ATMEGA2561-16MU - 8-bit AVR MCU 256KB Flash 16MHz 64-QFN | Microchip
Артикул: ATMEGA2561-16MU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $17.95 | $17,95 |
| 10 | $16.21 | $162,10 |
| 100 | $14.27 | $1.427,00 |
| 500 | $12.96 | $6.480,00 |
| 1.000 | $11.83 | $11.830,00 |
ATMEGA2561-16MU Обзор
An AVR microcontroller (sometimes called an Advanced Virtual RISC microcontroller) is a single-chip computer built around the Atmel AVR 8-bit RISC core, executing most instructions in a single clock cycle to deliver deterministic throughput. ATmega2561 belongs to the megaAVR family, sitting between tinyAVR and XMEGA in Microchip's 8-bit hierarchy, and is commonly used where higher pin count and larger memory are needed without moving to 32-bit ARM Cortex-M parts.
Key features of the ATMEGA2561-16MU include 256 KB self-programmable Flash with Read-While-Write support, 8 KB on-chip SRAM, 4 KB true EEPROM with 100,000 erase/write cycles endurance, an internal calibrated RC oscillator, and six software-selectable power-saving modes that can reduce active current to microampere levels for battery-operated designs. The 8-channel 10-bit successive-approximation ADC delivers up to 15 kSPS at full resolution, and the on-chip analog comparator supports single-ended and differential inputs with selectable hysteresis.
Architecturally, the ATMEGA2561 uses a Harvard-style memory layout with separate program Flash and data SRAM buses, a hardware multiplier supporting signed/unsigned multiply and fractional multiply instructions, and a deterministic interrupt controller with up to 57 interrupt vectors. The peripheral interconnect allows timer/counter outputs to drive ADC triggers and PWM channels, enabling motor control and power-conversion topologies without software overhead.
Typical applications include industrial automation controllers, building automation gateways, smart energy metering, USB-to-UART bridges using external PHY, multi-channel data acquisition front-ends, robotic controller boards, automotive body and infotainment subsystems (when properly qualified), and hobbyist/education platforms such as Arduino-Mega-compatible designs. The wide memory and I/O count also make it a frequent fit for SCADA remote terminal units (RTUs).
When designing with this device, ensure decoupling follows Microchip's recommended 100 nF ceramic on each VCC pin plus a 10 uF bulk, and respect the 5.5 V absolute-maximum VCC rating even though the part is 5 V tolerant. JTAG and ISP programming both require the RESET pin to remain in a defined state; for noise immunity, place a 10 kohm pull-up on RESET and a low-value decoupling capacitor on AVCC to maximize ADC linearity.
This page synthesizes distributor inventory, 64-QFN drop-in alternatives, and practical AVR design notes not found in the manufacturer datasheet alone, accelerating part selection and PCB re-use.
Аналоги без доработки для ATMEGA2561-16MU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA2561-16MU (тот же форм-фактор и посадочное место) — отличается по Package, USART, Timers/Counters, ADC, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA2561-16MUR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA2561-16AU
✅ Прямая замена✓ В наличии
$11.95 / шт.
Открыть даташит →ATMEGA2561-16AI
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA1281-16MUR
✅ Прямая замена✓ В наличии
$8.78 / шт.
Открыть даташит →ATMEGA1281-16MUR
✅ Прямая замена✓ В наличии
$8.78 / шт.
Открыть даташит →ATMEGA1281-16AU
✅ Прямая замена✓ В наличии
$8.27 / шт.
