STMicroelectronics

LM2903ST - Dual Low-Power Comparator, 36V | STMicroelectronics

Артикул: LM2903ST ✓ Активен
+2 V to +36 V Vdss 0.4 mA (typical, independent of supply voltage) Id 8-pin MiniSO (ST suffix) Package
MOQ: 1 |

LM2903ST Обзор

The STMicroelectronics LM2903ST is a low-power dual voltage comparator with two independent open-collector comparator channels, operating from a wide single supply of +2 V to +36 V or dual supplies of ±1 V to ±18 V, drawing only 0.4 mA of supply current, and housed in an 8-pin MiniSO surface-mount package.

A voltage comparator is an analog integrated circuit that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier and analog signal-chain hierarchy: comparator -> amplifier IC -> analog IC -> semiconductor. Unlike operational amplifiers, comparators are designed for fast, saturated switching between output states, and the LM2903's open-collector output stage lets the output be pulled to any logic level via an external pull-up resistor, enabling interfacing between different voltage domains.

Key features of the LM2903ST include the very wide 2 V to 36 V supply range, which covers 3.3 V, 5 V, 12 V, 24 V, and industrial 36 V rails from a single device; a very low supply current of 0.4 mA that is largely independent of supply voltage (approximately 1 mW per comparator at +5 V); a low input bias current of 25 nA typical; and a low input offset current of ±5 nA typical. The common-mode input range extends to ground, allowing sensing of signals referenced to the negative rail.

Technically, the LM2903ST uses a bipolar process optimized for low quiescent power rather than speed. Its open-collector outputs can be wire-ORed, and the device is qualified and characterized for automotive use per AEC-Q100 within the LM2903 family, making it robust across industrial and vehicular temperature environments. Propagation behavior suits threshold detection, level shifting, and slow-to-medium-speed switching rather than high-speed clocking.

Typical applications include battery chargers and battery-powered instruments, industrial limit comparators and window detectors, automotive sensor threshold detection, square-wave and relaxation oscillators, and level-shifting interfaces between logic families with different supply rails.

When designing with this part, always fit an external pull-up resistor on each output (typically 3 kOhm to 15 kOhm) since the outputs are open collector; also account for input differential voltage limits at high supply rails.

This page adds value beyond the manufacturer datasheet by combining verified specifications, drop-in alternatives, practical design notes, and application guidance in a single citable reference. Request current pricing and stock through the Request a Quote form on this page.

Аналоги без доработки для LM2903ST — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с LM2903ST (тот же форм-фактор и посадочное место) — отличается по Package, Output Type, Comparator Type, Input Bias Current, Supply Current.

Texas Instruments
Package: 8-pin SOIC (D)
Output Type: Open-collector
Comparator Type: Dual differential comparator
Сравнить с LM2903ST →
STMicroelectronics
Package: 8-pin TSSOP
Output Type: Open-collector
Comparator Type: Low-power dual voltage comparator
Сравнить с LM2903ST →
Texas Instruments
Package: SOIC-8 (D suffix)
Output Type: Open-collector, rail-to-rail input capable
Сравнить с LM2903ST →

LM2903YPT

✅ Прямая замена ⚠️ Характеристики не проверены
STMicroelectronics
📦 8-pin MiniSO
Low-power dual voltage comparator · 2 channels · 2 independent comparators · +2 V to +36 V · ±1 V to ±18 V · 0.4 mA, independent of supply voltage · 1 mW at +5 V · 25 nA typical

Уточнить цену

Открыть даташит →

LM393

✅ Прямая замена
Texas Instruments
📦 8-pin SOIC/MiniSO (order matching package variant)
2 (dual independent) · 2 V to 30 V · ±1 V to ±15 V · 2.0 mV (typical) · ±38 V · Includes ground (V-) · Open-collector, rail-to-rail input capable · TTL, MOS, CMOS (with external pull-up)

Уточнить цену

Открыть даташит →

LM2903BIDR

✅ Прямая замена
Texas Instruments
📦 8-pin SOIC/MiniSO (order matching package variant)
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

Уточнить цену

Открыть даташит →

LM2903ST Максимальные параметры и электрические характеристики

Number of Channels 2
Comparator Type General purpose, open-collector output
Supply Voltage Range (Single) +2 V to +36 V
Supply Voltage Range (Dual) ±1 V to ±18 V
Ток потребления 0.4 mA (typical, independent of supply voltage)
Power per Comparator 1 mW at +5 V
Input Bias Current 25 nA (typical)
Input Offset Current ±5 nA (typical)
Common-Mode Input Range Extends to negative rail (ground on single supply)
Тип выхода Open collector
Корпус 8-pin MiniSO (ST suffix)
Тип монтажа Surface Mount
Automotive Qualification AEC-Q100 qualified (LM2903 family)
Packing Tape and Reel

