LTC2158CUP-14 - Dual 14-Bit 310Msps ADC | Analog Devices
Артикул: LTC2158CUP-14 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $65.4 | $65,40 |
| 10 | $58.9 | $589,00 |
| 100 | $52.1 | $5.210,00 |
| 500 | $46.85 | $23.425,00 |
| 1.000 | $41.2 | $41.200,00 |
LTC2158CUP-14 Обзор
A pipelined ADC is a multi-step converter architecture that processes one conversion stage per clock cycle, allowing very high sample rates (hundreds of Msps to Gsps) while keeping per-stage comparator requirements modest. Within the broader signal-chain hierarchy, the LTC2158CUP-14 sits as an analog-to-digital converter -> data converter -> mixed-signal IC -> semiconductor. Its dual simultaneous-sampling channels make it a member of the high-speed pipeline-ADC family targeted at communications infrastructure, radar, and instrumentation.
Key features include dual simultaneous-sampling 14-bit 310 Msps conversion per channel, 68.8 dB SNR and 88 dB SFDR for wide dynamic-range capture, 1.25 GHz analog input bandwidth for IF sampling, 355 mA supply current from a 1.7 V to 1.9 V analog/digital supply, and an exposed-pad QFN-64 (9x9) package for low thermal resistance. The integrated input common-mode bias simplifies transformer or op-amp driver interfaces.
The device uses a multi-stage differential pipeline core with on-chip reference and sample-and-hold, supporting CMOS or DDR LVDS output formats for flexible FPGA/ASIC capture. LVDS outputs simplify board layout and reduce digital switching noise coupling into the analog front end.
Typical applications include communications receivers, cellular base-station digitizers, radar and phased-array signal processing, test and measurement instrumentation, and high-performance imaging. Dual simultaneous channels allow I/Q capture or diversity reception from a single converter IC.
When designing with the LTC2158CUP-14, decouple each analog and digital supply pin individually, route the LVDS outputs with 100 ohm differential impedance, and provide a low-jitter clock to CLK+ and CLK- to preserve SNR at full rate. The exposed pad must be soldered to a continuous ground plane for thermal dissipation and electrical reference.
This page synthesizes verified distributor pricing, drop-in QFN-64 same-family alternatives, and practical PCB/decoupling design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для LTC2158CUP-14 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2158CUP-14 (тот же форм-фактор и посадочное место) — отличается по Package, Resolution, SNR, Operating Temperature Range, Sampling Rate.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2158IUP-14
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2157CUP-14
✅ Прямая замена✓ В наличии
$132.4 / шт.
Открыть даташит →LTC2156IUP-14
✅ Прямая замена✓ В наличии
$134.1 / шт.
Открыть даташит →LTC2155CUP-12
✅ Прямая замена✓ В наличии
$44.25 / шт.
Открыть даташит →LTC2158CUP-14 Максимальные параметры и электрические характеристики
| Разрешение | 14 bit |
| Number of Channels | 2 (simultaneous sampling) |
| Частота дискретизации | 310 Msps per channel |
| Architecture | Pipelined |
| Input Bandwidth | 1.25 GHz |
| SNR | 68.8 dB |
| SFDR | 88 dB |
| Ток потребления | 355 mA |
| Analog Supply Voltage | 1.7 V to 1.9 V |
| Digital Output Format | CMOS / DDR LVDS |
| Корпус | 64-QFN (9x9 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Input Type | Differential |
| Статус RoHS | Compliant (per #PBF suffix) |
Конфигурация выводов LTC2158CUP-14
| Контакт 1 | AIN1+ — Channel 1 differential analog input positive |
| Контакт 2 | AIN1- — Channel 1 differential analog input negative |
| Контакт 3 | VCM1 — Channel 1 common-mode voltage bias |
| Контакт 4 | AGND — Analog ground |
| Контакт 5 | AVDD — Analog supply (1.8 V nominal) |
| Контакт 6 | AVDD — Analog supply (1.8 V nominal) |
| Контакт 7 | REF — Reference voltage decoupling |
| Контакт 8 | AGND — Analog ground |
| Контакт 9 | SENSE — Reference mode select |
| Контакт 10 | REFT — Top reference decoupling |
| Контакт 11 | REFB — Bottom reference decoupling |
| Контакт 12 | AGND — Analog ground |
| Контакт 13 | AIN2+ — Channel 2 differential analog input positive |
| Контакт 14 | AIN2- — Channel 2 differential analog input negative |
