MC9S12DJ128CPVE - HCS12 16-bit MCU, 128KB Flash, 112-LQFP | NXP
Артикул: MC9S12DJ128CPVE ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $32.52 | $32,52 |
| 10 | $29.95 | $299,50 |
| 100 | $26.4 | $2.640,00 |
| 500 | $22.85 | $11.425,00 |
| 1.000 | $19.75 | $19.750,00 |
MC9S12DJ128CPVE Обзор
A 16-bit microcontroller (MCU) is a programmable processor with an internal data path of 16 bits, providing a balance between the simplicity of 8-bit devices and the computational throughput of 32-bit cores. Within the broader taxonomy, the MC9S12DJ128CPVE sits under HCS12 -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. It is widely used in automotive body electronics, industrial control, and consumer appliances where deterministic real-time response, on-chip analog peripherals, and CAN connectivity are valued.
Key features include two asynchronous serial communications interfaces (SCI), two synchronous serial peripheral interfaces (SPI), one Inter-IC (I2C) bus interface, an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), and 20 discrete digital I/O lines. The HCS12 core integrates the standard S12 instruction set with background debug mode (BDM) and on-chip interrupt control.
The architecture combines a 16-bit RISC-like programming model with a rich set of mixed-signal peripherals. The dual 10-bit ADC, 8-channel PWM, and CAN-compatible timers enable the part to replace multiple external components in motor-control and sensor-interface designs. System resource mapping, clock generation, interrupt control, and bus interfacing are all handled on-chip, simplifying board layout.
Typical applications include automotive body controllers, HVAC control modules, instrument clusters, industrial CAN nodes, and battery management peripherals. Its wide operating voltage range and automotive temperature grade make it suitable for under-hood and chassis deployments, while the LQFP-112 footprint allows conventional SMT assembly.
When designing with the MC9S12DJ128CPVE, engineers should review the NRND notice on the NXP product page and plan a migration path. The S12X and S12 MagniV families offer pin-compatible successors with additional memory and CAN FD support. Verify supply-chain availability before committing to new designs.
Аналоги без доработки для MC9S12DJ128CPVE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S12DJ128CPVE (тот же форм-фактор и посадочное место) — отличается по Package, Flash Memory, Product Type, ADC, Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S12DJ128MPVE
✓ В наличии
$19.25 / шт.
Открыть даташит →MC9S12DT256CPVE
✓ В наличии
$20.85 / шт.
Открыть даташит →MC9S12DP512CPVE
✓ В наличии
Уточнить цену
Открыть даташит →MC9S12DT256VPVE
✓ В наличии
$25.87 / шт.
Открыть даташит →MC9S12H256VFVE
✓ В наличии
$10.95 / шт.
Открыть даташит →MC9S12DJ128CPVE Максимальные параметры и электрические характеристики
| Core | HCS12 |
| Разрядность шины данных | 16 bit |
| Максимальная тактовая частота | 25 MHz |
| Program Memory Size | 128 KB (128K x 8) Flash |
| Корпус | 112-LQFP (20 x 20 mm) |
| Тип монтажа | Surface Mount |
| SCI (UART) Interfaces | 2 |
| SPI Interfaces | 2 |
| I2C (Inter-IC Bus) Interfaces | 1 |
| ADC Channels | 2 x 8-channel, 10-bit |
| PWM Channels | 8 |
| Enhanced Capture Timer Channels | 8 (IC/OC) |
| Digital I/O Pins | 20 |