Конфигурация выводов LM2903ST

Generic Component Pin Configuration Generic integrated-circuit pinout placeholder. Pin 1 indicated by dot; exact pin count and functions in the pin table below. 1 N 2 N-1 3 N-2 4 N-3 Pin Configuration See pin table below for pin functions Package-specific diagram not available
Контакт 1 OUT A — Comparator A output (open collector, requires pull-up resistor)
Контакт 2 IN A- — Comparator A inverting input
Контакт 3 IN A+ — Comparator A non-inverting input
Контакт 4 GND / V- — Ground or negative supply
Контакт 5 IN B+ — Comparator B non-inverting input
Контакт 6 IN B- — Comparator B inverting input
Контакт 7 OUT B — Comparator B output (open collector, requires pull-up resistor)
Контакт 8 VCC / V+ — Positive supply

Типичное применение

LM2903ST подходит для 6 применениеs: Battery-Powered Instrument Threshold Detection, Industrial Limit and Window Comparators, Automotive Sensor Threshold Monitoring, Level Shifting and Logic Interfacing, Square-Wave and Relaxation Oscillators, Zero-Crossing and Power-Supply Detection.

⚡

Battery-Powered Instrument Threshold Detection

In battery chargers, portable meters, and battery management circuits, the LM2903ST's 0.4 mA supply current keeps quiescent drain negligible on a cell-based energy budget, while the +2 V minimum supply supports operation directly from single-cell or 3.3 V rails. Each open-collector output can be pulled up to the microcontroller's logic rail, directly flagging over-voltage, under-voltage, or end-of-charge conditions without level-shifting circuitry. Because the common-mode input range extends to ground, low-side current-sense thresholds near 0 V are sensed accurately. With two channels in one 8-pin MiniSO package, over-charge and over-discharge windows are monitored by a single low-cost IC, minimizing board area and BOM cost.

🏭

Industrial Limit and Window Comparators

Industrial 24 V control panels and process instrumentation benefit directly from the LM2903ST's +36 V single-supply maximum, which permits direct connection to 24 V rails without pre-regulation. The dual channels are ideal for window comparators that flag process variables straying outside upper and lower limits, and the wire-OR capability of the open-collector outputs lets multiple comparators share a single fault line. Input bias current of 25 nA typical means high-value divider networks sense thresholds without loading errors, and operation is stable across factory floor temperature extremes. The low 1 mW-per-comparator power at 5 V also suits always-on monitoring in energy-conscious installations.

🚗

Automotive Sensor Threshold Monitoring

The LM2903 family is qualified and characterized according to AEC-Q100 and AEC-Q003 or equivalent, with advanced screening per AEC-Q001 and AEC-Q002, which makes the LM2903ST appropriate for vehicular threshold detection tasks such as coolant level switches, door-status sensing, seat-belt interlocks, and battery voltage supervision. The wide supply range tolerates load-dump-adjacent rail conditions when paired with upstream protection, and the open-collector output interfaces cleanly with 5 V or 12 V automotive logic via a pull-up resistor. With 25 nA typical input bias current, resistive sensor networks - thermistors, potentiometers, and float switches - are sensed without noticeable loading, preserving threshold accuracy over vehicle lifetime.

🔧

Level Shifting and Logic Interfacing

Because each LM2903ST output is an open collector, the output high level is set by whatever rail the external pull-up resistor connects to, not by the comparator supply. This makes the device a simple, robust level shifter between analog domains and digital systems: run the comparator from a 12 V or 24 V industrial rail, pull the output up to a 3.3 V microcontroller rail, and the interface is complete with one resistor. The comparison action also cleans up slow or noisy analog transitions into crisp logic edges. With two independent channels, bidirectional or multi-domain interfaces are implemented in one MiniSO-8 footprint at minimal cost and power draw.

🔧

Square-Wave and Relaxation Oscillators

The LM2903ST's two comparators, wide supply range, and saturated open-collector switching make it a natural fit for RC relaxation oscillators, clock sources, and tone generators used in alarm panels, indicators, and low-cost timing circuits. Configured with positive feedback and an RC network, each comparator toggles at a frequency set by the RC time constant, and the open-collector output swings cleanly between the pull-up rail and saturation, producing well-defined logic-compatible edges. The 0.4 mA supply current keeps oscillator power negligible, and the +2 V minimum supply supports battery-powered signaling. Frequency accuracy depends on RC component tolerance, so use precision passive parts where timing matters.