| Контакт 15 | VCM2 — Channel 2 common-mode voltage bias |
| Контакт 16 | AGND — Analog ground |
| Контакт 17 | AVDD — Analog supply (1.8 V nominal) |
| Контакт 18 | AVDD — Analog supply (1.8 V nominal) |
| Контакт 19 | CLK+ — Differential clock input positive |
| Контакт 20 | CLK- — Differential clock input negative |
| Контакт 21 | AGND — Analog ground |
| Контакт 22 | OGND — Output driver ground |
| Контакт 23 | OVDD — Output driver supply (1.8 V nominal) |
| Контакт 24 | OVDD — Output driver supply (1.8 V nominal) |
| Контакт 25 | D0_1 — Channel 1 LVDS/CMOS output bit 0 (LSB) |
| Контакт 26 | D1_1 — Channel 1 output bit 1 |
| Контакт 27 | D2_1 — Channel 1 output bit 2 |
| Контакт 28 | D3_1 — Channel 1 output bit 3 |
| Контакт 29 | D4_1 — Channel 1 output bit 4 |
| Контакт 30 | D5_1 — Channel 1 output bit 5 |
| Контакт 31 | D6_1 — Channel 1 output bit 6 |
| Контакт 32 | D7_1 — Channel 1 output bit 7 |
| Контакт 33 | D8_1 — Channel 1 output bit 8 |
| Контакт 34 | D9_1 — Channel 1 output bit 9 |
| Контакт 35 | D10_1 — Channel 1 output bit 10 |
| Контакт 36 | D11_1 — Channel 1 output bit 11 |
| Контакт 37 | D12_1 — Channel 1 output bit 12 |
| Контакт 38 | D13_1 — Channel 1 output bit 13 (MSB) |
| Контакт 39 | DCLK1 — Channel 1 DDR clock output |
| Контакт 40 | FR_N_1 — Channel 1 frame indicator (active low) |
| Контакт 41 | OGND — Output driver ground |
| Контакт 42 | OVDD — Output driver supply (1.8 V nominal) |
| Контакт 43 | D0_2 — Channel 2 LVDS/CMOS output bit 0 (LSB) |
| Контакт 44 | D1_2 — Channel 2 output bit 1 |
| Контакт 45 | D2_2 — Channel 2 output bit 2 |
| Контакт 46 | D3_2 — Channel 2 output bit 3 |
| Контакт 47 | D4_2 — Channel 2 output bit 4 |
| Контакт 48 | D5_2 — Channel 2 output bit 5 |
| Контакт 49 | D6_2 — Channel 2 output bit 6 |
| Контакт 50 | D7_2 — Channel 2 output bit 7 |
| Контакт 51 | D8_2 — Channel 2 output bit 8 |
| Контакт 52 | D9_2 — Channel 2 output bit 9 |
| Контакт 53 | D10_2 — Channel 2 output bit 10 |
| Контакт 54 | D11_2 — Channel 2 output bit 11 |
| Контакт 55 | D12_2 — Channel 2 output bit 12 |
| Контакт 56 | D13_2 — Channel 2 output bit 13 (MSB) |
| Контакт 57 | DCLK2 — Channel 2 DDR clock output |
| Контакт 58 | FR_N_2 — Channel 2 frame indicator (active low) |
| Контакт 59 | OGND — Output driver ground |
| Контакт 60 | OVDD — Output driver supply (1.8 V nominal) |
| Контакт 61 | MODE — Output mode select (CMOS/LVDS) |
| Контакт 62 | CS — Chip select / SPI enable |
| Контакт 63 | SDI — SPI serial data input |
| Контакт 64 | SCK — SPI serial clock |
| Контакт EP | EPAD — Exposed pad - must be soldered to ground plane for thermal dissipation |
Типичное применение
LTC2158CUP-14 подходит для 6 применениеs: Cellular Base-Station Receivers, Radar and Phased-Array Signal Processing, Test and Measurement Instrumentation, Communications Signal Analyzers, Medical Imaging Systems, Software Defined Radio (SDR).
Cellular Base-Station Receivers
The LTC2158CUP-14's dual simultaneous 310 Msps sampling and 1.25 GHz input bandwidth make it ideal for cellular base-station receiver digitizers. In a typical LTE or 5G NR base-station design, the antenna signal is downconverted to an IF, filtered, and then applied to the ADC's differential inputs. The 88 dB SFDR allows the receiver to detect small signals alongside large blockers, while the 14-bit resolution preserves EVM margins for high-order modulation. The two channels support diversity or multi-band capture from a single converter IC, simplifying PCB layout and reducing BOM cost compared with two single-channel ADCs.
Рекомендуется
Radar and Phased-Array Signal Processing
The LTC2158CUP-14 is well-suited to radar and phased-array receiver front ends where dual simultaneous sampling captures I/Q or two antenna channels on the same clock edge. The 68.8 dB SNR supports detection of small radar returns, and the 1.25 GHz input bandwidth allows direct IF sampling of L-band or S-band radar carriers. Each ADC channel drives an FPGA or ASIC for digital beamforming, with the LVDS output option minimizing digital switching noise. The 64-QFN exposed-pad construction ensures low thermal resistance for continuous full-rate operation in mission-critical systems.
