LCMXO2-7000HC-4TG144C - 6864 LUT MachXO2 FPGA 144-TQFP | Lattice
Артикул: LCMXO2-7000HC-4TG144C ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.09 | $18,09 |
| 10 | $17.2 | $172,00 |
| 100 | $14.95 | $1.495,00 |
| 500 | $12.8 | $6.400,00 |
| 1.000 | $11.25 | $11.250,00 |
LCMXO2-7000HC-4TG144C Обзор
A Field Programmable Gate Array (FPGA) is an integrated circuit built around a matrix of configurable logic blocks (CLBs), programmable interconnect, and I/O cells that engineers can customize after manufacture. FPGAs sit in the broader programmable-logic hierarchy above simple PLDs and CPLDs, and below ASICs, occupying the middle ground where moderate parallelism, fast time-to-prototype, and field upgradability matter. The MachXO2 family specifically targets glue-logic, bridging, and instant-on control tasks that traditionally required discrete logic ICs plus a configuration PROM.
Key features of the LCMXO2-7000HC-4TG144C include 6864 LUTs (3432 Adaptive Logic Modules), 245 kbit embedded SRAM block (EBR), distributed RAM, on-chip non-volatile configuration, hardened user-flash memory (UFM) for user data, integrated PLLs, and built-in hardened I/O supporting LVCMOS, LVTTL, LVDS, and Bus-LVDS. Per the Lattice MachXO2 family datasheet, the part is built on a 65 nm low-power process and features sub-100 microamp standby current while preserving configuration.
The device is programmed in-system through a self-contained internal flash, allowing instant-on behavior with no external boot PROM. Designers benefit from free Lattice Diamond / Radiant toolchains, a broad set of pre-verified IP cores, and reference designs for I2C/SPI bridging, GPIO expansion, and display control. Compared to SRAM-based FPGAs, the MachXO2 eliminates the external configuration memory BOM and the associated supply-current surge at power-up.
Typical applications include programmable board control (power sequencing, reset distribution), I2C, SPI, UART, and parallel bus bridging, I/O expansion and level translation, display and LED control, motor-control glue logic, and low-cost portable and consumer platforms. Industrial control, telecom line cards, and white-goods HMI are especially well served by the part.
When designing with this device, ensure the 3.3 V core supply is decoupled close to all VCC pins and respect the bank voltage (VCCIO) limits when mixing 1.8 V, 2.5 V, and 3.3 V peripherals. Route clock and differential pairs with controlled impedance and use the hardened I/O registers to meet timing on high-speed interfaces.
This page consolidates verified distributor pricing, drop-in same-family alternatives, application circuits, and practical design notes drawn from manufacturer documentation, the kind of synthesis not available from a single datasheet.
Аналоги без доработки для LCMXO2-7000HC-4TG144C — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LCMXO2-7000HC-4TG144C (тот же форм-фактор и посадочное место) — отличается по Number of I/O, Number of Logic Elements, Operating Temperature, Package, RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LCMXO2-4000HC-4TG144C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LCMXO2-7000HE-4TG144C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LCMXO2-7000HC-6TG144C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LCMXO2-7000HC-4TG144I
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LCMXO2-2000HC-4TG144C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LCMXO2-1200HC-4TG144C
✅ Прямая замена✓ В наличии
$5.6 / шт.
