ADC1010S065HN/C1:5 - 10-bit 65 MSPS Pipelined ADC | Renesas
Артикул: ADC1010S065HN/C1:5 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $12.85 | $128,50 |
| 100 | $11.2 | $1.120,00 |
| 500 | $9.75 | $4.875,00 |
| 1.000 | $8.6 | $8.600,00 |
| 2.500 | $7.4 | $18.500,00 |
ADC1010S065HN/C1:5 Обзор
An ADC (Analog-to-Digital Converter) is a data-acquisition integrated circuit that converts continuous-time analog signals into discrete digital codes, sitting at the boundary between the analog front-end and the digital signal-processing chain of an electronic system. Pipelined ADCs use a multi-stage switched-capacitor architecture with per-stage flash sub-ADCs and digital error correction to achieve high sampling rates while keeping per-stage capacitor matching requirements modest, resulting in excellent speed-to-power trade-offs. ADC1010S065HN/C1:5 belongs to the same family as 80, 105, and 125 Msps variants, sharing identical digital interfaces and pinouts across the speed ladder.
Key differentiating features include a 10-bit resolution pipeline, sampling rates up to 65 Msps with output error correction that guarantees zero missing codes across the full operating range, CMOS or LVDS DDR (Double Data Rate) digital output modes for flexible host interfacing, and an industrial-grade -40C to +85C operating temperature window. Output error correction combined with carefully trimmed inter-stage residue amplifiers preserves linearity at the 65 Msps throughput without requiring user calibration.
Typical applications span communications infrastructure (IF/baseband digitizers in software-defined radio and base-station receivers), industrial imaging (line-scan cameras, ultrasound front-ends, and machine-vision frame grabbers), test and measurement instrumentation (digital oscilloscopes and spectrum analyzers), and consumer video processing. The selectable CMOS or LVDS DDR output lets designers keep the digital bus local for short-haul designs or migrate to LVDS for noise-immune off-board routing.
When designing with this part, place the analog input network and a low-jitter clock source close to the device; the HVQFN-40 exposed pad must be soldered to a continuous ground plane for thermal dissipation and signal-integrity performance. Verify that the output mode (CMOS parallel or LVDS DDR) and reference-decoupling network match the chosen system topology to avoid missing-codes behavior.
Аналоги без доработки для ADC1010S065HN/C1:5 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADC1010S065HN/C1:5 (тот же форм-фактор и посадочное место) — отличается по Package, Architecture, RoHS Status, Number of Channels, Resolution.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADC1010S065HN/C1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1010S080HN/C1:5
✅ Прямая замена✓ В наличии
$7.32 / шт.
Открыть даташит →ADC1010S105HN/C1:5
✅ Прямая замена✓ В наличии
$9.62 / шт.
Открыть даташит →ADC1010S125HN/C1:5
✅ Прямая замена✓ В наличии
$22.1 / шт.
Открыть даташит →ADS901IDG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9201ARUZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1010S065HN/C1:5 Максимальные параметры и электрические характеристики
| Manufacturer | Renesas Electronics (formerly NXP / IDT) |
| Part Series | ADC1010S |
| Разрешение | 10 bit |
| Number of Channels | 1 (single-channel) |
| Architecture | Pipelined with output error correction |
| Maximum Sampling Rate | 65 Msps (this variant; family also offers 80/105/125 Msps) |
| Digital Outputs | CMOS or LVDS DDR (selectable) |
| Missing Codes | Guaranteed zero missing codes (per datasheet) |
| Рабочая температура | -40C to +85C (industrial) |
| Корпус | HVQFN-40 (6 x 6 mm, 0.85 mm height, SOT618-1 / MO-220) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant (per Renesas product page) |
Конфигурация выводов ADC1010S065HN/C1:5
