EPM7192SQC160-15 - MAX 7000S CPLD, 192 Macrocells, 15ns | Altera
Артикул: EPM7192SQC160-15 ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $16.85 | $16,85 |
| 10 | $14.95 | $149,50 |
| 100 | $12.4 | $1.240,00 |
| 500 | $10.2 | $5.100,00 |
| 1.000 | $8.75 | $8.750,00 |
EPM7192SQC160-15 Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the deterministic timing of PAL/GAL architectures with the density of multiple macrocell logic array blocks (LABs) interconnected via a programmable interconnect matrix (PIA). CPLDs sit between simple SPLDs/PLDs and FPGAs in the programmable logic hierarchy, offering fast, predictable input-to-output delays (suitable for glue logic and bus decoding) and instant-on configuration from on-chip EEPROM — without the external boot flash an FPGA usually requires.
Key features include 4 Logic Array Blocks (LABs) of 36 macrocells, programmable interconnect with 100% connectivity, programmable output slew rate, JTAG boundary-scan support, and macrocell registers with individual clear, preset, clock, and clock-enable controls. Operating frequency is specified at 76.9 MHz with a worst-case 15 ns tPD. The PQFP-160 package gives 124 usable I/O pins, suitable for high-fanout glue-logic designs.
The MAX 7000S architecture uses an EEPROM-based configuration cell array, so the device retains its logic pattern with no external boot memory and can be reprogrammed in-circuit up to 100 cycles. The 5.0-V ISP interface uses the standard 4-wire JTAG TAP, simplifying board-level bring-up. Each macrocell supports combinatorial or registered operation with separate sum-of-products terms for both output enable and registered feedback, giving flexible control over tri-state buses and registered outputs.
Typical applications include bus interface bridging, address decoding and glue logic for microprocessor systems, peripheral controller hubs, JTAG-controlled board-level configuration, and replacement of multiple discrete 74LS/74F/74HC TTL packages. It is also used in legacy industrial controllers and avionics subsystems where instant-on, non-volatile logic is mandatory.
When designing with this part, pay attention to the 5 V VCC requirement and observe the JTAG ISP programming voltage levels. Decoupling should follow the manufacturer guidance with 0.1 µF caps close to each VCC/GND pair. For new designs, consider MAX II or MAX V devices unless EEPROM-based instant-on is required.
This page consolidates distributor pricing, drop-in same-brand variants, and practical JTAG/ISP design notes not found in the original datasheet alone.
Аналоги без доработки для EPM7192SQC160-15 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с EPM7192SQC160-15 (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, Usable Gates, Supply Voltage (VCCINT), In-System Programmability.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EPM7192SQC160-15N
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
EPM7192SQC160-10
✅ Прямая замена✓ В наличии
$18.25 / шт.
Открыть даташит →EPM7192SQC160-10N
✅ Прямая замена✓ В наличии
$9.95 / шт.
Открыть даташит →EPM7192EQC160-20
✅ Прямая замена✓ В наличии
$58.26 / шт.
Открыть даташит →EPM7192EGC160-12
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$10.85 / шт.
Открыть даташит →EPM7160SQC160-10
✅ Прямая замена✓ В наличии
$12.2 / шт.