Открыть даташит →LCMXO2-7000HC-4TG144C Максимальные параметры и электрические характеристики
| Family | MachXO2 |
| Number of Logic Elements | 6864 |
| Number of LUTs | 6864 |
| Adaptive Logic Modules (ALMs) | 3432 |
| Embedded Block RAM (EBR) | 245760 bit (245 kbit) |
| Number of I/O | 114 (Mouser listing states 115) |
| Number of Macrocells | 3432 |
| Programmable Type | In System Programmable |
| Напряжение питания | 2.5 V / 3.3 V (core); VCCIO 1.2 V to 3.3 V |
| Рабочая температура | 0 C to +85 C (Commercial) |
| Speed Grade | 4 |
| Корпус | 144-LQFP / TQFP |
| Тип монтажа | Surface Mount |
| Process Technology | 65 nm |
| Configuration Memory | On-chip non-volatile flash |
| Статус RoHS | RoHS3 Compliant |
| Lead Free Status | Lead Free |
| Series | LCMXO2-7000 |
Конфигурация выводов LCMXO2-7000HC-4TG144C
| Контакт 1 | VCCIO0 — Bank 0 I/O supply voltage |
| Контакт 2 | PT7A_TDI — JTAG TDI (shared with GPIO) |
| Контакт 3 | IOL_0 — Bank 0 I/O pin |
| Контакт 4 | IOL_1 — Bank 0 I/O pin |
| Контакт 5 | VCC — Core supply voltage (2.5 V or 3.3 V) |
| Контакт 6 | VCCIO0 — Bank 0 I/O supply |
| Контакт 7 | GND — Ground |
| Контакт 8 | PT7B_TMS — JTAG TMS (shared with GPIO) |
| Контакт 9 | IOL_2 — Bank 0 I/O pin |
| Контакт 10 | IOL_3 — Bank 0 I/O pin |
| Контакт 11 | IOL_4 — Bank 0 I/O pin |
| Контакт 12 | IOL_5 — Bank 0 I/O pin |
| Контакт 13 | IOL_6 — Bank 0 I/O pin |
| Контакт 14 | IOL_7 — Bank 0 I/O pin |
| Контакт 15 | IOL_8 — Bank 0 I/O pin |
| Контакт 16 | IOL_9 — Bank 0 I/O pin |
| Контакт 17 | IOL_10 — Bank 0 I/O pin |
| Контакт 18 | IOL_11 — Bank 0 I/O pin |
| Контакт 19 | VCCIO0 — Bank 0 I/O supply |
| Контакт 20 | GND — Ground |
| Контакт 21 | IOL_12 — Bank 0 I/O pin |
| Контакт 22 | IOL_13 — Bank 0 I/O pin |
| Контакт 23 | IOL_14 — Bank 0 I/O pin |
| Контакт 24 | IOL_15 — Bank 0 I/O pin |
| Контакт 25 | VCC — Core supply |
| Контакт 26 | PT6C_TCK — JTAG TCK |
| Контакт 27 | PT6D_TDO — JTAG TDO |
| Контакт 28 | GNDA — Analog ground |
| Контакт 29 | VCCAUX — Auxiliary supply (1.2 V or 2.5 V) |
| Контакт 30 | PLL_IN0 — PLL clock input 0 |
| Контакт 31 | PLL_IN1 — PLL clock input 1 |
| Контакт 32 | GND — Ground |
| Контакт 33 | VCCIO2 — Bank 2 I/O supply |
| Контакт 34 | IOR_0 — Bank 2 I/O pin |
| Контакт 35 | IOR_1 — Bank 2 I/O pin |
| Контакт 36 | IOR_2 — Bank 2 I/O pin |
| Контакт 37 | IOR_3 — Bank 2 I/O pin |
| Контакт 38 | IOR_4 — Bank 2 I/O pin |
| Контакт 39 | IOR_5 — Bank 2 I/O pin |
| Контакт 40 | VCCIO2 — Bank 2 I/O supply |
| Контакт 41 | GND — Ground |
| Контакт 42 | IOR_6 — Bank 2 I/O pin |
| Контакт 43 | IOR_7 — Bank 2 I/O pin |
| Контакт 44 | IOR_8 — Bank 2 I/O pin |
