ISL8323IBZ - 60 ohm Dual SPST Analog Switch | Renesas
Артикул: ISL8323IBZ ✗ Снят с производстваISL8323IBZ Обзор
An analog switch is a semiconductor-based interface device that routes low-frequency analog signals between circuit nodes under digital control. The ISL8323 belongs to the analog-switch and multiplexer hierarchy within interface ICs, with the ISL8323IBZ providing two independent SPST paths rather than a shared multiplexer structure. Its normally open configuration leaves each switch disconnected until the corresponding control input activates it.
Key characteristics include 60 ohm on resistance, 100 pA maximum leakage, 5 uW power consumption, 5 pC maximum charge injection, and 9 pF maximum channel capacitance. The operating temperature range extends from -40 C to +85 C. These specifications make the device appropriate where low leakage, low power, and compact signal isolation matter more than ultra-low resistance or very high switching speed.
The ISL8323 family is designed for single-supply operation between 2.7 V and 12 V. Each independent switch can be controlled separately, allowing two signals to be routed, isolated, sampled, or connected to a shared analog resource. The 5 pC maximum charge injection limits control-transition disturbance at sensitive input nodes, while 9 pF capacitance helps preserve bandwidth in moderate-impedance circuits.
Typical uses include battery-powered measurement systems, portable medical and industrial equipment, analog test circuits, signal isolation between amplifiers and data converters, and low-leakage sensor interfaces. The low 5 uW power figure is particularly useful in equipment where standby consumption must remain small. Because the on resistance is 60 ohms, the switch is most suitable for sensor, control, and instrumentation signals rather than high-current or low-impedance RF paths.
Designers should verify signal amplitude, leakage-driven error, control-logic levels, and bandwidth before committing the device to a precision circuit. The SOIC footprint simplifies assembly, but unused control inputs and switch terminals must be connected according to the manufacturer pin-description table. Input voltages must remain within the specified supply range, and analog signals should not exceed the device's allowed voltage limits.
This page organizes the verified electrical characteristics, lifecycle status, sourcing information, pin-access guidance, and application-specific design considerations for engineers evaluating the ISL8323IBZ. It also distinguishes true pin-compatible alternatives from nearby family members that use different switch configurations, helping prevent footprint-compatible but electrically unsuitable substitutions.
Аналоги без доработки для ISL8323IBZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL8323IBZ (тот же форм-фактор и посадочное место) — отличается по Package, Switch Configuration, Number of Circuits, On Resistance.
ISL8323IB
✅ Прямая заменаУточнить цену
Открыть даташит →ISL83072EIBZA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8323IBZ Максимальные параметры и электрические характеристики
| Number of Switches | 2 |
| Switch Configuration | 2 x SPST, normally open |
| On Resistance | 60 ohm typical |
| Supply Voltage Range | +2.7 V to +12 V |
| Power Consumption | 5 uW |
| Off Leakage Current | 100 pA maximum |
| Charge Injection | 5 pC maximum per channel |
| Channel Capacitance | 9 pF maximum |
| Off Crosstalk | -85 dB at 1 MHz |
| Диапазон рабочих температур | -40 C to +85 C |
| Корпус | 8-SOIC, 3.90 mm width |
| Тип монтажа | Surface mount |
| Supply Type | Single supply |
| Switch Type | Normally open |
| Статус RoHS | unknown |
| REACH Status | unknown |
Руководство по цоколевке ISL8323IBZ в корпусе 8-soic, 3.90 mm width
Цоколевка для ISL8323IBZ (корпус 8-soic, 3.90 mm width). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ISL8323IBZ.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ISL8323IBZ подходит для 6 применениеs: Battery-Powered Sensor Signal Routing, Portable Medical Signal Isolation, Data Converter Input Routing, Industrial Control Signal Isolation, Audio and Low-Frequency Signal Switching, Automated Test and Measurement.
Battery-Powered Sensor Signal Routing
The ISL8323IBZ fits battery-powered sensor interfaces because it operates from a single +2.7 V to +12 V supply and has a stated power consumption of 5 uW. Place one normally open switch between the sensor output and the measurement amplifier when the sensor must be disconnected during idle periods. The maximum 100 pA off leakage helps reduce errors on high-impedance sensor nodes, although the complete error budget must also include amplifier input bias current, protection-device leakage, and PCB contamination. The 60 ohm on resistance should be checked against the amplifier input impedance and settling requirements.
