MC14024BF - 7-Bit CMOS Ripple Counter IC | onsemi
Артикул: MC14024BF ✓ АктивенMC14024BF Обзор
A binary ripple counter is a logic IC that advances through a sequence of binary values when an external clock edge is applied. The MC14024BF belongs to the CMOS counter and divider category within the broader hierarchy of digital logic, logic ICs, and integrated circuits. Its seven stages can be used independently as modulo counters, frequency division stages, state-counting elements, or a complete seven-bit counter when the output stages are chained internally.
The key operating features include seven counter stages, buffered outputs, negative-edge triggering, asynchronous counting, and hysteresis on the clock input for improved noise immunity. The reset input uses standard noise immunity. These characteristics make the device useful when a design requires a simple counter without a dedicated microprocessor or programmable logic. The 3 V to 18 V supply range permits operation across common low-voltage and conventional CMOS supply systems.
The ripple architecture advances one stage per clock event, with propagation delay accumulating through the cascaded stages. Each output is buffered, allowing individual stage outputs to be observed or used in external logic. Because the maximum operating frequency and timing limits depend on operating voltage and temperature, the onsemi MC14024B datasheet should be consulted for the applicable values before relying on the counter at a system clock edge that approaches the device limit.
Typical applications include digital event counting, pulse accumulation, seven-segment sequencing control, industrial timing, frequency division, laboratory instrumentation, and embedded control logic. The MC14024BF can count external events when the input signal remains within the electrical limits of its clock input. Its buffered outputs are particularly useful when one or more counter states must drive gates, indicators, or control signals independently.
For reliable implementation, connect the reset to a defined inactive state, maintain clean clock edges, and observe the supply-voltage and temperature limits of 3 V to 18 V and -55°C to 125°C. Because ripple-counter outputs can change successively after a clock edge, downstream circuitry should not treat the seven outputs as a simultaneous encoded bus unless the timing requirements are specifically analyzed.
This page combines the onsemi counter architecture with application guidance, verified parameter availability, comparison fields, and practical implementation notes. It helps engineers distinguish the MC14024BF from other counter functions and identify what must be checked in the manufacturer datasheet before releasing a PCB or production design.
Аналоги без доработки для MC14024BF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиMC14024BF Максимальные параметры и электрические характеристики
| Counter Type | 7-bit asynchronous binary ripple counter |
| Number of Counter Stages | 7 stages |
| Output Count | 7 outputs |
| Supply Voltage Range | 3 V to 18 V |
| Диапазон рабочих температур | -55°C to +125°C |
| Clock Edge Sensitivity | Negative edge |
| Counting Direction | Up |
| Logic Family | CMOS |
| Output Buffering | Each counter stage is buffered |
| Clock Input Noise Immunity | Enhanced by hysteresis |
| Reset Input Noise Immunity | Standard |
| Package Type | PDSO14, 14 terminals |
| Terminal Count | 14 terminals |
| Тип монтажа | Surface mount |
Руководство по цоколевке MC14024BF в корпусе pdso14, 14 terminals
Цоколевка для MC14024BF (корпус pdso14, 14 terminals). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MC14024BF.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MC14024BF подходит для 6 применениеs: Digital Event and Pulse Counting, Frequency Division and Clock Scaling, Industrial Timing and Sequence Control, Seven-Segment Display Sequencing, Test and Measurement Instrumentation, Embedded Control Logic.
Digital Event and Pulse Counting
The MC14024BF fits digital event-counting systems that need a fixed seven-bit tally. Its negative-edge clock input counts one event for each valid falling edge, while the seven buffered outputs expose successive binary states for decoding or control. The onsemi MC14024B datasheet identifies clock hysteresis, which helps reject modest input noise. Design the input driver so the event signal crosses the switching threshold cleanly and does not exceed the specified electrical limits. Because this is a ripple counter, the seven output bits change successively rather than simultaneously, so downstream logic should not sample them as a synchronous binary bus without a timing review.
Frequency Division and Clock Scaling
The MC14024BF can divide an incoming clock through its seven cascaded stages, with each buffered stage providing a divide-by-two output. This is useful when a fixed frequency relationship is needed for slower timers, control clocks, or periodic sampling without a programmable timing device. The onsemi MC14024B datasheet confirms that every counter stage is buffered, allowing an individual stage to drive external logic. Select the stage that produces the required frequency, then verify its transition timing at the actual 3 V to 18 V supply and worst-case temperature. Ensure downstream logic does not require all counter outputs to change on the same edge.
