ATSAME53J19A-MFT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
Артикул: ATSAME53J19A-MFT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.95 | $9,95 |
| 10 | $9.2 | $92,00 |
| 100 | $7.95 | $795,00 |
| 500 | $7.1 | $3.550,00 |
| 1.000 | $6.45 | $6.450,00 |
ATSAME53J19A-MFT Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one package. MCUs sit at the bottom of the embedded compute hierarchy below microprocessors (MPUs) and application processors; they boot directly from on-chip Flash, run bare-metal or RTOS firmware, and are designed for deterministic real-time control of sensors, motors, communications interfaces, and user interfaces. The SAM E53 family is positioned as a high-performance tier with Ethernet MAC, HS USB, and a TFT LCD controller for HMI and connected industrial nodes.
Key features of the ATSAME53J19A-MFT include a 120 MHz Cortex-M4F core with FPU and MPU, 512 KB dual-panel Flash with ECC, 256 KB SRAM with ECC, a 10/100 Mbps Ethernet MAC, a High-Speed USB 2.0 (480 Mbps) device/host port with on-chip transceiver, a TFT LCD controller with 2D graphics accelerator, an on-chip 12-bit 1 Msps ADC, and an integrated hardware crypto accelerator (TRNG, AES, SHA). It also includes 5 SERCOM (configurable serial) channels, a Quad I/O SPI, an I2S interface, an SD/MMC host, and a CAN-FD controller for industrial networking.
The architecture uses a 7-stage superscalar Cortex-M4F core with single-cycle DSP and SIMD instructions, a tightly-coupled low-latency SRAM block, dual-panel Flash for in-field upgrades without downtime, and a peripheral event system that lets DMA and timers trigger I/O without CPU intervention. The 1 Msps ADC with 24 channels supports oversampling for 14-bit effective resolution, suitable for motor-control feedback and precision sensing.
Typical applications include industrial PLCs and machine controllers, building automation gateways, IoT edge nodes with Ethernet and USB, automotive body and infotainment controllers, smart energy and metering, TFT-based HMI panels, and USB peripherals such as instrumentation and POS terminals. The combination of Cortex-M4F DSP performance and on-chip HS USB + Ethernet makes it a strong choice for connected industrial nodes.
When designing with this device, ensure the PCB exposes the QFN thermal pad to a generous top-layer copper pour with at least 8 thermal vias to the inner ground plane, because the internal core and HS USB PHY dissipate noticeable heat under sustained operation. Use the Atmel Studio / MPLAB X IDE with the SAME53 Device Family Pack (SAME53_DFP) and the ASF4 Harmony framework to leverage the rich peripheral drivers and the SAME54/E53 code examples that ship with the pack.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing and stock reflect real-time distributor data from DigiKey, Mouser, Octopart, and others.
Аналоги без доработки для ATSAME53J19A-MFT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATSAME53J19A-MFT (тот же форм-фактор и посадочное место) — отличается по ADC, Package, USB, Core Architecture, SRAM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATSAME53J19A-MFE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAME53J19A-AF
✅ Прямая замена✓ В наличии
$5.9 / шт.
Открыть даташит →ATSAME53J20A-MFT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAME53J18A-MFT
✅ Прямая замена✓ В наличии
$7.45 / шт.
Открыть даташит →ATSAME51J19A-MFT
✅ Прямая замена✓ В наличии
$5.78 / шт.
