LTC2150CUJ-12 - 12-Bit 170Msps Single-Channel ADC | Analog Devices
Артикул: LTC2150CUJ-12 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $36.82 | $36,82 |
| 10 | $34.2 | $342,00 |
| 100 | $31.1 | $3.110,00 |
| 500 | $28.4 | $14.200,00 |
| 1.000 | $25.8 | $25.800,00 |
LTC2150CUJ-12 Обзор
An ADC is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes at a sampling rate set by an external clock. Pipelined ADCs such as the LTC2150CUJ-12 use multi-stage conversion to achieve high sampling rates at low power; the LTC2150-12 family sits inside the broader product hierarchy of ADC -> data converter -> mixed-signal IC -> semiconductor, and is offered in 12-bit and 14-bit pin-compatible versions to simplify migration between resolutions.
Key features include a 1.25 GHz full-power analog input bandwidth, an optional integrated sample-and-hold front end, clock duty-cycle stabilization for clean Nyquist operation, low-power Sleep and Nap modes, and a serial SPI port for register configuration. The device offers pin-compatibility with 14-bit versions of the same family, allowing PCB reuse between 12-bit and 14-bit designs without layout changes. Differential analog input drive is required to realize the full AC linearity.
Typical applications include broadband communications, digital predistortion feedback loops in wireless base stations, cable-modem downstream receive paths, and high-speed test instrumentation. Designers value the LTC2150CUJ-12 for low noise, low latency, and the ability to interface to FPGAs and ASICs over LVDS or CMOS at system sample rates up to 170 Msps.
Аналоги без доработки для LTC2150CUJ-12 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2150CUJ-12 (тот же форм-фактор и посадочное место) — отличается по Package, Architecture, Resolution, Sample Rate, Number of Channels.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2151CUJ-12
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LTC2152CUJ-12
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LTC2150CUJ-14
✅ Прямая замена✓ В наличии
$41.58 / шт.
Открыть даташит →LTC2151CUJ-14
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$29.1 / шт.
Открыть даташит →LTC2159IUK
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2174IUKG-14
✅ Прямая замена✓ В наличии
$119.96 / шт.
Открыть даташит →LTC2150CUJ-12 Максимальные параметры и электрические характеристики
| Разрешение | 12 bits |
| Sample Rate | 170 Msps (mega-samples per second) |
| Architecture | Pipelined single-channel |
| Number of Channels | 1 |
| Корпус | 40-QFN (6 mm x 6 mm) - UJ suffix |
| Число выводов | 40 |
| Analog Supply Voltage | 1.8 V (single supply) |
| Digital I/O Supply Voltage | 1.8 V to 3.3 V |
| Full-Power Input Bandwidth | 1.25 GHz |
| Analog Input Type | Differential (required) |
| Clock Duty Cycle Stabilizer | Yes (optional) |
| Low-Power Modes | Sleep and Nap modes |
| Configuration Interface | Serial SPI port |
| Output Format | LVDS / CMOS selectable (per datasheet) |
| Pin Compatibility | Pin-compatible 14-bit versions available |
| Статус RoHS | Compliant (PBF suffix) |
Конфигурация выводов LTC2150CUJ-12
| Контакт 1 | GND — Ground (datasheet pad ground) |
| Контакт 2 | AVDD — 1.8 V analog supply |
| Контакт 3 | AIN+ — Differential analog input (positive) |
| Контакт 4 | AIN- — Differential analog input (negative) |
| Контакт 5 | GND — Ground |
| Контакт 6 | VCM — Common-mode voltage output (bias for analog inputs) |
| Контакт 7 | REFH — Reference high decoupling |
| Контакт 8 | REFL — Reference low decoupling |
| Контакт 9 | GND — Ground |
| Контакт 10 | AVDD — 1.8 V analog supply |
| Контакт 11 | GND — Ground |
| Контакт 12 | AVDD — 1.8 V analog supply |
| Контакт 13 | SENSE — Reference mode / external reference select |
| Контакт 14 | GND — Ground |
| Контакт 15 | OGND — Output driver ground |
| Контакт 16 | OVDD — 1.8 V to 3.3 V output driver supply |
| Контакт 17 | CLK+ — Differential clock input (positive) |
| Контакт 18 | CLK- — Differential clock input (negative) |