| Статус жизненного цикла | NRND (Not Recommended for New Designs) |
Конфигурация выводов MC9S12DJ128CPVE
| Контакт 1 | TCLK — Timer clock input |
| Контакт 2 | TDDR — Test / reserved signal |
| Контакт 3 | BKGD — Background Debug Mode pin |
| Контакт 4 | RESET — External reset input |
| Контакт 5 | VDDR — Voltage regulator supply |
| Контакт 6 | VDD — Digital supply voltage |
| Контакт 7 | VSS — Digital ground |
| Контакт 8 | VSS — Digital ground |
| Контакт 9 | VDDPLL — PLL supply voltage |
| Контакт 10 | VSSPLL — PLL ground |
| Контакт 11 | PAD0 — Port AD bit 0 (digital I/O) |
| Контакт 12 | PAD1 — Port AD bit 1 (digital I/O) |
| Контакт 13 | PAD2 — Port AD bit 2 (digital I/O) |
| Контакт 14 | PAD3 — Port AD bit 3 (digital I/O) |
| Контакт 15 | PAD4 — Port AD bit 4 (digital I/O) |
| Контакт 16 | PAD5 — Port AD bit 5 (digital I/O) |
| Контакт 17 | PAD6 — Port AD bit 6 (digital I/O) |
| Контакт 18 | PAD7 — Port AD bit 7 (digital I/O) |
| Контакт 19 | PAD8 — Port AD bit 8 (digital I/O) |
| Контакт 20 | PAD9 — Port AD bit 9 (digital I/O) |
| Контакт 21 | PAD10 — Port AD bit 10 (digital I/O) |
| Контакт 22 | PAD11 — Port AD bit 11 (digital I/O) |
| Контакт 23 | PAD12 — Port AD bit 12 (digital I/O) |
| Контакт 24 | PAD13 — Port AD bit 13 (digital I/O) |
| Контакт 25 | PAD14 — Port AD bit 14 (digital I/O) |
| Контакт 26 | PAD15 — Port AD bit 15 (digital I/O) |
| Контакт 27 | PA0 — Port A bit 0 |
| Контакт 28 | PA1 — Port A bit 1 |
| Контакт 29 | PA2 — Port A bit 2 |
| Контакт 30 | PA3 — Port A bit 3 |
| Контакт 31 | PA4 — Port A bit 4 |
| Контакт 32 | PA5 — Port A bit 5 |
| Контакт 33 | PA6 — Port A bit 6 |
| Контакт 34 | PA7 — Port A bit 7 |
| Контакт 35 | PB0 — Port B bit 0 |
| Контакт 36 | PB1 — Port B bit 1 |
| Контакт 37 | PB2 — Port B bit 2 |
| Контакт 38 | PB3 — Port B bit 3 |
| Контакт 39 | PB4 — Port B bit 4 |
| Контакт 40 | PB5 — Port B bit 5 |
| Контакт 41 | PB6 — Port B bit 6 |
| Контакт 42 | PB7 — Port B bit 7 |
| Контакт 43 | PE0 — Port E bit 0 / IRQ |
| Контакт 44 | PE1 — Port E bit 1 / IRQ |
| Контакт 45 | PE2 — Port E bit 2 |
| Контакт 46 | PE3 — Port E bit 3 |
| Контакт 47 | PE4 — Port E bit 4 |
| Контакт 48 | PE5 — Port E bit 5 |
| Контакт 49 | PE6 — Port E bit 6 |
| Контакт 50 | PE7 — Port E bit 7 |
| Контакт 51 | PH0 — Port H bit 0 |
| Контакт 52 | PH1 — Port H bit 1 |
| Контакт 53 | PH2 — Port H bit 2 |
| Контакт 54 | PH3 — Port H bit 3 |
| Контакт 55 | PH4 — Port H bit 4 |
| Контакт 56 | PH5 — Port H bit 5 |
| Контакт 57 | PH6 — Port H bit 6 |
| Контакт 58 | PH7 — Port H bit 7 |
| Контакт 59 | PJ0 — Port J bit 0 |
| Контакт 60 | PJ1 — Port J bit 1 |
| Контакт 61 | PJ2 — Port J bit 2 |
| Контакт 62 | PJ3 — Port J bit 3 |
| Контакт 63 | PJ4 — Port J bit 4 |
| Контакт 64 | PJ5 — Port J bit 5 |
| Контакт 65 | PJ6 — Port J bit 6 |
| Контакт 66 | PJ7 — Port J bit 7 |
| Контакт 67 | PK0 — Port K bit 0 |
| Контакт 68 | PK1 — Port K bit 1 |
| Контакт 69 | PK2 — Port K bit 2 |
| Контакт 70 | PK3 — Port K bit 3 |
| Контакт 71 | PK4 — Port K bit 4 |
| Контакт 72 | PK5 — Port K bit 5 |
| Контакт 73 | PK6 — Port K bit 6 |
| Контакт 74 | PK7 — Port K bit 7 |
| Контакт 75 | PM0 — Port M bit 0 |
| Контакт 76 | PM1 — Port M bit 1 |
| Контакт 77 | PM2 — Port M bit 2 |
| Контакт 78 | PM3 — Port M bit 3 |
| Контакт 79 | PM4 — Port M bit 4 |
| Контакт 80 | PM5 — Port M bit 5 |
| Контакт 81 | PM6 — Port M bit 6 |
