DSPIC33EP512GP502-I/SO - 16-Bit 70 MIPS DSC, 512KB Flash | Microchip
Артикул: DSPIC33EP512GP502-I/SO ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $5.62 | $5,62 |
| 10 | $5.2 | $52,00 |
| 100 | $4.75 | $475,00 |
| 500 | $4.35 | $2.175,00 |
| 1.000 | $3.95 | $3.950,00 |
DSPIC33EP512GP502-I/SO Обзор
A Digital Signal Controller combines the peripheral set and ease of use of a microcontroller with the mathematical throughput of a DSP engine in a single core. In the power-management hierarchy, the dsPIC33EP family sits between general-purpose MCUs (such as the PIC24) and dedicated DSPs, making it the default choice for embedded digital power conversion, motor control, and sensor-signal-chain products that need both control code and real-time math on one chip.
Key features include the 70 MIPS dsPIC33E core with DSP instruction support and code-density improvements over the dsPIC33F generation, high-speed PWM outputs suited to digital power supplies, integrated analog peripherals (ADC, comparators, op amps, and CTMU charge-time measurement), and the Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. Communications cover CAN, UART, SPI, and I2C for industrial networking.
The device provides 4 DMA channels, 5 timers, and 15 interrupt sources per distributor documentation, with a CMOS process and low-power modes for battery-conscious designs. Flash self-programming supports field firmware updates, and the wide operating voltage range suits industrial supply rails.
Typical applications include digital power supplies and power-factor-correction converters, brushless DC and PMSM motor drives, and industrial control panels where CAN connectivity plus fast ADC sampling and PWM generation are required on a compact 28-pin footprint.
A key design consideration is clock configuration: the 70 MIPS performance requires correct PLL configuration (FOSC/2 instruction rate); designs must also budget the two oscillator pins consumed when an external crystal is used.
This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC33EP512GP502-I/SO — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP512GP502-I/SO (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Core Architecture, On-chip Op Amps, Series.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP256GP502-I/SO
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.32 / шт.
Открыть даташит →DSPIC33EP128GP502-I/SO
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP64GP502-I/SO
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP32GP502T-E/SO
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.42 / шт.
Открыть даташит →DSPIC33EP32MC202-I/SO
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.98 / шт.
Открыть даташит →DSPIC33EP512GP502-I/SO Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC33E DSC |
| Maximum CPU Speed | 70 MIPS |
| Максимальная тактовая частота | 60 MHz (per Microchip USA listing) |
| Flash Program Memory | 512 KB (170K x 24) |
| RAM | 48 KB |
| DMA Channels | 4 |
| Timers | 5 |
| Interrupt Sources | 15 |
| Корпус | 28-SOIC (0.295 in / 7.50 mm width) |
| Тип монтажа | Surface Mount |
| Process Technology | CMOS |
| Temperature Grade | -40C to +85C (Industrial, -I suffix) |
| Analog Peripherals | ADC, op amps, comparators, CTMU |
| Digital Peripherals | Hi-Speed PWM, PTG |
| Communication Interfaces | CAN, UART, SPI, I2C |
| Статус жизненного цикла | In Production |
Конфигурация выводов DSPIC33EP512GP502-I/SO
| Контакт 1 | MCLR — Master Clear reset input with power-up timer |
| Контакт 2 | AN0/VREF+/RB0 — Analog input 0 / positive voltage reference / Port B |
| Контакт 3 | AN1/VREF-/RB1 — Analog input 1 / negative voltage reference / Port B |
| Контакт 4 | AN2/PGD/RB2 — Analog input 2 / ICSP programming data / Port B |
| Контакт 5 | AN3/PGC/RB3 — Analog input 3 / ICSP programming clock / Port B |
| Контакт 6 | AN4/RB4 — Analog input 4 / Port B |
| Контакт 7 | AN5/RB5 — Analog input 5 / Port B |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKI — Oscillator input / external clock input |
| Контакт 10 | OSC2/CLKO/RC15 — Oscillator output / clock output / Port C |
| Контакт 11 | VDD — Positive supply |
| Контакт 12 | RB6 — Port B digital I/O (remappable peripheral capable) |
| Контакт 13 | RB7 — Port B digital I/O (remappable peripheral capable) |
| Контакт 14 | RB8 — Port B digital I/O (remappable peripheral capable) |
| Контакт 15 | RB9 — Port B digital I/O (remappable peripheral capable) |
| Контакт 16 | RB10 — Port B digital I/O (remappable peripheral capable) |
| Контакт 17 | RB11 — Port B digital I/O (remappable peripheral capable) |
| Контакт 18 | RC0 — Port C digital I/O (remappable peripheral capable) |
| Контакт 19 | RC1 — Port C digital I/O (remappable peripheral capable) |
| Контакт 20 | RC2 — Port C digital I/O (remappable peripheral capable) |
| Контакт 21 | RC3 — Port C digital I/O (remappable peripheral capable) |
| Контакт 22 | RC4 — Port C digital I/O (remappable peripheral capable) |
| Контакт 23 | RC5 — Port C digital I/O (remappable peripheral capable) |
| Контакт 24 | RC6 — Port C digital I/O (remappable peripheral capable) |
| Контакт 25 | RC7 — Port C digital I/O (remappable peripheral capable) |
| Контакт 26 | VSS — Ground reference |
| Контакт 27 | AVDD — Analog positive supply |
| Контакт 28 | VDD — Positive supply |
Типичное применение
DSPIC33EP512GP502-I/SO подходит для 6 применениеs: Digital Power Supplies and PFC, Brushless DC and PMSM Motor Drives, Industrial Control with CAN Networking, Analog Sensor Signal Processing, Portable and Battery-Powered Instruments, Embedded Lighting and Power Conversion Control.
