INA111APG4 - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments
MPN: INA111APG4 ✓ فعالINA111APG4 نمای کلی
An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. Its internal three-op-amplifier architecture provides high input impedance and consistent gain-setting behavior. This places the INA111 in the amplifier hierarchy of analog ICs and instrumentation amplifiers, where it supports sensor interfaces, bridge amplifiers, current measurement, and laboratory acquisition systems without requiring a separate input-buffer stage.
Principal features include a maximum input bias current of 20 pA, a maximum input offset voltage of 500 µV, a maximum offset-voltage drift of 5 µV/°C, and a minimum common-mode rejection ratio of 106 dB. The device also provides high-speed operation with a listed 2 MHz bandwidth. These characteristics make it especially useful when the source presents very high impedance, when small differential signals must be measured in the presence of a much larger common-mode voltage, or when measurement bandwidth must exceed that of a general-purpose precision amplifier.
The INA111 uses a three-amplifier instrumentation-amplifier architecture. Its FET input stage limits input bias current, while the differential signal is amplified according to an external gain-setting resistor. The listed 106 dB minimum common-mode rejection helps suppress common-mode voltage in industrial sensor systems, while the 2 MHz bandwidth allows the device to process signals beyond the static-measurement range associated with many precision op amps. Its single-ended output is intended for use with external analog-to-digital converters, filters, and downstream acquisition circuitry.
Typical applications include low-current sensor conditioning, strain-gauge and resistance-bridge measurement, precision current sensing, high-impedance laboratory probes, and industrial process-monitoring inputs. In a bridge circuit, the amplifier converts a small differential bridge excitation into a larger single-ended voltage. In a current-shunt system, its low bias current minimizes measurement error from high-resistance sense lines, while the high common-mode rejection helps preserve accuracy when the shunt signal is superimposed on a larger supply voltage.
Design should preserve the distinction between input bias current, input offset voltage, and the common-mode voltage range. Place the gain-setting resistor close to the appropriate device pins, route sensitive input traces away from switching nodes and power-converter currents, and use a suitable reference arrangement when the output must remain centered in a unipolar converter range. Verify bandwidth, output-swing limits, supply headroom, and input protection against the actual sensor and ADC requirements.
This page combines manufacturer specifications, package and ordering information, comparison parameters, and practical circuit-design guidance for engineers evaluating the INA111APG4 as a high-speed FET-input instrumentation amplifier.
جایگزینهای drop-in برای INA111APG4 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای INA111APG4 (همان فرمفاکتور و فوتپرینت) — متفاوت در Common-Mode Rejection Ratio, Input Bias Current, Mounting Type, Package.
INA111BU
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←INA114APG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
INA111APG4 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Instrumentation amplifier |
| Number of Amplifier Circuits | 1 circuit |
| Internal Architecture | 3-op-amplifier design |
| Input Bias Current | 20 pA maximum |
| Input Offset Voltage | 500 µV maximum |
| Input Offset Voltage Drift | 5 µV/°C maximum |
| Common-Mode Rejection Ratio | 106 dB minimum |
| Bandwidth | 2 MHz |
| نوع خروجی | Single-ended |
| بستهبندی | 8-pin plastic DIP |
| نوع نصب | Through-hole |
| وضعیت RoHS | RoHS compliant |
راهنمای پیکربندی پین INA111APG4 8-pin plastic dip
پیکربندی پین برای INA111APG4 (پکیج 8-pin plastic dip). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای INA111APG4.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
INA111APG4 مناسب است برای 6 کاربردs: Precision Bridge Sensor Conditioning, High-Impedance Probe Amplification, Low-Current Shunt Measurement, Industrial Process Measurement, Laboratory Data Acquisition, Audio and Analog Signal Conditioning.
Precision Bridge Sensor Conditioning
The INA111APG4 is well suited to strain-gauge, load-cell, and resistive-bridge measurement because its 20 pA maximum input bias current limits the error introduced by high source impedance. Its 106 dB minimum common-mode rejection helps isolate the small differential bridge signal from excitation-related common-mode voltage. Place the device close to the bridge, route the two signal inputs symmetrically, and use the external gain-setting resistor to establish the required sensitivity. The 2 MHz bandwidth also leaves headroom for mechanical resonances and filtering above the primary measurement bandwidth. A suitable companion is the ADS1262IPW when a high-resolution converter is required.
