Texas Instruments

INA111APG4 - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

Артикул: INA111APG4 ✓ Активен
500 µV maximum Vdss 20 pA maximum Id 8-pin plastic DIP Package
MOQ: 1 |

INA111APG4 Обзор

Texas Instruments INA111APG4 is a high-speed FET-input instrumentation amplifier with one internal amplifier circuit, a 2 MHz bandwidth, a maximum input bias current of 20 pA, a maximum input offset voltage of 500 µV, and an 8-pin plastic DIP package. It is designed for precision differential-signal conditioning where low bias current, high common-mode rejection, and fast signal response are important.

An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. Its internal three-op-amplifier architecture provides high input impedance and consistent gain-setting behavior. This places the INA111 in the amplifier hierarchy of analog ICs and instrumentation amplifiers, where it supports sensor interfaces, bridge amplifiers, current measurement, and laboratory acquisition systems without requiring a separate input-buffer stage.

Principal features include a maximum input bias current of 20 pA, a maximum input offset voltage of 500 µV, a maximum offset-voltage drift of 5 µV/°C, and a minimum common-mode rejection ratio of 106 dB. The device also provides high-speed operation with a listed 2 MHz bandwidth. These characteristics make it especially useful when the source presents very high impedance, when small differential signals must be measured in the presence of a much larger common-mode voltage, or when measurement bandwidth must exceed that of a general-purpose precision amplifier.

The INA111 uses a three-amplifier instrumentation-amplifier architecture. Its FET input stage limits input bias current, while the differential signal is amplified according to an external gain-setting resistor. The listed 106 dB minimum common-mode rejection helps suppress common-mode voltage in industrial sensor systems, while the 2 MHz bandwidth allows the device to process signals beyond the static-measurement range associated with many precision op amps. Its single-ended output is intended for use with external analog-to-digital converters, filters, and downstream acquisition circuitry.

Typical applications include low-current sensor conditioning, strain-gauge and resistance-bridge measurement, precision current sensing, high-impedance laboratory probes, and industrial process-monitoring inputs. In a bridge circuit, the amplifier converts a small differential bridge excitation into a larger single-ended voltage. In a current-shunt system, its low bias current minimizes measurement error from high-resistance sense lines, while the high common-mode rejection helps preserve accuracy when the shunt signal is superimposed on a larger supply voltage.

Design should preserve the distinction between input bias current, input offset voltage, and the common-mode voltage range. Place the gain-setting resistor close to the appropriate device pins, route sensitive input traces away from switching nodes and power-converter currents, and use a suitable reference arrangement when the output must remain centered in a unipolar converter range. Verify bandwidth, output-swing limits, supply headroom, and input protection against the actual sensor and ADC requirements.

This page combines manufacturer specifications, package and ordering information, comparison parameters, and practical circuit-design guidance for engineers evaluating the INA111APG4 as a high-speed FET-input instrumentation amplifier.

Аналоги без доработки для INA111APG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с INA111APG4 (тот же форм-фактор и посадочное место) — отличается по Common-Mode Rejection Ratio, Input Bias Current, Mounting Type, Package.

Texas Instruments
Common-Mode Rejection Ratio: 106 dB
Input Bias Current: Less than 20 pA
Mounting Type: Surface mount
Сравнить с INA111APG4 →

INA111BU

✅ Прямая замена
Texas Instruments
📦 8-pin plastic DIP
Instrumentation amplifier · 1 circuit · FET-input · 2 MHz · 17 V/us · 106 dB · Less than 20 pA · 6 V to 18 V

Уточнить цену

Открыть даташит →

INA114APG4

✅ Прямая замена
📦 8-pin plastic DIP
Uses the same three-op-amplifier architecture and 8-pin DIP package, but is optimized for precision rather than the INA111 high-speed position.

📋 Справочный аналог (нет в каталоге)

INA111APG4 Максимальные параметры и электрические характеристики

Amplifier Type Instrumentation amplifier
Number of Amplifier Circuits 1 circuit
Internal Architecture 3-op-amplifier design
Input Bias Current 20 pA maximum
Input Offset Voltage 500 µV maximum
Input Offset Voltage Drift 5 µV/°C maximum
Common-Mode Rejection Ratio 106 dB minimum
Bandwidth 2 MHz
Тип выхода Single-ended
Корпус 8-pin plastic DIP
Тип монтажа Through-hole
Статус RoHS RoHS compliant

Руководство по цоколевке INA111APG4 в корпусе 8-pin plastic dip

Цоколевка для INA111APG4 (корпус 8-pin plastic dip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса 8-pin plastic dip для INA111APG4

Нет подробных данных о распиновке для INA111APG4.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

INA111APG4 подходит для 6 применениеs: Precision Bridge Sensor Conditioning, High-Impedance Probe Amplification, Low-Current Shunt Measurement, Industrial Process Measurement, Laboratory Data Acquisition, Audio and Analog Signal Conditioning.

