LTC2122IUK - Dual 14-Bit 170Msps ADC w/ JESD204B | ADI
Артикул: LTC2122IUK ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $102.5 | $102,50 |
| 10 | $95.36 | $953,60 |
| 100 | $89.2 | $8.920,00 |
| 500 | $85.1 | $42.550,00 |
| 1.000 | $81.5 | $81.500,00 |
LTC2122IUK Обзор
A pipelined ADC architecture uses a high-speed, multi-stage switched-capacitor structure with digital error correction, allowing the LTC2122 to maintain 14-bit linearity up to 170 Msps. Dual-channel simultaneous sampling eliminates inter-channel skew, critical for MIMO receivers, phased-array radar, and diversity antenna systems. The JESD204B serial interface transports the digitized data using up to 4 lanes with 8b/10b encoding, deterministic latency, and embedded clock recovery, which minimizes board routing complexity compared to LVDS parallel interfaces. An on-chip SYSREF input supports deterministic latency for multi-device synchronization in large-channel-count systems.
The LTC2122 targets demanding communications applications including LTE and multi-carrier GSM base-station receivers, software-defined radio, cable infrastructure head-end digitization, and high-density MIMO systems. Its 70 dBFS SNR and 90 dBFS SFDR at 170 Msps enable the receiver to digitize a 60 MHz LTE carrier with margin for adjacent-channel blocker rejection. The 1.25 GHz input bandwidth also supports undersampling of L-band and S-band signals, reducing the number of downconversion stages in the signal chain. The 48-QFN (7x7) exposed-pad package provides a low thermal resistance path, allowing operation across the industrial -40C to +85C temperature range without derating at the rated sample rate.
For PCB layout, place 0.1uF and 10nF ceramic decoupling capacitors within 5 mm of each supply pin, with the exposed pad soldered to a continuous ground plane. Route the JESD204B serialized lanes as length-matched 100 ohm differential pairs with controlled 50 ohm single-ended impedance, and keep AC-coupled capacitors within 5 mm of the transmitter pins to meet the JESD204B eye-mask specification.
Аналоги без доработки для LTC2122IUK — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2122IUK (тот же форм-фактор и посадочное место) — отличается по RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2122CUK#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2122IUK#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2122IUK#TRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2122IUK Максимальные параметры и электрические характеристики
| Разрешение | 14 bit |
| Number of Channels | 2 (simultaneous sampling) |
| Sample Rate | 170 Msps |
| Architecture | Pipelined |
| Input Bandwidth | 1.25 GHz |
| SNR | 70 dBFS |
| SFDR | 90 dBFS |
| Digital Interface | JESD204B (subclass 1) |
| Number of JESD204B Lanes | Up to 4 |
| Analog Supply Voltage | 1.7 V to 1.9 V (1.8 V nominal) |
| Input Type | Differential |
| Рабочая температура | -40C to +85C (industrial) |
| Корпус | 48-QFN (7x7 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов LTC2122IUK
| Контакт 1 | AIN+ — Channel A differential analog input positive |
| Контакт 2 | AIN- — Channel A differential analog input negative |
| Контакт 3 | VCM_A — Channel A common-mode voltage output |
| Контакт 4 | GND — Analog ground |
| Контакт 5 | VA — 1.8V analog supply |
| Контакт 6 | GND — Analog ground |
| Контакт 7 | VA — 1.8V analog supply |
| Контакт 8 | GND — Analog ground |
| Контакт 9 | ENC+ — Differential clock input positive |
| Контакт 10 | ENC- — Differential clock input negative |
| Контакт 11 | GND — Clock ground |
| Контакт 12 | VA — 1.8V analog supply |
| Контакт 13 | GND — Analog ground |
| Контакт 14 | VA — 1.8V analog supply |
| Контакт 15 | BIN- — Channel B differential analog input negative |
| Контакт 16 | BIN+ — Channel B differential analog input positive |
| Контакт 17 | VCM_B — Channel B common-mode voltage output |
| Контакт 18 | GND — Analog ground |
| Контакт 19 | VA — 1.8V analog supply |
| Контакт 20 | GND — Analog ground |
| Контакт 21 | VD — Digital supply |
| Контакт 22 | GND — Digital ground |
| Контакт 23 | VD — Digital supply |
| Контакт 24 | GND — Digital ground |
| Контакт 25 | DOUT0+ — JESD204B serial lane 0 positive |
| Контакт 26 | DOUT0- — JESD204B serial lane 0 negative |
| Контакт 27 | GND — Serializer ground |
| Контакт 28 | DOUT1+ — JESD204B serial lane 1 positive |
| Контакт 29 | DOUT1- — JESD204B serial lane 1 negative |
| Контакт 30 | GND — Serializer ground |
| Контакт 31 | DOUT2+ — JESD204B serial lane 2 positive |
| Контакт 32 | DOUT2- — JESD204B serial lane 2 negative |
| Контакт 33 | GND — Serializer ground |
| Контакт 34 | DOUT3+ — JESD204B serial lane 3 positive |