Открыть даташит →ATMEGA2561-16MU Максимальные параметры и электрические характеристики
| Core Architecture | AVR 8-bit RISC |
| Maximum CPU Frequency | 16 MHz |
| MIPS Throughput | 16 MIPS |
| Program Flash Memory | 256 KB (128K x 16) |
| SRAM | 8 KB |
| EEPROM | 4 KB |
| Operating Voltage (VCC) | 4.5 V to 5.5 V |
| Programmable I/O Lines | 54 |
| General-Purpose Working Registers | 32 |
| ADC | 8-channel, 10-bit |
| USART | 4 channels |
| SPI | 1 channel (Master/Slave) |
| TWI (I2C) | 1 channel (byte-oriented) |
| Timer/Counters | 2x 8-bit + 4x 16-bit with PWM |
| Watchdog Timer | Yes, with separate on-chip oscillator |
| Analog Comparator | On-chip, with selectable hysteresis |
| JTAG Debug Interface | Yes (boundary-scan capable) |
| External Memory Interface (EBI/EMI) | Yes |
| Корпус | 64-VFQFN (9x9 mm) with exposed pad |
| Рабочая температура | -40 C to +85 C (industrial) |
| Тип монтажа | Surface Mount |
| Lead-Free / RoHS | Yes / Compliant |
Конфигурация выводов ATMEGA2561-16MU
| Контакт 1 | VCC — Digital supply voltage |
| Контакт 2 | PE0 (RXD0/PCINT8) — Port E bit 0, USART0 RXD, pin-change interrupt |
| Контакт 3 | PE1 (TXD0) — Port E bit 1, USART0 TXD |
| Контакт 4 | PE2 (AIN0/XCK0) — Port E bit 2, analog comparator input, USART0 XCK |
| Контакт 5 | PE3 (AIN1/OC3A) — Port E bit 3, analog comparator input, timer output compare |
| Контакт 6 | PE4 (INT4/OC3B) — Port E bit 4, external interrupt, timer output compare |
| Контакт 7 | PE5 (INT5/OC3C) — Port E bit 5, external interrupt, timer output compare |
| Контакт 8 | PE6 (INT6/TCLK3) — Port E bit 6, external interrupt, timer clock input |
| Контакт 9 | PE7 (INT7/ICP3) — Port E bit 7, external interrupt, timer input capture |
| Контакт 10 | VCC — Digital supply voltage |
| Контакт 11 | GND — Ground |
| Контакт 12 | PH0 (RXD2) — Port H bit 0, USART2 RXD |
| Контакт 13 | PH1 (TXD2) — Port H bit 1, USART2 TXD |
| Контакт 14 | PH2 (XCK2) — Port H bit 2, USART2 XCK |
| Контакт 15 | PH3 (OC4A) — Port H bit 3, timer output compare |
| Контакт 16 | PH4 (OC4B) — Port H bit 4, timer output compare |
| Контакт 17 | PH5 (OC4C) — Port H bit 5, timer output compare |
| Контакт 18 | PH6 (OC2B) — Port H bit 6, timer output compare |
| Контакт 19 | PH7 (OC2A) — Port H bit 7, timer output compare |
| Контакт 20 | PB0 (SS/PCINT0) — Port B bit 0, SPI slave select, pin-change interrupt |
| Контакт 21 | PB1 (SCK/PCINT1) — Port B bit 1, SPI clock, pin-change interrupt |
| Контакт 22 | PB2 (MOSI/PCINT2) — Port B bit 2, SPI MOSI, pin-change interrupt |
| Контакт 23 | PB3 (MISO/PCINT3) — Port B bit 3, SPI MISO, pin-change interrupt |
| Контакт 24 | PB4 (OC0A/PCINT4) — Port B bit 4, timer output compare, pin-change interrupt |
| Контакт 25 | PB5 (OC1A/PCINT5) — Port B bit 5, timer output compare, pin-change interrupt |
| Контакт 26 | PB6 (OC1B/PCINT6) — Port B bit 6, timer output compare, pin-change interrupt |
| Контакт 27 | PB7 (OC0B/OC1C/PCINT7) — Port B bit 7, timer output compare, pin-change interrupt |
| Контакт 28 | VCC — Digital supply voltage |
| Контакт 29 | GND — Ground |
| Контакт 30 | AVCC — Analog supply voltage (for ADC) |
| Контакт 31 | AREF — ADC reference voltage |
| Контакт 32 | GND — Ground |
| Контакт 33 | PF0 (ADC0) — Port F bit 0, ADC input channel 0 |
| Контакт 34 | PF1 (ADC1) — Port F bit 1, ADC input channel 1 |
| Контакт 35 | PF2 (ADC2) — Port F bit 2, ADC input channel 2 |
| Контакт 36 | PF3 (ADC3) — Port F bit 3, ADC input channel 3 |
| Контакт 37 | PF4 (ADC4/TCK) — Port F bit 4, ADC input, JTAG TCK |
| Контакт 38 | PF5 (ADC5/TMS) — Port F bit 5, ADC input, JTAG TMS |
| Контакт 39 | PF6 (ADC6/TDO) — Port F bit 6, ADC input, JTAG TDO |
| Контакт 40 | PF7 (ADC7/TDI) — Port F bit 7, ADC input, JTAG TDI |
| Контакт 41 | PA0 (AD0) — Port A bit 0, external memory address/data |
| Контакт 42 | PA1 (AD1) — Port A bit 1, external memory address/data |
| Контакт 43 | PA2 (AD2) — Port A bit 2, external memory address/data |
| Контакт 44 | PA3 (AD3) — Port A bit 3, external memory address/data |
| Контакт 45 | PA4 (AD4) — Port A bit 4, external memory address/data |
| Контакт 46 | PA5 (AD5) — Port A bit 5, external memory address/data |
| Контакт 47 | PA6 (AD6) — Port A bit 6, external memory address/data |
| Контакт 48 | PA7 (AD7) — Port A bit 7, external memory address/data |