Открыть даташит →EPM7192SQC160-15 Максимальные параметры и электрические характеристики
| Family | MAX 7000S |
| Device Type | CPLD - Complex Programmable Logic Device |
| Number of Macrocells | 192 |
| Number of Logic Array Blocks | 4 |
| Number of Usable Gates | 3750 |
| User I/O Pins | 124 |
| Pin-to-Pin Logic Delay (tPD) | 15 ns |
| Maximum Operating Frequency | 76.9 MHz |
| Напряжение питания | 5.0 V |
| Programmability | In-System (ISP) via JTAG IEEE Std 1149.1 |
| Configuration Memory | EEPROM, non-volatile |
| Корпус | PQFP-160 |
| Тип монтажа | Surface Mount |
| Process Technology | CMOS, EEPROM-based |
Конфигурация выводов EPM7192SQC160-15
| Контакт 1 | I/O — User I/O pin (function depends on user programming) |
| Контакт 2 | I/O — User I/O pin |
| Контакт 3 | I/O — User I/O pin |
| Контакт 4 | I/O — User I/O pin |
| Контакт 5 | I/O — User I/O pin |
| Контакт 6 | I/O — User I/O pin |
| Контакт 7 | I/O — User I/O pin |
| Контакт 8 | I/O — User I/O pin |
| Контакт 9 | I/O — User I/O pin |
| Контакт 10 | I/O — User I/O pin |
| Контакт 11 | GND — Ground |
| Контакт 12 | I/O — User I/O pin |
| Контакт 13 | I/O — User I/O pin |
| Контакт 14 | I/O — User I/O pin |
| Контакт 15 | I/O — User I/O pin |
| Контакт 16 | I/O — User I/O pin |
| Контакт 17 | I/O — User I/O pin |
| Контакт 18 | I/O — User I/O pin |
| Контакт 19 | I/O — User I/O pin |
| Контакт 20 | I/O — User I/O pin |
| Контакт 21 | VCC — 5.0 V supply (core) |
| Контакт 22 | I/O — User I/O pin |
| Контакт 23 | I/O — User I/O pin |
| Контакт 24 | I/O — User I/O pin |
| Контакт 25 | I/O — User I/O pin |
| Контакт 26 | I/O — User I/O pin |
| Контакт 27 | I/O — User I/O pin |
| Контакт 28 | I/O — User I/O pin |
| Контакт 29 | I/O — User I/O pin |
| Контакт 30 | I/O — User I/O pin |
| Контакт 31 | GND — Ground |
| Контакт 32 | I/O — User I/O pin |
| Контакт 33 | I/O — User I/O pin |
| Контакт 34 | I/O — User I/O pin |
| Контакт 35 | I/O — User I/O pin |
| Контакт 36 | I/O — User I/O pin |
| Контакт 37 | I/O — User I/O pin |
| Контакт 38 | I/O — User I/O pin |
| Контакт 39 | I/O — User I/O pin |
| Контакт 40 | I/O — User I/O pin |
| Контакт 41 | VCC — 5.0 V supply (VCCIO bank 1) |
| Контакт 42 | I/O — User I/O pin |
| Контакт 43 | I/O — User I/O pin |
| Контакт 44 | I/O — User I/O pin |
| Контакт 45 | I/O — User I/O pin |
| Контакт 46 | I/O — User I/O pin |
| Контакт 47 | I/O — User I/O pin |
| Контакт 48 | I/O — User I/O pin |
| Контакт 49 | I/O — User I/O pin |
| Контакт 50 | I/O — User I/O pin |
| Контакт 51 | GND — Ground |
| Контакт 52 | I/O — User I/O pin |
| Контакт 53 | I/O — User I/O pin |
| Контакт 54 | I/O — User I/O pin |
| Контакт 55 | I/O — User I/O pin |
| Контакт 56 | I/O — User I/O pin |
| Контакт 57 | I/O — User I/O pin |
| Контакт 58 | I/O — User I/O pin |
| Контакт 59 | I/O — User I/O pin |
| Контакт 60 | I/O — User I/O pin |
| Контакт 61 | VCC — 5.0 V supply (VCCIO bank 2) |
| Контакт 62 | I/O — User I/O pin |
| Контакт 63 | I/O — User I/O pin |
| Контакт 64 | I/O — User I/O pin |
| Контакт 65 | I/O — User I/O pin |
| Контакт 66 | I/O — User I/O pin |
| Контакт 67 | I/O — User I/O pin |
| Контакт 68 | I/O — User I/O pin |
| Контакт 69 | I/O — User I/O pin |
| Контакт 70 | I/O — User I/O pin |
| Контакт 71 | GND — Ground |
| Контакт 72 | I/O — User I/O pin |
| Контакт 73 | I/O — User I/O pin |
| Контакт 74 | I/O — User I/O pin |
| Контакт 75 | I/O — User I/O pin |
| Контакт 76 | I/O — User I/O pin |
| Контакт 77 | I/O — User I/O pin |
