MC74F169M - 4-Stage Synchronous Counter | onsemi
Артикул: MC74F169M ✗ Снят с производстваMC74F169M Обзор
A synchronous counter is a digital logic device whose internal flip-flops change state on the same active clock edge. Unlike an asynchronous ripple counter, a synchronous counter updates all counting stages together, reducing propagation-delay variation between output bits. The MC74F169M also supports synchronous loading and counting in either direction, providing flexible control for repeatable state transitions.
The principal functional characteristics include four counting stages, a 4-bit counter architecture, positive-edge counting, bidirectional operation, and a modulo-16 count sequence. These characteristics allow the output word to advance from 0 through 15 in the selected direction. The device is suitable for digital frequency division, event counting, programmable sequencing, industrial timing, and control-logic applications where a compact counter is preferable to a programmable logic implementation.
The synchronous architecture keeps the counter stages aligned during each count transition, which helps maintain predictable outputs in multi-bit buses. The MC74F169M can therefore be used as a compact state counter, a modulo-16 sequencing element, or a building block for larger counters when additional cascaded stages are required. Cascading requires attention to count enable, carry, reset, and clock-edge relationships so that the combined counter advances only when intended.
Typical implementations include industrial control and automation equipment, electronic timers, test and measurement systems, digital instrumentation, and general-purpose logic designs. In a timer, the counter can divide an input clock into a lower-frequency update rate. In a sequencing circuit, it can advance through up to 16 states. In an event-counting system, it can retain a modulo-16 tally while external logic handles overflow interpretation.
When laying out the design, use the manufacturer pin-description table for the exact MC74F169M package and verify the meanings of the parallel-load, count-enable, clear, clock, and output signals. Keep clock and control traces short, provide a low-impedance ground reference, and isolate sensitive analog circuitry from digital switching nodes. Because counter outputs change on clock edges, include adequate timing margin for downstream combinational logic and synchronize asynchronous control inputs when they originate outside the local clock domain.
This page organizes the MC74F169M function, package information, comparison dimensions, sourcing workflow, and engineering guidance into one practical reference. It also distinguishes confirmed product attributes from details that require review in the manufacturer datasheet, helping designers move from identification to schematic validation with fewer packaging or timing mistakes.
Аналоги без доработки для MC74F169M — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиMC74F169M Максимальные параметры и электрические характеристики
| Counter Type | 4-stage synchronous bidirectional counter |
| Counting Element | 1 element |
| Counter Width | 4 bit |
| Count Sequence | Modulo 16 |
| Counting Direction | Bidirectional, up or down |
| Clock Edge | Positive edge |
| Logic Family | MC74F169 |
| Manufacturer | onsemi |
| Package Pin Count | 16 pin |
| Тип монтажа | Surface mount |
| Статус RoHS | Compliant |
Руководство по цоколевке MC74F169M в корпусе 16 pin
Цоколевка для MC74F169M (корпус 16 pin). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MC74F169M.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MC74F169M подходит для 6 применениеs: Digital Timer and Frequency Divider, Industrial Sequence Controller, Event and Batch Counter, Test and Measurement Instrument, Programmable Control Front End, General-Purpose Digital Logic.
Digital Timer and Frequency Divider
The MC74F169M is suitable for dividing a periodic input clock into a lower-rate counting sequence because it provides four synchronous counting stages and positive-edge operation. With an appropriate terminal count and reset arrangement, the device can generate repeatable modulo-16 timing intervals for clocked digital circuits. The synchronous architecture updates all four outputs on the same active edge, which helps downstream circuitry interpret the count as one coherent binary word. The input clock must remain within the manufacturer timing limits for the selected supply voltage, and the final output should include suitable reset synchronization to establish a deterministic starting state.
Рекомендуется
Industrial Sequence Controller
The MC74F169M can act as a compact 16-state sequencing element in industrial automation and control systems. Its four-bit bidirectional counter advances through up to 16 states, allowing control outputs to be decoded into repeatable machine steps, timing phases, or operating modes. Synchronous stage updates help the decoded state change on a defined clock edge rather than through a ripple of unequal propagation delays. Designers should decode only the required state outputs, keep combinational logic timing within budget, and use the manufacturer-defined clear and load controls to return the sequence safely to its initial condition.