| Контакт 49 | PG2 (ALE) — Port G bit 2, external memory address latch enable |
| Контакт 50 | VCC — Digital supply voltage |
| Контакт 51 | GND — Ground |
| Контакт 52 | PG1 (RD) — Port G bit 1, external memory read strobe |
| Контакт 53 | PG0 (WR) — Port G bit 0, external memory write strobe |
| Контакт 54 | PD7 (SDA) — Port D bit 7, TWI I2C data |
| Контакт 55 | PD6 (SCL) — Port D bit 6, TWI I2C clock |
| Контакт 56 | PD5 (XCK1) — Port D bit 5, USART1 XCK |
| Контакт 57 | PD4 (ICP1) — Port D bit 4, timer1 input capture |
| Контакт 58 | PD3 (INT3/TXD1) — Port D bit 3, external interrupt, USART1 TXD |
| Контакт 59 | PD2 (INT2/RXD1) — Port D bit 2, external interrupt, USART1 RXD |
| Контакт 60 | PD1 (INT1/SDA) — Port D bit 1, external interrupt, I2C data alt |
| Контакт 61 | PD0 (INT0/SCL) — Port D bit 0, external interrupt, I2C clock alt |
| Контакт 62 | RESET — Reset input, active low |
| Контакт 63 | VCC — Digital supply voltage |
| Контакт 64 | GND — Ground |
| Контакт 65 | EPAD — Exposed thermal pad (connect to ground for thermal dissipation) |
Типичное применение
ATMEGA2561-16MU подходит для 6 применениеs: Industrial Automation Controllers, Building Automation Gateways, Smart Energy Metering Front-Ends, Robotic Controller Boards, Multi-Channel Data Acquisition Front-Ends, SCADA Remote Terminal Units (RTUs).
Industrial Automation Controllers
The ATMEGA2561-16MU is well-matched to industrial PLC, HMI, and remote-I/O designs because its 54 programmable I/O lines can drive relays, optocouplers, and isolated digital inputs simultaneously, while four USARTs bridge RS-232, RS-485, and RS-422 field buses in parallel. The 16 MIPS core executes PID loops at sub-millisecond rates, and the 8-channel 10-bit ADC samples up to 15 kSPS for thermocouple or 4-20 mA signal conditioning front-ends. Its -40 C to +85 C industrial temperature range plus 256 KB Flash allows a single MCU to host both the application logic and a Modbus-RTU or Modbus-TCP stack, eliminating an external communications processor. Brown-out detect and watchdog timer with independent oscillator improve field reliability against brown-out and firmware lock-up events.
Рекомендуется
Building Automation Gateways
The ATMEGA2561-16MU suits BACnet, KNX, or Modbus gateway designs where the MCU must convert between multiple building-automation field buses concurrently. Its four hardware USARTs allow simultaneous RS-485 trunks at different baud rates, while the I2C and SPI ports connect to onboard sensors or radio modules. The 256 KB Flash stores the full protocol stack plus custom mapping logic, while the 4 KB EEPROM stores device bindings and configuration that must survive power cycles. Operating from 4.5 V to 5.5 V makes the part easy to integrate with 5 V supply rails common in HVAC control panels, and the 64-VFQFN footprint leaves room for optoisolator channels around the MCU.
Рекомендуется
Smart Energy Metering Front-Ends
The ATMEGA2561-16MU fits single-phase and three-phase energy metering front-ends because its 8-channel 10-bit ADC measures voltage and current CT/PT-derived signals, while its 16-bit timer/counters capture pulse-output from dedicated metrology ICs. The 256 KB Flash hosts the metrology algorithm plus DLMS/COSEM or ANSI C12.18/19 stack, and the 4 KB EEPROM stores tariff schedules and calibration constants. Its four USARTs support optical port, RS-485, and PLC-modem interfaces simultaneously. Operating from 4.5 V to 5.5 V and -40 C to +85 C meets outdoor cabinet requirements when paired with proper conformal coating and isolation barriers.
Рекомендуется
Robotic Controller Boards
Robotic controllers benefit from the ATMEGA2561-16MU's six timer/counter channels capable of multi-channel PWM at up to 16-bit resolution for servo and BLDC motor drive signals. The 16 MIPS throughput handles inverse kinematics and PID loop computation at hundreds of Hz without DSP acceleration, and the 8-channel ADC reads encoder feedback, current sense, and battery monitor channels. Its four USARTs expose debug, GPS, IMU, and radio links simultaneously. The 64-VFQFN package plus 5 V tolerance simplify integration with hobby-grade sensors and drivers, making this MCU a popular choice for educational and maker robotic platforms including Arduino-Mega-derived designs.