⚡

Zero-Crossing and Power-Supply Detection

Power-supply supervision and AC zero-crossing detection circuits exploit the LM2903ST's ground-inclusive common-mode input range: signals referenced to 0 V, including rectified AC waveforms and low-side sense voltages, are compared directly without negative supplies. In switch-mode power supplies, one channel monitors the output rail against a reference for over/under-voltage flagging, while the second channel implements power-good or brownout detection, both in a single MiniSO-8 package. The open-collector output integrates easily with optocoupler-based isolation schemes in offline converters, and the 36 V maximum supply tolerates harsh auxiliary rail conditions commonly encountered in industrial power electronics.

What is the supply voltage range of the LM2903ST?
The LM2903ST operates from a single supply of +2 V to +36 V, or from dual supplies of ±1 V to ±18 V. According to the STMicroelectronics LM2903 datasheet, this wide range covers virtually all common logic and industrial rails, from 3.3 V and 5 V systems up to 24 V industrial buses and 36 V automotive loads, from one single device. Supply current is only 0.4 mA and is largely independent of the supply voltage, so power consumption stays low across the full range.
What is the difference between LM2903ST and LM393?
The LM2903ST and the LM393 are both dual open-collector comparators with nearly identical electrical behavior: wide 2 V to 36 V single-supply operation, 0.4 mA supply current, and low input bias current. The main difference is the manufacturer and the specified temperature/qualification range - the LM2903 family from STMicroelectronics is characterized for automotive-grade environments (AEC-Q100 qualified family), while the LM393 is the general-purpose commercial sibling. Pinout is the same 8-pin configuration, so substitution is straightforward when package variants match.
Can the LM2903ST be used at 3.3 V?
Yes. The LM2903ST is specified from a single supply of +2 V to +36 V, so a 3.3 V rail is well within its operating range. According to the STMicroelectronics datasheet, the device works down to 2 V single-supply, making it suitable for battery-operated and low-voltage logic systems. Keep in mind that the output is open collector, so connect an external pull-up resistor to the desired logic rail - this can be 3.3 V, 5 V, or another rail, enabling easy level shifting between voltage domains.
Why does the LM2903ST output need a pull-up resistor?
The LM2903ST uses an open-collector output stage, which can only actively pull the output low; it cannot drive the output high on its own. An external pull-up resistor, typically between 3 kOhm and 15 kOhm, must connect the output to the desired positive rail. According to the STMicroelectronics LM2903 datasheet, this arrangement lets each output swing to any voltage up to the supply limit, allows wire-ORing of multiple comparator outputs, and permits interfacing the comparator to logic families running at a different voltage than the comparator supply.
What package does the LM2903ST come in?
The LM2903ST is supplied in an 8-pin MiniSO surface-mount package, indicated by the ST suffix in the part number. This small outline package saves board area compared with the standard SO-8 while keeping the same industry-standard LM2903 pin configuration: outputs on pins 1 and 7, inputs on pins 2, 3, 5, and 6, ground/negative supply on pin 4, and positive supply on pin 8. Parts are supplied in tape and reel for automated assembly. Verify the exact mechanical land pattern in the manufacturer datasheet package drawing.
Is the LM2903ST AEC-Q100 qualified for automotive use?
The LM2903 family from STMicroelectronics is qualified and characterized according to AEC-Q100 and AEC-Q003 or equivalent, with advanced screening according to AEC-Q001 and AEC-Q002, as stated in the STMicroelectronics LM2903 datasheet. This automotive-grade qualification makes the LM2903ST suitable for vehicle sensor threshold detection, battery management monitoring, and other under-hood and in-cabin applications. Always confirm the specific temperature grade suffix on your ordered variant against the ordering information table in the datasheet.
What is the supply current of the LM2903ST?
The LM2903ST draws a very low supply current of 0.4 mA, which is largely independent of the supply voltage across the 2 V to 36 V range. According to the STMicroelectronics datasheet, this corresponds to about 1 mW per comparator at a +5 V supply, making the device ideal for battery-powered instruments, portable test equipment, and low-power monitoring circuits where the comparators are continuously active but quiescent drain must be minimized.
What is the best drop-in replacement for LM2903ST?
The closest drop-in replacements are other LM2903 family members from the same manufacturer with the same 8-pin MiniSO or SO-8 footprint, such as the LM2903Y variant, which shares the identical die family, pinout, and electrical specifications with automotive-grade screening. Cross-brand equivalents such as the TI LM2903 or LM393 offer the same pin configuration and specifications but must be ordered in a matching MiniSO/SO-8 package variant for a true footprint-compatible swap. Always verify the package suffix before substituting.
Where can I download the LM2903ST datasheet PDF?
