DSPIC33EP32MC502-E/MM - 16-bit 60MHz Motor Control DSC | Microchip
Артикул: DSPIC33EP32MC502-E/MM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.62 | $4,62 |
| 10 | $4.16 | $41,60 |
| 100 | $3.7 | $370,00 |
| 500 | $3.33 | $1.665,00 |
| 1.000 | $2.98 | $2.980,00 |
DSPIC33EP32MC502-E/MM Обзор
A digital signal controller combines the compute architecture of a microcontroller with the mathematical throughput of a DSP. In the power-management hierarchy of embedded systems, a DSC sits above general-purpose MCUs for control-loop-dominated tasks: it executes deterministic, high-frequency control algorithms such as field-oriented control (FOC) for electric motors, where cycle-accurate PWM generation and fast multiply-accumulate operations are mandatory.
Key features of the DSPIC33EP32MC502-E/MM include high-speed motor control PWM (MCPWM) peripherals with dead-time insertion, on-chip operational amplifiers and comparators for current-sense signal conditioning, a peripheral trigger generator (PTG) for autonomous sequencing, 4 DMA channels, and 5 timers. These peripherals offload the CPU, enabling tight single-shunt or three-shunt current loops without external analog circuitry.
The dsPIC33E core integrates DSP instructions (MAC, DSP multiply) with the enhanced mid-range peripheral ecosystem of Microchip's 16-bit platform. The -E/MM variant combines the extended automotive-style temperature rating with the thermally efficient QFN-S package, supporting high ambient-temperature industrial enclosures.
Typical applications include brushless DC (BLDC), permanent magnet synchronous (PMSM), and AC induction motor drives, digital power supplies such as LLC and PFC stages, and embedded motion control in HVAC, power tools, and e-mobility products.
A key design consideration: this part operates from a 2.5V to 3.6V single supply, so 5V current-sense signals require scaling or the on-chip op amps must be configured appropriately for the ADC input range.
This page synthesizes distributor pricing, same-footprint drop-in alternatives, and practical motor-control design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC33EP32MC502-E/MM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP32MC502-E/MM (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Qualification, Series, Supply Voltage.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP64MC502-E/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.05 / шт.
Открыть даташит →DSPIC33EP128MC502-E/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.2 / шт.
Открыть даташит →DSPIC33EP32MC202-E/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.3 / шт.
Открыть даташит →DSPIC33EP32GP502T-E/MM
✅ Прямая замена✓ В наличии
$2.98 / шт.
Открыть даташит →DSPIC33EP32MC502-I/MM
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP32MC502-E/MM Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC DSC |
| CPU Speed | 60 MHz |
| Core Performance | Up to 70 MIPS (dsPIC33E family) |
| Flash Program Memory | 32 KB |
| SRAM | 4 KB |
| DMA Channels | 4 |
| Timers | 5 |
| Motor Control PWM | Yes (MCPWM) |
| On-chip Op Amps | Yes |
| Comparators | Yes |
| Peripheral Trigger Generator | Yes (PTG) |
| Напряжение питания | 2.5 V to 3.6 V |
| Рабочая температура | -40C to +125C |
| Корпус | 28-QFN-S (6x6 mm), exposed pad |
| Тип монтажа | Surface Mount |
| Число выводов | 28 |
| Technology | CMOS |
Конфигурация выводов DSPIC33EP32MC502-E/MM
| Контакт 1 | MCLR — Master clear reset input / programming voltage |
| Контакт 2 | AN0/VREF+/CN2/RB0 — Analog input 0 / positive voltage reference |
| Контакт 3 | AN1/VREF-/CN3/RB1 — Analog input 1 / negative voltage reference |
| Контакт 4 | AN2/SS1/CN4/RB2 — Analog input 2 / SPI slave select |
| Контакт 5 | AN3/CN5/RB3 — Analog input 3 |
| Контакт 6 | AN4/CN6/RB4 — Analog input 4 |
| Контакт 7 | VDD — Power supply (2.5V to 3.6V) |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKI/CN7/RA2 — Crystal oscillator input / external clock |