🏭

Precision Bridge Sensor Conditioning

The INA111APG4 is well suited to strain-gauge, load-cell, and resistive-bridge measurement because its 20 pA maximum input bias current limits the error introduced by high source impedance. Its 106 dB minimum common-mode rejection helps isolate the small differential bridge signal from excitation-related common-mode voltage. Place the device close to the bridge, route the two signal inputs symmetrically, and use the external gain-setting resistor to establish the required sensitivity. The 2 MHz bandwidth also leaves headroom for mechanical resonances and filtering above the primary measurement bandwidth. A suitable companion is the ADS1262IPW when a high-resolution converter is required.

🧩

High-Impedance Probe Amplification

The INA111APG4 can amplify signals from electrochemical, capacitive, or laboratory probes whose source impedance is high enough that input bias current matters. The listed maximum input bias current of 20 pA helps preserve sensor fidelity, while the minimum common-mode rejection ratio of 106 dB supports systems in which the common-mode voltage is much larger than the signal of interest. For practical layouts, minimize exposed trace area, use guarding where leakage can affect the measurement, and keep input capacitance low to preserve response. The device’s 2 MHz bandwidth makes it appropriate when the measurement includes content beyond static DC.

⚡

Low-Current Shunt Measurement

For low-current power monitoring, the INA111APG4 can amplify the differential voltage across a shunt while rejecting the supply-related common-mode voltage. Its 20 pA maximum input bias current is particularly helpful when using long, high-impedance sense connections that could otherwise introduce error. The common-mode rejection ratio of at least 106 dB supports accurate extraction of a relatively small shunt signal. Keep the Kelvin sense traces paired and away from high-current switching paths, and check the shunt’s power dissipation separately from the amplifier’s operating limits. The INA240A4DR is a useful alternative when the design requires a dedicated bidirectional current-sensing amplifier instead.

🏭

Industrial Process Measurement

The INA111APG4 is applicable to industrial process signals that arrive as small differential voltages over substantial common-mode voltage. Its 106 dB minimum common-mode rejection supports reliable extraction of sensor information in electrically noisy equipment, while the high-speed response can accommodate rapidly changing process variables. Use a protected input path, maintain a low-impedance reference for the output stage, and isolate the analog section from switching converters and high-current relays. The ADS1262IPW can serve as a companion when the measurement requires a high-resolution converter with integrated programmable gain and flexible excitation timing.

📊

Laboratory Data Acquisition

The INA111APG4 provides a practical input stage for laboratory instruments that measure small differential signals over a larger common-mode voltage. The device’s 500 µV maximum offset voltage and 5 µV/°C maximum offset drift establish important limits for DC accuracy, while its 2 MHz bandwidth supports faster measurements than a purely static precision amplifier. Designers should account for the front-end’s noise, input capacitance, gain error, and the acquisition system’s ADC characteristics. Keep the gain resistor compact and use a clean analog ground reference. The ADS8519IDB is a suitable companion when multiple channels require simultaneous sampling.

🎧

Audio and Analog Signal Conditioning

The INA111APG4 can serve as a differential input stage for balanced audio or other low-level analog signals when low input bias current and common-mode rejection are important. Its single-ended output simplifies connection to a downstream ADC or voltage-processing stage. The 2 MHz bandwidth is substantially above the audible band, allowing signal-chain filtering without relying on an extremely narrow-band device. However, offset voltage and noise must be included in the overall signal-to-noise calculation, and the input network must preserve channel balance. Use a shielded or tightly routed input path, a stable reference, and suitable output filtering before conversion.