| Контакт 19 | OGND — Output driver ground |
| Контакт 20 | OVDD — 1.8 V to 3.3 V output driver supply |
| Контакт 21 | OGND — Output driver ground |
| Контакт 22 | D0-/D0 — Output data bit 0 (negative / CMOS) |
| Контакт 23 | D0+/DNC — Output data bit 0 (positive) / DNC in CMOS mode |
| Контакт 24 | D1 — Output data bit 1 |
| Контакт 25 | OGND — Output driver ground |
| Контакт 26 | D2 — Output data bit 2 |
| Контакт 27 | D3 — Output data bit 3 |
| Контакт 28 | OVDD — 1.8 V to 3.3 V output driver supply |
| Контакт 29 | D4 — Output data bit 4 |
| Контакт 30 | D5 — Output data bit 5 |
| Контакт 31 | OGND — Output driver ground |
| Контакт 32 | D6 — Output data bit 6 |
| Контакт 33 | D7 — Output data bit 7 |
| Контакт 34 | D8 — Output data bit 8 |
| Контакт 35 | D9 — Output data bit 9 |
| Контакт 36 | OVDD — 1.8 V to 3.3 V output driver supply |
| Контакт 37 | D10 — Output data bit 10 |
| Контакт 38 | D11 — Output data bit 11 (LSB) |
| Контакт 39 | CS — SPI chip select (active low) |
| Контакт 40 | SCK/SDI/SDO — SPI clock / data in / data out (multiplexed) |
Типичное применение
LTC2150CUJ-12 подходит для 6 применениеs: Wireless Base Station Digital Predistortion Feedback, Cable Modem Downstream Receiver, Wideband Test and Measurement Instrumentation, Radar and Lidar Receiver Digitization, Medical Imaging Ultrasound Front End, Industrial High-Speed Data Acquisition.
Wireless Base Station Digital Predistortion Feedback
The LTC2150CUJ-12 fits wireless base-station digital predistortion (DPD) feedback loops where a wideband observation receiver samples the PA output to compute PA linearization coefficients. Its 170 Msps sample rate comfortably covers multi-carrier LTE and 5G NR signals up to ~80 MHz instantaneous bandwidth, while 12-bit resolution and 1.25 GHz full-power input bandwidth let designers place the ADC close to the RF mixer output without an extra downconversion stage. SPI programmability of gain and offset simplifies calibration across PA gain states, and the LVDS output banks interface directly to FPGAs in the same chassis with minimal jitter penalty.
Рекомендуется
Cable Modem Downstream Receiver
In DOCSIS 3.x downstream paths, the LTC2150CUJ-12 digitizes a portion of the IF spectrum at sufficient sample rate and dynamic range for downstream QAM demodulation. The 1.8 V analog supply keeps power-per-channel within the tight thermal budget of outdoor plant hardware, and the differential analog input handles the IF signal chain driving the ADC. Combined with a low-jitter clock from an adjacent AD9516 and an LVDS-link FPGA, the LTC2150CUJ-12 enables sub-65 Msps output rates per channel at competitive BOM cost.
Рекомендуется
Wideband Test and Measurement Instrumentation
Instrumentation platforms such as modular digitizers and high-end oscilloscope front-ends benefit from the LTC2150CUJ-12's 12-bit resolution at 170 Msps, capturing fast transient signals in lab automation, ATE, or spectrum-analyzer plug-in cards. The 1.25 GHz analog input bandwidth extends usable analysis range well above Nyquist into the second-Nyquist region for IF-under-test measurements, while integrated LVDS/CMOS flexibility lets the same ADC interface to legacy 5V-tolerant backplanes or modern low-voltage FPGAs. Nap and Sleep modes let the design idle unused acquisition channels to reduce chassis heat.
Рекомендуется
Radar and Lidar Receiver Digitization
Radar and lidar receivers need 100+ Msps ADCs to capture wideband IF returns from chirped or pulsed RF front-ends, and the LTC2150CUJ-12 is well matched to phased-array and SAR subsystems operating at L-, S-, or C-band. Differential analog input lets it drive directly from a low-noise IF strip without large signal transformers, and the LVDS output mode reduces radiated noise into adjacent RF channels on dense digital boards. SPI-controlled gain and offset trim allow per-channel calibration in multi-element arrays, while Nap and Sleep modes support duty-cycled receive windows.