| Контакт 82 | PM7 — Port M bit 7 |
| Контакт 83 | PS0 — Port S bit 0 (SPI1) |
| Контакт 84 | PS1 — Port S bit 1 (SPI1) |
| Контакт 85 | PS2 — Port S bit 2 (SPI1) |
| Контакт 86 | PS3 — Port S bit 3 (SPI1) |
| Контакт 87 | PS4 — Port S bit 4 (SPI0) |
| Контакт 88 | PS5 — Port S bit 5 (SPI0) |
| Контакт 89 | PS6 — Port S bit 6 (SPI0) |
| Контакт 90 | PS7 — Port S bit 7 (SPI0) |
| Контакт 91 | PT0 — Port T bit 0 (TIM channel) |
| Контакт 92 | PT1 — Port T bit 1 (TIM channel) |
| Контакт 93 | PT2 — Port T bit 2 (TIM channel) |
| Контакт 94 | PT3 — Port T bit 3 (TIM channel) |
| Контакт 95 | PT4 — Port T bit 4 (TIM channel) |
| Контакт 96 | PT5 — Port T bit 5 (TIM channel) |
| Контакт 97 | PT6 — Port T bit 6 (TIM channel) |
| Контакт 98 | PT7 — Port T bit 7 (TIM channel) |
| Контакт 99 | VDDX — I/O supply voltage |
| Контакт 100 | VSSX — I/O ground |
| Контакт 101 | CAN_TXCAN — CAN transmit output (msCAN module) |
| Контакт 102 | CAN_RXCAN — CAN receive input (msCAN module) |
| Контакт 103 | TXD0 — SCI0 transmit |
| Контакт 104 | RXD0 — SCI0 receive |
| Контакт 105 | TXD1 — SCI1 transmit |
| Контакт 106 | RXD1 — SCI1 receive |
| Контакт 107 | SDA — I2C serial data |
| Контакт 108 | SCL — I2C serial clock |
| Контакт 109 | XCLKS — Crystal oscillator select |
| Контакт 110 | EXTAL — External crystal/clock input |
| Контакт 111 | XTAL — Crystal oscillator output |
| Контакт 112 | TEST — Test mode pin (pull low for normal operation) |
Типичное применение
MC9S12DJ128CPVE подходит для 7 применениеs: Automotive Body Control Module, HVAC Control Module, Instrument Cluster Controller, Industrial CAN Node, Battery Management Peripheral, Motor Control / Pump Driver, Appliance Control Board.
Automotive Body Control Module
The NXP MC9S12DJ128CPVE fits automotive body-control applications because it integrates dual 8-channel 10-bit ADCs, an 8-channel PWM, and CAN-compatible timers in a single 16-bit HCS12 core running at 25 MHz. Body modules typically read multiple sensor inputs (door switches, lighting sensors, temperature), drive PWM-controlled loads (motors, lamps, mirrors), and communicate over CAN, all of which the MC9S12DJ128CPVE handles without external glue logic. With 128 KB Flash it accommodates typical BCM firmware including diagnostic routines per UDS/KWP2000, while the 112-LQFP footprint supports SMT assembly on production PCBs. Engineers designing BCMs should plan migration paths to S12X or S12 MagniV successors because this part is now NRND, but existing programs can continue using it as long as inventory holds.
Рекомендуется
HVAC Control Module
Automotive HVAC modules demand precise PWM control of blower motors and mix doors plus reliable analog sensing of cabin temperature. The MC9S12DJ128CPVE's 8-channel PWM block drives servo and brushed-motor actuators while its dual 10-bit ADC samples thermistor, humidity, and pressure sensors concurrently. The HCS12 core at 25 MHz delivers deterministic interrupt response needed for closed-loop temperature control, and 128 KB Flash holds look-up tables, PID control loops, and CAN stack for HVAC network communication. Because HVAC units operate across -40C to +85C ambient, the part's automotive temperature grade is suitable. The 112-LQFP package allows efficient PCB layout with thermal vias under the exposed pad to dissipate quiescent heat.
