DG412DY+ - 4-Channel SPST Analog Switch | Analog Devices
Артикул: DG412DY+ ✓ АктивенDG412DY+ Обзор
An analog switch is a semiconductor device that uses digital control signals to connect or disconnect analog paths. The DG412 family belongs to the analog-switch and multiplexer hierarchy, where an analog switch provides one selectable path, a multiplexer combines multiple paths, and a demultiplexer distributes one path among multiple destinations. CMOS implementations are widely used because they can combine low control-input current, broad signal-voltage handling, and compact integration.
The DG412DY+ uses improved low-on-resistance matching between switches, with a maximum matching difference of 3 ohm, and guaranteed on-resistance flatness across the signal range, with a maximum variation of 4 ohm. These characteristics reduce channel-to-channel gain and resistance errors when several switched paths feed precision measurement, test, signal-routing, or data-acquisition circuits. Break-before-make behavior prevents the two sides of a switch from being connected simultaneously during transition.
The device supports TTL-compatible control logic and single-supply operation. Its four SPST channels can be used independently to select test paths, route sensor outputs, disconnect external loads, or implement sample-and-hold isolation stages. The low-resistance matching and controlled switching behavior make it especially useful where adding resistance-induced error or inconsistent channel loading would degrade system accuracy.
When laying out the DG412DY+, place input and output traces away from fast digital control and clock nets to minimize capacitive coupling. Keep the analog paths short, use a continuous ground plane, and decouple the supply close to the device. Confirm that every switched signal remains inside the operating voltage range and that break-before-make timing satisfies the source and load requirements.
This page combines the manufacturer product information, distributor identifiers, pin-compatible comparison data, application guidance, and practical PCB considerations. It is intended to help engineers identify whether the DG412DY+ fits a routing design, how it compares with other switch families, and which constraints must be checked before PCB release.
Аналоги без доработки для DG412DY+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DG412DY+ (тот же форм-фактор и посадочное место) — отличается по Switch Configuration, Package, On-Resistance.
ADG412
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG412DY
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG412DY
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG412DY+ Максимальные параметры и электрические характеристики
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| On-Resistance | 45 ohm |
| On-Resistance Matching Between Switches | 3 ohm maximum |
| On-Resistance Flatness Over Signal Range | 4 ohm maximum variation |
| Signal Conduction | Bidirectional |
| Switching Action | Break-before-make |
| Control Logic Compatibility | TTL-compatible |
| Supply Capability | Single-supply operation |
| Корпус | 16-pin SOIC |
| Тип монтажа | Surface mount |
| Диапазон рабочих температур | -40 °C to +85 °C |
| Analog Signal Maximum | +30 V |
| Analog Signal Minimum | 10 V |
| Production Status | Production |
Руководство по цоколевке DG412DY+ в корпусе 16-pin soic
Цоколевка для DG412DY+ (корпус 16-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для DG412DY+.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DG412DY+ подходит для 6 применениеs: Precision Test-Signal Routing, Data-Acquisition Channel Isolation, Sensor Signal Multiplexing, Sample-and-Hold Front Ends, Automated Measurement Systems, External Load Disconnect Circuitry.
Precision Test-Signal Routing
The DG412DY+ fits four-channel precision test-signal routing because each SPST path can connect a test point, source, or load independently. Its 3 ohm maximum matching between switches helps limit channel-to-channel resistance differences, while 4 ohm maximum flatness variation reduces signal-dependent errors across the operating range. The 45 ohm on-resistance must be included in the complete impedance budget, especially for high-impedance sensors and low-amplitude measurements.
Рекомендуется
Data-Acquisition Channel Isolation
The DG412DY+ can isolate or reconnect individual data-acquisition inputs without introducing the substantial leakage associated with many mechanical relays. Four independent bidirectional SPST circuits provide flexible channel management, and break-before-make operation prevents direct contention during switching. The analog designer should account for the 45 ohm series resistance, control-input capacitance, and signal-dependent flatness when setting acquisition gain and settling requirements.