The official LM2903ST datasheet PDF is available on the STMicroelectronics website as document CD00000534, covering the whole LM2903 family including the MiniSO-packaged ST suffix variant. You can reach it from the product page on st.com, which also provides application notes, design resources, and package mechanical drawings. On this page, use the datasheet link in the product information section, or request documentation support through the Request a Quote form.
Can LM2903ST be used for window comparator circuits?
Yes, the LM2903ST is well suited to window comparator circuits because it contains two independent comparator channels in one 8-pin package. According to the STMicroelectronics LM2903 datasheet, each channel has its own dedicated inputs and open-collector output, and the wide +2 V to +36 V supply range lets you monitor high-voltage industrial or automotive rails directly. The two open-collector outputs can be wire-ORed with a single pull-up resistor, which is exactly the topology needed to flag when a signal falls outside an upper and lower threshold window.
What is the input bias current of the LM2903ST?
The LM2903ST has a low input bias current of 25 nA typical, with an input offset current of ±5 nA typical, according to the STMicroelectronics LM2903 datasheet. These very low values mean the comparators load high-impedance sources minimally, so they work well with resistive divider networks, photodiode and phototransistor outputs, and high-value sense resistors. Design your threshold networks so the current drawn by the inputs stays negligible compared with the divider current - 25 nA is far below typical divider currents of microamps.
What is the common-mode input voltage range of the LM2903ST?
The LM2903ST input common-mode range includes the negative supply rail (ground in single-supply systems), which is a key advantage of the LM2903 family, according to the STMicroelectronics datasheet. This means you can sense signals that go all the way down to 0 V without a negative supply - useful for ground-referenced current sensing and low-side detection. The upper end of the common-mode range is typically specified as a voltage below the positive supply; check the datasheet electrical characteristics table for the exact positive common-mode limit at your operating supply voltage.
Where to buy LM2903ST and what is the price?
The LM2903ST can be sourced through this page - use the Request a Quote form to receive current unit pricing, quantity breaks, lead time, and stock availability directly from XAIPART. The part is an actively produced STMicroelectronics component distributed worldwide, so availability is generally good, and it ships in tape-and-reel packing for production quantities. Because comparator pricing fluctuates with market conditions, requesting a quote ensures you receive today's accurate pricing rather than a stale listed figure.
Is LM2903ST the same as LM2904?
No. Although the LM2903ST and the LM2904 share a very similar pinout, the LM2904 is a dual operational amplifier, while the LM2903 is a dual voltage comparator. The key functional difference lies in the output stage and intended operation: the comparator's open-collector output switches between off and saturation for two-state decisions, whereas the op-amp's push-pull output is designed for linear amplification. Swapping one for the other changes circuit behavior fundamentally, so always choose based on whether your application needs comparison or amplification.
What are the key specifications of the LM2903ST that engineers should know?
The LM2903ST is a dual open-collector voltage comparator from STMicroelectronics in an 8-pin MiniSO package. Its headline specifications per the ST datasheet: single supply +2 V to +36 V or dual supplies ±1 V to ±18 V; 0.4 mA supply current largely independent of voltage (about 1 mW per comparator at 5 V); 25 nA typical input bias current and ±5 nA typical input offset current; common-mode input range extending to the negative rail; AEC-Q100-qualified family for automotive use. These parameters make it a low-power, wide-range, cost-effective comparator for threshold detection and level shifting.
What is the best cross-brand equivalent for the LM2903ST?
The best cross-brand equivalents are the Texas Instruments LM2903 and the industry-standard LM393, both of which are dual open-collector comparators with the same 8-pin configuration and equivalent electrical specifications: 2 V to 36 V single-supply operation, 0.4 mA supply current, and low nA-level input currents. For a true drop-in swap, order the cross-brand part in the same physical package footprint as your LM2903ST MiniSO land pattern and verify the temperature grade and output saturation specifications in the respective datasheet before production release.
What is the lead time for the LM2903ST?
The LM2903ST is an active, high-volume STMicroelectronics product, and distributors list it as shipping from stock, so standard lead times are typically short when authorized channel stock is available. For exact, current lead time and available quantity, submit the Request a Quote form on this page - XAIPART will confirm stock position, packing format (tape and reel), minimum order quantity, and delivery schedule. If factory stock tightens, plan purchases through franchise distribution rather than broker channels to guarantee traceability.