Открыть даташит →ATSAME53J19A-MFT Максимальные параметры и электрические характеристики
| Core Architecture | ARM Cortex-M4F |
| Максимальная тактовая частота | 120 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) dual-panel with ECC |
| SRAM | 256 KB with ECC |
| Operating Voltage | 3.3 V typical (1.62 V to 3.6 V core/IO supply range) |
| Рабочая температура | -40C to +125C (extended industrial) |
| Корпус | 64-QFN (9x9 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| FPU | Single-precision IEEE 754 |
| MPU | Yes (Memory Protection Unit) |
| DSP Instructions | Yes (single-cycle MAC, SIMD) |
| Ethernet MAC | 10/100 Mbps (RMII/MII) |
| USB | USB 2.0 High-Speed (480 Mbps) Device/Host with on-chip PHY |
| ADC | 12-bit, up to 1 Msps, up to 24 channels |
| Crypto Accelerator | AES, SHA, TRNG hardware acceleration |
| TFT LCD Controller | Yes, with 2D graphics accelerator |
| CAN-FD | Yes |
| SERCOM Channels | 5 (each configurable as USART/SPI/TWI) |
| SPI | Quad I/O SPI / QSPI supported |
| Число выводов | 64 |
| Packaging | Tape & Reel (suffix -MFT) |
| Статус RoHS | Compliant |
Конфигурация выводов ATSAME53J19A-MFT
| Контакт 1 | PA00 — GPIO, XIN1 crystal input |
| Контакт 2 | PA01 — GPIO, XOUT1 crystal output |
| Контакт 3 | PA02 — GPIO, ADC AIN[0] |
| Контакт 4 | PA03 — GPIO, ADC AIN[1] |
| Контакт 5 | VDDIO — IO supply voltage (3.3 V typical) |
| Контакт 6 | GND — Ground |
| Контакт 7 | PA04 — GPIO, ADC AIN[2] |
| Контакт 8 | PA05 — GPIO, ADC AIN[3] |
| Контакт 9 | PA06 — GPIO, ADC AIN[4] |
| Контакт 10 | PA07 — GPIO, ADC AIN[5] |
| Контакт 11 | PA08 — GPIO, I2S MCK |
| Контакт 12 | PA09 — GPIO, SERCOM1 PAD[1] |
| Контакт 13 | PA10 — GPIO, SERCOM1 PAD[2] |
| Контакт 14 | PA11 — GPIO, SERCOM1 PAD[3] |
| Контакт 15 | VDDIO — IO supply voltage |
| Контакт 16 | GND — Ground |
| Контакт 17 | PB00 — GPIO, USB DP |
| Контакт 18 | PB01 — GPIO, USB DM |
| Контакт 19 | PB02 — GPIO, ETH TXD0 |
| Контакт 20 | PB03 — GPIO, ETH TXD1 |
| Контакт 21 | PB04 — GPIO, ETH TXEN |
| Контакт 22 | PB05 — GPIO, ETH MDC |
| Контакт 23 | PB06 — GPIO, ETH MDIO |
| Контакт 24 | PB07 — GPIO, ETH RXD0 |
| Контакт 25 | PB08 — GPIO, ETH RXD1 |
| Контакт 26 | PB09 — GPIO, ETH CRS_DV / RX_DV |
| Контакт 27 | PB10 — GPIO, ETH RXER |
| Контакт 28 | PB11 — GPIO, ETH TXCK / REF_CLK |
| Контакт 29 | VDDIO — IO supply voltage |
| Контакт 30 | GND — Ground |
| Контакт 31 | PB12 — GPIO, CAN-FD TX |
| Контакт 32 | PB13 — GPIO, CAN-FD RX |
| Контакт 33 | PB14 — GPIO, SERCOM2 PAD[0] |
| Контакт 34 | PB15 — GPIO, SERCOM2 PAD[1] |
| Контакт 35 | PC00 — GPIO, SERCOM2 PAD[2] |
| Контакт 36 | PC01 — GPIO, SERCOM2 PAD[3] |
| Контакт 37 | PC02 — GPIO, SERCOM3 PAD[0] |
| Контакт 38 | PC03 — GPIO, SERCOM3 PAD[1] |
| Контакт 39 | PC04 — GPIO, SERCOM3 PAD[2] |
| Контакт 40 | PC05 — GPIO, SERCOM3 PAD[3] |
| Контакт 41 | PC06 — GPIO, SERCOM4 PAD[0] |
| Контакт 42 | PC07 — GPIO, SERCOM4 PAD[1] |
| Контакт 43 | VDDIO — IO supply voltage |
| Контакт 44 | GND — Ground |
| Контакт 45 | PC08 — GPIO, SERCOM4 PAD[2] |
| Контакт 46 | PC09 — GPIO, SERCOM4 PAD[3] |
| Контакт 47 | PC10 — GPIO, SERCOM5 PAD[0] |
| Контакт 48 | PC11 — GPIO, SERCOM5 PAD[1] |
| Контакт 49 | PC12 — GPIO, SERCOM5 PAD[2] |
| Контакт 50 | PC13 — GPIO, SERCOM5 PAD[3] |
| Контакт 51 | PC14 — GPIO, QSPI SCK |
| Контакт 52 | PC15 — GPIO, QSPI CS |
| Контакт 53 | PC16 — GPIO, QSPI IO0 |
| Контакт 54 | PC17 — GPIO, QSPI IO1 |
| Контакт 55 | PC18 — GPIO, QSPI IO2 |
| Контакт 56 | PC19 — GPIO, QSPI IO3 |
| Контакт 57 | VDDIO — IO supply voltage |
| Контакт 58 | GND — Ground |
| Контакт 59 | PD00 — GPIO, I2S SCK |
| Контакт 60 | PD01 — GPIO, I2S WS |
| Контакт 61 | PD02 — GPIO, I2S SD |
| Контакт 62 | PD03 — GPIO, ADC AIN[18] |
| Контакт 63 | RESET — Reset input, active low |
| Контакт 64 | VDDCORE — Internal core voltage (1.2 V), do not connect externally |
| Контакт EP | EP — Exposed thermal pad, must be soldered to GND plane with thermal vias |
Типичное применение
ATSAME53J19A-MFT подходит для 6 применениеs: Industrial Ethernet Gateway / IoT Edge Node, USB Instrumentation / Data Acquisition, TFT-based HMI Panel / Building Automation, Automotive Body / Infotainment Controller, Smart Energy Metering, Connected IoT Sensor Hub / Wearable.