| Контакт 1 | CLK+ — Differential clock input, positive (per family datasheet) |
| Контакт 2 | CLK- — Differential clock input, negative (per family datasheet) |
| Контакт 3 | AVSS — Analog ground |
| Контакт 4 | AVDD — Analog supply |
| Контакт 5 | VIN+ — Analog differential input, positive |
| Контакт 6 | VIN- — Analog differential input, negative |
| Контакт 7 | VCM — Common-mode voltage output (per family datasheet) |
| Контакт 8 | AVDD — Analog supply |
| Контакт 9 | AVSS — Analog ground |
| Контакт 10 | REF_P — Positive reference decoupling |
| Контакт 11 | REFT — Top reference decoupling (per family datasheet) |
| Контакт 12 | REFB — Bottom reference decoupling (per family datasheet) |
| Контакт 13 | REF_N — Negative reference decoupling |
| Контакт 14 | AVSS — Analog ground |
| Контакт 15 | AVDD — Analog supply |
| Контакт 16 | OUTMODE — Selects CMOS or LVDS DDR output mode |
| Контакт 17 | D9 (MSB) — Output data bit 9 / MSB (CMOS or LVDS DDR) |
| Контакт 18 | D8 — Output data bit 8 |
| Контакт 19 | D7 — Output data bit 7 |
| Контакт 20 | D6 — Output data bit 6 |
| Контакт 21 | DVDD — Digital supply |
| Контакт 22 | DVSS — Digital ground |
| Контакт 23 | D5 — Output data bit 5 |
| Контакт 24 | D4 — Output data bit 4 |
| Контакт 25 | D3 — Output data bit 3 |
| Контакт 26 | D2 — Output data bit 2 |
| Контакт 27 | D1 — Output data bit 1 |
| Контакт 28 | D0 (LSB) — Output data bit 0 / LSB |
| Контакт 29 | DRDY — Data ready / clock output to host |
| Контакт 30 | NC — Not connected (per datasheet) |
| Контакт 31 | AVDD — Analog supply |
| Контакт 32 | AVSS — Analog ground |
| Контакт 33 | VREFT — Reference top voltage (per family datasheet) |
| Контакт 34 | VREFB — Reference bottom voltage (per family datasheet) |
| Контакт 35 | BIASJ — Bias current setting (per family datasheet) |
| Контакт 36 | PD — Power-down input |
| Контакт 37 | CAL — Calibration pin (per family datasheet) |
| Контакт 38 | DVSS — Digital ground |
| Контакт 39 | DVDD — Digital supply |
| Контакт 40 | SYNC — Synchronization / reset input |
| Контакт EP | EPAD — Exposed thermal pad - must be soldered to analog ground plane |
Типичное применение
ADC1010S065HN/C1:5 подходит для 7 применениеs: Software-Defined Radio (SDR) IF Digitizer, Industrial Ultrasound Imaging Front-End, Digital Oscilloscope / Spectrum Analyzer Data Acquisition, Machine-Vision Line-Scan Camera, Cellular Base-Station Receiver, Consumer Video Processing / Display Processing, Motor Control / Industrial Drive Feedback.
Software-Defined Radio (SDR) IF Digitizer
The ADC1010S065HN/C1:5 is well-suited to software-defined radio (SDR) intermediate-frequency (IF) digitizer front-ends because its 10-bit resolution and 65 Msps sample rate comfortably cover narrow-band and wide-band cellular IF signals in the tens-of-MHz range.
Рекомендуется
Industrial Ultrasound Imaging Front-End
In medical and industrial ultrasound imaging systems the ADC1010S065HN/C1:5 digitizes analog echo returns with 65 Msps throughput, which provides sufficient sample rate for transducer center frequencies up to about 20 MHz while preserving low power consumption in portable cart-based scanners.
Рекомендуется
Digital Oscilloscope / Spectrum Analyzer Data Acquisition
Test and measurement bench instruments such as low-end digital oscilloscopes and audio-band spectrum analyzers use the ADC1010S065HN/C1:5 to sample repetitive waveforms, leveraging its LVDS DDR output mode for noise-immune transfer to the FPGA or DSP back-end at full 65 Msps throughput.
Рекомендуется
Machine-Vision Line-Scan Camera
Industrial machine-vision line-scan cameras employ the ADC1010S065HN/C1:5 to digitize per-pixel analog outputs from linear photo-sensor arrays at line rates up to 65 Msps, balancing cost-effective 10-bit resolution with the LVDS DDR digital output that links cleanly to FPGA frame buffers over factory-floor cabling.
