mode range and output swing in the manufacturer datasheet before selecting external protection components.

🔬

Laboratory Instrumentation and Measurement Systems

The AD625KNZ is well matched to laboratory instruments that combine a selectable gain with differential sensor inputs, such as analyzer front ends and programmable measurement fixtures. A single precision instrumentation amplifier simplifies the signal path compared with a multi-op-amp implementation and provides consistent common-mode behavior across multiple gain settings. Its 50 uV offset and 5 V/us slew rate support accurate low-level measurements while retaining useful response speed. For laboratory systems, stable reference connections, calibrated gain resistors, guarded analog grounds, and calibrated excitation are as important as the amplifier itself.

🏭

Industrial Sensor and Transducer Interface

The AD625KNZ provides a practical differential input stage for industrial pressure, position, and level transducers that operate with substantial common-mode voltage. The 75 dB listed common-mode rejection helps separate the useful sensor output from system-level disturbances, while the +/-6 V to +/-18 V supply range accommodates conventional bipolar analog rails. The 25 MHz gain-bandwidth product leaves headroom above the listed 650 kHz bandwidth, allowing the closed-loop gain to be selected according to the transducer response. Use shielding or differential routing when the transducer leads are long, and place protection components where they will not add significant leakage or capacitance.

🎧

Audio and Low-Level AC Measurement

The AD625KNZ can amplify low-level differential AC signals when the circuit requires controlled gain and strong rejection of common-mode pickup. Its 5 V/us slew rate provides sufficient headroom for many audio-frequency and instrumentation-band signals, while the user-selectable gain supports adaptation to different transducer sensitivities. Common-mode rejection protects the wanted channel from shared cable noise, but the final signal quality still depends on shielding, input capacitance, source impedance matching, and the gain-setting resistor network. Verify the frequency response at the intended gain rather than relying only on the 25 MHz gain-bandwidth product.