| Контакт 10 | OSC2/CLKO/CN8/RA3 — Crystal oscillator output / clock output |
| Контакт 11 | RP15/CN11/RB5 — Remappable peripheral pin / change notification |
| Контакт 12 | RP14/CN12/RB6 — Remappable peripheral pin / change notification |
| Контакт 13 | RP13/CN13/RB7 — Remappable peripheral pin / change notification |
| Контакт 14 | RP12/CN14/RB8 — Remappable peripheral pin / change notification |
| Контакт 15 | RP11/CN15/RB9 — Remappable peripheral pin / change notification |
| Контакт 16 | RP10/PGD3/CN16/RB10 — Remappable pin / debug data channel 3 |
| Контакт 17 | RP9/PGC3/CN17/RB11 — Remappable pin / debug clock channel 3 |
| Контакт 18 | RP8/PGD2/CN18/RB12 — Remappable pin / debug data channel 2 |
| Контакт 19 | RP7/PGC2/CN19/RB13 — Remappable pin / debug clock channel 2 |
| Контакт 20 | VSS — Ground reference |
| Контакт 21 | VDD — Power supply (2.5V to 3.6V) |
| Контакт 22 | RP6/PGD1/CN24/RB14 — Remappable pin / primary debug data |
| Контакт 23 | RP5/PGC1/CN25/RB15 — Remappable pin / primary debug clock |
| Контакт 24 | RP4/CN1/RA0 — Remappable peripheral pin |
| Контакт 25 | RP3/CN0/RA1 — Remappable peripheral pin |
| Контакт 26 | RP2/AN6/CN9/RB1x — Remappable pin / analog input |
| Контакт 27 | RP1/AN7/CN10 — Remappable pin / analog input |
| Контакт 28 | AVDD/AVSS (EP) — Analog supply/ground; exposed pad connects to VSS |
Типичное применение
DSPIC33EP32MC502-E/MM подходит для 6 применениеs: Brushless DC (BLDC) Motor Drives, Digital Power Supplies (LLC / PFC), HVAC and Appliance Motion Control, Power Tools and E-Mobility, Solar Pump Inverters and Renewable Energy, Industrial Automation and Robotics.
Brushless DC (BLDC) Motor Drives
The DSPIC33EP32MC502-E/MM is purpose-built for BLDC and PMSM control: its MCPWM module produces complementary PWM pairs with hardware dead-time insertion, and the on-chip comparators implement cycle-by-cycle overcurrent limiting without CPU intervention. The 60 MHz (up to 70 MIPS) DSP core executes field-oriented control math comfortably at 20-50 kHz PWM frequencies, while the integrated op amps condition shunt-resistor current feedback directly into the ADC, eliminating external amplifier stages. Board designers typically pair it with a three-phase gate driver placed between the PWM outputs and the power MOSFET bridge; the exposed-pad QFN dissipates controller heat reliably in sealed motor housings up to +125C ambient.
Рекомендуется
Digital Power Supplies (LLC / PFC)
In digitally controlled AC-DC and DC-DC converters, this DSC handles PFC and LLC control loops with its high-resolution MCPWM and fast ADC triggered via the PTG for deterministic sampling instants aligned to switching events. The 70 MIPS core sustains voltage-mode or current-mode compensation at 100-500 kHz switching frequencies, and hardware comparators provide instant cycle-skipping or burst-mode protection. The 32 KB Flash accommodates full compensator firmware plus PMBus-style communication. Because the QFN exposed pad bonds to VSS, the power-ground reference stays clean; place the controller away from the LLC resonant tank and keep the ADC sense traces Kelvin-connected to the shunt resistors.
Рекомендуется
HVAC and Appliance Motion Control
Fan, compressor, and pump motors in HVAC systems and white goods benefit from sensorless FOC running on this DSC: the extended -40C to +125C rating covers outdoor condenser units and oven-adjacency environments, and sensorless algorithms (sliding-mode or back-EMF observers) fit comfortably in 32 KB Flash with headroom for communication. On-chip op amps enable single-shunt current sensing, cutting BOM cost versus three-shunt designs. The PTG offloads repetitive ADC/PWM sequencing so the CPU concentrates on the speed loop. Energy-efficiency regulations make quiet, efficient variable-speed operation mandatory; Microchip explicitly targets this family at quieter, longer-life motor systems.