پیشنهادی
High-Impedance Probe Amplification
The INA111APG4 can amplify signals from electrochemical, capacitive, or laboratory probes whose source impedance is high enough that input bias current matters. The listed maximum input bias current of 20 pA helps preserve sensor fidelity, while the minimum common-mode rejection ratio of 106 dB supports systems in which the common-mode voltage is much larger than the signal of interest. For practical layouts, minimize exposed trace area, use guarding where leakage can affect the measurement, and keep input capacitance low to preserve response. The device’s 2 MHz bandwidth makes it appropriate when the measurement includes content beyond static DC.
پیشنهادی
Low-Current Shunt Measurement
For low-current power monitoring, the INA111APG4 can amplify the differential voltage across a shunt while rejecting the supply-related common-mode voltage. Its 20 pA maximum input bias current is particularly helpful when using long, high-impedance sense connections that could otherwise introduce error. The common-mode rejection ratio of at least 106 dB supports accurate extraction of a relatively small shunt signal. Keep the Kelvin sense traces paired and away from high-current switching paths, and check the shunt’s power dissipation separately from the amplifier’s operating limits. The INA240A4DR is a useful alternative when the design requires a dedicated bidirectional current-sensing amplifier instead.
پیشنهادی
Industrial Process Measurement
The INA111APG4 is applicable to industrial process signals that arrive as small differential voltages over substantial common-mode voltage. Its 106 dB minimum common-mode rejection supports reliable extraction of sensor information in electrically noisy equipment, while the high-speed response can accommodate rapidly changing process variables. Use a protected input path, maintain a low-impedance reference for the output stage, and isolate the analog section from switching converters and high-current relays. The ADS1262IPW can serve as a companion when the measurement requires a high-resolution converter with integrated programmable gain and flexible excitation timing.
پیشنهادی
Laboratory Data Acquisition
The INA111APG4 provides a practical input stage for laboratory instruments that measure small differential signals over a larger common-mode voltage. The device’s 500 µV maximum offset voltage and 5 µV/°C maximum offset drift establish important limits for DC accuracy, while its 2 MHz bandwidth supports faster measurements than a purely static precision amplifier. Designers should account for the front-end’s noise, input capacitance, gain error, and the acquisition system’s ADC characteristics. Keep the gain resistor compact and use a clean analog ground reference. The ADS8519IDB is a suitable companion when multiple channels require simultaneous sampling.
پیشنهادی
Audio and Analog Signal Conditioning
The INA111APG4 can serve as a differential input stage for balanced audio or other low-level analog signals when low input bias current and common-mode rejection are important. Its single-ended output simplifies connection to a downstream ADC or voltage-processing stage. The 2 MHz bandwidth is substantially above the audible band, allowing signal-chain filtering without relying on an extremely narrow-band device. However, offset voltage and noise must be included in the overall signal-to-noise calculation, and the input network must preserve channel balance. Use a shielded or tightly routed input path, a stable reference, and suitable output filtering before conversion.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای INA111APG4 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | INA111BU | INA114APG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin plastic DIP | 8-pin plastic DIP | 8-pin plastic DIP |
| Device Type | High-speed FET-input instrumentation amplifier | INA111-family instrumentation amplifier | Precision instrumentation amplifier |
| Internal Architecture | 3-op-amplifier design | 3-op-amplifier design | 3-op-amplifier design |
تفاوتهای کلیدی
- Higher-bandwidth instrumentation-amplifier positioning (در مقابلINA114APG4)
- Low-bias-current input stage (در مقابلINA114APG4)
- Common-mode rejection suited to differential sensing (در مقابلINA114APG4)
یادداشتهای طراحی
Route the two input conductors as a matched pair and keep the external gain-setting resistor close to its designated pins. Place input protection components symmetrically so their leakage and capacitance do not unbalance the differential signal. Keep sensitive traces away from switching inductors, relay contacts, and high-current return paths. For high-impedance sources, reduce exposed PCB area and use guarding where its effect on leakage and capacitance has been evaluated.
Determine usable bandwidth at the selected closed-loop gain rather than relying only on the listed 2 MHz device bandwidth. Account for the gain-setting resistor’s parasitic capacitance, source capacitance, ADC input capacitance, and the bandwidth of the downstream filter. If the source is slow, added input capacitance can lengthen settling time; if it is fast, the input and output stages can limit system response. Use the manufacturer gain and application diagrams as the layout baseline.
Do not treat the 500 µV maximum input offset voltage as the only source of measurement error. Include offset drift, bias-current effects, gain error, resistor tolerance, ADC noise, and common-mode error in the uncertainty budget. Also verify the input common-mode range and output swing against the chosen supplies and reference voltage before assembly. These checks are essential when replacing INA111APG4 with INA114APG4 despite their common package and three-op-amplifier architecture.
اطلاعات انطباق
The verified distributor catalog listing identifies INA111APG4 as RoHS compliant. No additional product-specific REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was established.