| Контакт 35 | DOUT3- — JESD204B serial lane 3 negative |
| Контакт 36 | GND — Serializer ground |
| Контакт 37 | SYREF+ — JESD204B SYSREF input positive |
| Контакт 38 | SYREF- — JESD204B SYSREF input negative |
| Контакт 39 | GND — Digital ground |
| Контакт 40 | SCK — Serial configuration clock input |
| Контакт 41 | SDI — Serial configuration data input |
| Контакт 42 | SDO — Serial configuration data output |
| Контакт 43 | CSN — Serial configuration chip select (active low) |
| Контакт 44 | RESETN — Reset input (active low) |
| Контакт 45 | PDN — Power down input (active high) |
| Контакт 46 | GND — Digital ground |
| Контакт 47 | VD — Digital supply |
| Контакт 48 | GND — Digital ground |
| Контакт 49 | EPAD — Exposed pad - thermal and ground (must be soldered to PCB ground plane) |
Типичное применение
LTC2122IUK подходит для 6 применениеs: LTE Multi-Carrier Base Station Receiver, Software Defined Radio (SDR) Platforms, Phased-Array Radar Signal Digitization, Cable Infrastructure Head-End Digitization, MIMO Wireless Test and Measurement, Medical Ultrasound Imaging Receivers.
LTE Multi-Carrier Base Station Receiver
The LTC2122IUK is ideally suited for LTE and multi-carrier GSM base-station receiver applications where dual-channel simultaneous sampling at 170 Msps is required. Its 70 dBFS SNR and 90 dBFS SFDR provide the dynamic range needed to digitize a 60 MHz LTE carrier with adjacent-channel blocker rejection margin, while the 1.25 GHz input bandwidth supports direct IF sampling of L-band signals. The JESD204B serial interface with SYSREF synchronization allows multiple LTC2122IUK devices to be ganged together for multi-sector or massive-MIMO antenna arrays, with deterministic latency simplifying baseband DSP timing. The dual simultaneous-sampling channels eliminate inter-channel skew for receiver diversity and beamforming applications, and the 48-QFN (7x7) exposed-pad package provides adequate thermal performance for continuous full-rate operation in densely populated base-station line cards.
Рекомендуется
Software Defined Radio (SDR) Platforms
In wideband software-defined radio platforms, the LTC2122IUK digitizes I and Q baseband signals simultaneously at 170 Msps with 14-bit resolution. The dual-channel architecture maps directly to direct-conversion I/Q receiver front-ends, eliminating the need for separate baseband ADCs. The 1.25 GHz input bandwidth supports undersampling of HF, VHF, and UHF signals, allowing the SDR to cover multiple frequency bands with a single fixed anti-alias filter. The JESD204B interface connects the LTC2122IUK directly to FPGAs (Xilinx 7-series, Intel Cyclone V) with a small number of high-speed serial lanes, freeing board space for RF front-end components. The 70 dBFS SNR preserves signal-to-noise ratio for weak signal demodulation, while 90 dBFS SFDR prevents intermodulation distortion from degrading adjacent-channel reception.
Рекомендуется
Phased-Array Radar Signal Digitization
The dual-channel simultaneous sampling and JESD204B SYSREF synchronization make the LTC2122IUK a strong fit for phased-array radar sub-array digitization. Each sub-array tile digitizes two antenna channels at 170 Msps, and multiple LTC2122IUK devices are time-aligned via the SYSREF input, providing deterministic sample-phase alignment across a 64-element or larger antenna array. The 1.25 GHz input bandwidth supports L-band and S-band radar IF sampling, and the 70 dBFS SNR preserves the dynamic range needed to detect small targets in clutter. The 48-QFN (7x7) package with exposed pad enables dense placement on radar tile boards, while the JESD204B interface transports sample data to a central FPGA beamformer over a few serial lanes. The industrial -40C to +85C temperature range supports outdoor military and aerospace radar installations.
Рекомендуется
Cable Infrastructure Head-End Digitization
Cable television head-end equipment digitizes downstream QAM and OFDM channels directly at IF, and the LTC2122IUK's 170 Msps sample rate covers an 80 MHz upstream DOCSIS 3.1 channel block with margin. The 70 dBFS SNR and 90 dBFS SFDR support the carrier-to-noise and modulation-error-ratio requirements of 1024-QAM and 4096-QAM downstream modulation. The dual channels allow one LTC2122IUK to digitize both upstream and downstream spectrum segments simultaneously, reducing BOM cost per head-end channel. The 1.25 GHz input bandwidth supports direct sampling of L-band cable IF, and the JESD204B interface connects to cable modem termination system (CMTS) ASICs and FPGAs. The 48-QFN exposed-pad package handles the thermal load of continuous 170 Msps operation in enclosed head-end rack equipment.
