MAX232AESE+ - Dual RS-232 Transceiver in SOIC-16 | Maxim
Артикул: MAX232AESE+ ✓ АктивенMAX232AESE+ Обзор
An RS-232 transceiver is an interface IC that combines line drivers and receivers for bidirectional serial communication. The MAX220 through MAX249 family is designed for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly systems in which approximately ±12 V is unavailable. The MAX232AESE+ implements this interface function with a single +5 V supply while providing separate transmit and receive channels.
The device includes two RS-232 drivers and two receivers, giving the system two driver channels and two receiver channels in one package. Its specified 4.5 V to 5.5 V operating-supply range supports regulated 5 V system rails. A 16-SOIC package allows use of familiar PCB routing and assembly practices, while its 3.90 mm package width fits standard narrow-body SOIC board layouts.
The MAX232A family is part of Maxim Integrated's +5 V-powered multichannel RS-232 portfolio. A single IC can support two transmit paths and two receive paths, reducing the number of separate interface components required in multi-channel equipment. The product description identifies the MAX232A device family as production and associates the MAX232A with +5 V-powered multichannel RS-232 drivers and receivers.
Typical uses include service-console connections, configuration interfaces, industrial-control links, test equipment, and embedded systems that require a wired RS-232 port. In these applications, the two transmitter channels can carry command or data signals, while the two receiver channels can accept responses or status information. The same IC can also be used where only one direction of communication is required, leaving additional channels available for future expansion or control signals.
When laying out a board around the MAX232AESE+, place charge-pump support capacitors and interface-network components close to their associated pins, and keep the RS-232 connector-side traces away from sensitive analog and digital timing circuitry. Confirm the external capacitor values, line-driver load assumptions, and protection requirements against the manufacturer datasheet before releasing the PCB layout.
This page combines the manufacturer product information, distributor package and availability details, cross-reference findings, a parameter comparison, and practical interface-design guidance. It is intended to accelerate component identification and replacement planning while preserving the distinction between a verified pin-compatible substitute and a merely functional alternative.
Аналоги без доработки для MAX232AESE+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX232AESE+ (тот же форм-фактор и посадочное место) — отличается по Product Type, Interface Standard, Package, Maximum Data Rate, Transceiver Configuration.
MAX232ESE+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX232CSE+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX232EESE+
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX232AEWE
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX232AESE+T
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX232AESE+ Характеристики
| Product Type | RS-232 dual transceiver |
| Driver Count | 2 drivers |
| Receiver Count | 2 receivers |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply | +5 V |
| Interface Standard | EIA/TIA-232E, V.28, V.24 |
| Transceiver Configuration | 2/2 full-duplex RS-232 |
| Technology | Enhanced CMOS |
| Корпус | 16-SOIC |
| Package Width | 3.90 mm |
| Число выводов | 16 pins |
| Тип монтажа | Surface mount |
Руководство по цоколевке MAX232AESE+ в корпусе 3.90 mm
Цоколевка для MAX232AESE+ (корпус 3.90 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX232AESE+.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX232AESE+ подходит для 6 применениеs: Industrial Controller Service Port, Test and Measurement Console, Data Acquisition and Control Module, Embedded Equipment Maintenance Interface, Networking Equipment Management Port, Automated Test Equipment Interface.
Industrial Controller Service Port
The MAX232AESE+ fits an industrial controller that exposes configuration, diagnostics, or service commands through a wired RS-232 connector. Its two drivers and two receivers permit two outbound command paths and two inbound status paths from one +5 V interface IC, reducing the number of discrete interface components. Operating from 4.5 V to 5.5 V supports a regulated 5 V control rail. The main design consideration is isolating connector-side transients with the protection strategy required by the installation environment, while routing the sensitive transceiver circuitry away from switching nodes and high-current machinery wiring.
Рекомендуется
Test and Measurement Console
A bench instrument can use the MAX232AESE+ to bridge its host computer and front-panel service circuitry through RS-232. The two transmit channels can carry separate commands or status data, while the two receive channels can accept instrument responses or remote-control feedback. Because the device operates from 4.5 V to 5.5 V, it aligns with conventional +5 V logic without requiring a separate approximately ±12 V supply. Keep the receiver traces short, terminate them according to the system grounding policy, and use the manufacturer application circuit to select the required charge-pump and interface capacitors.
