MAX232ECDW - 250kbps RS-232 Transceiver | Texas Instruments
Артикул: MAX232ECDW ✓ АктивенMAX232ECDW Обзор
A MAX232 device is a bipolar RS-232 interface transceiver that converts logic-level signals between TTL/CMOS equipment and the positive and negative voltage levels used by RS-232 links. Within the interface IC hierarchy, the MAX232 belongs to the line-driver and line-receiver family, bridging a digital controller or computer port and a physical serial communication cable.
The MAX232ECDW integrates two transmit channels and two receive channels, allowing two bidirectional RS-232 ports or one port plus additional point-to-point links to be supported by one device. Its specified operating supply range is 4.5V to 5.5V, and its maximum signaling rate is 250 kbps. IEC 61000-4-2 protection adds electrostatic-discharge resilience to a frequently touched external interface.
Internally, the device uses a charge-pump voltage generator to produce the bipolar RS-232 voltage levels required by the drivers while operating from a single low-voltage supply. The receivers convert bipolar RS-232 inputs to TTL and CMOS logic levels, with a typical receiver threshold of 1.3V according to the manufacturer datasheet. Together, the dual-channel arrangement and 250 kbps capability suit control, instrumentation, industrial communication, and legacy computer interfaces.
Typical uses include service-console connections, factory equipment interfaces, laboratory instruments, embedded serial bridges, and industrial controllers that retain an RS-232 port. The device is appropriate when a system requires full RS-232 rather than TTL logic levels, particularly for cable connections where voltage polarity, ground reference, and ESD exposure must be considered.
A robust layout should place the charge-pump capacitors and supply-decoupling capacitors close to their associated pins, while keeping protected connector-side traces away from sensitive logic. External protection and signal-conditioning components may still be needed when the connected cable is long or the port is exposed to severe industrial transients.
This page consolidates the principal electrical characteristics, package details, drop-in replacement candidates, application guidance, and design cautions engineers need when evaluating the MAX232ECDW for an RS-232 interface.
Аналоги без доработки для MAX232ECDW — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX232ECDW (тот же форм-фактор и посадочное место) — отличается по Maximum Data Rate, Product Type, Interface Standard, Number of Drivers, Number of Receivers.
MAX232CWE+T
✅ Прямая заменаУточнить цену
Открыть даташит →MAX232IDWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX202CDWR
✅ Прямая заменаУточнить цену
Открыть даташит →MAX232EIDR
✅ Прямая заменаУточнить цену
Открыть даташит →MAX232ECDW Характеристики
| Product Type | Dual RS-232 driver/receiver transceiver |
| Number of Drivers | 2 drivers |
| Number of Receivers | 2 receivers |
| Interface Standard | RS-232 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Receiver Threshold | 1.3 V typical |
| ESD Protection Standard | IEC 61000-4-2 |
| Package Type | 16-pin SOIC |
| Package Pin Count | 16 pins |
| Тип монтажа | Surface mount |
| Packaging Type | Tube |
| Transmitter Output Type | RS-232 bipolar line driver |
| Receiver Output Type | TTL/CMOS logic-level receiver |
| Operating Voltage | 4.5 V to 5.5 V |
Руководство по цоколевке MAX232ECDW в корпусе 16 pins
Цоколевка для MAX232ECDW (корпус 16 pins). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX232ECDW.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX232ECDW подходит для 6 применениеs: Industrial Controller Serial Port, Laboratory Instrument Interface, Service and Diagnostics Port, Factory Equipment Communication, Embedded Serial Port Bridge, Legacy Computer Peripherals.
Industrial Controller Serial Port
The MAX232ECDW fits industrial controllers that retain an RS-232 port for programming, configuration, or service communications. Its two drivers and two receivers support two channel directions while operating from a conventional 4.5V to 5.5V rail, and the 250 kbps maximum rate covers many legacy equipment protocols. The 16-pin SOIC package simplifies integration with an existing controller board. IEC 61000-4-2 protection is valuable when the connector is accessible to operators, although the connector shield, cable grounding, and any required transient protection must still be engineered for the installation.
