DSPIC33EP32MC502-H/MM - 70MIPS 16-bit DSC AEC-Q100 | Microchip
Артикул: DSPIC33EP32MC502-H/MM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
DSPIC33EP32MC502-H/MM Обзор
A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP, providing a Harvard-architecture 16-bit core with DSP multiply-accumulate instructions. DSCs are the control backbone of digital power conversion and precision motor-drive systems where deterministic closed-loop control at tens to hundreds of kilohertz is required.
Key features include the 70 MIPS dsPIC DSC core with integrated DSP engine, high-speed PWM peripherals purpose-built for motor control, and advanced analog integration (comparators and 10/12-bit ADC). The 32KB self-programming flash and 4KB RAM suit compact field-oriented-control (FOC) firmware for PMSM, BLDC, and ACIM motors. AEC-Q100 qualification at up to 150C ambient supports underhood and onboard-charger placements.
Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with a 17-bit by 17-bit hardware multiplier and 40-bit accumulator, enabling single-cycle MAC operations. The high-speed PWM module supports complementary outputs, dead-time insertion, and fault protection essential for inverter bridges. Per the Microchip family datasheet (document DS70000657J), the family adds on-chip op amps on some variants and a rich communication set including UART, SPI, and I2C.
Typical applications include brushless DC and permanent-magnet motor control, digital switched-mode power supplies and power factor correction, and automotive auxiliary drives such as pumps and fans.
Design consideration: budget the exposed thermal pad copper area carefully at 150C automotive ambients, and use MPLAB X with the MPLAB Snap or ICD debugger, which the dsPIC33EP family fully supports for programming and debugging.
This page synthesizes distributor stock data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для DSPIC33EP32MC502-H/MM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP32MC502-H/MM (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, Operating Temperature, SRAM, Qualification.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP32MC502-I/MM
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33EP32MC502-E/MM
✅ Прямая замена✓ В наличии
$2.98 / шт.
Открыть даташит →DSPIC33EP32GP502T-E/MM
✅ Прямая замена✓ В наличии
$2.98 / шт.
Открыть даташит →DSPIC33EP32MC203T-I/TL
✅ Прямая замена✓ В наличии
$1.65 / шт.
Открыть даташит →DSPIC33EP32MC502-H/MM Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC DSC with DSP engine |
| Maximum CPU Speed | 70 MIPS |
| Flash Program Memory | 32 KB |
| RAM | 4 KB |
| Напряжение питания | 3.0 V to 3.6 V |
| Корпус | 28-VQFN Exposed Pad (MM) |
| Диапазон рабочих температур | -40C to +150C (H temperature grade) |
| Qualification | AEC-Q100, Automotive |
| Series | dsPIC 33EP (dsPIC33EP32MC50x) |
| Тип монтажа | Surface Mount |
| Количество выводов | 28 |
| Timers / High-Speed PWM | High-Speed PWM for motor control (per family datasheet) |
| Communication Interfaces | UART, SPI, I2C (per family datasheet) |
| Debug / Programming | MPLAB X IDE with MPLAB Snap / ICD (ICSP) |
| Статус RoHS | ROHS3 Compliant |
| Application Domain | Precision motor control, digital power conversion |
Руководство по цоколевке DSPIC33EP32MC502-H/MM в корпусе 28-vqfn exposed pad (mm)
Цоколевка для DSPIC33EP32MC502-H/MM (корпус 28-vqfn exposed pad (mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для DSPIC33EP32MC502-H/MM.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DSPIC33EP32MC502-H/MM подходит для 6 применениеs: BLDC / PMSM Motor Control, Digital Power Conversion (SMPS / PFC), Automotive Pumps, Fans and Actuators, Industrial Drives and Automation, Embedded Sensing and Signal Processing Nodes, Battery-Powered Portable Equipment.
BLDC / PMSM Motor Control
The DSPIC33EP32MC502-H/MM fits brushless DC and permanent-magnet synchronous motor drives because its 70 MIPS dsPIC DSC core executes field-oriented-control loops with single-cycle 17x17 multiply-accumulate operations, while the dedicated high-speed PWM module supplies complementary outputs with hardware dead-time insertion and fault shutdown. A typical sensorless FOC implementation runs the current loop at 20-50 kHz using the on-chip ADC and comparators, leaving CPU headroom for speed observers and communication. Placed at the heart of the inverter, the DSC reads phase currents through the ADC, computes dq-axis control in DSP-fixed-point math, and drives the gate bridge via the PWM outputs - replacing discrete DSP-plus-MCU solutions with one AEC-Q100 qualified 3.3V controller.
Рекомендуется
Digital Power Conversion (SMPS / PFC)
Digital switch-mode power supplies and power-factor-correction stages benefit from the DSPIC33EP32MC502-H/MM's deterministic 70 MIPS loop timing and high-speed PWM resolution, which support voltage- and current-mode control at switching frequencies well into the hundreds of kilohertz range with programmable dead time. The on-chip ADC samples output voltage and inductor current synchronously with the PWM period, and the DSP MAC instructions implement compensator difference equations without floating-point cost. Because the device is AEC-Q100 qualified to 150C, it also suits automotive onboard chargers and DC-DC bricks located near hot power stages. Firmware-based control additionally enables soft-start, burst mode, and adaptive dead-time features that analog controllers implement in external circuitry.