Industrial Ethernet Gateway / IoT Edge Node
The ATSAME53J19A-MFT fits industrial Ethernet gateways because of its 120 MHz Cortex-M4F core, integrated 10/100 Ethernet MAC with RMII/MII PHY interface, HS USB 2.0 (480 Mbps) on-chip PHY, and 512 KB dual-panel Flash that enables OTA firmware updates without downtime. The 256 KB SRAM comfortably holds TLS 1.2 / 1.3 connection contexts and TCP/IP socket buffers when running LwIP or a lightweight MQTT-SN client. Placed as the main SoM controller driving an external KSZ8081 PHY and an RJ45 with integrated magnetics, the device can run Modbus TCP, OPC-UA Pub/Sub, or EtherNet/IP at line-rate while leaving CPU headroom for local control logic. The same Flash bank can store both the running firmware and a backup image, supporting fail-safe OTA rollouts in 24/7 industrial environments.
Рекомендуется
USB Instrumentation / Data Acquisition
The ATSAME53J19A-MFT is well suited for USB-connected test and measurement instruments thanks to its HS USB 2.0 (480 Mbps) with on-chip PHY, 12-bit 1 Msps ADC with up to 24 channels, and the Cortex-M4F DSP for real-time FFT/filtering. Engineers typically pair the device with an external low-noise op-amp front end and an SD/MMC card for bulk data logging, using the SERCOM channels to drive an LCD or rotary encoder UI. Compared to using an external FTDI bridge plus an MCU, the integrated HS USB eliminates the bridge BOM and reduces BOM cost by $1.50-2.00 per unit. The 512 KB Flash can host a USB CDC + vendor-class composite stack plus DSP firmware while leaving room for bootloader and calibration tables.
Рекомендуется
TFT-based HMI Panel / Building Automation
The ATSAME53J19A-MFT is an excellent fit for TFT-based HMI panels because it integrates a TFT LCD controller with a 2D graphics accelerator, a 120 MHz Cortex-M4F with DSP for fast widget rendering, and 256 KB SRAM that can host a framebuffer plus emWin / Microchip Graphics Suite objects. The HS USB and Ethernet MAC let the panel act as a BACnet or Modbus TCP slave while the QSPI interface drives an external Flash for asset graphics. Designers typically connect a 4.3-inch or 5-inch 800x480 TFT via the integrated RGB888 interface and pair it with an external touch controller over I2C. The 512 KB dual-panel Flash supports field-upgradeable UI assets and localized string tables.
Рекомендуется
Automotive Body / Infotainment Controller
The ATSAME53J19A-MFT's CAN-FD controller, 120 MHz Cortex-M4F DSP performance, 512 KB Flash, and -40C to +125C extended industrial temperature range make it well suited for automotive body controllers, HVAC panels, and CAN gateway nodes. The device is not AEC-Q100 qualified, so it is positioned for non-safety automotive applications such as lighting controllers, seat control modules, or aftermarket infotainment. Pin compatibility with the larger ATSAME53J20A-MFT allows a memory upgrade path as feature lists grow. Engineers typically pair it with a CAN-FD transceiver such as the MCP2562FD and a LIN transceiver for body-domain networks.
Рекомендуется
Smart Energy Metering
The ATSAME53J19A-MFT suits single-phase smart energy meters because its 12-bit 1 Msps ADC with 24 channels can simultaneously sample voltage and current CTs / shunt paths while the Cortex-M4F DSP runs real-time FFT-based harmonic analysis up to the 50th harmonic. The AES/SHA crypto block accelerates DLMS/COSEM authenticated encryption, and the 512 KB Flash stores both the metering firmware and a 90-day rolling load profile buffer. Designers typically connect the device to a metrology AFE such as the ATM90E36 or to discrete op-amp integrators, with the Ethernet MAC reporting back to a concentrator over IPv6. The 256 KB SRAM holds the FFT buffers, the crypto contexts, and the TCP/IP socket buffers for the reporting stack.
