ISL8489EIB - 5V Full-Duplex RS-485 Transceiver | Renesas
Артикул: ISL8489EIB ✓ АктивенISL8489EIB Обзор
An RS-485 transceiver is an interface IC that converts logic-level signals into differential RS-485 or RS-422 transmissions and converts received differential signals into logic-level data. The ISL8489EIB supports both standards because its balanced driver and receiver architecture meets the signaling requirements of half-duplex multidrop RS-485 networks and full-duplex point-to-point RS-422 systems. The device belongs to the interface-IC hierarchy and supports bidirectional communication between controllers, sensors, industrial equipment, and field buses.
Key features include one transmit driver, one receive receiver, full-duplex operation, 5 V operation, and a maximum data rate of 250 kbps. Its 15 kV ESD protection improves robustness against electrostatic discharge encountered during industrial installation and servicing. The -40°C to +85°C temperature range covers extended industrial environments, while the 14-pin SOIC package supports conventional surface-mount assembly and automated inspection.
The BiCMOS implementation combines bipolar and CMOS characteristics, supporting low-power 5 V operation while providing the drive and receive performance required for balanced communication. Full duplex allows the driver and receiver to operate simultaneously, which is useful when transmit and receive paths must remain active. Its 250 kbps maximum rate is appropriate for industrial control buses, instrumentation links, and equipment interfaces that do not require high-speed differential data protocols.
Typical applications include industrial automation controllers, RS-485 sensor gateways, motor-control equipment, building-automation nodes, and point-to-point RS-422 links between distributed modules. In a multidrop RS-485 network, the transceiver interfaces a microcontroller UART to a balanced bus while the system supplies termination and biasing components. In a full-duplex implementation, separate differential pairs provide independent transmit and receive paths.
PCB design should preserve the balanced trace geometry of the bus and route driver and receiver outputs away from sensitive analog inputs. Place the transceiver close to the board connector to minimize exposed ESD paths, and use the package pin-description table in the manufacturer datasheet when assigning connector and protection-circuitry connections. The 15 kV ESD rating describes the specified protection level, not a guarantee that external surge or lightning protection is unnecessary.
This page combines device specifications, verified package and ordering information, application guidance, and same-family drop-in alternatives. It also identifies the electrical details that engineers should confirm against the manufacturer datasheet when qualifying a new RS-422 or RS-485 design.
Аналоги без доработки для ISL8489EIB — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL8489EIB (тот же форм-фактор и посадочное место) — отличается по ESD Protection, Package, Manufacturer, Product Type, Slew Rate.
ISL8488EIB
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →ISL8489EIBZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8490EIB
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ISL8491EIB
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →ISL8489EIBZ-T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8489EIB Характеристики
| Product Type | RS-422/RS-485 transceiver |
| Напряжение питания | 5 V |
| Operating Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Duplex Mode | Full duplex |
| Supported Standards | RS-422 and RS-485 |
| ESD Protection | 15 kV |
| Диапазон рабочих температур | -40°C to +85°C |
| Корпус | 14-pin SOIC |
| Тип монтажа | Surface mount |
| Process Technology | BiCMOS |
| Slew Rate | Limited |
| Power Classification | Low power |
Руководство по цоколевке ISL8489EIB в корпусе 14-pin soic
Цоколевка для ISL8489EIB (корпус 14-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ISL8489EIB.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ISL8489EIB подходит для 6 применениеs: Industrial Automation Controller, RS-485 Sensor Gateway, Building Automation Node, Point-to-Point RS-422 Link, Motor and Drive Control Interface, Instrumentation and Test Equipment.
Industrial Automation Controller
The ISL8489EIB suits industrial automation equipment that exchanges controller commands with remote sensors, actuators, or drive modules over a balanced bus. Its 5 V supply operation, 250 kbps maximum data rate, and -40°C to +85°C rating align with factory-control environments where a UART must connect to an RS-485 physical layer. The full-duplex configuration also permits simultaneous transmit and receive activity in systems using separate differential pairs. Place the transceiver near the field connector, maintain matched bus geometry, and apply termination and biasing according to the network topology.