What is the AD625KNZ and what are its main specifications?
The AD625KNZ is a single-channel precision instrumentation amplifier from Analog Devices packaged in a 16-pin PDIP. According to the ADI AD625 product page and distributor technical listings, its principal characteristics include 50 uV input offset voltage, a 5 V/us slew rate, a 25 MHz gain-bandwidth product, and operation from +/-6 V to +/-18 V. It is intended for precision differential measurement in which large common-mode signals must be rejected before low-level sensor information reaches an ADC or measurement instrument.
Where can I download the AD625KNZ datasheet PDF?
The official AD625 documentation is available through the Analog Devices product page at https://www.analog.com/en/products/ad625.html, which links to the manufacturer datasheet. Third-party document mirrors also expose an AD625KNZ PDF at https://adatasheet.com/pdf/ad625knz-ad1135440. Use the Analog Devices page for the authoritative revision, while the mirror is useful as a secondary access point when the manufacturer download is temporarily unavailable.
What is the supply voltage range of the AD625KNZ?
The AD625KNZ operates from +/-6 V to +/-18 V. Dual supply operation is appropriate for bipolar sensor signals because each input can move around ground while the amplifier produces an output referenced to the output-reference pin. When designing the power rails, keep both supplies symmetrical when the signal source is ground-centered, and verify the analog and digital return paths so ground offsets do not degrade the common-mode rejection performance.
What is the gain-bandwidth product and 3 dB bandwidth of the AD625KNZ?
The AD625KNZ has a 25 MHz gain-bandwidth product, and comparison data lists a 650 kHz low-loss 3 dB bandwidth. These values describe different operating characteristics: gain-bandwidth product combines closed-loop gain with speed, while the 3 dB bandwidth identifies the frequency range over which signal amplitude begins falling materially. The usable bandwidth ultimately decreases as the selected closed-loop gain increases, so the intended gain must be included when assessing a sensor bandwidth.
Is the AD625KNZ suitable for strain-gauge and bridge measurements?
Yes, the AD625KNZ is well suited to strain-gauge and bridge measurements because its differential input architecture rejects common-mode excitation voltage while preserving the small differential bridge signal. The 50 uV input offset voltage supports low-level accuracy, and the 5 V/us slew rate provides useful headroom for dynamic bridge signals. Practical performance still depends on using matched excitation, a clean reference, and a gain-setting network that is appropriate for the required sensitivity.
What is the difference between the AD625KNZ and AD625ADZ?
The AD625KNZ and AD625ADZ are both Analog Devices AD625-family precision instrumentation amplifiers, but their order codes indicate different package and temperature options. The AD625KNZ is specified as a 16-pin PDIP, while comparison data identifies the AD625ADZ as a 16-pin sealed ceramic DIP with the same listed 650 kHz bandwidth and 5 V/us slew rate. Both can serve the same measurement function, but the mechanical package and environmental qualification differ.
When should I choose the AD625KNZ instead of the AD625ADZ?
Choose the AD625KNZ when a readily available 16-pin plastic PDIP package and a lower-cost through-hole assembly path are the priorities. Choose the AD625ADZ when the 16-pin sealed ceramic DIP construction and its associated environmental qualification are preferable. The comparison data lists the same 650 kHz bandwidth and 5 V/us slew rate for both parts, making package construction and operating-environment requirements the principal selection criteria.
Can the AD625ADZ replace the AD625KNZ on an existing PCB?
The AD625ADZ is a close AD625-family alternative in a 16-lead DIP configuration, so it can be considered for a redesign around the same instrumentation-amplifier function. However, AD625ADZ uses a sealed ceramic DIP rather than the AD625KNZ plastic PDIP, so verify the mechanical outline, soldering process, temperature grade, and lead dimensions before treating it as a drop-in substitution. Always confirm the complete pin assignment and supply requirements in the Analog Devices datasheet.
What is the best drop-in replacement for the AD625KNZ?
The AD625BD/+ is the closest same-family option identified in the cross-reference results for AD625KNZ because it retains the AD625 device identity and DIP-style package family. The AD625ADZ is another 16-pin DIP option, while the AD625SD provides a related AD625-family configuration. Confirm lead dimensions, pinout, gain network, temperature range, and qualification before committing a replacement, since order-code suffixes can change packaging and environmental ratings.
What can replace the AD625KNZ in a precision measurement design?
The AD625ADZ, AD625BD/+, and AD625SD are the relevant AD625-family replacement candidates for a precision measurement circuit. The AD625ADZ is listed as a 16-pin sealed ceramic DIP, the AD625BD/+ appears in direct AD625KNZ comparisons, and the AD625SD is shown with a 650 kHz bandwidth and 5 V/us slew rate. No verified cross-brand, pin-for-pin substitute is established, so package, pinout, and qualification checks remain essential.
How do the AD625KNZ and AD625SD differ in common-mode rejection?
Comparison data lists a common-mode rejection ratio of 75 dB for the AD625KNZ and 70 dB for the AD625SD, while both show a 650 kHz low-loss bandwidth and a 5 V/us slew rate. The AD625KNZ therefore offers 5 dB better common-mode rejection in that comparison. This difference can matter in high-gain measurements exposed to substantial common-mode voltage, although full circuit evaluation should also account for resistor tolerance, source imbalance, and frequency.
Where can I buy the AD625KNZ and what is its current lead time?
Use the Request a Quote form on this page to request current AD625KNZ availability, lead time, and a formal quotation from XAIPART. The AD625KNZ is listed as an active catalog part, and current inventory should be confirmed at order time rather than assumed from an archived listing. The same request can confirm the authorized packaging, tube quantity, and whether the 16-pin PDIP order code is available for your production schedule.
Is the AD625KNZ available in stock?
Stock status for AD625KNZ changes with distributor inventory and order volume, so confirm the current quantity through the Request a Quote form on this page. The part is listed by major component catalogs and has a 16-pin PDIP package, but catalog presence does not guarantee immediately allocable stock. Submit the required quantity, target date, and package preference with the request to obtain a current availability and lead-time response.
What are the key specifications of the AD625KNZ that engineers should know?
The key AD625KNZ specifications are a 50 uV input offset voltage, 5 V/us slew rate, 25 MHz gain-bandwidth product, 650 kHz listed 3 dB bandwidth, 75 dB listed common-mode rejection ratio, and a dual supply range of +/-6 V to +/-18 V. The device is a one-channel precision instrumentation amplifier in a 16-pin PDIP. These figures place it between ordinary operational amplifiers and dedicated measurement front ends.
Does the AD625KNZ comply with RoHS and automotive AEC-Q100 requirements?
RoHS and AEC-Q100 status for AD625KNZ should be confirmed against the current Analog Devices product documentation and the exact order code. A DIP-packaged precision instrumentation amplifier is not normally categorized as an automotive-qualified AEC-Q100 device unless explicitly listed for that grade, so automotive requirements should not be assumed from the family name. Request the manufacturer compliance and qualification statement for the specific AD625KNZ order code before releasing a regulated or automotive design.