Industrial Timing and Sequence Control
The MC14024BF supports fixed-duration timing, event sequencing, and repetitive machine-control functions where seven cascaded states are sufficient. Each output can trigger a gate, indicator, or state-dependent control function, while the clock input establishes the system cadence. The onsemi MC14024B datasheet describes standard reset noise immunity and enhanced clock-input noise immunity, supporting practical use in digital control equipment. Keep the reset path short and free of switching-node coupling, and validate the maximum clock rate under voltage and temperature conditions. The fixed seven-bit ripple topology is especially suitable when reprogrammability and parallel loading are not required.
Seven-Segment Display Sequencing
The MC14024BF can generate repetitive step sequences for a seven-segment display or similar multiplexed indicator when the counter outputs drive decoding logic. Its seven buffered stages provide a compact binary sequence without requiring a microcontroller, and the upward count supports cyclic scan-state advancement. The onsemi MC14024B datasheet confirms the seven-stage, buffered-output architecture and negative-edge counting behavior. Choose display drive components and interface levels that are compatible with the counter outputs, and account for ripple propagation delay when switching active elements. The counter is best suited to fixed repetitive patterns rather than arbitrary alphanumeric sequences requiring programmable storage.
Test and Measurement Instrumentation
The MC14024BF is appropriate for laboratory and test-equipment logic that counts test events, divides an instrument clock, or develops repeatable control steps. The buffered stage outputs can drive threshold indicators, range logic, or trigger sequencing without overloading the internal counter nodes. The onsemi MC14024B datasheet specifies operation over -55°C to +125°C, allowing use across wide environmental test profiles. For laboratory timing accuracy, evaluate clock-edge quality, propagation delay, and supply tolerance over the required frequency range. A microcontroller-based counter is preferable when measurements must be configured dynamically or results must be captured computationally.
Embedded Control Logic
The MC14024BF can provide a small autonomous counter beside a microcontroller in appliance controls, panel interfaces, or embedded automation. It continues a simple tally when external logic needs asynchronous events counted without occupying processor pins or interrupt capacity. The onsemi MC14024B datasheet confirms upward counting, negative-edge clock triggering, and buffered outputs. Connect the counter clock to a conditioned version of the event source, and use a reset generated by the surrounding control logic when a deterministic starting state is required. Avoid treating the ripple outputs as a coherent bus when the controller can sample during the transition interval.
Справочные инженерные данные для MC14024BF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Counter Function | 7-stage asynchronous binary ripple counter |
| Counter Width | 7 bits |
| Supply Voltage Range | 3 V to 18 V |
| Operating Temperature | -55°C to +125°C |
| Clock Edge | Negative edge |
| Counting Direction | Up |
| Output Type | Seven buffered counter outputs |
| Package | PDSO14, 14 terminals |
| Brand | onsemi |
Ключевые отличия
- Seven cascaded stages with buffered outputs (против MC14024BFELG)
- Negative-edge counting with clock hysteresis (против MC14024BFELG)
- Wide specified operating-temperature range (против MC14024BFELG)
Заметки по проектированию
Treat the clock as a single net and drive it from clean logic rather than from a long cable or noisy mechanical switch. The onsemi MC14024B datasheet identifies hysteresis as the reason for increased clock-input noise immunity, but hysteresis does not permit arbitrary bounce or slow transitions. For switch inputs, add conditioning and a Schmitt-trigger stage if the source can ring or cross the input threshold repeatedly. Route the clock away from switching nodes and keep the reset path short.
Do not interpret the seven ripple-counter outputs as a simultaneously updated binary bus. A clock edge initiates a sequence of stage transitions, so a receiver can observe intermediate count values during propagation. Use individual outputs for independent state indications, or add a latch and sampling strategy when a coherent encoded value is required. Also define the reset level during power-up so the counter begins from a known state rather than an uncontrolled sequence.
Follow the onsemi MC14024B datasheet and PDSO14 land-pattern drawing when assigning and routing the 14-terminal footprint. Provide a low-impedance supply and ground connection, place decoupling capacitance close to the supply terminals, and keep the clock trace short. Avoid routing the clock between noisy power-stage nodes. Confirm lead pitch, body dimensions, and solder-reflow classification before releasing the PCB because package family labels alone do not define a land pattern.
Информация о соответствии
The onsemi MC14024B datasheet is the controlling technical document, but no explicit compliance declarations for the exact MC14024BF ordering code are stated in the cited pages.