Рекомендуется
RS-485 Sensor Gateway
The ISL8489EIB can bridge a 5 V controller to an RS-485 sensor network when the required bus rate is 250 kbps or lower. Its one-driver/one-receiver arrangement is appropriate for a compact gateway with one physical communication channel, while full-duplex operation supports designs that separate transmit and receive conductors. The 15 kV ESD protection is useful near field wiring, although the gateway also needs connector placement and external protection suited to its installation environment. Confirm bus length, node count, termination, and grounding before deploying the interface.
Рекомендуется
Building Automation Node
The ISL8489EIB provides a balanced bus interface for building-automation nodes that exchange sensor readings, occupancy commands, or equipment status with a central controller. Its 4.5 V to 5.5 V operating range fits regulated 5 V electronics, and the 250 kbps rate is adequate for common low-speed building-control traffic. The -40°C to +85°C range supports equipment rooms and industrial-style control cabinets. Designers should use common-mode grounding, surge protection, and cable routing appropriate to the building's wiring environment rather than treating ESD protection as a complete surge solution.
Рекомендуется
Point-to-Point RS-422 Link
The ISL8489EIB is appropriate for a point-to-point RS-422 connection when a 5 V system needs full-duplex data transfer between two pieces of equipment. Its one driver and one receiver support separate balanced transmit and receive paths, while the maximum 250 kbps rate covers many control, monitoring, and instrumentation links. The integrated 15 kV ESD protection strengthens the interface near equipment connectors. Confirm receiver sensitivity, cable length, termination strategy, and signal polarity against the manufacturer datasheet before approving the link for a new system.
Рекомендуется
Motor and Drive Control Interface
The ISL8489EIB can connect a control board to motor-drive or positioning equipment that uses an RS-422 or RS-485 command interface. The full-duplex arrangement is useful where motion-control feedback must coexist with command transmission, and the 250 kbps rate is suitable for many configuration and status channels. Industrial temperature operation supports controlled drive cabinets, while 15 kV ESD protection adds robustness at the interface boundary. Use isolation, shielding, or additional surge protection when the motor environment exceeds the transceiver's specified ESD conditions.
Рекомендуется
Instrumentation and Test Equipment
The ISL8489EIB supports laboratory and industrial instrumentation that needs a reliable balanced communications interface between a controller and remote measurement hardware. Its 250 kbps maximum data rate is suitable for many command, status, and slow-measurement channels, while full-duplex operation simplifies simultaneous control and data transfer. The 5 V supply and 14-pin SOIC package allow integration with conventional test-equipment boards. Use controlled grounding and short, balanced interconnects to minimize noise and susceptibility to common-mode interference in precision measurement systems.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ISL8489EIB — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL8488EIB | ISL8489EIBZ | ISL8490EIB | ISL8491EIB |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 |
| Process Technology | BiCMOS | BiCMOS | BiCMOS | BiCMOS | BiCMOS |
| Ordering Form | ISL8489EIB | ISL8488EIB | ISL8489EIBZ | ISL8490EIB | ISL8491EIB |
Ключевые отличия
- Exact same-family ordering option with matching core ratings (против ISL8489EIBZ)
- Full-duplex balanced communication in a compact 14-pin package (против ISL8488EIB)
- Industrial temperature and ESD protection (против ISL8490EIB)
Заметки по проектированию
Place the ISL8489EIB close to the external communication connector so the protected transceiver pins connect to the cable interface through a short, controlled path. Route the RS-422 or RS-485 traces as a balanced pair with matching geometry and a continuous reference plane. Keep the connector-side protection network close to the entry point, and maintain separation between transceiver routing and unrelated clock, sensor, and power-converter paths.
Use the exact pin-description table in the manufacturer datasheet to assign driver, receiver, enable, ground, and supply connections. The device is a full-duplex 1/1 transceiver in a 14-pin SOIC, but family ordering variants can have different control behavior. Decouple the 5 V supply locally, connect the ground pins according to the package drawing, and test both transmit and receive directions independently after assembly.
Do not treat the specified 15 kV ESD protection as complete lightning or industrial surge protection. Determine the installation threat, then add connector-level surge and common-mode protection where required. Also avoid assuming that every RS-485 network requires the same termination and bias arrangement: full-duplex systems generally use separate transmit and receive pairs, while multidrop topology determines where termination and fail-safe biasing are installed.
Информация о соответствии
The device is listed as an industrial-temperature 5 V transceiver, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact MPN. Check the current manufacturer product declaration and applicable customer requirements before procurement.