Справочные инженерные данные для AD625KNZ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the AD625KNZ when the design requires a precision, single-channel instrumentation amplifier in a 16-pin plastic PDIP, particularly for low-level differential sensors such as strain gauges, load cells, current-loop transmitters, and laboratory probes. Its listed 50 uV offset, 75 dB common-mode rejection, 5 V/us slew rate, and 25 MHz gain-bandwidth product make it a conventional choice for high-impedance measurement front ends. Select AD625ADZ when a sealed ceramic DIP is preferable for environmental or qualification reasons and its listed speed characteristics remain acceptable. Consider AD625BD/+ when its specific temperature grade matches the required product environment and it is available in the intended sourcing channel. Consider AD625SD only when its lower listed CMRR still provides sufficient rejection. All three alternatives belong to the same manufacturer and retain closely related DIP-style construction, but final substitutions require checking pinout, temperature range, supply limits, and qualification.

Сравнение с аналогами

Параметр Этот товар AD625ADZ AD625BD/+ AD625SD
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-Pin PDIP 16-Pin Sealed Ceramic DIP 16-Pin PDIP 16-Pin PDIP
Device Type Precision Instrumentation Amplifier Precision Instrumentation Amplifier Precision Instrumentation Amplifier Precision Instrumentation Amplifier
Number of Channels 1 channel 1 channel 1 channel 1 channel

Ключевые отличия

  • Higher listed common-mode rejection than the AD625SD (против AD625SD)
  • Sealed-package option with matching listed speed (против AD625ADZ)
  • AD625-family function in a plastic PDIP configuration (против AD625BD/+)

Заметки по проектированию

Route the two differential inputs as a compact, symmetric pair and minimize their enclosed area to reduce pickup from surrounding currents. Place input protection and filtering components directly at the connector or sensor interface, while keeping the gain-setting network close to the amplifier. Provide a quiet analog return plane and route high-current outputs and switching nodes separately from the input pair.

Do not select bandwidth from the 25 MHz gain-bandwidth product alone. The listed 650 kHz low-loss bandwidth is more useful for evaluating a closed-loop configuration, and usable bandwidth decreases as gain rises. Verify the gain equation, maximum input common-mode voltage, and output swing using the manufacturer datasheet before committing resistor values and downstream ADC ranges.

Use matched, low-noise resistors in the gain network and account for source impedance balance between the two inputs. Unequal source impedances convert common-mode voltage into differential error and reduce the effective rejection ratio. For long sensor cables, use shield-driven or guarded input techniques where applicable and verify leakage from ESD or overvoltage protection against the measurement accuracy required by the application.

Bypass the supply pins close to the package and keep analog return current out of the signal-reference path. The +/-6 V to +/-18 V operating range allows conventional bipolar rails, but the exact quiescent current, allowable supply imbalance, and decoupling recommendations must be taken from the datasheet. Place a dedicated low-impedance return for each supply so output-current transients do not modulate the reference node.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

Exact compliance and qualification status must be confirmed for the specific AD625KNZ order code. A DIP-packaged precision instrumentation amplifier is not treated as an AEC-Q100 automotive-qualified device unless the manufacturer explicitly lists that qualification.

Данные проверены: 2026-11-18 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

AD625KNZ datasheet AD625KNZ datasheet pdf AD625KNZ pinout AD625KNZ specifications AD625KNZ equivalent AD625KNZ replacement AD625KNZ vs AD625ADZ AD625KNZ vs AD625SD AD625KNZ 16 pin PDIP AD625KNZ instrumentation amplifier Analog Devices AD625KNZ AD625KNZ price AD625KNZ stock AD625KNZ bridge amplifier

Связанные компоненты & термины

Analog Devices AD625KNZ AD625ADZ AD625BD/+ AD625SD precision instrumentation amplifier differential amplifier amplifier IC low-dropout regulator PSRR common-mode rejection ratio input offset voltage slew rate gain-bandwidth product 16-pin PDIP DIP package family through-hole mount strain gauge load cell bridge sensor current-loop receiver biomedical instrumentation industrial sensor interface RoHS AEC-Q100
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