LM324KNSR - Quad 30-V 1.2-MHz Op Amp | Texas Instruments
Артикул: LM324KNSR ✓ АктивенLM324KNSR Обзор
An operational amplifier, or op amp, is a high-gain differential amplifier that compares two input voltages and drives its output to represent their difference. Within the broader semiconductor hierarchy, an op amp is an analog amplifier IC used for signal conditioning, buffering, amplification, filtering, feedback control, and voltage-level conversion. The LM324KNSR integrates four such amplifiers into one package, reducing board area compared with four separate single or dual amplifier packages.
The principal device ratings include operation from a single or split supply, a 30 V maximum supply voltage, 1.2 MHz gain-bandwidth bandwidth, and 2 kV improved ESD protection. The manufacturer identifies LM324KNSR as a standard general-purpose amplifier with four circuits and a 14-pin SOP package. Its specified operating-temperature range is 0 to 70 °C, making it appropriate for commercial equipment where an extended industrial temperature rating is not required.
The LM324K family is designed for broad compatibility with established LM324-type amplifier boards. Because the four amplifiers share a common package but operate independently, separate signal paths can be implemented within one device. The frequency-compensated architecture simplifies closed-loop use when the amplifier is configured as a standard inverting or non-inverting gain stage, although loop stability and bandwidth still depend on the external feedback network and load.
Typical uses include audio preamplification, sensor signal conditioning, current-to-voltage conversion, active filtering, voltage comparison, and general instrumentation. The four-amplifier arrangement is especially useful when a design needs several channels of similar gain and bandwidth, such as multiple sensor inputs or a balanced differential stage followed by additional gain stages.
PCB layout should keep input and feedback connections short and route them away from high-current switching nodes. Decoupling capacitors should be placed close to the power pins, while the unused amplifier in any unused channel must be configured according to the Texas Instruments LM324K datasheet rather than left floating. The 14-pin SOIC footprint simplifies replacement on compatible LM324NS-style boards.
This product record combines manufacturer specifications, package and ordering information, drop-in candidate analysis, comparison parameters, and practical PCB guidance. It helps engineers evaluate the LM324KNSR for general-purpose analog designs and identify whether a same-footprint LM324-family device is appropriate when supply voltage, temperature grade, or sourcing requirements change.
Аналоги без доработки для LM324KNSR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM324KNSR (тот же форм-фактор и посадочное место) — отличается по Package, Supply Configuration, Input Offset Voltage, Maximum Supply Voltage, Amplifier Type.
LM324ANSR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM324ADR
✅ Прямая заменаУточнить цену
Открыть даташит →LM324DR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM2902NSR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM324KNS
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM324KNSR Максимальные параметры и электрические характеристики
| Amplifier Count | 4 independent amplifiers |
| Product Type | Quad general-purpose operational amplifier |
| Maximum Supply Voltage | 30 V |
| Supply Configuration | Single or split supply |
| Gain-Bandwidth Product | 1.2 MHz |
| Improved ESD Protection | 2 kV |
| Диапазон рабочих температур | 0 °C to 70 °C |
| Корпус | 14-pin SOIC (NS, SOP) |
| Число выводов | 14 pins |
| Тип монтажа | Surface mount |
| Shipping Form | NSR ordering code |
Руководство по цоколевке LM324KNSR в корпусе 14-pin soic (ns, sop)
Цоколевка для LM324KNSR (корпус 14-pin soic (ns, sop)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для LM324KNSR.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM324KNSR подходит для 6 применениеs: General-Purpose Sensor Signal Conditioning, Audio Preamplification, Active Filtering and Control Loops, Power Supply Current Measurement, Instrumentation Buffering, Interface and Level Conditioning.
General-Purpose Sensor Signal Conditioning
The LM324KNSR fits four-channel sensor conditioning because it integrates four independent, frequency-compensated amplifiers with 1.2 MHz gain-bandwidth bandwidth in one 14-pin SOIC package. Each amplifier can scale a low-level sensor signal or drive a feedback network before conversion. The 30 V maximum supply rating supports 5 V, 12 V, and other supply arrangements, while the 0 to 70 °C range targets commercial equipment. Place supply-decoupling capacitors near the package and keep high-impedance input traces short to reduce noise pickup and imbalance error.
Рекомендуется
Audio Preamplification
The LM324KNSR can provide the general-purpose gain stages used around audio sources because each amplifier is frequency compensated and supports single or split supplies. The 1.2 MHz gain-bandwidth bandwidth is sufficient for many low-to-moderate-bandwidth preamplifier and mixer stages, while four amplifiers allow balanced input handling or two stereo channels in one package. The 2 kV improved ESD rating also benefits equipment exposed to electrostatic discharge. Designers should verify output swing and bandwidth at the intended signal amplitude instead of assuming the full 30 V supply can appear at the output.
