ADC1213S065HN-C1 - 12-bit 65 MSPS Single-Channel ADC | Renesas
Артикул: ADC1213S065HN-C1 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $23.5 | $23,50 |
| 10 | $21.2 | $212,00 |
| 100 | $18.75 | $1.875,00 |
| 500 | $16.4 | $8.200,00 |
| 1.000 | $14.95 | $14.950,00 |
ADC1213S065HN-C1 Обзор
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous analog input voltages into discrete digital codes at a defined sampling rate. High-speed ADCs such as the ADC1213S065HN-C1 sit between the analog front-end (amplifiers, filters, mixers) and the digital signal processor or FPGA in communications, instrumentation, and defense systems. The 12-bit resolution and 65 MSPS throughput position it in the mid-resolution, mid-speed segment where dynamic range and SFDR matter more than raw bit count.
Key features of the ADC1213S065HN-C1 include a 12-bit resolution, 65 MSPS maximum sampling rate, single-channel differential input, JESD204A serial output interface, low-power CMOS architecture, and an industrial operating temperature range of -40C to +85C. The HVQFN-32 package measures 7 x 7 mm with 0.80 mm height, providing a small PCB footprint suitable for space-constrained designs.
The device uses a pipelined architecture with internal reference and on-chip sample-and-hold. The JESD204A serial interface reduces I/O count versus parallel LVDS, simplifying board routing when interfacing to FPGAs or ASICs that include JESD204A link layers. Compared with parallel-output ADCs of similar speed, the part offers fewer board traces, lower pin count, and built-in deterministic latency.
Typical applications include software-defined radio (SDR), wireless infrastructure base stations, radar and lidar digitizers, medical imaging, and high-speed data acquisition. The combination of 12-bit resolution and 65 MSPS is well-matched to intermediate-frequency (IF) sampling in communications receivers and to multi-channel oscilloscope front-ends.
Designers should note that the ADC1213S065HN-C1 requires a clean, low-jitter sampling clock and a differential analog input drive. Decoupling and PCB layout for the HVQFN exposed pad are critical; the EP must be soldered to a low-impedance ground plane to meet the published SNR/SFDR performance.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone, giving engineers a single reference for part selection, sourcing, and PCB-level integration.
Аналоги без доработки для ADC1213S065HN-C1 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADC1213S065HN-C1 (тот же форм-фактор и посадочное место) — отличается по Package, Resolution, Number of Channels, Architecture, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADC1213S080HN-C1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1213S105HN-C1
✅ Прямая замена✓ В наличии
$9.9 / шт.
Открыть даташит →ADC1213S125HN-C1
✅ Прямая замена✓ В наличии
$18.45 / шт.
Открыть даташит →ADC1015S125HN/C1
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →ADC1010S065HN/C1:5
✅ Прямая замена✓ В наличии
$7.4 / шт.