Рекомендуется
Automotive Pumps, Fans and Actuators
Electric coolant pumps, radiator fans, and actuators are classic dsPIC33EP32MC502 applications: the H temperature grade sustains 150C ambient, matching underhood thermal envelopes, while AEC-Q100 qualification satisfies automotive quality flows. The 70 MIPS core runs sensorless BLDC algorithms with sliding-mode or back-EMF observers, and the high-speed PWM module provides the fault protection needed when driving inverter bridges in safety-relevant fluid systems. The 28-pin VQFN exposed pad gives a compact footprint for mechatronic modules integrated directly on the pump housing. The device also offers UART, SPI, and I2C links for LIN-bridge or body-controller communication, letting a single DSC close the motor loop and report diagnostics.
Рекомендуется
Industrial Drives and Automation
In factory automation, the DSPIC33EP32MC502-H/MM serves compact servo, conveyor, and robotic-joint drives where its 70 MIPS DSP throughput and hardware MAC accelerate sensorless position estimation and torque-loop execution. The high-speed PWM peripheral integrates directly with external gate drivers, and communication peripherals (UART, SPI, I2C) connect to encoders, fieldbus bridges, or host PLCs. With 32KB flash, complete FOC firmware including startup sequencing, protection state machines, and parameter storage fits on-chip without external memory. The 28-VQFN exposed pad simplifies thermal design inside sealed drive enclosures, and the industrial/extended-temperature family variants (I/MM, E/MM) give purchasing second sources on the identical footprint for long-term supply resilience.
Рекомендуется
Embedded Sensing and Signal Processing Nodes
The DSP engine makes the DSPIC33EP32MC502-H/MM effective in sensor-processing nodes: FFT-based vibration analysis, RMS metering, and adaptive filtering all map naturally onto its 40-bit accumulator and single-cycle MAC. The analog front end - ADC inputs AN0-AN5, comparators, and reference support - accepts conditioned sensor signals directly, while SPI and I2C connect external precision converters or digital sensors. Processing 32KB of program space is sufficient for data-acquisition plus DSP math and a UART host protocol. At 3.0-3.6V operation, the device pairs cleanly with 3.3V sensor and transceiver ICs, and the small 28-pin VQFN suits dense distributed-sensing PCBs inside industrial and automotive monitoring equipment.
Рекомендуется
Battery-Powered Portable Equipment
Cordless power tools, portable pumps, and battery-managed hand equipment use the DSPIC33EP32MC502-H/MM to run the motor-control loop and battery supervision in one 3.3V DSC. The 70 MIPS core closes current loops fast enough for high-pole-count compact motors, and sleep/idle modes of the dsPIC33EP family reduce standby drain between operations. The compact 28-VQFN exposed pad fits the tight PCBs of handheld products, while the 32KB flash holds motor firmware plus protection and fuel-gauge routines. Because the family spans multiple temperature grades on identical silicon, consumer (85C) and extended-duty variants can share one PCB layout, simplifying product-line thermal and supply qualification.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP32MC502-H/MM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP32MC502-I/MM | DSPIC33EP32MC502-E/MM | DSPIC33EP32GP502T-E/MM | DSPIC33EP32MC203T-I/TL |
|---|---|---|---|---|---|
| Package | 28-VQFN Exposed Pad (MM) | 28-VQFN Exposed Pad (MM) - same | 28-VQFN Exposed Pad (MM) - same | 28-VQFN Exposed Pad (MM) - same | 28-VQFN (TL) - same pin-count family |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 20 KB |
| Max Ambient Temperature | 150C (H grade) | 85C (I grade) | Extended (E grade) | Extended (E grade) | 85C (I grade) |
| Peripheral Emphasis | Motor-control high-speed PWM | Motor-control high-speed PWM | Motor-control high-speed PWM | General-purpose peripherals | Motor-control high-speed PWM |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
Ключевые отличия
- Automotive 150C ambient rating (против DSPIC33EP32MC502-I/MM)
- Motor-control peripheral emphasis (против DSPIC33EP32GP502T-E/MM)
- Flash headroom within same footprint (против DSPIC33EP32MC203T-I/TL)
Заметки по проектированию
At the H grade's 150C maximum ambient, thermal budgeting is the primary design constraint. Estimated: use the exposed thermal pad of the 28-VQFN as the main heat path - tie it to a grounded copper pour of at least 2x2 cm with an array of thermal vias (0.3 mm drill, filled or capped) to spread heat into inner layers. Since the MCU load current is small, junction rise is usually modest, but ambient placement near power electronics in automotive modules demands verification with the junction-to-ambient figure from the family datasheet DS70000657J rather than assumption.
Decouple each VDD pin with a 100 nF ceramic capacitor placed within 2 mm of the pin, plus one bulk 4.7-10 uF capacitor near the device. The exposed pad must be soldered to ground - it is not optional - both for thermal performance and because it serves as a ground connection per the family datasheet. Keep the high-speed PWM output traces short and routed away from analog inputs AN0-AN5 to prevent switching noise coupling into ADC readings used by the control loop.
Confirm the exact footprint drawing (MM vs TL 28-pin VQFN land pattern) before qualifying DSPIC33EP32MC203T-I/TL as an alternate - same pin count does not always guarantee identical land-pattern dimensions between Microchip package codes. Also verify pin function mapping against the latest DS70000657 revision, since many pins are multiplexed and their behavior depends on configuration register settings. MCLR must be pulled up (4.7-10 kOhm typical) and held above VIH during ICSP programming.
Информация о соответствии
ROHS3 Compliant per distributor listing (full-electronic.com). AEC-Q100 automotive qualification per Hotenda/DigiKey listings. REACH, halogen-free, and conflict-minerals declarations not found in provided data.