Рекомендуется
Laboratory Instrument Interface
The MAX232ECDW is suitable for laboratory instruments that communicate with a host computer through an RS-232 connection. At rates up to 250 kbps, it can support older instrument-control protocols that do not require a modern high-speed serial interface. Its receivers translate the bipolar RS-232 levels into TTL/CMOS logic, while the drivers provide the required RS-232 output levels from a single 5V-class supply. The documented 1.3V typical receiver threshold helps define the input transition region, and ESD protection reduces vulnerability at a connector exposed to operator contact.
Рекомендуется
Service and Diagnostics Port
The MAX232ECDW can provide a service-console interface for embedded equipment that needs a simple point-to-point RS-232 link. Two transmitters and two receivers allow the design to implement a bidirectional service channel or a second diagnostic channel without using separate single-channel interface packages. Operation from 4.5V to 5.5V fits conventional embedded logic supplies, and the 250 kbps capability accommodates common legacy diagnostic baud rates. Its IEC 61000-4-2 protection is particularly relevant when technicians connect a cable directly to the product during installation or maintenance.
Рекомендуется
Factory Equipment Communication
The MAX232ECDW is appropriate for factory equipment that communicates over an established RS-232 link to a controller or data-acquisition system. The 250 kbps rate supports typical industrial serial links, while two drivers and two receivers provide flexibility for bidirectional command and telemetry paths. Its 4.5V to 5.5V operating range permits use with a regulated 5V rail in control electronics. IEC 61000-4-2 protection adds a useful layer at an accessible port, but long cable runs may require additional surge protection, filtering, and careful common-ground treatment to avoid communication errors.
Рекомендуется
Embedded Serial Port Bridge
The MAX232ECDW can serve as the physical RS-232 layer in an embedded bridge or controller that converts a low-voltage UART into a cable-compatible RS-232 signal. The internal charge-pump function produces the bipolar driver voltage from one 4.5V to 5.5V supply, avoiding a separate negative rail. Data rates up to 250 kbps cover conventional UART-based management protocols. The 16-pin SOIC package supports compact controller layouts, while ESD protection helps manage static discharge at an external connector. Firmware should use the device’s receiver threshold and system ground arrangement as part of its communication-error budget.
Рекомендуется
Legacy Computer Peripherals
The MAX232ECDW supports legacy computer peripherals and service equipment that use an RS-232 port rather than USB or a modern differential interface. A single device provides two driver outputs and two receiver inputs, allowing a controller to retain more than one legacy serial connection. The 250 kbps maximum data rate covers many established COM-port applications, and the 4.5V to 5.5V supply range works with conventional 5V systems. When adding the IC to a modern design, verify that the host UART logic levels, connector gender, cable pinout, and software protocol remain compatible with the legacy peripheral.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX232ECDW — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX232CWE+T | MAX232IDWR | MAX202CDWR | MAX232EIDR |
|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Interface Type | Full RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
Ключевые отличия
- Documented protection for externally accessible RS-232 ports (против MAX232CWE+T)
- Matches the core operating requirements of a direct replacement candidate (против MAX232CWE+T)
- Combines two full RS-232 channels in a 16-pin package (против MAX202CDWR)
Заметки по проектированию
Place all charge-pump capacitors and supply bypass components directly beside their associated MAX232ECDW pins, with short and low-loop-area connections. Keep the connector-side driver and receiver traces away from sensitive logic and clocks wherever possible. The exposed connector region should also be arranged to limit electrostatic discharge from entering the logic side of the board.
Do not treat the RS-232 ground as an optional signal wire. Maintain a common reference between the transceiver board and the connected equipment, especially across long or industrial cables. Also verify connector pin assignments and signal polarity before assembly because an incorrect RS-232 cable connection can defeat otherwise correct logic design.
The MAX232ECDW’s charge-pump circuitry can produce harmonics on the 5V supply. Use the manufacturer-specified local bypass capacitance and keep the charge-pump loop compact to limit coupling into adjacent analog or digital circuits. If the RS-232 port shares a board with sensitive measurement circuitry, monitor supply ripple and place the transceiver near the connector to shorten external routes.
Информация о соответствии
IEC 61000-4-2 ESD protection is documented for the MAX232ECDW. Separate material-compliance declarations were not established from the referenced manufacturer or distributor information.