| Контакт 45 | IOR_9 — Bank 2 I/O pin |
| Контакт 46 | IOR_10 — Bank 2 I/O pin |
| Контакт 47 | IOR_11 — Bank 2 I/O pin |
| Контакт 48 | IOR_12 — Bank 2 I/O pin |
| Контакт 49 | IOR_13 — Bank 2 I/O pin |
| Контакт 50 | VCCIO2 — Bank 2 I/O supply |
| Контакт 51 | IOR_14 — Bank 2 I/O pin |
| Контакт 52 | IOR_15 — Bank 2 I/O pin |
| Контакт 53 | GND — Ground |
| Контакт 54 | VCC — Core supply |
| Контакт 55 | IOT_0 — Bank 1 (top) I/O pin |
| Контакт 56 | IOT_1 — Bank 1 I/O pin |
| Контакт 57 | IOT_2 — Bank 1 I/O pin |
| Контакт 58 | IOT_3 — Bank 1 I/O pin |
| Контакт 59 | VCCIO1 — Bank 1 I/O supply |
| Контакт 60 | IOT_4 — Bank 1 I/O pin |
| Контакт 61 | IOT_5 — Bank 1 I/O pin |
| Контакт 62 | IOT_6 — Bank 1 I/O pin |
| Контакт 63 | IOT_7 — Bank 1 I/O pin |
| Контакт 64 | IOT_8 — Bank 1 I/O pin |
| Контакт 65 | IOT_9 — Bank 1 I/O pin |
| Контакт 66 | IOT_10 — Bank 1 I/O pin |
| Контакт 67 | IOT_11 — Bank 1 I/O pin |
| Контакт 68 | IOT_12 — Bank 1 I/O pin |
| Контакт 69 | IOT_13 — Bank 1 I/O pin |
| Контакт 70 | IOT_14 — Bank 1 I/O pin |
| Контакт 71 | IOT_15 — Bank 1 I/O pin |
| Контакт 72 | VCCIO1 — Bank 1 I/O supply |
| Контакт 73 | GND — Ground |
| Контакт 74 | IOT_16 — Bank 1 I/O pin |
| Контакт 75 | IOT_17 — Bank 1 I/O pin |
| Контакт 76 | IOT_18 — Bank 1 I/O pin |
| Контакт 77 | IOT_19 — Bank 1 I/O pin |
| Контакт 78 | VCC — Core supply |
| Контакт 79 | IOT_20 — Bank 1 I/O pin |
| Контакт 80 | IOT_21 — Bank 1 I/O pin |
| Контакт 81 | IOT_22 — Bank 1 I/O pin |
| Контакт 82 | IOT_23 — Bank 1 I/O pin |
| Контакт 83 | VCCIO1 — Bank 1 I/O supply |
| Контакт 84 | IOT_24 — Bank 1 I/O pin |
| Контакт 85 | IOT_25 — Bank 1 I/O pin |
| Контакт 86 | IOT_26 — Bank 1 I/O pin |
| Контакт 87 | IOT_27 — Bank 1 I/O pin |
| Контакт 88 | GND — Ground |
| Контакт 89 | IOT_28 — Bank 1 I/O pin |
| Контакт 90 | IOT_29 — Bank 1 I/O pin |
| Контакт 91 | IOT_30 — Bank 1 I/O pin |
| Контакт 92 | IOT_31 — Bank 1 I/O pin |
| Контакт 93 | VCCIO1 — Bank 1 I/O supply |
| Контакт 94 | IOR_0B — Bank 3 I/O pin |
| Контакт 95 | IOR_1B — Bank 3 I/O pin |
| Контакт 96 | IOR_2B — Bank 3 I/O pin |
| Контакт 97 | IOR_3B — Bank 3 I/O pin |
| Контакт 98 | GND — Ground |
| Контакт 99 | VCCIO3 — Bank 3 I/O supply |
| Контакт 100 | IOR_4B — Bank 3 I/O pin |
| Контакт 101 | IOR_5B — Bank 3 I/O pin |
| Контакт 102 | IOR_6B — Bank 3 I/O pin |
| Контакт 103 | IOR_7B — Bank 3 I/O pin |
| Контакт 104 | IOR_8B — Bank 3 I/O pin |
| Контакт 105 | IOR_9B — Bank 3 I/O pin |
| Контакт 106 | IOR_10B — Bank 3 I/O pin |
| Контакт 107 | IOR_11B — Bank 3 I/O pin |
| Контакт 108 | VCC — Core supply |
| Контакт 109 | VCCIO3 — Bank 3 I/O supply |
| Контакт 110 | IOR_12B — Bank 3 I/O pin |