Digital Power Supplies and PFC
The DSPIC33EP512GP502-I/SO fits digital power conversion because its 70 MIPS DSP core closes voltage and current loops fast enough for switching frequencies in the hundreds of kHz, while the high-speed PWM module provides fine duty-cycle resolution and complementary outputs with dead-time control. On-chip op amps condition shunt-current signals without external amplifiers, and comparators enable cycle-by-cycle overcurrent protection with sub-microsecond response. Placed as the controller on an AC-DC or DC-DC converter board, the 4 DMA channels keep ADC sampling deterministic under interrupt load. The trade-off versus a dedicated digital-power IC is firmware development effort, offset by full algorithm flexibility and a 512 KB Flash budget for adaptive control plus field-updatable firmware over UART or CAN.
Рекомендуется
Brushless DC and PMSM Motor Drives
For sensorless BLDC and PMSM control, the DSPIC33EP512GP502-I/SO pairs its 70 MIPS DSP engine (MAC and multiply instructions for field-oriented-control math) with high-speed PWM, integrated op amps for phase-current sensing, and comparators for hardware overcurrent trips. The fast ADC samples back-EMF or current-shunt signals synchronously with PWM via the Peripheral Trigger Generator, removing software jitter from the sampling instant. On a compact 28-SOIC footprint, the device handles the complete control loop plus UART or CAN communication to a host. Memory headroom of 512 KB allows sensorless FOC, startup state machines, and field-update bootloaders to coexist. Designs needing only trapezoidal six-step control can use the smaller-footprint-print DSPIC33EP32MC202-I/SO as a drop-in cost reduction.
Рекомендуется
Industrial Control with CAN Networking
In industrial nodes such as pump controllers, HVAC boards, and sensor concentrators, the DSPIC33EP512GP502-I/SO provides an integrated CAN 2.0B controller alongside UART, SPI, and I2C, eliminating an external CAN transceiver-controller chip. The 70 MIPS core services protocol stacks and application logic concurrently, while 4 DMA channels offload serial data movement. The industrial -40C to +85C temperature grade of the -I suffix matches factory-floor ambient requirements, and the 28-SOIC 7.50 mm package suits both hand assembly and automated SMT lines. On-chip CTMU supports capacitive touch buttons for panel interfaces. The 512 KB Flash accommodates future protocol additions without a hardware spin, a common decision factor versus 32 KB-footprint siblings in long-lived industrial products.
Рекомендуется
Analog Sensor Signal Processing
The DSPIC33EP512GP502-I/SO serves front-end signal chains by combining its on-chip ADC with op amps, comparators, and the CTMU charge-time measurement unit, allowing sensor signals such as pressure bridges, thermistors, and capacitive elements to be conditioned and digitized without external analog ICs. The 70 MIPS DSP instruction set runs filtering (IIR/FIR), FFT, and calibration math in real time, while 48 KB of RAM buffers sample blocks for analysis or logging. The Peripheral Trigger Generator sequences ADC conversions from PWM or timer events for coherent sampling. In a 28-SOIC footprint the device replaces MCU-plus-op-amp-plus-ADC multi-chip designs, cutting BOM cost and board area, with the trade-off that precision specifications are good-not-instrumentation-grade for the most demanding metrology.