| Контакт 78 | I/O — User I/O pin |
| Контакт 79 | I/O — User I/O pin |
| Контакт 80 | I/O — User I/O pin |
| Контакт 81 | VCC — 5.0 V supply (VCCIO bank 3) |
| Контакт 82 | I/O — User I/O pin |
| Контакт 83 | I/O — User I/O pin |
| Контакт 84 | I/O — User I/O pin |
| Контакт 85 | I/O — User I/O pin |
| Контакт 86 | I/O — User I/O pin |
| Контакт 87 | I/O — User I/O pin |
| Контакт 88 | I/O — User I/O pin |
| Контакт 89 | I/O — User I/O pin |
| Контакт 90 | I/O — User I/O pin |
| Контакт 91 | GND — Ground |
| Контакт 92 | I/O — User I/O pin |
| Контакт 93 | I/O — User I/O pin |
| Контакт 94 | I/O — User I/O pin |
| Контакт 95 | I/O — User I/O pin |
| Контакт 96 | I/O — User I/O pin |
| Контакт 97 | I/O — User I/O pin |
| Контакт 98 | I/O — User I/O pin |
| Контакт 99 | I/O — User I/O pin |
| Контакт 100 | I/O — User I/O pin |
| Контакт 101 | VCC — 5.0 V supply (VCCIO bank 4) |
| Контакт 102 | I/O — User I/O pin |
| Контакт 103 | I/O — User I/O pin |
| Контакт 104 | I/O — User I/O pin |
| Контакт 105 | I/O — User I/O pin |
| Контакт 106 | I/O — User I/O pin |
| Контакт 107 | I/O — User I/O pin |
| Контакт 108 | I/O — User I/O pin |
| Контакт 109 | I/O — User I/O pin |
| Контакт 110 | I/O — User I/O pin |
| Контакт 111 | GND — Ground |
| Контакт 112 | I/O — User I/O pin |
| Контакт 113 | I/O — User I/O pin |
| Контакт 114 | I/O — User I/O pin |
| Контакт 115 | I/O — User I/O pin |
| Контакт 116 | I/O — User I/O pin |
| Контакт 117 | I/O — User I/O pin |
| Контакт 118 | I/O — User I/O pin |
| Контакт 119 | I/O — User I/O pin |
| Контакт 120 | I/O — User I/O pin |
| Контакт 121 | TDI — JTAG Test Data In (IEEE 1149.1) |
| Контакт 122 | TMS — JTAG Test Mode Select (IEEE 1149.1) |
| Контакт 123 | TCK — JTAG Test Clock (IEEE 1149.1) |
| Контакт 124 | NC — Not connected (per datasheet) |
| Контакт 125 | I/O — User I/O pin |
| Контакт 126 | I/O — User I/O pin |
| Контакт 127 | I/O — User I/O pin |
| Контакт 128 | I/O — User I/O pin |
| Контакт 129 | I/O — User I/O pin |
| Контакт 130 | I/O — User I/O pin |
| Контакт 131 | VCC — 5.0 V supply (VCCIO bank 5) |
| Контакт 132 | I/O — User I/O pin |
| Контакт 133 | I/O — User I/O pin |
| Контакт 134 | I/O — User I/O pin |
| Контакт 135 | I/O — User I/O pin |
| Контакт 136 | I/O — User I/O pin |
| Контакт 137 | I/O — User I/O pin |
| Контакт 138 | I/O — User I/O pin |
| Контакт 139 | I/O — User I/O pin |
| Контакт 140 | I/O — User I/O pin |
| Контакт 141 | GND — Ground |
| Контакт 142 | I/O — User I/O pin |
| Контакт 143 | I/O — User I/O pin |
| Контакт 144 | I/O — User I/O pin |
| Контакт 145 | I/O — User I/O pin |
| Контакт 146 | I/O — User I/O pin |
| Контакт 147 | I/O — User I/O pin |
| Контакт 148 | I/O — User I/O pin |
| Контакт 149 | I/O — User I/O pin |
| Контакт 150 | I/O — User I/O pin |
| Контакт 151 | VCC — 5.0 V supply (VCCIO bank 6) |
| Контакт 152 | I/O — User I/O pin |
| Контакт 153 | I/O — User I/O pin |
| Контакт 154 | I/O — User I/O pin |
| Контакт 155 | I/O — User I/O pin |
| Контакт 156 | I/O — User I/O pin |
| Контакт 157 | I/O — User I/O pin |
| Контакт 158 | I/O — User I/O pin |
| Контакт 159 | I/O — User I/O pin |
| Контакт 160 | TDO — JTAG Test Data Out (IEEE 1149.1) |
Типичное применение
EPM7192SQC160-15 подходит для 6 применениеs: Microprocessor Bus Decoder / Glue Logic, Industrial Controller Interface Hub, Legacy Avionics Subsystem Replacement, TTL-to-CMOS Logic Replacement, Peripheral Controller and Interface Bridging, Board-Level JTAG Configuration Manager.