Рекомендуется
Portable Medical Signal Isolation
The ISL8323IBZ can isolate sensitive analog paths in portable medical and monitoring equipment while operating from a low-voltage single supply. Its two independent normally open switches can disconnect patient-connected or measurement channels during idle periods, and the 5 pC maximum charge injection limits control-transition disturbance at sensitive inputs. The -40 C to +85 C operating range supports industrial and medical equipment environments where qualification is appropriate. Design validation should still account for switch resistance, leakage, electrode protection components, applicable medical standards, and the complete system isolation architecture.
Рекомендуется
Data Converter Input Routing
The ISL8323IBZ can route two analog signals into a shared data-converter input in test and measurement systems. Each normally open path provides independent control, while the 9 pF maximum channel capacitance and -85 dB off crosstalk at 1 MHz help limit coupling between the selected and inactive route. The 60 ohm on resistance is suitable for moderate-impedance acquisition networks but may not be adequate for very low-impedance converter inputs. Confirm settling time, source impedance, acquisition bandwidth, and sampling-control timing against the converter requirements.
Рекомендуется
Industrial Control Signal Isolation
The ISL8323IBZ is useful for isolating control, feedback, or diagnostic signals in industrial equipment. Its +2.7 V to +12 V supply range and 5 uW power consumption suit compact low-power control boards, while the two independent SPST channels provide separate routing paths. The maximum 100 pA off leakage is valuable when the connected circuit has high source impedance, and the 5 pC charge-injection limit supports relatively quiet transitions. Qualification must cover the full industrial temperature range, transient levels, grounding strategy, and protection requirements at externally accessible nodes.
Рекомендуется
Audio and Low-Frequency Signal Switching
The ISL8323IBZ can switch low-frequency audio or instrumentation signals when low leakage and low control-transition disturbance are more important than very low on resistance. Its two normally open paths allow a signal to be selected or disconnected without changing the default system routing. The 60 ohm on resistance can create measurable insertion loss when driving a low-impedance load, so the amplifier output impedance and load must be checked before use. The 9 pF channel capacitance is modest for many audio-rate circuits, but cable capacitance and long PCB routes can add substantial loading.
Рекомендуется
Automated Test and Measurement
The ISL8323IBZ fits automated test systems that need controlled connection of low-level analog probes. Two independent normally open switches can route a DUT node to different measurement paths or isolate it between tests. Its 60 ohm resistance, 100 pA leakage, and -85 dB off crosstalk at 1 MHz provide defined behavior for many medium-impedance fixtures. Engineers should include fixture and cable impedance in error calculations, use short guarded routes, and verify that the selected switch timing meets the test-system settling requirements.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ISL8323IBZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL8323IB | ISL83072EIBZA |
|---|---|---|---|
| Package | 8-SOIC, 3.90 mm width | 8-SOIC - same package | 8-SOIC - same package |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Switch Configuration | 2 x SPST, normally open | 2 x SPST, normally open | Dual SPST |
Ключевые отличия
- Documented two-channel normally open behavior (против ISL8324IBZ and ISL8325IBZ)
- Very low off leakage for high-impedance routing (против ISL83072EIBZA)
- Low-power operation for portable systems (против ISL8323IB)
Заметки по проектированию
Treat the 60 ohm on resistance as part of the signal-path impedance. For a source resistance of Rs, the closed switch forms an additional resistive divider with the load. Keep traces short, use a high-impedance receiver where appropriate, and verify the resulting attenuation and noise contribution. The 9 pF maximum channel capacitance should also be included when assessing high-frequency roll-off, especially with connector and cable capacitance.
Do not substitute the ISL8324 or ISL8325 merely because they use a related 8-SOIC package. The ISL8323 provides two normally open switches, whereas the ISL8324 provides normally closed switches and the ISL8325 mixes one normally open and one normally closed path. Such a substitution changes the default connection state and can create incorrect or unsafe system behavior even when the footprint appears identical.
Use the manufacturer pin-description table to assign every control, supply, common, and normally open terminal before routing the PCB. Keep the analog signal traces away from control-clock edges and fast digital nets to reduce coupled disturbance. A solid ground plane, short return paths, and clean board assembly practices are particularly important when the switched node has high impedance, because leakage and contamination can degrade accuracy more than the nominal 100 pA limit.
The specified 5 uW power consumption is suitable for low-power designs, but it should not be treated as the complete system power budget. Include control-driver current, pull resistors, leakage, and the power consumed by connected analog circuits. Decouple the single supply close to the device with the capacitance recommended by the manufacturer, and ensure the control signals remain within valid logic thresholds across the full supply-voltage range.
Информация о соответствии
No explicit compliance declaration for the exact ISL8323IBZ orderable appears in the cited manufacturer material. Obtain current declarations from Renesas before production release. The device is an analog interface IC and is not identified as an AEC-Q100-qualified automotive part.