Рекомендуется
Portable and Battery-Powered Instruments
Handheld meters, testers, and battery analyzers benefit from the DSPIC33EP512GP502-I/SO's low-power modes, which let the 70 MIPS core idle between measurements and wake on interrupt, extending battery life. The CTMU enables capacitive touch and precise time-charge measurements for test functions, while the ADC and op amps read battery voltage and current directly. A single 3.3V-supply CMOS device operating from -40C to +85C simplifies power design, and the 28-SOIC 7.50 mm body fits compact two-layer instrument boards. The 512 KB Flash supports rich UI firmware, multi-protocol communication, and datalogging buffers within the 48 KB RAM. Field firmware updates over UART protect against obsolescence in products with long service lives, an advantage over fixed-function analog meter ICs.
Рекомендуется
Embedded Lighting and Power Conversion Control
Advanced LED drivers, HID ballasts, and small inverters use the DSPIC33EP512GP502-I/SO because its high-speed PWM delivers the fine resolution and phase-shifted outputs needed for dimming and resonant conversion topologies, while integrated comparators provide fast fault shutdown independent of CPU latency. The 70 MIPS DSP core runs power-conversion compensation loops and communication (UART, SPI, I2C, CAN) for digital lighting networks on one chip. The 28-SOIC package withstands the moderate temperatures of lighting enclosures within its -40C to +85C grade, and the 4 DMA channels maintain ADC synchronization for ripple and current regulation. Compared with fixed-function lighting controllers, this DSC offers programmable dimming curves, protocol adaptability, and remote firmware updates in the same 512 KB Flash footprint.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP512GP502-I/SO — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP256GP502-I/SO | DSPIC33EP128GP502-I/SO | DSPIC33EP64GP502-I/SO | DSPIC33EP32GP502T-E/SO | DSPIC33EP32MC202-I/SO |
|---|---|---|---|---|---|---|
| Package | 28-SOIC (7.50 mm) | 28-SOIC (7.50 mm) - same | 28-SOIC (7.50 mm) - same | 28-SOIC (7.50 mm) - same | 28-SOIC (7.50 mm) - same | 28-SOIC (7.50 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Speed | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Flash Memory | 512 KB (170K x 24) | 256 KB | 128 KB | 64 KB | 32 KB | 32 KB |
| Temperature Range | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (Extended) | -40C to +85C |
| Peripheral Family Variant | GP (general purpose, op amps + CTMU) | GP | GP | GP | GP | MC (motor control analog set) |
| Lifecycle Status | In Production (Active) | In Production | In Production | In Production | In Production | In Production |
Ключевые отличия
- Largest Flash in the 28-SOIC dsPIC33EP GP family (против DSPIC33EP256GP502-I/SO)
- General-purpose analog set including op amps and CTMU (против DSPIC33EP32MC202-I/SO)
- Honest trade-off: industrial-only temperature grade (против DSPIC33EP32GP502T-E/SO)
Заметки по проектированию
Decouple both VDD pins (11 and 28) and AVDD (pin 27) individually with 0.1 uF ceramic capacitors placed within 3 mm of each pin, plus one bulk 4.7-10 uF capacitor near the device. AVDD should be filtered from the digital rail (ferrite bead or RC) to preserve ADC accuracy; Microchip's analog performance specifications assume a clean AVDD. Tie all VSS pins (8, 26) to a solid ground plane - do not daisy-chain grounds through the analog section, as return-current coupling degrades converter results in PWM-heavy applications.
Use the ICSP pins (MCLR pin 1, PGD on pin 4, PGC on pin 5) with a standard 5-pin programming header routed away from PWM and switching nodes; series 100-ohm resistors on PGD/PGC isolate programmer loading in-circuit. Keep the crystal loop (OSC1/OSC2, pins 9-10) compact with guard grounding per Microchip's oscillator layout guidance. Because Peripheral Pin Select lets UART/PWM appear on many pins, finalize RPn mapping early in layout so serial and analog functions avoid crossing the analog half of the footprint.
Three frequent mistakes: (1) Confusing the 60 MHz FOSC figure with the 70 MIPS instruction rate - the core runs at FOSC/2, so verify PLL settings in the configuration bits before benchmarking. (2) Leaving MCLR floating; use the internal pull-up or an external 10k resistor plus a small capacitor for robust power-on reset. (3) Migrating firmware from dsPIC33F without reviewing changed peripheral register maps - the E-generation PPS, ADC, and PWM registers differ substantially from the F generation. Always recompile against the dsPIC33EP device support files rather than reusing F-family linker scripts.
Информация о соответствии
Compliance data was not explicitly stated in the retrieved web data. As a current-production Microchip SMD device, RoHS/lead-free compliance is typical but must be confirmed via the Microchip product page compliance portal. The -I suffix denotes industrial temperature grade, not a compliance marking.