Рекомендуется
Power Tools and E-Mobility
Cordless drill, e-bike, and scooter controllers demand compact, thermally robust control electronics. The 6x6 mm QFN-S fits dense controller boards constrained by handle geometry, and the -E temperature grade tolerates motor-compartment heat plus -40C cold starts for outdoor equipment. The 60 MHz core closes current loops fast enough for torque-ripple-free FOC on hub motors, and hardware comparators protect MOSFETs within microseconds of an overcurrent event, critical when a stalled rotor spikes phase current. Designers typically combine it with a step-down regulator for the 3.3V rail and gate drivers rated for the pack voltage; watchdog and brown-out modules safeguard firmware integrity under battery sag.
Рекомендуется
Solar Pump Inverters and Renewable Energy
Solar-powered water pumping requires a variable-frequency drive that maximizes energy harvest across irradiance conditions; this DSC runs maximum-power-point tracking plus sensorless motor control concurrently on its 70 MIPS core. The extended temperature range suits rooftop and desert installations, while 32 KB Flash holds MPPT, motor FOC, and fault-logging firmware with room for dry-run and tank-full logic. Hardware comparators implement instantaneous overcurrent shutdown for dry-run and locked-rotor events. The QFN-S exposed pad simplifies thermal design in sealed IP65 enclosures. Pair with an isolated gate driver and an I2C or UART link to a panel-level telemetry module for remote monitoring.
Рекомендуется
Industrial Automation and Robotics
In factory automation, this DSC drives servo-style axes, conveyor motors, and robotic joint actuators with deterministic FOC loops, while its DMA channels stream ADC samples without CPU loading and 5 timers coordinate multi-axis synchronization. UART, SPI, and I2C interfaces connect to encoders, and the PTG sequences peripheral operations autonomously for consistent loop timing. The 60 MHz clock supports position-loop rates beyond typical 10 kHz servo update frequencies, and the on-chip op amps condition resolver or hall-sensor signals. The -E temperature grade covers hot control cabinets. Microchip's MCHV-2 development board supports this family for rapid motor-control prototyping before PCB commit.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP32MC502-E/MM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP64MC502-E/MM | DSPIC33EP128MC502-E/MM | DSPIC33EP32GP502T-E/MM | DSPIC33EP32MC202-E/MM |
|---|---|---|---|---|---|
| Package | 28-QFN-S (6x6 mm) | 28-QFN-S (6x6 mm) - same | 28-QFN-S (6x6 mm) - same | 28-QFN-S (6x6 mm) - same | 28-QFN-S (6x6 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 32 KB | 64 KB | 128 KB | 32 KB | 32 KB |
| SRAM | 4 KB | 8 KB | 16 KB | 4 KB | 4 KB |
| CPU Clock | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
| Motor Control Peripherals (MCPWM/Op Amps) | Yes | Yes | Yes | No (GP peripheral set) | Yes (reduced set) |
Ключевые отличия
- Extended temperature grade (против DSPIC33EP32MC502-I/MM)
- Dedicated motor-control peripheral set (против DSPIC33EP32GP502T-E/MM)
- Flash headroom upgrade path on same footprint (против DSPIC33EP128MC502-E/MM)
Заметки по проектированию
The 28-QFN-S exposed pad is thermally and electrically tied to VSS. Solder it to a ground pour with an array of at least 9 vias to inner/outer ground planes; this is the primary heat removal path and omitting it can raise junction temperature by tens of degrees at full 60 MHz operation. Keep AVDD/AVSS on a separate filtered supply node via an LC or ferrite filter from VDD so ADC accuracy is not degraded by digital switching noise.
This DSC operates from 2.5V to 3.6V. In motor-drive systems powered from 12V, 24V, or 48V buses, use a dedicated LDO or buck for the 3.3V rail and add a bulk capacitor near the part plus 100 nF ceramics at each VDD pin. Enable brown-out reset at an appropriate trip point: during battery sag (common in power tools), an undervoltage core can corrupt Flash or mis-fire PWM gates into a short circuit.
Peripheral pin select (PPS) means UART/SPI/PWM functions must be explicitly mapped to RP pins in firmware before use; copying register configurations from the SOIC/S PDIP variant schematics without verifying the MM package pin map will mis-route signals. Also note the MM QFN-28 pinout differs from the SOIC-28 - the two are not footprint-compatible. Configure dead-time in the MCPWM module before enabling outputs to prevent shoot-through in the gate-driver stage.
Информация о соответствии
Compliance data was not explicitly provided in the retrieved web data. Current-production Microchip parts are typically RoHS/lead-free compliant; verify against Microchip's official product page or the distributor compliance certificate.