Рекомендуется
Multi-Channel Data Acquisition Front-Ends
The ATMEGA2561-16MU is a strong fit for low-speed multi-channel data loggers where its 8-channel 10-bit ADC (with optional internal 1.1 V reference) samples analog sensor channels while the on-chip USARTs offload data to a host. The 256 KB Flash stores local buffering and compression routines, and the 4 KB EEPROM retains calibration and time-stamp tables. The 64-VFQFN package's exposed thermal pad helps dissipate heat when the ADC and digital I/O run continuously. JTAG support enables in-field firmware updates during commissioning, and brown-out detect plus watchdog improve robustness against supply transients in field installations.
Рекомендуется
SCADA Remote Terminal Units (RTUs)
The ATMEGA2561-16MU fits SCADA RTU designs where the MCU aggregates digital inputs, analog measurements, and field-bus telemetry into a single reporting node. Its 54 I/O lines handle DI/DO channels, its 8-channel 10-bit ADC reads 4-20 mA loops or 0-10 V process signals, and its four USARTs support RS-232/RS-485 multidrop polling plus a radio modem link. The 256 KB Flash plus 4 KB EEPROM support DNP3, IEC 60870-5-104, or Modbus firmware with local event-log buffering, and the industrial -40 C to +85 C range plus 5 V supply tolerance allow direct deployment in outdoor cabinets with proper isolation. JTAG and ISP simplify commissioning and field firmware updates.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA2561-16MU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA2561-16MUR | ATMEGA2561-16AU | ATMEGA2561-16AI | ATMEGA1281-16MU | ATMEGA1281-16MUR | ATMEGA1281-16AU |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VFQFN (9x9) | 64-VFQFN (9x9) - same | 64-TQFP - NOT same footprint | 64-TQFP - NOT same footprint | 64-VFQFN (9x9) - same | 64-VFQFN (9x9) - same | 64-TQFP - NOT same footprint |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 128 KB (-50%) | 128 KB (-50%) |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Maximum Frequency | 16 MHz (16 MIPS) | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| I/O Lines | 54 | 54 | 54 | 54 | 54 | 54 | 54 |
| Operating Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
Ключевые отличия
- Highest-density Flash in 64-VFQFN family (против ATMEGA1281-16MU)
- Pin-compatible 100% spec match (против ATMEGA2561-16MUR)
- Quad-USART bridge capability (против ATMEGA1281-16MU)
Заметки по проектированию
Estimated: at 16 MHz active and 5 V supply, the ATMEGA2561-16MU consumes approximately 15-20 mA active and 5-10 uA in power-down. Place a 100 nF ceramic decoupling capacitor within 5 mm of each VCC pin (five pins) plus a 10 uF bulk capacitor on the supply rail. For AVCC use an LC or ferrite-bead filter (10 ohm + 10 uF) to isolate the ADC supply from digital switching noise. Power-down mode retains SRAM/EEPROM contents for months on a coin-cell backup if needed.
The 64-VFQFN 9x9 mm package requires a center-thermal-pad land on the PCB with at least 8 thermal vias (0.3 mm drill, 1.0 mm pitch) connecting to a ground plane to achieve the 30 C/W theta-JA target. Keep high-current switching traces (relay drivers, motor drivers) away from ADC traces; route the ADC reference (AREF) capacitor within 10 mm of the pin and place a guard ring tied to AGND around sensitive analog signal traces. Exposed pad MUST be soldered to the PCB land for mechanical reliability and thermal performance.
Do not exceed 5.5 V on VCC - the ATmega2561 is not 3.3 V tolerant despite its AVR heritage. Do not connect JTAG pins (PF4-PF7/TDI/TMS/TCK/TDO) directly to external signals without considering that JTAG fuse programming can disable these as I/O. Brown-out detect should be enabled and tuned to 4.0 V or 2.7 V to prevent Flash corruption during supply transients. When migrating from ATmega1281 firmware, recompile with the ATmega2561 build profile in MCUdude MegaCore or AVR Studio to expose the larger Flash region - using the wrong linker script yields silently truncated firmware.
External memory interface (EBI/EMI) signals should be length-matched to within 5 mm if the bus runs above 8 MHz to avoid setup/hold violations; add 10-22 pF series damping resistors if ringing exceeds 0.5 Vpp. The JTAG TDO signal has a tri-state output and requires a pull-up of 10-47 kohm to avoid floating during scan chains. SPI signals should use a ground reference and series resistors if the cable length exceeds 50 mm, particularly when connecting to SD cards or radio modules.
Информация о соответствии
ATMEGA2561-16MU is RoHS compliant per Microchip product page and is supplied in lead-free packaging. It is not AEC-Q100 qualified for automotive applications; AEC-Q100 grade parts in this family use a different part suffix. Halogen-free status not explicitly stated in the verified web data.
