LM258AMX - Dual 3-32V Op Amp | onsemi | 8-SOIC
Артикул: LM258AMX ✓ АктивенLM258AMX Обзор
An operational amplifier is an active analog signal-processing component that uses differential input voltage to control an output voltage. A dual operational amplifier combines two amplifiers in one package, reducing board area and simplifying power-supply routing. The LM258AMX combines this general-purpose amplifier function with internal frequency compensation, allowing stable operation at unity gain without an external compensation capacitor. This makes it useful in designs where the signal source does not require a specialized low-noise or high-speed amplifier.
The main electrical features of the LM258A family include internal frequency compensation for unity gain, 100 dB large DC voltage gain, and a wide power-supply range. The input common-mode voltage range includes ground, which permits the amplifier to process signals close to the lower supply rail. The output swing is characterized as extending to VCC minus 1.5 V, a relevant consideration when the amplifier must drive an ADC, a relay driver, or another circuit with limited headroom. The 8-SOIC package is a standard surface-mount format suitable for conventional PCB assembly.
Typical uses include current sensing in industrial control equipment, signal conditioning in sensor interfaces, audio preamplifier stages, feedback networks in power converters, and general instrumentation. In a current-sense amplifier, the two independent channels can monitor different loads or provide differential amplification stages. In a sensor interface, the input common-mode range can simplify conditioning of signals referenced to ground. Designers should still account for the output-voltage headroom, supply decoupling, input bias currents, and the frequency-response limits of the selected amplifier configuration.
The LM258AMX is appropriate when a design needs two amplifiers, a broad single-supply operating range, and a familiar 8-pin SOIC footprint. It is less suitable for applications requiring very low noise, rail-to-rail input or output operation, high slew rate, or precision offset and drift performance. This page combines the manufacturer-family electrical characteristics with package information, application guidance, and practical design considerations for evaluating the part in new analog circuits.
Аналоги без доработки для LM258AMX — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM258AMX (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Package, Gain-Bandwidth Product, Number of Amplifiers, Maximum Supply Voltage.
LM258ADR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM258AMX
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM358AMX/NOPB
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM358ADR2G
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM358DR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM258AMX Максимальные параметры и электрические характеристики
| Number of Amplifiers | 2 amplifiers |
| Amplifier Type | Dual operational amplifier |
| Architecture | Independent amplifiers |
| Supply Voltage Range | 3 V to 32 V |
| Large DC Voltage Gain | 100 dB |
| Frequency Compensation | Internally frequency compensated for unity gain |
| Input Common-Mode Voltage Range | Includes ground |
| Output Voltage Swing | DC to VCC - 1.5 V |
| Корпус | 8-pin SOIC |
| Тип монтажа | Surface mount |
| Lead-Free Status | Lead free |
| Статус RoHS | RoHS compliant |
Руководство по цоколевке LM258AMX в корпусе 8-pin soic
Цоколевка для LM258AMX (корпус 8-pin soic). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для LM258AMX.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM258AMX подходит для 6 применениеs: Industrial Current-Sense Interface, Sensor Signal Conditioning, Audio Preamplifier, Power-Supply Feedback Network, Data-Acquisition Analog Front End, General Instrumentation Buffer.
Industrial Current-Sense Interface
The LM258AMX suits industrial current-sense signal conditioning because the LM258A family provides two independent amplifiers with 100 dB large DC voltage gain and internal frequency compensation for unity gain. Place one channel in a differential amplifier around a low-value shunt and use the other channel for an offset or reference buffer. The 3 V to 32 V supply range supports control equipment operating from low-voltage logic rails through higher industrial supplies, while the input common-mode range that includes ground helps process measurements referenced to the lower rail. Check the shunt, input protection, output swing, and amplifier stability at the selected gain before production release.
Рекомендуется
Sensor Signal Conditioning
The LM258AMX can condition low-frequency sensor signals in instrumentation and factory-control systems. Its two independent channels can amplify a sensor output and buffer a reference or feedback node, reducing the number of separate amplifier packages. Internal frequency compensation supports unity-gain operation, and the 100 dB large DC voltage gain is useful for common-mode rejection in a differential input stage. Because the amplifier is not described as rail-to-rail, verify that the sensor signal and resulting output remain inside the input common-mode and approximately VCC minus 1.5 V output limits.