Открыть даташит →ADC1213S065HN-C1 Максимальные параметры и электрические характеристики
| Разрешение | 12 bits |
| Number of Channels | 1 (single) |
| Maximum Sample Rate | 65 MSPS |
| Input Type | Differential |
| Data Interface | Serial JESD204A |
| Architecture | Pipelined CMOS |
| Корпус | HVQFN-32 (SOT1152-1) 7x7 mm |
| Package Height | 0.80 mm |
| Рабочая температура | -40 C to +85 C (Industrial) |
| Screening Level | Industrial |
| Тип монтажа | Surface Mount |
| Order Code Suffix | -C1 (tray packaging) |
| Число выводов | 32 |
| Exposed Pad (EP) | Yes (must be soldered to GND plane) |
| Статус RoHS | Compliant |
Конфигурация выводов ADC1213S065HN-C1
| Контакт 1 | IN+ — Differential analog input (positive) |
| Контакт 2 | IN- — Differential analog input (negative) |
| Контакт 3 | VCM — Common-mode voltage output |
| Контакт 4 | AVDD — Analog 3.3V supply |
| Контакт 5 | AGND — Analog ground |
| Контакт 6 | AVDD — Analog 3.3V supply |
| Контакт 7 | AGND — Analog ground |
| Контакт 8 | REFIN — External reference input |
| Контакт 9 | REFOUT — Internal reference output |
| Контакт 10 | AGND — Analog ground |
| Контакт 11 | AVDD — Analog 3.3V supply |
| Контакт 12 | CLK+ — Differential clock input (positive) |
| Контакт 13 | CLK- — Differential clock input (negative) |
| Контакт 14 | AGND — Analog ground |
| Контакт 15 | DRVDD — Digital driver supply |
| Контакт 16 | DRGND — Digital driver ground |
| Контакт 17 | SYNC~ — JESD204A sync request (active low) |
| Контакт 18 | SENSE — JESD204A sense / config |
| Контакт 19 | RESET — Chip reset (active low) |
| Контакт 20 | PD — Power-down control |
| Контакт 21 | DBP — Test / bypass pin |
| Контакт 22 | NC — Not connected (per datasheet) |
| Контакт 23 | DOUT_N — JESD204A serial data (negative lane) |
| Контакт 24 | DOUT_P — JESD204A serial data (positive lane) |
| Контакт 25 | DRGND — Digital driver ground |
| Контакт 26 | DRVDD — Digital driver supply |
| Контакт 27 | AGND — Analog ground |
| Контакт 28 | AVDD — Analog 3.3V supply |
| Контакт 29 | AGND — Analog ground |
| Контакт 30 | AVDD — Analog 3.3V supply |
| Контакт 31 | NC — Not connected (per datasheet) |
| Контакт 32 | NC — Not connected (per datasheet) |
Типичное применение
ADC1213S065HN-C1 подходит для 6 применениеs: Software-Defined Radio (SDR) IF Sampling, Wireless Base Station Receiver, Radar and Lidar Digitizer Front-End, Medical Ultrasound Imaging, High-Speed Data Acquisition Systems, Test and Measurement Instrumentation.
Software-Defined Radio (SDR) IF Sampling
The ADC1213S065HN-C1 digitizes intermediate-frequency (IF) signals in software-defined radio receivers, where its 12-bit resolution and 65 MSPS throughput deliver sufficient dynamic range for narrowband and wideband channel decoding. With 12 bits at 65 MSPS, the converter provides about 71 dB SNR, comfortably handling QAM and OFDM demodulation when paired with a low-jitter clock. The JESD204A serial output links directly to Xilinx or Altera FPGAs, reducing board trace count versus parallel LVDS and simplifying multi-channel synchronization across antenna arrays.
Рекомендуется
Wireless Base Station Receiver
In LTE and 5G small-cell base-station receivers, the ADC1213S065HN-C1 samples the IF output of the down-conversion stage with 12-bit accuracy and 65 MSPS throughput, sufficient for up to 30 MHz signal bandwidth per channel. The pipelined CMOS architecture provides high SFDR (>75 dBFS typical) for clean digital demodulation, while the JESD204A interface ensures deterministic latency needed for MIMO synchronization. The HVQFN-32 7x7 mm package allows compact receiver card layouts with up to four channels per board.
Рекомендуется
Radar and Lidar Digitizer Front-End
The ADC1213S065HN-C1 digitizes wideband return pulses in short-range radar and lidar systems where 12-bit resolution at 65 MSPS is adequate for sub-meter range resolution. The single-channel input pairs with a low-noise differential amplifier front-end, and the JESD204A link streams samples to a Xilinx Kintex or Spartan FPGA for matched-filter pulse compression. Industrial -40C to +85C temperature range supports outdoor automotive and surveillance deployments without derating.
Рекомендуется
Medical Ultrasound Imaging
In portable ultrasound probes, the ADC1213S065HN-C1 samples the receive beamformer output at 12 bits and 65 MSPS, providing sufficient dynamic range for B-mode imaging at depths up to 15 cm. The low-power CMOS architecture helps meet battery-life targets in handheld scanners, while the JESD204A output simplifies high-density probe cables. Its small HVQFN-32 7x7 mm footprint leaves board area for multi-element array electronics, and the industrial temperature range supports clinical and field use.