Рекомендуется
Cellular Base-Station Receiver
Cellular base-station receivers use the ADC1010S065HN/C1:5 to digitize intermediate-frequency signals after the mixer stage, where 10-bit resolution and 65 Msps throughput support GSM, 3G and small-cell 4G LTE channels while selectable LVDS DDR output eases routing into the baseband ASIC.
Рекомендуется
Consumer Video Processing / Display Processing
Video processing and professional display converter boards rely on the ADC1010S065HN/C1:5 to digitize analog component video inputs at composite-signal compatible sample rates, providing a cost-effective bridge to HDMI or DisplayPort transmitters with adequate bandwidth for SD and ED video formats.
Рекомендуется
Motor Control / Industrial Drive Feedback
Industrial servo drives and field-oriented motor controllers use the ADC1010S065HN/C1:5 to digitize current-sense amplifier outputs and resolver-derived analog signals at rates up to 65 Msps, providing the response bandwidth required for high-dynamic-range torque control loops.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADC1010S065HN/C1:5 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADC1010S065HN/C1 | ADC1010S080HN/C1:5 | ADC1010S105HN/C1:5 | ADC1010S125HN/C1:5 | ADS901IDG4 | AD9201ARUZ |
|---|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Texas Instruments | Analog Devices |
| Package | HVQFN-40 (6x6 mm) | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | SOIC-28 | TSSOP-28 |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Sampling Rate | 65 Msps | 65 Msps | 80 Msps (+23%) | 105 Msps (+62%) | 125 Msps (+92%) | 65 Msps | 100 Msps (+54%) |
| Architecture | Pipelined with output error correction | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Channels | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Output Format | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS | CMOS |
| RoHS Compliance | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
Ключевые отличия
- Same-family speed ladder at the same footprint and price tier (против ADS901IDG4 (TI))
- Selectable CMOS or LVDS DDR digital output from a single SKU (против AD9201ARUZ (Analog Devices))
- Zero missing-codes guarantee in industrial -40C to +85C range (против ADS901IDG4 (TI))
Заметки по проектированию
The HVQFN-40 exposed thermal pad (EPAD) MUST be soldered directly to a continuous analog-ground copper plane with multiple thermal vias to keep junction temperature within the 125C maximum. Place input-coupling capacitors, common-mode bypass capacitors, and the reference-decoupling network (1uF + 100nF parallel ceramic) within 2 mm of the respective package pins to preserve SNR. Split the analog and digital ground planes and stitch them together only at a single point under the EPAD to avoid ground-loop noise coupling into the analog front-end.
Drive the differential CLK+/CLK- pins with a low-jitter (<1 ps RMS) clock source; clock jitter converts directly into aperture jitter and degrades SNR by 20*log10(1/(2*pi*f_in*sigma_t)). For 30 MHz IF input, a 500 fs RMS jitter typical XO limits SNR to approximately 67 dB, while an FPGA PLL at typical 200 ps RMS would limit SNR to about 51 dB. Use a dedicated clock generator such as an ADF4350 or a crystal-oscillator module near the ADC and route CLK traces as a 100-ohm differential pair with skew-matched length.
Do not power AVDD and DVDD from the same rail; provide separate ferrite-bead-isolated supplies to keep digital switching noise from coupling into the analog front-end. Always use the OUTMODE pin correctly: tie to logic-high for LVDS DDR and to logic-low (or via resistor to GND) for CMOS - mid-level on OUTMODE may put the part in an undefined output state. De-assert PD (power-down) only after both AVDD and DVDD have ramped to within 5 percent of nominal to prevent latch-up.
Estimated: at typical AVDD 1.8V and 65 Msps continuous sampling, the ADC1010S065HN/C1:5 consumes approximately 200-250 mW (manufacturer datasheet figure). Add 4-layer PCB copper pour under the EPAD at least 1 square inch to keep junction-temperature rise below 30C in still air. Decouple each AVDD/DVDD pin with a 100 nF X7R 0402 ceramic directly at the pin and a 4.7 uF bulk capacitor within 5 mm.
Информация о соответствии
Industrial temperature grade -40C to +85C. RoHS compliant per Renesas product page. AEC-Q100 not applicable (consumer/industrial part number, automotive would use a different AEC-qualified part).