| Контакт 111 | IOR_13B — Bank 3 I/O pin |
| Контакт 112 | IOR_14B — Bank 3 I/O pin |
| Контакт 113 | IOR_15B — Bank 3 I/O pin |
| Контакт 114 | GND — Ground |
| Контакт 115 | INITN — Open-drain initialization complete signal |
| Контакт 116 | PROGRAMN — Active-low program / configuration reset |
| Контакт 117 | DONE — Open-drain configuration complete |
| Контакт 118 | CCLK — Configuration clock (for slave mode) |
| Контакт 119 | SI_SI — Slave serial input for SPI configuration |
| Контакт 120 | SO_SO — Slave serial output (MISO) |
| Контакт 121 | CSN — SPI chip select for configuration |
| Контакт 122 | VCCIO2 — Bank 2 I/O supply |
| Контакт 123 | IOL_0B — Bank 0 (bottom) I/O pin |
| Контакт 124 | IOL_1B — Bank 0 I/O pin |
| Контакт 125 | IOL_2B — Bank 0 I/O pin |
| Контакт 126 | IOL_3B — Bank 0 I/O pin |
| Контакт 127 | IOL_4B — Bank 0 I/O pin |
| Контакт 128 | IOL_5B — Bank 0 I/O pin |
| Контакт 129 | GND — Ground |
| Контакт 130 | VCCIO0 — Bank 0 I/O supply |
| Контакт 131 | IOL_6B — Bank 0 I/O pin |
| Контакт 132 | IOL_7B — Bank 0 I/O pin |
| Контакт 133 | IOL_8B — Bank 0 I/O pin |
| Контакт 134 | IOL_9B — Bank 0 I/O pin |
| Контакт 135 | IOL_10B — Bank 0 I/O pin |
| Контакт 136 | IOL_11B — Bank 0 I/O pin |
| Контакт 137 | IOL_12B — Bank 0 I/O pin |
| Контакт 138 | IOL_13B — Bank 0 I/O pin |
| Контакт 139 | IOL_14B — Bank 0 I/O pin |
| Контакт 140 | IOL_15B — Bank 0 I/O pin |
| Контакт 141 | GND — Ground |
| Контакт 142 | VCC — Core supply |
| Контакт 143 | VCCIO0 — Bank 0 I/O supply |
| Контакт 144 | NC — Not connected (per datasheet) |
Типичное применение
LCMXO2-7000HC-4TG144C подходит для 7 применениеs: Programmable Board Control and Power Sequencing, I2C / SPI / UART Bus Bridging, I/O Expansion and Level Translation, Display and LED Control, Motor Control Glue Logic, Industrial Control and White Goods HMI, Telecom Line Card Glue Logic.
Programmable Board Control and Power Sequencing
The LCMXO2-7000HC-4TG144C is well-suited to board-control tasks because it combines 6864 LUTs of glue-logic capacity with the MachXO2 family's signature instant-on non-volatile behavior. In this application, the device replaces multiple 74-series logic ICs, supervisors, and a configuration PROM by holding reset distribution, watchdog logic, power-rail sequencers, and I2C/SPI housekeeping in one part. Its 245 kbit embedded block RAM plus distributed RAM supports state-machine parameter storage, while hardened I/O banks accept 1.8 V, 2.5 V, and 3.3 V peripherals without external level shifters. Designers benefit from the 65 nm low-power process, which keeps standby current under 100 uA while preserving configuration.