Рекомендуется
MIMO Wireless Test and Measurement
Wireless test and measurement instruments use the LTC2122IUK to digitize multiple antenna channels simultaneously for 4G/5G MIMO receiver test. The dual simultaneous-sampling channels allow a single LTC2122IUK to capture two streams of a 4x4 MIMO downlink, with matched gain and phase response between channels. The 170 Msps sample rate handles 100 MHz 5G NR signal bandwidth, and the 70 dBFS SNR supports EVM measurements down to -45 dB at the digitizer. The JESD204B interface streams samples to an FPGA-based real-time signal processor for EVM, ACLR, and spectral analysis. The 1.25 GHz input bandwidth supports over-the-air testing of millimeter-wave 5G systems after external downconversion, and the 48-QFN (7x7) package provides 2-channel density in compact production test rack form factors.
Рекомендуется
Medical Ultrasound Imaging Receivers
Medical ultrasound imaging systems use the LTC2122IUK to digitize the I and Q quadrature outputs of the receive beamformer, with 14-bit resolution and 170 Msps sample rate supporting high-frequency linear and phased-array probes. The dual simultaneous-sampling channels reduce the channel-to-channel timing skew that would otherwise degrade beamforming resolution, and the 70 dBFS SNR preserves the dynamic range needed to visualize small tissue structures. The JESD204B interface transports the digitized RF data to a beamforming FPGA over a small number of serial lanes, reducing PCB density in 64-channel and 128-channel ultrasound carts. The 1.25 GHz input bandwidth supports up to 50 MHz probe frequency with harmonic imaging, and the 48-QFN (7x7) package enables compact portable ultrasound designs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2122IUK — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2122CUK#PBF | LTC2122IUK#PBF | LTC2122IUK#TRPBF |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Resolution | 14 bit | 14 bit | 14 bit | 14 bit |
| Sample Rate | 170 Msps | 170 Msps | 170 Msps | 170 Msps |
| Number of Channels | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) | 2 (simultaneous) |
| Interface | JESD204B (4 lanes) | JESD204B (4 lanes) | JESD204B (4 lanes) | JESD204B (4 lanes) |
| SNR | 70 dBFS | 70 dBFS | 70 dBFS | 70 dBFS |
| Operating Temperature | -40C to +85C | 0C to +70C (commercial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| Ordering Code Suffix | IUK (industrial grade) | CUK#PBF (commercial, Pb-free) | IUK#PBF (industrial, Pb-free) | IUK#TRPBF (industrial, Pb-free, T&R) |
Ключевые отличия
- Industrial temperature grade for harsh environments (против LTC2122CUK#PBF)
- Lead-free (Pb-free) ordering code with identical performance (против LTC2122IUK (base MPN))
- Tape-and-reel packaging for high-volume production (против LTC2122IUK#PBF (tray))
Заметки по проектированию
Place 0.1uF and 10nF ceramic decoupling capacitors within 5 mm of each VA and VD supply pin. The exposed pad (pin 49) must be soldered to a continuous ground plane to provide the low thermal resistance path specified in the datasheet. Without proper exposed-pad soldering, junction temperature can rise and degrade AC performance. The JESD204B serial data lanes should be routed as 100 ohm differential pairs with length matching within 0.5 mm to maintain lane-to-lane skew compliance.
Keep the differential analog inputs (AIN+/AIN-, BIN+/BIN-) as short as possible, with controlled 100 ohm differential impedance. Place the input common-mode bypass capacitor (typically 0.1uF) within 5 mm of the VCM_A and VCM_B pins. Separate the analog input traces from the JESD204B digital output traces to minimize digital noise coupling into the analog front-end. Use a ground cutout beneath the input balun network if used, to reduce parasitic capacitance.
Do not exceed the maximum analog supply voltage of 1.9V - the LTC2122 is not 3.3V tolerant. Ensure the ENC+/ENC- differential clock meets the JESD204B input clock specification (typically 0.5V to 1.5Vpp differential) - an improper clock amplitude will cause sub-optimal SNR and SFDR. After power-up, the RESETN pin must be held low for at least 1us before being released, to ensure proper initialization of the digital logic and JESD204B serializer.
Информация о соответствии
RoHS compliant per Analog Devices product page. Pb-free manufacturing indicated by #PBF suffix. Not AEC-Q100 qualified - this part targets communications and instrumentation, not automotive.