Рекомендуется
Active Filtering and Control Loops
The four channels in LM324KNSR are useful for active filter and feedback-control implementations where several related amplifier stages share the same supply. The 1.2 MHz gain-bandwidth bandwidth provides a defined performance point for evaluating closed-loop filter response and control-loop compensation. Because the amplifiers are independent, separate filters or a multistage servo loop can be implemented in one 14-pin SOIC. Use the Texas Instruments LM324K gain and phase characteristics to select resistor and capacitor values, and keep sensitive summing nodes away from power-supply and switching traces.
Рекомендуется
Power Supply Current Measurement
LM324KNSR can form the transimpedance and buffering stages of a current-measurement system because it combines four independent amplifiers with a 30 V maximum supply rating. A shunt amplifier, differential sensing stage, output filter, and monitor amplifier can share one package when their signal ranges and bandwidth requirements suit the 1.2 MHz device. The commercial 0 to 70 °C range is appropriate for room-temperature test equipment. Confirm input offset, input bias current, common-mode range, and output swing at the actual shunt voltage before relying on accuracy at microampere or milliampere levels.
Рекомендуется
Instrumentation Buffering
The LM324KNSR is suitable for instrumentation buffering when the design needs several high-input-impedance buffer or gain functions rather than a single precision amplifier. Its four independent channels can isolate sensor outputs, buffer reference voltages, and amplify intermediate signals within one 14-pin SOIC package. The 30 V rating is useful for powered laboratory and industrial control boards, while the 1.2 MHz bandwidth supports many low-frequency measurement paths. The 2 kV improved ESD protection is relevant for bench equipment, although system-level grounding and connector protection still determine real transient immunity.
Рекомендуется
Interface and Level Conditioning
LM324KNSR can condition logic-level, analog-reference, or low-speed communications signals when a board needs several op-amp channels with common supply connections. Single- or split-supply operation supports both grounded and offset signal paths, and the four-amplifier configuration can implement buffering, comparison, gain, and active filtering in parallel. The 1.2 MHz bandwidth is more than adequate for many low-speed interface tasks but should be checked against edge-rate requirements. Route outputs away from fast digital nets and use local supply bypassing to maintain predictable behavior in mixed-signal equipment.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM324KNSR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM324ANSR | LM324ADR | LM324DR | LM2902NSR | LM324KNS |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC (NS) | 14-SOIC (NS) | 14-SOIC | 14-SOIC | 14-SOIC (NS) | 14-SOIC (NS) |
| Amplifier Count | 4 independent amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
| Special Feature | Improved ESD protection | LM324A family | LM324A family | Legacy LM324 family | LM2902 family | Improved ESD protection |
Ключевые отличия
- Improved electrostatic-discharge protection in the selected LM324K family (против LM324ADR)
- Commercial-temperature ordering profile (против LM324DR)
- Same LM324K family with direct NS-footprint reuse (против LM324KNS)
- Four independent amplifiers in one package (против LM2902NSR)
Заметки по проектированию
Place the supply-bypass capacitors immediately beside pins 4 and 11, with short, low-inductance connections to the ground plane. Keep each amplifier's noninverting input, inverting input, and feedback components close together and away from switching nodes. The four amplifiers share supply pins, so a noisy load on one channel can couple through the common supply network; isolate high-current outputs and use local decoupling when necessary.
Treat high-impedance input traces as sensitive nodes because input offset and bias current establish the practical accuracy of a general-purpose amplifier stage. Minimize leakage from PCB contamination, flux residue, humidity, and nearby high-impedance sources. Where the 1.2 MHz device operates near its bandwidth limit, keep feedback loops compact and verify both magnitude and phase margin using the gain-bandwidth and output-capability information in the LM324K datasheet.
Do not assume that the 30 V maximum supply rating permits a 30 V output or unrestricted input range. The valid common-mode input range and output swing depend on the selected supply and output conditions. Likewise, configure every unused amplifier as a stable stage rather than allowing its input to float. Before replacing LM324KNSR with LM324ANSR, LM324ADR, LM324DR, LM2902NSR, or LM324KNS, verify the complete operating limits and pin description for the exact ordering suffix.
Информация о соответствии
No explicit LM324KNSR compliance declarations or AEC-Q100 qualification were identified. A commercial 0 to 70 °C operating-temperature range is not, by itself, evidence of AEC-Q100 qualification.