Рекомендуется
I2C / SPI / UART Bus Bridging
Bus bridging between legacy microcontrollers and modern peripherals is a classic MachXO2 use case where the LCMXO2-7000HC-4TG144C shines. With 6864 LUTs the device can host multi-master I2C controllers, SPI-to-I2C bridges, UART-to-SPI converters, and protocol translation glue that would otherwise consume large amounts of MCU cycles. Per-bank VCCIO from 1.2 V to 3.3 V lets one FPGA bridge between 1.8 V sensors and a 3.3 V host MCU without external level translation. The on-chip flash configuration eliminates the boot PROM, reducing BOM cost and PCB area versus SRAM-based FPGA solutions.
Рекомендуется
I/O Expansion and Level Translation
Designers use the LCMXO2-7000HC-4TG144C to expand MCU GPIO counts and translate voltages between incompatible logic domains. The 114 user I/O pins give a small MCU up to 100+ extra general-purpose lines, each individually configurable as input, output, or open-drain with internal pull-ups. Eight I/O banks allow simultaneous 1.2 V, 1.8 V, 2.5 V, and 3.3 V peripherals on the same device. Compared to discrete level-translator ICs, the FPGA collapses multiple shifters into a single programmable part, simplifying layout and reducing component count on industrial and consumer boards.
Рекомендуется
Display and LED Control
The LCMXO2-7000HC-4TG144C is widely deployed as a low-cost display controller for small TFTs, segment LCDs, character displays, and large LED matrices. The 6864 LUTs handle display refresh, character RAM lookups, and PWM generation for LED dimming in parallel with a low-cost host MCU. The on-chip User Flash Memory (UFM) can store font tables and timing constants, offloading the host processor. Per the MachXO2 family datasheet, the device supports LVCMOS 3.3 V and LVDS outputs suitable for direct drive of small LCD panels and LED driver ICs.
Рекомендуется
Motor Control Glue Logic
Motor control systems need fast, deterministic glue logic between a DSP/MCU, gate drivers, and feedback sensors, exactly the role the LCMXO2-7000HC-4TG144C fills. The 6864 LUTs can implement encoder decoding (QEI), Hall-sensor commutation tables, PWM protection, fault logging, and SPI links to intelligent gate drivers. Its commercial 0 C to 85 C temperature grade covers most indoor motor applications, while the LCMXO2-7000HC-4TG144I industrial variant extends to outdoor or under-hood environments. The 65 nm low-power process ensures the FPGA itself does not heat the enclosure.
Рекомендуется
Industrial Control and White Goods HMI
The LCMXO2-7000HC-4TG144C is a strong fit for industrial control boards and white-goods human-machine interfaces (HMIs) where reliability, instant-on, and field upgradability matter. Typical functions include keypad scanning, LED matrix driving, seven-segment display control, buzzer PWM, and interface isolation between analog front-ends and the main MCU. Because the MachXO2 retains bitstream without an external PROM, white-goods designs can survive brown-outs and brown-out resets without reconfiguration delays. The device is RoHS3 compliant and Lead Free per the Lattice product page, meeting modern environmental directives.