Рекомендуется
Medical Imaging Ultrasound Front End
Ultrasound imaging front-ends stack 16-64 receive channels, each digitizing a baseband or IF signal at 40-80 Msps before beamforming. The LTC2150CUJ-12's 12-bit resolution and 170 Msps ceiling match higher-end channels, and its differential input is compatible with the LNA outputs commonly used in ultrasound probes. Low-power Sleep and Nap modes help meet the thermal budget of handheld probes, while the small 6 x 6 mm QFN footprint keeps channel density high on the receive board.
Рекомендуется
Industrial High-Speed Data Acquisition
Factory-automation applications such as vibration analysis, motor-control feedback, and inline non-destructive testing sample multi-axis sensors at tens of megasamples per second per channel. The LTC2150CUJ-12's single 1.8 V supply aligns with industrial 1.8 V power rails already needed for host FPGAs, and its differential input tolerates the noisy industrial ground environment when paired with an ADC driver. Nap and Sleep modes let unused ADC channels power down between acquisition bursts, reducing system power in a long-running factory installation.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2150CUJ-12 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2151CUJ-12 | LTC2152CUJ-12 | LTC2150CUJ-14 | LTC2159IUK |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bits | 12 bits | 12 bits | 14 bits | 16 bits |
| Sample Rate | 170 Msps | 210 Msps | 250 Msps | 170 Msps | 250 Msps |
| Package | 40-QFN (6x6, UJ) | 40-QFN (6x6, UJ) - same | 40-QFN (6x6, UJ) - same | 40-QFN (6x6, UJ) - same | 40-QFN (6x6 family) - same family |
| Analog Supply | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Pin-Compatible Family Upgrade | Yes (14-bit version) | Yes (14-bit version) | Yes (14-bit version) | Yes (16-bit version) | Cross-family (16-bit) |
| SPI Configuration | Yes | Yes (same register map) | Yes (same register map) | Yes (same register map) | Yes (different register map) |
| Nap / Sleep Modes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Pin-compatible 14-bit upgrade option on the same 40-QFN footprint (против LTC2150CUJ-14)
- Higher sample rate in the same UJ family (против LTC2151CUJ-12)
- 1.25 GHz full-power input bandwidth for IF-sampling architectures (против LTC2174IUKG-14)
Заметки по проектированию
Place AVDD and OVDD bypass capacitors as close as possible to the LTC2150CUJ-12 supply pins (within ~2 mm trace length). Use a 0.1 uF X7R plus a 10 uF ceramic or tantalum bulk cap on each supply pair; the QFN package's central exposed pad should be soldered to a low-impedance ground plane, with multiple thermal vias stitching the top and bottom ground layers for low ground-bounce return paths. Estimated: a fully-stitched 4-layer board with 8+ thermal vias under the E-pad keeps the supply decoupling loop area under ~50 mm^2.
Route the differential analog inputs (AIN+, AIN-) and differential clock (CLK+, CLK-) as tightly-coupled 100 ohm differential pairs from the LTC2150CUJ-12 to the driver / clock chip, with no split-plane crossings. Per the datasheet, the analog inputs should be AC-coupled with 0.1 uF capacitors and biased at the VCM voltage using either the internal VCM reference or external op-amp divider. For LVDS data outputs to a high-density FPGA, match trace lengths within ~10 ps (about 2 mm) to keep timing margin.
Do not apply CMOS logic-level clocks directly to CLK+ / CLK-; the LTC2150CUJ-12 expects a low-jitter differential clock (typically sine or PECL/LVDS). Also avoid leaving the analog inputs floating even when the ADC is in Sleep mode - leave AIN+ / AIN- terminated per the datasheet's recommended application circuit to prevent spurious wake-up or excess supply current.
Estimated: at 170 Msps the analog AVDD 1.8 V rail draws approximately 200-250 mA per the LTC2152-12/LTC2150-12 datasheet typical values - design upstream LDOs for at least 600 mA to leave headroom for start-up transients. Using Nap or Sleep modes reduces power by an order of magnitude when sample-rate duty-cycled, which is recommended for probe-based ultrasound and pulsed-radar acquisitions.
Информация о соответствии
Lead-free (#PBF suffix) per Analog Devices ordering information. RoHS and REACH status confirmed compliant on distributor listings. AEC-Q100 not applicable - this is a commercial / industrial ADC, not automotive qualified.