What is the INA111APG4?
The INA111APG4 is a high-speed, FET-input instrumentation amplifier from Texas Instruments packaged in an 8-pin plastic DIP. According to the manufacturer datasheet, it uses a three-op-amplifier architecture, provides a listed 2 MHz bandwidth, and limits input bias current to 20 pA maximum. These characteristics make it suitable for high-impedance differential sensors, bridge circuits, and precision current measurements.
What are the key specifications of INA111APG4 that engineers should know?
The INA111APG4 combines a maximum input bias current of 20 pA, a maximum input offset voltage of 500 µV, a maximum offset drift of 5 µV/°C, a minimum common-mode rejection ratio of 106 dB, and a 2 MHz bandwidth. According to the Texas Instruments INA111 datasheet, these are the principal characteristics for determining compatibility with high-impedance sensors, bridge amplifiers, and precision analog acquisition circuits.
Where can I download the INA111APG4 datasheet PDF?
The official INA111 datasheet is available from Texas Instruments through the manufacturer link listed on this page. It describes the high-speed FET-input instrumentation amplifier, its electrical characteristics, gain configuration, typical application information, and ordering options. Use the manufacturer PDF for design decisions because distributor copies may not include every revision detail or package-specific table.
Where can I find the INA111APG4 pinout?
The INA111APG4 pinout is shown in the Texas Instruments INA111 manufacturer datasheet, along with the typical application and pin-configuration diagrams. The verified package designation for this orderable part is an 8-pin plastic DIP. Before assigning PCB tracks, use the pin-description table in the manufacturer datasheet and confirm the exact device revision associated with the ordering code.
Is the INA111APG4 suitable for high-impedance sensor measurements?
The INA111APG4 is suitable for many high-impedance sensor measurements because its input bias current is limited to 20 pA maximum. According to the manufacturer datasheet, the device also offers a minimum common-mode rejection ratio of 106 dB. The source impedance, sensor leakage, guarding, protection-network leakage, and required accuracy must still be evaluated together because low bias current alone does not guarantee complete system accuracy.
What is the bandwidth of the INA111APG4?
The INA111APG4 has a listed bandwidth of 2 MHz. According to the Texas Instruments INA111 datasheet, the usable signal bandwidth also depends on the selected closed-loop gain because higher gain normally reduces bandwidth. Designers should therefore check both gain and bandwidth conditions rather than treating 2 MHz as a gain-independent system limit, especially when driving an ADC.
What is the difference between INA111APG4 and INA111BU?
Both devices belong to the Texas Instruments INA111 family and use the same 8-pin plastic-DIP instrumentation-amplifier architecture, but their orderable suffixes identify different catalog variants. The verified technical distinction for INA111APG4 is its high-speed FET-input construction, 2 MHz bandwidth, 20 pA maximum bias current, 500 µV maximum offset voltage, and 106 dB minimum CMRR. Confirm temperature, packaging, and grade details against the manufacturer ordering table before substitution.
What is the difference between INA111APG4 and INA114APG4?
The INA114APG4 is a precision instrumentation amplifier, whereas the INA111APG4 is positioned as a high-speed FET-input instrumentation amplifier with a listed 2 MHz bandwidth. The INA114APG4 uses the same three-op-amplizer approach and an external gain-setting resistor, but its performance priorities and operating limits differ. The INA111APG4 is preferable when bandwidth and very low input bias current dominate the design.
When should I choose INA111APG4 over INA114APG4?
Choose the INA111APG4 when the application requires high-speed response or very low input bias current, using its listed 2 MHz bandwidth and 20 pA maximum bias current as the deciding criteria. Choose the INA114APG4 when precision-focused instrumentation-amplifier characteristics are more important than high-speed operation. Both can use an external resistor to establish gain, but their datasheet limits must be compared at the intended gain.
What can replace INA111APG4?
A valid replacement should preserve the 8-pin DIP footprint, pin assignment, power architecture, gain-setting method, and relevant electrical limits. The INA111BU is the closest same-family candidate identified for an eight-pin DIP configuration, while the INA114APG4 offers a closely related three-op-amplifier architecture with different performance priorities. Request a quote for the exact replacement MPN, and verify its manufacturer datasheet before approving a drop-in substitution.
Is INA111APG4 the same as INA114APG4?
No. The INA111APG4 and INA114APG4 are related instrumentation amplifiers but are not performance-identical devices. The INA111APG4 emphasizes high-speed operation and low bias current, with a listed 2 MHz bandwidth and 20 pA maximum bias current, while the INA114APG4 is described as a precision instrumentation amplifier. Treat them as alternatives requiring datasheet review, not automatic equivalents.
How do I design the gain network for INA111APG4?
The INA111 uses a three-op-amplifier architecture in which an external gain-setting resistor determines the differential gain. Use the gain equation, recommended resistor range, and permitted external resistance from the Texas Instruments INA111 datasheet. Place the gain resistor close to the designated pins, keep the two input paths symmetrical, and avoid adding excessive board leakage or capacitance that could upset gain accuracy and bandwidth.
What layout practices are important for INA111APG4?
Keep the gain resistor and input traces short, match the geometry of the differential input pair, and route sensitive nodes away from switching regulators, relays, and high-current return paths. The manufacturer application information should guide the reference and supply connections. For a bridge or current-shunt input, use guarding and a clean ground reference if leakage could otherwise create an error comparable to the sensor signal.
How much thermal dissipation does INA111APG4 produce?
Estimated: the INA111APG4 dissipation is approximately the supply voltage multiplied by the operating current, less the output-stage contribution; use the exact input voltage and quiescent-plus-load current from the selected operating condition. The Texas Instruments INA111 datasheet should be used for the final supply-current limit and thermal calculation because this part is supplied in a through-hole 8-pin plastic DIP rather than a thermally enhanced surface-mount package.
Where can I buy INA111APG4 and what is its lead time?
Use the Request a Quote form on this page to ask for INA111APG4 availability, current lead time, and minimum order quantity. The manufacturer identifies the INA111 as a high-speed FET-input instrumentation amplifier and the verified catalog listing identifies INA111APG4 as an 8-pin plastic-DIP device. Current inventory and delivery scheduling should be confirmed through the quote process before committing a production schedule.
Is INA111APG4 RoHS compliant?
Yes. The verified distributor catalog listing identifies INA111APG4 as RoHS compliant. According to the Texas Instruments product and datasheet information, the device is a high-speed FET-input instrumentation amplifier supplied in an 8-pin plastic DIP. For a complete environmental release, also review the current manufacturer material declaration or product-compliance documentation for the exact ordered part.