Рекомендуется
Telecom Line Card Glue Logic
Telecom line cards use the LCMXO2-7000HC-4TG144C for backplane bridging, I2C muxing, interrupt aggregation, and low-speed SERDES replacement. Its 6864 LUTs and 114 I/O easily handle dozens of status LEDs, alarm outputs, and sideband signals. The hardened LVDS pairs support point-to-point sideband communications between line-card MCUs and the chassis supervisor. Compared to discrete logic, the MachXO2 consolidates 5 to 10 small logic ICs into a single programmable part, reducing board area and improving reliability.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LCMXO2-7000HC-4TG144C — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LCMXO2-4000HC-4TG144C | LCMXO2-7000HE-4TG144C | LCMXO2-7000HC-6TG144C | LCMXO2-7000HC-4TG144I | LCMXO2-2000HC-4TG144C |
|---|---|---|---|---|---|---|
| Package | 144-TQFP | 144-TQFP (same) | 144-TQFP (same) | 144-TQFP (same) | 144-TQFP (same) | 144-TQFP (same) |
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Number of LUTs | 6864 | 4320 (-37%) | 6864 (same) | 6864 (same) | 6864 (same) | 2112 (-69%) |
| Number of I/O | 114 to 115 | 114 (same) | 114 (same) | 114 (same) | 114 (same) | 114 (same) |
| Speed Grade | 4 | 4 (same) | 4 (same HE) | 6 (slower) | 4 (same) | 4 (same) |
| Embedded Block RAM | 245 kbit | 92 kbit (-62%) | 245 kbit (same) | 245 kbit (same) | 245 kbit (same) | 34 kbit (-86%) |
| Operating Temperature | 0 C to +85 C (Commercial) | 0 C to +85 C | 0 C to +85 C | 0 C to +85 C | -40 C to +100 C (Industrial) | 0 C to +85 C |
| Configuration Memory | On-chip flash (non-volatile) | On-chip flash | On-chip flash | On-chip flash | On-chip flash | On-chip flash |
| RoHS Compliance | RoHS3 Compliant | RoHS3 Compliant | RoHS3 Compliant | RoHS3 Compliant | RoHS3 Compliant | RoHS3 Compliant |
Ключевые отличия
- Higher LUT count and EBR than the LCMXO2-4000HC-4TG144C in the same 144-TQFP footprint (против LCMXO2-4000HC-4TG144C)
- Same LUT architecture as the LCMXO2-7000HE-4TG144C but lower power consumption (против LCMXO2-7000HE-4TG144C)
- On-chip non-volatile flash configuration eliminates external boot PROM (против SRAM-based FPGAs in similar 144-TQFP packages)
- Hardened I/O banks support 1.2 V to 3.3 V mixed-voltage designs (против Discrete level-translator ICs plus a CPLD)
Заметки по проектированию
The LCMXO2-7000HC-4TG144C requires separate decoupling on VCC (core), VCCIOx (per I/O bank), and VCCAUX (PLL analog). Place a 0.1 uF X7R ceramic cap on every VCC/VCCIO/VCCAUX pin pair, and add a bulk 10 uF tantalum or ceramic within 1 inch of the package. Estimated: with 114 I/O at 8 mA each switching at 50 MHz, expect core current draw of approximately 80 to 120 mA - mark the supply with at least 250 mA headroom.
Route clock traces first with controlled impedance and short stubs. Per the MachXO2 family datasheet, the PLL analog supply VCCAUX must be filtered with a ferrite bead or 10 ohm resistor in series and decoupled to analog ground (GNDA) for low PLL jitter. Keep all PLL clock traces away from switching I/O on adjacent layers to avoid coupling.
Do not leave JTAG pins floating; if JTAG is unused, route TDI, TMS to a defined logic level via internal pull-ups. Per the MachXO2 datasheet, an unconnected TCK can cause spurious configuration requests. Also confirm that PROGRAMN is tied high through a 1 kohm to 10 kohm resistor, not driven low at power-up, to avoid an inadvertent configuration cycle.
When using LVDS pairs on the MachXO2, match trace lengths within 150 mil and maintain 100 ohm differential impedance. Series-couple each LVDS pair with a 100 ohm resistor near the driver pin. Estimated: differential return loss above 10 dB at 200 MHz is achievable on standard 4-layer FR-4 with proper stack-up. Consult the MachXO2 hardware checklist for working with silicon guidance.
Place all decoupling capacitors on the same layer as the FPGA, within 100 mil of their respective supply pin. Use a continuous ground plane on layer 2 for shortest return paths. Per the Lattice hardware checklist, vias-in-pad are acceptable for the 144-TQFP thermal pad, which should be soldered to a copper pad connected to the ground plane for improved thermal dissipation.
Информация о соответствии
RoHS3 Compliant and Lead Free per Lattice product page. REACH compliance status not detailed in the verified snippets. AEC-Q100 not applicable - Lattice does not qualify MachXO2 to automotive grade; choose LCMXO2-7000HC-4TG144I only for industrial temperature ranges, not for AEC-Q100 automotive designs.
