MAX3243EIPWE4 - 3/5 RS-232 Transceiver | Texas Instruments
Артикул: MAX3243EIPWE4 ✓ АктивенMAX3243EIPWE4 Обзор
An RS-232 transceiver is an interface IC that converts between single-ended, bipolar RS-232 voltage levels and the lower-voltage logic levels used by digital circuits. The MAX3243 belongs to the broader line-driver and receiver hierarchy, combining three transmit channels with five receive channels in one device. Its multichannel arrangement allows one package to support several serial ports or a mixture of host and peripheral connections while reducing the number of interface components on the PCB.
The MAX3243EIPWE4 operates from a 3 V to 5.5 V supply, making it suitable for systems using either 3.3 V or 5 V logic. Its stated maximum data rate of 250 kbps addresses conventional RS-232 links used by embedded controllers, test equipment, industrial controls, and point-of-sale systems. ±15 kV electrostatic-discharge protection helps improve robustness on connector-adjacent circuits where cables can expose equipment to electrostatic discharge.
The industrial temperature grade, rectangular gull-wing TSSOP-28 package, and 28 terminals make the device appropriate for leaded-surface-mount industrial assemblies. Operating from a 3 V to 5.5 V supply also allows logic-level sharing with modern microcontrollers and programmable controllers. The three-driver and five-receiver arrangement can conserve board area compared with separate one-channel line-driver and receiver packages when several RS-232 signals must be handled.
When designing the interface, connect each driver to the appropriate RS-232 TX and receiver to the RS-232 RX lines, then keep logic-side signals within the supply voltage. Place the required charge-pump capacitors and interface-network components according to the manufacturer datasheet. Route the exposed connector and cable paths away from sensitive logic, and provide the specified ESD-protection network where the transceiver is not adjacent to the connector.
For reliable operation, verify that the selected UART supports the required 250 kbps line rate and that the cable length and baud rate satisfy RS-232 practice. Ensure power sequencing does not enable the interface before its logic supply is stable. This page compares the MAX3243EIPWE4 with documented alternatives and summarizes package, channel-count, speed, protection, and supply considerations for faster engineering selection.
Аналоги без доработки для MAX3243EIPWE4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
SP3243EBCY-L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3243EIPWE4 Характеристики
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV |
| Number of Drivers | 3 |
| Number of Receivers | 5 |
| Duplex Operation | Full duplex |
| Logic Compatibility | TTL/CMOS |
| Package Type | TSSOP-28 |
| Terminal Count | 28 |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Тип монтажа | Surface mount |
| Temperature Grade | Industrial |
Руководство по цоколевке MAX3243EIPWE4 в корпусе rectangular
Цоколевка для MAX3243EIPWE4 (корпус rectangular). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3243EIPWE4.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3243EIPWE4 подходит для 6 применениеs: Industrial Controller Serial Interfaces, Embedded Equipment Communication, Test and Measurement Equipment, Point-of-Sale and Retail Systems, Data Acquisition and Control Panels, Security and Access-Control Equipment.
Industrial Controller Serial Interfaces
The MAX3243EIPWE4 suits industrial controllers that need several RS-232 ports for sensors, programmers, meters, or service equipment. Its three drivers and five receivers provide more channel density than separate single-channel transceivers, while the 3 V to 5.5 V supply range accommodates common industrial logic levels. The 250 kbps maximum rate supports conventional serial control protocols. Designers should place the manufacturer-specified charge-pump capacitors close to the device and use ESD-protection components when the connector is remote from the transceiver.
Рекомендуется
Embedded Equipment Communication
The MAX3243EIPWE4 can bridge a microcontroller UART and RS-232 equipment used for configuration, logging, or service diagnostics. Three transmit channels support commands and status signals, while five receive channels can accept acknowledgments, measurements, or responses from multiple devices. Operation from 3 V to 5.5 V permits use with both 3.3 V and 5 V controllers. Keep the logic-side traces short, confirm UART baud-rate capability, and validate the external capacitor and protection network in the final enclosure.