Справочные инженерные данные для INA111APG4 — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the INA111APG4 when the design needs a high-speed FET-input instrumentation amplifier, particularly when source impedance is high, the differential signal is small relative to its common-mode voltage, and the listed 2 MHz bandwidth provides a useful advantage. Its 20 pA maximum bias current and 106 dB minimum common-mode rejection make it especially suitable for bridge sensors, high-impedance probes, and precision shunt measurement. Select INA111BU when its specific ordering-grade characteristics meet the requirements more closely while preserving the same family architecture and eight-pin DIP format. Consider INA114APG4 when precision-focused instrumentation-amplifier performance is more important than the INA111's high-speed and low-bias-current positioning. For either related device, verify gain range, common-mode limits, output swing, supply range, temperature grade, and exact pin behavior against the manufacturer datasheet before approving a drop-in substitution.

Сравнение с аналогами

Параметр Этот товар INA111BU INA114APG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin plastic DIP 8-pin plastic DIP 8-pin plastic DIP
Device Type High-speed FET-input instrumentation amplifier INA111-family instrumentation amplifier Precision instrumentation amplifier
Internal Architecture 3-op-amplifier design 3-op-amplifier design 3-op-amplifier design

Ключевые отличия

  • Higher-bandwidth instrumentation-amplifier positioning (против INA114APG4)
  • Low-bias-current input stage (против INA114APG4)
  • Common-mode rejection suited to differential sensing (против INA114APG4)

Заметки по проектированию

Route the two input conductors as a matched pair and keep the external gain-setting resistor close to its designated pins. Place input protection components symmetrically so their leakage and capacitance do not unbalance the differential signal. Keep sensitive traces away from switching inductors, relay contacts, and high-current return paths. For high-impedance sources, reduce exposed PCB area and use guarding where its effect on leakage and capacitance has been evaluated.

Determine usable bandwidth at the selected closed-loop gain rather than relying only on the listed 2 MHz device bandwidth. Account for the gain-setting resistor’s parasitic capacitance, source capacitance, ADC input capacitance, and the bandwidth of the downstream filter. If the source is slow, added input capacitance can lengthen settling time; if it is fast, the input and output stages can limit system response. Use the manufacturer gain and application diagrams as the layout baseline.

Do not treat the 500 µV maximum input offset voltage as the only source of measurement error. Include offset drift, bias-current effects, gain error, resistor tolerance, ADC noise, and common-mode error in the uncertainty budget. Also verify the input common-mode range and output swing against the chosen supplies and reference voltage before assembly. These checks are essential when replacing INA111APG4 with INA114APG4 despite their common package and three-op-amplifier architecture.

Информация о соответствии

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The verified distributor catalog listing identifies INA111APG4 as RoHS compliant. No additional product-specific REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was established.

Данные проверены: 2026-11-19 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

INA111APG4 datasheet INA111APG4 pinout INA111APG4 datasheet pdf INA111APG4 equivalent INA111APG4 replacement INA111APG4 cross reference INA111APG4 vs INA114APG4 INA111APG4 8 pin DIP INA111APG4 application circuit INA111APG4 price INA111APG4 stock Texas Instruments INA111APG4 INA111APG4 2 MHz bandwidth INA111APG4 20 pA bias current INA111 bridge amplifier circuit

Связанные компоненты & термины

Texas Instruments INA111APG4 INA111BU INA114APG4 instrumentation amplifier high-speed FET-input instrumentation amplifier three-op-amplifier architecture analog signal conditioning input bias current input offset voltage offset-voltage drift common-mode rejection ratio CMRR 2 MHz bandwidth single-ended output 8-pin plastic DIP PDIP package through-hole package surface-mount bridge sensor strain-gauge amplifier high-impedance sensor current-shunt measurement precision ADC industrial process measurement
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