Рекомендуется
Test and Measurement Instrumentation
In high-end oscilloscopes, spectrum analyzers, and arbitrary waveform digitizers, the LTC2158CUP-14's 14-bit resolution and 310 Msps rate deliver the dynamic range and bandwidth needed for accurate signal capture. The 88 dB SFDR keeps harmonic distortion well below the noise floor of typical measurements, and the 1.25 GHz input bandwidth extends usable frequency range into microwave IF regions. Dual channels allow two-probe simultaneous acquisition or trigger/auxiliary digitizing from a single chip. The exposed-pad QFN-64 package provides mechanical robustness and thermal headroom for continuous full-rate operation.
Рекомендуется
Communications Signal Analyzers
The LTC2158CUP-14 supports communications signal analyzers and vector signal analyzer front ends that must capture wide-bandwidth modulated signals with high fidelity. Its 14-bit resolution provides sufficient dynamic range for EVM measurements on 1024-QAM or higher-order constellations, while the 310 Msps rate allows analysis of 100 MHz+ instantaneous bandwidth carriers. The two channels can capture dual-polarized antenna signals or main/auxiliary receiver paths. Differential inputs and integrated common-mode bias simplify the interface to the preceding mixer/IF filter stage.
Рекомендуется
Medical Imaging Systems
Ultrasound and other medical imaging front ends benefit from the LTC2158CUP-14's dual simultaneous 310 Msps channels and 1.25 GHz input bandwidth. Beamformed ultrasound receivers need many coherent ADC channels; the LTC2158CUP-14 captures two channels per chip with tight channel-to-channel phase alignment derived from the shared clock edge. The 14-bit resolution supports the wide dynamic range required for both strong specular reflections and weak tissue echoes. Low-voltage 1.8 V supply operation simplifies integration into portable cart-based ultrasound systems.
Рекомендуется
Software Defined Radio (SDR)
Software-defined radio platforms benefit from the LTC2158CUP-14's wide 1.25 GHz analog input bandwidth, which allows direct sampling of HF, VHF, and lower-UHF signals without an explicit analog downconversion stage. Dual channels support full I/Q capture for quadrature demodulation in DSP, or two independent receiver slices for multi-band listening. The 14-bit resolution preserves dynamic range across both strong broadcast and weak amateur signals. CMOS or DDR LVDS digital outputs interface directly to FPGAs running GNU Radio or vendor DSP frameworks.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2158CUP-14 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2158IUP-14 | LTC2157CUP-14 | LTC2156IUP-14 | LTC2155CUP-12 |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same |
| Resolution | 14 bit | 14 bit | 14 bit | 14 bit | 12 bit |
| Sampling Rate | 310 Msps | 310 Msps | 250 Msps | 210 Msps | 250 Msps |
| Number of Channels | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous |
| Output Format | CMOS / DDR LVDS | CMOS / DDR LVDS | CMOS / DDR LVDS | CMOS / DDR LVDS | CMOS / DDR LVDS |
| RoHS Status | Compliant (PBF) | Compliant (PBF) | Compliant (PBF) | Compliant (PBF) | Compliant (PBF) |
Ключевые отличия
- Highest sample rate in 64-QFN dual-ADC family (против LTC2157CUP-14)
- Higher 1.25 GHz input bandwidth for IF sampling (против LTC2156IUP-14)
- 14-bit resolution vs 12-bit option (против LTC2155CUP-12)
- Dual simultaneous sampling on a single chip (против LTC2151CUJ-14 (single-channel 40-QFN))
Заметки по проектированию
Each AVDD and OVDD pin must be decoupled individually with a 0.1 uF ceramic capacitor placed within 5 mm of the pin and a 10 uF bulk capacitor placed nearby. Use a low-noise LDO such as the LT3042 or LT1764 upstream of the 1.8 V analog rail to minimize supply-induced jitter. Avoid sharing the ADC analog supply return path with digital logic return currents; use a star-ground topology at the exposed pad.
The exposed pad (EPAD) must be soldered to a continuous ground plane with multiple thermal vias for heat extraction. Route the differential clock (CLK+/CLK-) and analog inputs (AIN1+, AIN1-, AIN2+, AIN2-) as 100 ohm differential striplines with length matching better than 1 mm. Keep digital LVDS output traces short and routed over a continuous ground reference to control common-mode noise.
Source the ADC sampling clock from a low-jitter clock generator such as the AD9516-0 or HMC7044 with RMS jitter below 200 fs to preserve SNR at the full 310 Msps rate. Avoid using FPGA PLLs for the ADC clock because their jitter is typically too high. For LVDS output mode, terminate the differential pairs with 100 ohm near the receiver FPGA inputs to minimize reflections.
Do not omit the reference decoupling caps on REFT and REFB - this directly degrades SFDR. Ensure the input common-mode voltage (VCM) pins are bypassed with 0.1 uF caps; floating these pins causes linearity errors. The SENSE pin must be tied to AGND for internal reference mode or to AVDD for external reference mode per datasheet. Failure to set SENSE correctly will result in incorrect full-scale range.
Информация о соответствии
#PBF suffix indicates lead-free RoHS-compliant finish per Analog Devices ordering information. Industrial temperature grade variant (LTC2158IUP-14) is also available. AEC-Q100 not applicable - this is a commercial/industrial grade high-speed ADC.