Рекомендуется
Audio Preamplifier
The LM258AMX is suitable for general-purpose audio preamplifier stages that do not require ultra-low-noise performance. Two independent channels can support left and right signal paths in a small audio system, while internal frequency compensation simplifies unity-gain voltage-follower or moderate-gain designs. The 3 V to 32 V supply range permits operation from a single low-voltage rail, and the common-mode range that includes ground supports signals centered near the lower supply rail. The output must remain below approximately VCC minus 1.5 V, so headroom should be evaluated for headphone, line-level, or mixer interfaces.
Рекомендуется
Power-Supply Feedback Network
The two amplifiers in the LM258AMX can be used in feedback and error-amplifier positions for a simple power-control design. One channel may compare a feedback voltage with a reference, while the other channel can buffer the error or drive a monitoring node. The internal unity-gain compensation and 100 dB large DC voltage gain are useful for closed-loop voltage-control applications, and the 3 V to 32 V supply range supports a broad range of control rails. The design must account for the output swing limit, load capability, loop compensation, and the risk of saturation during startup or transient conditions.
Рекомендуется
Data-Acquisition Analog Front End
The LM258AMX can form part of an analog front end ahead of an ADC or data-conversion system. Its differential-input capability supports amplification of small signals referenced to ground, while the second channel can provide gain or buffering for a second analog channel. Internal frequency compensation makes the device straightforward to use at unity gain, and the broad supply range allows the analog section to share a supply with many control systems. Validate input bias-current error, input offset, output-swing margin, and bandwidth against the acquisition system before using the device with high-impedance sources.
Рекомендуется
General Instrumentation Buffer
The LM258AMX fits instrumentation buffers where two independent voltage followers or fixed-gain stages are useful in a limited board area. The internal frequency compensation for unity gain reduces the need for external compensation components, and the high DC gain supports accurate closed-loop operation when feedback resistors are used. The input common-mode range includes ground, which is advantageous for low-level signals referenced to the lower supply rail. For instrumentation applications, verify offset voltage, drift, input bias current, noise, and input/output impedance from the complete manufacturer specifications because those values are not present in the visible source excerpts.
Рекомендуется
Справочные инженерные данные для LM258AMX — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM258ADR | LM258AMX | LM358AMX | LM358ADR | LM358DR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | onsemi |
| Number of Amplifiers | 2 independent amplifiers | 2 independent amplifiers | 2 independent amplifiers | 2 independent amplifiers | 2 independent amplifiers | 2 independent amplifiers |
| Supply Voltage Range | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V |
| Large DC Voltage Gain | 100 dB | 100 dB | 100 dB | 100 dB | 100 dB | 100 dB |
| Frequency Compensation | Internal, unity gain | Internal, unity gain | Internal, unity gain | Internal, unity gain | Internal, unity gain | Internal, unity gain |
| Input Common-Mode Range | Includes ground | Includes ground | Includes ground | Includes ground | Includes ground | Includes ground |
| Output Voltage Swing | DC to VCC - 1.5 V | DC to VCC - 1.5 V | DC to VCC - 1.5 V | DC to VCC - 1.5 V | DC to VCC - 1.5 V | DC to VCC - 1.5 V |
Ключевые отличия
- Two independent amplifiers in one 8-pin SOIC (против LM258ADR)
- Internal unity-gain frequency compensation (против LM358AMX)
- Single-supply input operation includes ground (против LM358DR)
Заметки по проектированию
Decouple each LM258AMX supply connection close to the device with the manufacturer-recommended ceramic capacitance and maintain a short ground return. Because the LM258AMX supports a 3 V to 32 V supply range, the selected bypass network must remain suitable for the actual rail voltage and expected transient bandwidth. Check the output swing against the load requirement: the documented limit is DC to VCC - 1.5 V, so a downstream stage requiring a near-rail input needs additional headroom.
Use the 8-pin SOIC land pattern and follow the manufacturer pin-description table when assigning the two amplifier channels. Route each input and output directly to its intended circuit, keep the feedback loop compact, and avoid sharing long analog paths with switching or high-current return paths. A common ground reference is essential for both channels; poor ground-current routing can inject noise that appears as common-mode or output disturbance.
Do not treat the LM258AMX as a rail-to-rail amplifier. The documented output swing reaches only to approximately VCC - 1.5 V, while the input common-mode range includes ground but does not imply operation at the positive supply rail. Confirm the required input range, output range, load, gain, and frequency response in the complete manufacturer datasheet before substituting an LM258A, LM358A, or LM2904-family device.
Информация о соответствии
The visible LM258AMX specifications identify lead-free construction and RoHS compliance. Other compliance and qualification attributes require confirmation from the manufacturer.