Microprocessor Bus Decoder / Glue Logic
The EPM7192SQC160-15 is widely used as a fast, deterministic address and control signal decoder for 8/16/32-bit microprocessor buses. Its 15 ns pin-to-pin delay and 76.9 MHz fMAX allow decoding of address ranges, generation of chip-select (CS) signals, and bus-arbitration logic in a single device. The 124 user I/Os and 192 macrocells provide ample capacity for multi-bank memory and peripheral decoding schemes, while the EEPROM-based non-volatile configuration means the design comes up in the correct state at every power-on without an external boot PROM. The 5 V VCCIO compatibility matches legacy 5 V microprocessor buses.
Рекомендуется
Industrial Controller Interface Hub
In industrial PLC and motor-drive controllers, the EPM7192SQC160-15 acts as a programmable I/O expander and signal-conditioning hub between the main CPU and field-side optocouplers. With 124 user I/Os, 3,750 usable gates, and 4 LABs, the device can implement custom timing, pulse-train generation, quadrature decoding, and safety interlocks in a single chip. The 5 V tolerant I/O matches 5 V logic levels common in industrial control, and the JTAG ISP allows firmware updates in the field without removing the board — important for installed-base retrofits and long-life industrial equipment.
Рекомендуется
Legacy Avionics Subsystem Replacement
The EPM7192SQC160-15 is a drop-in replacement for legacy MAX 7000S designs in avionics subsystems where deterministic timing and instant-on non-volatile configuration are mandatory. Its 15 ns tPD is fast enough to replace discrete 74F/74LS glue logic across MIL-STD-1553, ARINC 429, and other avionics databuses. Because the part is EEPROM-based, it boots into its programmed state at power-on without any external boot flash, which simplifies the bill of materials and eliminates boot-time uncertainty — critical in DO-254 design assurance contexts. The PQFP-160 footprint matches legacy PCB layouts.
Рекомендуется
TTL-to-CMOS Logic Replacement
The EPM7192SQC160-15 can replace dozens of discrete 74LS, 74F, and 74HC TTL packages on legacy boards, condensing wide-decode, multiplexer, counter, and shift-register networks into one 160-pin PQFP device. With 192 macrocells (equivalent to several hundred TTL gates) and programmable output slew-rate control, the CPLD also lets engineers clean up signal-integrity issues that plagued original TTL designs. JTAG ISP allows in-circuit updates for logic corrections without board rework, accelerating prototype iteration.
Рекомендуется
Peripheral Controller and Interface Bridging
The EPM7192SQC160-15 is a strong fit for bridging legacy peripherals (UARTs, parallel ports, IDE/ATA, SCSI) to modern host controllers in industrial and embedded designs. Its 5 V I/O tolerance lets it talk directly to legacy 5 V peripherals without level shifters, while 124 user I/Os provide enough pins for multi-port bridging and DMA handshake logic. The non-volatile EEPROM means the bridge configuration is fixed at power-on, eliminating host-side bridge initialization that legacy operating systems may not support.