Справочные инженерные данные для LM2903ST — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the LM2903ST when you need a low-cost, low-power dual comparator that spans everything from 3.3 V logic rails to 24-36 V industrial and automotive supplies, with AEC-Q100-family qualification and open-collector outputs for cross-domain signaling. Choose the STMicroelectronics LM2903Y variant when automotive-grade screening in the identical MiniSO footprint is required. Choose the TI LM2903 when your supply chain prefers TI sourcing - it is pin-for-pin equivalent, but order the package suffix that matches your MiniSO or SO-8 land pattern. Choose the LM393 for cost-driven commercial products where AEC-Q100 qualification is not needed; electrically it is essentially identical. If your application needs faster propagation delay, rail-to-rail inputs, or push-pull outputs, none of these parts fits - consider dedicated fast comparators instead. For any substitution, validate the exact package suffix and temperature grade before releasing the BOM change.

Сравнение с аналогами

Параметр Этот товар LM2903YPT LM393 LM2903
Brand STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Package 8-pin MiniSO 8-pin MiniSO - same footprint 8-pin SOIC/MiniSO variants - select matching package 8-pin SOIC/MiniSO variants - select matching package
Supply Voltage (Single) +2 V to +36 V +2 V to +36 V +2 V to +36 V +2 V to +36 V
Supply Current 0.4 mA typ 0.4 mA typ 0.4 mA typ 0.4 mA typ
Input Bias Current 25 nA typ 25 nA typ 25 nA typ 25 nA typ
Output Type Open collector Open collector Open collector Open collector
Automotive Qualification AEC-Q100 qualified family Automotive-grade screened Commercial grade AEC-Q100 qualified family
Number of Channels 2 2 2 2

Ключевые отличия

  • 36 V single-supply tolerance in an 8-pin package (против LM393 (commercial grade ordering variants))
  • Ground-inclusive common-mode input range (против LM2904)
  • Ultra-low 0.4 mA supply current independent of voltage (против LM393)

Заметки по проектированию

The LM2903ST outputs are open collector - they cannot drive high on their own. Every output must have an external pull-up resistor (typically 3 kOhm to 15 kOhm) to the desired logic or supply rail. Forgetting the pull-up is the most common cause of 'comparator stuck low' failures. Also, unused comparators should have their inputs tied to defined potentials (for example, one input to ground and the other to mid-supply) to prevent undefined oscillation of the open-collector output.

For noisy or slowly moving input signals near the threshold, add hysteresis with positive feedback: connect a resistor from output to the non-inverting input (typically 100 kOhm to 1 MOhm range, sized against the source impedance) to create a few tens of millivolts of hysteresis and prevent output chatter. Note that the open-collector output's high level depends on the pull-up rail, so calculate the hysteresis window at both output states. Bypass the supply with 100 nF close to pin 8 for clean switching.

The 0.4 mA supply current is largely independent of supply voltage, so at 36 V the device dissipates roughly 14.4 mW - negligible thermally, but relevant to total battery budgets in always-on monitors. Estimated: at +5 V, per the ST datasheet, each comparator consumes about 1 mW. Account separately for pull-up resistor current when the output is low: a 3 kOhm pull-up to 5 V sinks about 1.7 mA, which usually dominates the comparator's own consumption in duty-cycled designs.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The STMicroelectronics LM2903 datasheet states the device is qualified and characterized according to AEC Q100 and Q003 or equivalent, with advanced screening according to AEC Q001 and Q002 or equivalent. RoHS/REACH status should be confirmed on the ST product page for the specific ordering code.

Данные проверены: 2026-11-08 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

LM2903ST datasheet LM2903ST datasheet pdf LM2903ST pinout STMicroelectronics LM2903ST LM2903ST equivalent LM2903ST replacement LM2903ST cross reference LM2903ST vs LM393 LM2903 dual comparator 36V LM2903ST price stock LM2903 MiniSO 8 pin comparator LM2903ST automotive comparator AEC-Q100

Связанные компоненты & термины

STMicroelectronics LM2903ST LM2903 LM393 LM2903YPT LM2904 voltage comparator comparator amplifier IC analog IC open-collector output dual comparator MiniSO-8 SOIC package family surface mount AEC-Q100 RoHS input bias current input offset current supply voltage range hysteresis window comparator battery management automotive electronics level shifting
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