Рекомендуется
Test and Measurement Equipment
The MAX3243EIPWE4 is appropriate for test instruments and laboratory interfaces that exchange commands and results over RS-232. The 250 kbps rate is appropriate for many low- and medium-speed measurement protocols, and the five receiver channels can monitor several status or acknowledgment inputs. The industrial temperature grade supports equipment operated across demanding ambient conditions. Use short, properly terminated logic traces, preserve the recommended charge-pump layout, and keep unprotected cable conductors away from sensitive analog circuitry.
Рекомендуется
Point-of-Sale and Retail Systems
Point-of-sale terminals, scanners, and peripherals can use the MAX3243EIPWE4 for multiple RS-232 connections to displays, scales, scanners, or service equipment. Three driver channels cover outbound commands and data, while five receiver channels support inbound responses and status lines. Its 3 V to 5.5 V operating range integrates with mixed logic systems, and ±15 kV ESD protection adds useful robustness at connector-facing locations. Verify cable length against the intended baud rate and place protection components at the connector entry.
Рекомендуется
Data Acquisition and Control Panels
The MAX3243EIPWE4 fits acquisition panels that receive commands from a host and return data from multiple instruments or control modules. Five receiver inputs reduce the number of packages required when several devices report status, while three outputs can provide control or query signals. The 250 kbps maximum rate accommodates many legacy instrumentation protocols. Confirm ground-referenced logic compatibility, use the manufacturer-recommended charge-pump capacitor arrangement, and provide local ESD protection where long external cables enter the enclosure.
Рекомендуется
Security and Access-Control Equipment
Access-control panels and security peripherals can use the MAX3243EIPWE4 to connect a controller to readers, alarm modules, or configuration tools through RS-232. The device combines three transmit and five receive channels in one 28-pin TSSOP, reducing board-space requirements in compact equipment. Its 3 V to 5.5 V range supports common embedded logic families, and the stated ±15 kV ESD protection supports protection planning for connector-accessible circuitry. Add surge and ESD networks appropriate to the installation environment and maintain proper chassis grounding.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3243EIPWE4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SP3243EBCY-L |
|---|---|---|
| Brand | Texas Instruments | MaxLinear |
| Package | TSSOP-28 | TSSOP-28 |
| Product Type | Multichannel RS-232 line driver/receiver | Multichannel RS-232 transceiver |
| Maximum Data Rate | 250 kbps | 500 kbps |
| Drivers | 3 | 3 |
| Receivers | 5 | 5 |
| Mounting Type | Surface mount | Surface mount |
Ключевые отличия
- Five receive channels provide more receive density than the three available transmit channels (против SP3243EBCY-L)
- Defined 250 kbps maximum data rate (против SP3243EBCY-L)
- Specified ±15 kV ESD protection (против SP3243EBCY-L)
Заметки по проектированию
Place the charge-pump capacitors and the transceiver input and output network close to their associated pins. Keep the high-voltage RS-232 driver traces away from UART logic, clocks, analog inputs, and sensitive return paths. Use the manufacturer’s application circuit as the layout baseline, minimize loop area, and connect the device ground directly to a quiet ground plane rather than routing it through switching-current paths.
Treat the RS-232 connector as an electrostatic-discharge entry point. Position the specified protection network at the connector, use the shortest practical connection to the driver and receiver pins, and maintain the recommended series resistance. Confirm that the cable, baud rate, and grounding arrangement are appropriate for the installation because ESD protection does not replace correct RS-232 signal integrity practices.
Do not substitute a reduced-channel device without rewriting the PCB, and do not treat a shared TSSOP-28 outline as proof of compatibility. Verify every pin, the charge-pump capacitor values, shutdown behavior, and the driver and receiver logic states against both datasheets. The SP3243EBCY-L is reported as a complete 28-pin replacement, while the MAX3243EIPWR is a reel-ordering form of the same device and should not be counted as a distinct functional alternative.
Информация о соответствии
The manufacturer product page identifies the MAX3243 as an industrial-temperature RS-232 interface with ±15 kV ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.