Рекомендуется
Data Acquisition and Control Module
The MAX232AESE+ is useful in a data-acquisition module that transfers measurement commands and collected results over an RS-232 link. Two driver channels and two receiver channels provide flexibility for separating control traffic from status or alarm traffic. Its +5 V operating range allows implementation beside CMOS control logic, while the compact 16-SOIC package helps preserve board area. For reliable operation, confirm that the selected module regulator can tolerate the transceiver's supply current transients and that the external connector protection is consistent with the cable length and grounding environment.
Рекомендуется
Embedded Equipment Maintenance Interface
Embedded equipment can retain a maintenance connector implemented with the MAX232AESE+ even when the primary system interface is modern and high speed. The RS-232 channels provide a simple path for boot-loader access, factory testing, firmware recovery, and diagnostic commands. Two transmitters and two receivers allow separate service and status channels if required. The device's 4.5 V to 5.5 V supply range is compatible with regulated 5 V equipment, but production designs should validate the selected grade's temperature range, enforce a controlled ground reference, and add connector-level surge protection where cables leave the enclosure.
Рекомендуется
Networking Equipment Management Port
The MAX232AESE+ can implement an out-of-band management connection in switches, routers, or other networked equipment where a dedicated RS-232 console remains useful for installation and recovery. One transmit channel can carry console commands and one receive channel can return equipment status, while the second pair handles auxiliary control signals. The +5 V architecture simplifies integration with equipment already using 5 V logic rails. Design the console interface with a defined signal-ground relationship, protection appropriate to exposed cabling, and firmware flow control so long messages cannot overrun the receive buffer.
Рекомендуется
Automated Test Equipment Interface
Automated test equipment can use the MAX232AESE+ as a local controller link between test electronics, fixtures, and supervisory software. Two transmitter channels support separate test commands and fixture-control signals, while two receiver channels can return measurements and equipment acknowledgments. The 4.5 V to 5.5 V range permits use with a regulated 5 V test-board rail, and the 16-SOIC footprint simplifies assembly where space is limited. Account for grounding differences between the tester and fixture, place protection close to the connector, and validate command timing against the slowest supported endpoint.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX232AESE+ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX232ESE+ | MAX232CSE+ | MAX232EESE+ | MAX232AEWE | MAX232AESE+T |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Nominal Supply | +5 V | +5 V family candidate | +5 V family candidate | +5 V family candidate | +5 V family candidate | +5 V family candidate |
| Package Width | 3.90 mm | 3.90 mm SOIC-16 family candidate | 3.90 mm SOIC-16 family candidate | 3.90 mm SOIC-16 family candidate | 3.90 mm SOIC-16 family candidate | 3.90 mm SOIC-16 family candidate |
Ключевые отличия
- Combines two transmit and two receive channels in one interface IC (против MAX232ESE+)
- Uses a compact standard narrow-body SOIC-16 footprint (против MAX232CSE+)
- Operates directly from a regulated 5 V rail (против MAX232EESE+)
- Supports the documented EIA/TIA-232E, V.28 and V.24 interface family (против MAX232AEWE)
Заметки по проектированию
Place the charge-pump support capacitors and the RS-232 interface-network components close to their corresponding MAX232AESE+ pins. Keep the 16-SOIC footprint consistent with the manufacturer package drawing and confirm that connector-side protection is positioned near the external connector. Use the datasheet's reference circuit to determine capacitor values and avoid substituting values from a different MAX232-family member without checking the charge-pump design.
Do not treat every MAX232-family ordering code as automatically interchangeable. Although the listed candidates use the same broad 16-SOIC interface arrangement, external capacitor values, slew rate, temperature grade, and active or shutdown behavior can differ between suffixes. Before releasing a substitution, compare the manufacturer pin tables and electrical characteristics and verify that the PCB accommodates the selected package's land pattern.
Route RS-232 connector traces away from clocks, switching regulators, and sensitive analog inputs to reduce susceptibility to common-mode noise. Maintain a deliberate signal-ground relationship between the transceiver and connector shield, especially when the connected equipment uses a different earth reference. Where a cable leaves the enclosure, place the protection network near the connector and use the manufacturer's application guidance to select protection and bypass components.
The MAX232AESE+ is intended for a 4.5 V to 5.5 V supply, so the system regulator and local bypass network must remain within that range under load and transient conditions. Confirm the device's supply-current requirement from the manufacturer datasheet and allow adequate regulator headroom. Check the recommended input and charge-pump capacitor values against the selected family member rather than relying on general RS-232 design conventions.
Информация о соответствии
The product is an RS-232 interface IC rather than an automotive-qualified device, so AEC-Q100 is not applicable. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established by the manufacturer text available for this part.