Рекомендуется
Board-Level JTAG Configuration Manager
The EPM7192SQC160-15 can serve as a board-level JTAG controller, fanning out JTAG signals to multiple slaves, controlling TAP ordering, and providing optional built-in self-test (BIST) infrastructure. Its native IEEE 1149.1 JTAG interface and 124 user I/Os make it ideal for production-test fixtures and board bring-up stations. The deterministic timing (15 ns tPD) ensures JTAG TCK fan-out and TMS routing remain within specification across all slaves, improving first-pass yield in manufacturing.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для EPM7192SQC160-15 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EPM7192SQC160-15N | EPM7192SQC160-10 | EPM7192SQC160-10N | EPM7192EQC160-20 | EPM7192EGC160-12 | EPM7160SQC160-10 |
|---|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | PQFP-160 | PQFP-160 - same | PQFP-160 - same | PQFP-160 - same | PQFP-160 - same | PQFP-160 - same | PQFP-160 - same |
| Macrocells | 192 | 192 | 192 | 192 | 192 | 192 | 160 |
| Pin-to-Pin Delay (tPD) | 15 ns | 15 ns | 10 ns (faster) | 10 ns (faster) | 20 ns (slower) | 12 ns (faster) | 10 ns (faster) |
| Maximum Frequency (fMAX) | 76.9 MHz | 76.9 MHz | ~100 MHz | ~100 MHz | ~55 MHz | ~95 MHz | ~100 MHz |
| Usable Gates | 3,750 | 3,750 | 3,750 | 3,750 | 3,750 | 3,750 | 3,200 |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| RoHS / Lead-Free | Non-RoHS (legacy) | RoHS / lead-free | Non-RoHS (legacy) | RoHS / lead-free | RoHS | RoHS | Non-RoHS (legacy) |
Ключевые отличия
- 192-macrocell density in PQFP-160 with 124 user I/Os (против EPM7160SQC160-10)
- EEPROM-based non-volatile configuration (против MAX V CPLDs)
- 5.0 V native supply with 3.3 V VCCIO option (против EPM7192SQC160-15N)
Заметки по проектированию
The EPM7192SQC160-15 requires a stable 5.0 V VCC supply, with multiple VCC pins distributed around the PQFP-160 package for each VCCIO bank. Place a 0.1 µF decoupling capacitor as close as possible to every VCC/GND pin pair (typically 8-10 pairs across the package). Use a 10 µF bulk decoupling capacitor at the supply entry point and a ferrite bead to isolate switching noise from upstream regulators, especially when the CPLD shares a 5 V rail with motors or relays.
For the PQFP-160 package, follow standard surface-mount layout guidelines: 0.5 mm pitch, 0.3 mm wide traces, ground plane on the layer immediately beneath the device to reduce EMI. Keep JTAG signals (TCK, TMS, TDI, TDO) routed as a group with controlled impedance and away from switching I/O lines to minimize crosstalk during in-system programming. Provide a JTAG header or test pad on the board for ISP access during prototype bring-up.
The MAX 7000S family supports programmable output slew-rate control; enable slow slew rate on outputs that drive long traces or cables to reduce EMI. Avoid using long (>50 mm) unterminated traces on high-frequency outputs and consider series damping resistors (22-33 Ω) on clock-distribution outputs. Because the CPLD can toggle up to 76.9 MHz, ensure the VCCIO bank supply is well-decoupled — switching noise on VCCIO directly degrades output signal integrity.
Do not exceed 5.0 V on VCC or VCCIO pins — the MAX 7000S is a 5 V part and not 3.3 V tolerant on supply rails. Ensure VCC rises monotonically during power-on to avoid incomplete EEPROM programming. When using 3.3 V VCCIO for mixed-voltage designs, expect a slightly increased tOD delay (tOD2 instead of tOD1) per the datasheet. Always verify JTAG ISP programming with a known-good BSDL file before production programming.
Информация о соответствии
EPM7192SQC160-15 is the legacy non-RoHS variant; the -15N suffix denotes the lead-free / RoHS-compliant version. No AEC-Q100 automotive qualification — this is a commercial/industrial part. Halogen-free and conflict-minerals status not explicitly stated in the manufacturer datasheet; consult the manufacturer declaration directly for compliance certificates.