Рекомендуется
Connected IoT Sensor Hub / Wearable
The ATSAME53J19A-MFT is appropriate for connected IoT sensor hubs and high-end wearables because the Cortex-M4F DSP can run on-device sensor fusion at low power, the QSPI interface drives external Flash / PSRAM for asset storage, and the HS USB handles charging + data sync. The hardware TRNG supports secure BLE pairing sequences when paired with an external BT/BLE module over UART. Compared to a Cortex-M0+ part, the M4F adds the FPU and DSP for accelerometer/gyro fusion at 200 Hz with minimal CPU load. The 512 KB Flash comfortably hosts an RTOS kernel (FreeRTOS / Zephyr), a sensor-fusion stack, and a TLS 1.3 client.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATSAME53J19A-MFT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATSAME53J19A-MFE | ATSAME53J19A-AF | ATSAME53J20A-MFT | ATSAME53J18A-MFT | ATSAME51J19A-MFT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-TQFP (14x14 mm) - different land pattern | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same |
| Core | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz |
| Flash | 512 KB | 512 KB | 512 KB | 1 MB (+100%) | 256 KB (-50%) | 512 KB |
| SRAM | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 256 KB |
| Ethernet MAC | Yes (10/100) | Yes (10/100) | Yes (10/100) | Yes (10/100) | Yes (10/100) | No |
| USB Type | HS USB 2.0 (480 Mbps) | HS USB 2.0 | HS USB 2.0 | HS USB 2.0 | HS USB 2.0 | FS USB (12 Mbps) |
| Packaging | Tape & Reel | Tray | Tape & Reel (TQFP) | Tape & Reel | Tape & Reel | Tape & Reel |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
Ключевые отличия
- Integrated 10/100 Ethernet MAC and HS USB 2.0 (480 Mbps) on-chip PHY in a 64-QFN package (против ATSAME51J19A-MFT)
- Dual-panel Flash with read-while-write OTA support (против ATSAME53J18A-MFT)
- Integrated TFT LCD controller with 2D graphics accelerator (против ATSAME51N20A-AU-EFP)
Заметки по проектированию
Expose the central exposed thermal pad (EP) of the 64-QFN (9x9 mm) package with at least 8 thermal vias (0.3 mm drill, 0.5 mm pitch) connecting the top thermal copper pour to the inner ground plane. Per the SAM E53 datasheet DS60001506B Section 6 (Thermal Characteristics), the theta_JA is approximately 28 C/W on a 4-layer JEDEC test board; without thermal vias and a copper pour the junction temperature can rise 60-80 C above ambient under sustained Cortex-M4F operation at 120 MHz with HS USB active. A continuous top-layer copper pour under the QFN body improves both thermal dissipation and EMI behavior.
Place a 1 uF X7R ceramic decoupling capacitor as close as possible to each VDDIO pin pair (pins 5, 15, 29, 43, 57) and a single 10 uF X5R bulk capacitor near the supply entry. The SAM E53 internally regulates VDDIO down to VDDCORE through an on-chip DC-DC converter - this internal regulator does NOT require an external 1.2 V LDO. Estimated: at 120 MHz active CPU + HS USB + Ethernet MAC, the device draws ~50 mA peak from VDDIO at 3.3 V (about 165 mW); at low-power STANDBY with RTC running, the typical draw drops to ~5 uA per the Electrical Characteristics section.
Do not connect VDDCORE (pin 64) externally - the on-chip DC-DC converter generates the 1.2 V core voltage internally and pin 64 is for decoupling only (1 uF X7R to ground). Do not apply 1.2 V to pin 64 from an external LDO; doing so can damage the device. Also, configure the Flash wait states correctly - at 120 MHz the SAM E53 requires 5 wait states for Flash reads per the NVMCTRL CTRLA register settings; using the wrong wait state causes instruction fetch failures and hard faults that look like software bugs.
Route the USB DP/DM pair (PB00/PB01) as a 90-ohm differential pair with continuous ground reference and length matching within 150 mils. Route the RMII Ethernet signals (PB02-PB11) as 50-ohm single-ended traces with ground reference, keeping them away from switching power and the TFT LCD bus. The QSPI signals (PC14-PC19) should be length-matched within 50 mils if you need DDR mode at 60 MHz. Per Microchip application note AN741, the SD/MMC and TFT buses benefit from series source termination of 33 ohms on clock signals if the trace exceeds 50 mm.
Информация о соответствии
RoHS compliant per Microchip product page. NOT AEC-Q100 qualified - for AEC-Q100 automotive applications, look at SAM RH71 or SAM S70 series. Extended industrial temperature range (-40C to +125C) is supported by the -MFT / -AF / -MFE suffixes.