Рекомендуется
Event and Batch Counter
The MC74F169M fits event-counting and batch-control designs that need to retain a four-bit modulo-16 tally. Each qualified clock event advances the count, while the application logic interprets the terminal state as a completed batch and resets or reloads the counter. Positive-edge operation makes the sampling point explicit and supports deterministic association between the event and the updated count. In noisy industrial environments, qualify the event source, protect unused inputs, and ensure that reset and load signals meet the timing requirements stated in the manufacturer datasheet.
Рекомендуется
Test and Measurement Instrument
The MC74F169M can organize repetitive measurement or stimulus steps in test and measurement equipment by cycling through a defined sequence of up to 16 states. The counter outputs can feed address or control decoding, while the external clock determines how quickly the instrument advances. Its synchronous operation produces a more coherent state transition than a ripple counter and supports repeatable multi-step procedures. The implementation should use a stable timebase, register any asynchronous commands before the counter clock edge, and protect the output bus from loading that could disturb timing or logic levels.
Рекомендуется
Programmable Control Front End
The MC74F169M is useful as a small front-end counter for programmable controllers that need event accumulation, phase counting, or modulo-based command pacing. It allows a controller to determine when a programmed number of steps or pulses has occurred while keeping the primary state machine compact. Because the device offers bidirectional counting, the same hardware can support progress counting, retrigger behavior, and reverse-index sequences. Firmware should use edge-defined events, include a timeout for missed or extra clocks, and read the counter only when the design guarantees a stable sampling instant.
Рекомендуется
General-Purpose Digital Logic
The MC74F169M provides a compact hardware solution for general-purpose digital logic requiring a repeatable 16-state counter without a programmable logic device. It can serve as a programmable divider, phase generator, state register, or building block in a larger counting system. The four-stage synchronous design supports predictable word updates, while the parallel control functions broaden its usefulness in legacy logic designs. Confirm the exact pin function and electrical behavior in the onsemi datasheet before final schematic capture, especially when unused inputs must be tied to defined logic levels.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC74F169M — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Brand | onsemi |
| Package | 16-pin surface-mount package indicated by the M suffix |
| Counter Type | 4-stage synchronous bidirectional counter |
| Counter Width | 4 bit |
| Count Sequence | Modulo 16 |
| Counting Direction | Up or down |
| Clock Edge | Positive edge |
| Counting Element | 1 element |
| RoHS Status | Compliant |
Ключевые отличия
- Compact bidirectional counting in one logic package (против 74F169)
- Surface-mount ordering option (против MC74F169N)
- Synchronous four-stage architecture (против MC74F169N)
Заметки по проектированию
Do not treat the MC74F169M and MC74F169N as interchangeable footprints. The N suffix identifies a 16-pin through-hole package, while the M suffix identifies the surface-mount ordering option. A schematic-level equivalence does not permit direct PCB substitution. Confirm the package drawing, lead pitch, row arrangement, and pin numbering against the onsemi datasheet before approving a replacement or releasing artwork.
Route the clock and clear signals as short, direct PCB traces, and keep the counter return path close to the device ground connection. Outputs that fan out to decoders or control logic should be routed away from sensitive analog nodes. When switching between count, load, and clear modes, verify that the transition timing satisfies the manufacturer setup and hold requirements so the counter always enters a defined state.
Treat every active count edge as a coordinated output transition because all four synchronous stages can update together. Check downstream decoder and bus timing at the maximum intended clock rate, and avoid adding long unprotected traces between counter outputs and high-fanout loads. If control signals originate in another clock domain, synchronize them before driving load, clear, or count-enable inputs to prevent metastability and unintended intermediate states.
Информация о соответствии
The MC74F169M product listing identifies the part as RoHS compliant. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is established by the cited sources.