Рекомендуется
Sensor Signal Multiplexing
The DG412DY+ is suitable for routing outputs from multiple sensors into a shared amplifier or measurement channel when low resistance variation between switches is important. Bidirectional conduction accommodates source or drain configurations, while 3 ohm maximum on-resistance matching improves consistency among selected channels. The circuit must tolerate the added 45 ohm path resistance and should use short, guarded analog traces to minimize pickup and switching transients.
Рекомендуется
Sample-and-Hold Front Ends
In sample-and-hold front ends, the DG412DY+ can connect a sampled node to a high-impedance holding network and then isolate it for subsequent conversion. Break-before-make switching limits overlap between the sampled and isolated states, while four channels permit repeated sampling, hold, reset, and signal-selection arrangements. Care must be taken because the switch contributes 45 ohm on-resistance and finite switching time, both of which affect acquisition settling and sample-rate design.
Рекомендуется
Automated Measurement Systems
The DG412DY+ can provide programmable connectivity in automated measurement systems requiring four independent analog paths. Its TTL-compatible controls simplify coordination with test equipment, and the compact 16-pin SOIC package supports dense instrumentation designs. Matching and flatness specifications help avoid one switch path behaving materially differently from another, but the 45 ohm resistance must be calibrated into precision measurements where required.
Рекомендуется
External Load Disconnect Circuitry
The DG412DY+ can disconnect external loads, test fixtures, or sensitive subcircuits while preserving a common signal path. Four independent channels allow separate functions such as load isolation, fixture selection, and signal inhibition, with bidirectional conduction supporting conventional signal flow. Designers should verify the maximum analog-signal rating, control thresholds, switch capacitance, and off-state behavior before applying the device outside the manufacturer-specified operating conditions.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DG412DY+ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADG412 | DG412DY | DG412DY |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Renesas Electronics | Vishay Intertechnology |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Number of Circuits | 4 circuits | 4 SPST switches | 4 circuits | 4 SPST switches |
| Switch Configuration | 1:1 SPST | 1:1 SPST | 1:1 | 1:1 |
Ключевые отличия
- Improved channel-to-channel resistance matching (против Renesas DG412DY)
- Documented signal-range resistance flatness (против Vishay DG412DY)
- Analog Devices and Maxim Integrated sourcing path (против ADG412)
Заметки по проектированию
Route switched analog signals as short, direct traces on a continuous ground plane. Keep the DG412DY+ near the connector, sensor, or measurement node that it controls, and avoid running sensitive nodes beneath the digital control inputs. Place the supply bypass capacitor close to the device supply terminal, and ground the returned switching current through the shortest available path to minimize ground bounce and analog coupling.
Include the nominal 45 ohm on-resistance in the signal-path calculation, then verify settling against the control transition using the manufacturer's switching-time and capacitance information. The 3 ohm maximum matching and 4 ohm maximum flatness specifications help quantify differences between paths, but they do not remove the need to check source impedance, load capacitance, and available settling time. Use a high-impedance receiving stage when the added resistance cannot be tolerated.
Do not treat every DG412DY marking as an interchangeable source of the DG412DY+. The same shortened order code is associated with Analog Devices or Maxim Integrated, Renesas Electronics, and Vishay Intertechnology products. Before substitution, verify the manufacturer, exact suffix, 16-pin SOIC footprint, control polarity, supply limits, signal rating, on-resistance, and switching timing against the approved component specification.
Provide local supply decoupling and route the return current directly to the system ground plane. The DG412DY+ is a CMOS interface device rather than a high-power regulator, but its control transitions can disturb analog nodes through supply and ground impedance. Keep high-current return paths away from sensitive switched traces, and verify that supply-current limits remain valid for all four channels and every combination of control states.
Информация о соответствии
Compliance declarations are not stated in the product and distributor records. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact manufacturer and ordering code before release.