Рекомендуется
High-Speed Data Acquisition Systems
The ADC1213S065HN-C1 fits PCI Express and USB-3 modular DAQ boards where 12-bit vertical resolution and 65 MSPS real-time sample rate address mainstream oscilloscope, vibration, and transient-recording applications. Differential inputs reject common-mode noise from industrial sensors, while the JESD204A serial output streams data over a single high-speed lane to an FPGA-based capture buffer. The 32-pin HVQFN package keeps the analog front-end area compact on 4-layer PCBs typical of modular instruments.
Рекомендуется
Test and Measurement Instrumentation
Benchtop spectrum analyzers and digitizers leverage the ADC1213S065HN-C1 for its 12-bit resolution and 65 MSPS throughput, which deliver sufficient spurious-free dynamic range for production-line signal analyzers and automated test equipment. The JESD204A interface allows multiple ADCs to be synchronized through deterministic latency for phase-coherent measurements, while the HVQFN-32 footprint supports dense multi-channel front-end designs. Industrial temperature screening supports use in semi-fab and outdoor telecom test gear.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADC1213S065HN-C1 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADC1213S080HN-C1 | ADC1213S105HN-C1 | ADC1213S125HN-C1 | ADC1015S125HN/C1 | ADC1010S065HN/C1:5 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | HVQFN-32 (SOT1152-1) 7x7 mm | HVQFN-32 (SOT1152-1) - same | HVQFN-32 (SOT1152-1) - same | HVQFN-32 (SOT1152-1) - same | HVQFN-32 - same family | HVQFN-32 - same family |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 10 bits | 10 bits |
| Maximum Sample Rate | 65 MSPS | 80 MSPS | 105 MSPS | 125 MSPS | 125 MSPS | 65 MSPS |
| Number of Channels | 1 (single) | 1 | 1 | 1 | 1 | 1 |
| Digital Interface | JESD204A | JESD204A | JESD204A | JESD204A | JESD204A | JESD204A |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Ключевые отличия
- Lowest-cost entry point in the ADC1213S family (против ADC1213S125HN-C1)
- Higher dynamic range at given sample rate (против ADC1010S065HN/C1:5)
- JESD204A output reduces board complexity (против Parallel-LVDS ADCs of similar speed)
Заметки по проектированию
The HVQFN-32 (SOT1152-1) package has an exposed thermal pad that must be soldered to a low-impedance ground plane with multiple thermal vias. Use at least 9 thermal vias in a 3x3 array under the EP for heat extraction. Separate analog and digital ground planes and join them at a single point under the IC to avoid digital switching noise coupling into the analog front-end.
Drive the differential analog input (IN+/IN-) with a low-noise differential amplifier (e.g., a transformer driver or fully-differential op-amp) to preserve SFDR. The clock input (CLK+/CLK-) must be driven by a low-jitter (<200 fs RMS) source, because aperture jitter directly limits SNR at high input frequencies. A high-Q LVDS or LVPECL clock driver is recommended for best performance at 65 MSPS.
Estimated: at 65 MSPS, the ADC1213S065HN-C1 typically draws around 250-300 mA from AVDD and 50-80 mA from DRVDD. Decouple AVDD with a 10 uF bulk capacitor plus 0.1 uF and 10 nF ceramics placed as close as possible to each supply pin. Use a ferrite bead or pi-filter between the analog and digital 3.3V rails to suppress switching noise from the JESD204A output driver.
Do not leave the exposed pad floating; this destroys thermal performance and can cause high jitter or dropped codes. Ensure the JESD204A link is properly initialized through SYNC~ handshake with the receiving FPGA before valid data appears on DOUT_P/DOUT_N. Avoid routing the JESD204A serial lane over splits in the reference plane - use a continuous GND reference under the lane for 100 ohm differential impedance.
Информация о соответствии
RoHS and REACH compliance per Renesas product page. Industrial screening level only - no AEC-Q100 automotive grade variant in the ADC1213S family. Halogen-free and conflict-mineral status not stated in the verified web data.