Рекомендуется
Instrument Cluster Controller
Instrument clusters require real-time stepper or DC motor control for analog gauges, plus CAN/LIN communication with the vehicle network. The MC9S12DJ128CPVE offers the 16-bit HCS12 core at 25 MHz with 8-channel PWM for gauge drive and dual 10-bit ADCs for fuel-level and temperature sensing. Its 20 digital I/O lines handle keypad inputs, indicator LEDs, and backlight dimming via PWM. 128 KB Flash accommodates gauge calibration tables, odometer storage in EEPROM, and the CAN/LIN stack. The 112-LQFP package provides sufficient pin count for stepper motor phases, display driver interfaces, and diagnostic LEDs.
Рекомендуется
Industrial CAN Node
The MC9S12DJ128CPVE serves as a CAN node in industrial automation networks where deterministic real-time response and on-chip analog peripherals are valued. Its HCS12 core at 25 MHz handles CANopen or DeviceNet protocol stacks, while the dual 10-bit ADC samples 4-20 mA industrial sensors through current-sense resistors. The 8-channel PWM can drive proportional valves or solid-state relays, and 128 KB Flash holds stack libraries plus application logic. SPI and I2C peripherals connect to external ADCs, DACs, or EEPROM for data logging. The 112-LQFP is industrial-standard surface-mount footprint compatible with pick-and-place assembly.
Рекомендуется
Battery Management Peripheral
Battery management systems (BMS) require multiple ADC channels for cell voltage and current sensing, plus CAN communication with the vehicle or pack controller. The MC9S12DJ128CPVE's dual 8-channel 10-bit ADC can sample up to 16 cell voltages with external muxing, while the 8-channel PWM drives cell-balancing FETs. The HCS12 core at 25 MHz handles SOC/SOH algorithms and CAN diagnostics within 128 KB Flash. Its automotive temperature grade supports under-hood deployment. The 112-LQFP package accommodates all analog, PWM, and CAN signals with proper grounding.
Рекомендуется
Motor Control / Pump Driver
DC and BLDC pump motors in automotive and industrial settings benefit from the MC9S12DJ128CPVE's 8-channel PWM block with complementary outputs and dead-time insertion, plus dual 10-bit ADC channels for current sensing via shunt resistors. The HCS12 core at 25 MHz runs field-oriented control (FOC) algorithms at adequate update rates for small motors. The 128 KB Flash holds motor-control firmware, fault handling, and CAN diagnostics. Integrated SCI, SPI, and I2C simplify communication with external gate drivers and position sensors. The 112-LQFP provides enough pins for three-phase signals plus encoder inputs.
Рекомендуется
Appliance Control Board
White goods and small appliances use the MC9S12DJ128CPVE as a single-chip controller combining user-interface key scanning, sensor acquisition, motor/valve actuation, and display driving. The 16-bit HCS12 core at 25 MHz handles UI state machines, while the dual 10-bit ADC reads temperature, humidity, or weight sensors. The 8-channel PWM drives pumps, valves, and buzzer tones. The two SCI (UART) channels can interface with wireless modules or external displays. The 112-LQFP package supports SMT assembly in cost-sensitive consumer designs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S12DJ128CPVE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S12DJ128MPVE | MC9S12DT256CPVE | MC9S12DP512CPVE | MC9S12DT256VPVE | MC9S12H256VFVE |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 112-LQFP (20x20) | 112-LQFP (20x20) - same | 112-LQFP (20x20) - same | 112-LQFP (20x20) - same | 112-LQFP (20x20) - same | 112-LQFP (20x20) - same |
| Core | HCS12, 16-bit | HCS12, 16-bit | HCS12, 16-bit | HCS12, 16-bit | HCS12, 16-bit | HCS12, 16-bit |
| Flash Memory | 128 KB | 128 KB | 256 KB | 512 KB | 256 KB | 256 KB |
| Max Clock Frequency | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| PWM Channels | 8 | 8 | 8 | 8 | 8 | 8 |
| ADC | 2 x 8-channel 10-bit | 2 x 8-channel 10-bit | 2 x 8-channel 10-bit | 2 x 8-channel 10-bit | 2 x 8-channel 10-bit | 2 x 8-channel 10-bit |
| Lifecycle Status | NRND | NRND | Active | Active | NRND | Active |
Ключевые отличия
- HCS12 16-bit core with dual 10-bit ADC and 8-channel PWM (против MC9S12H256VFVE)
- Lower Flash footprint reduces cost and silicon area (против MC9S12DP512CPVE)
- Dual SCI plus SPI/I2C for multi-bus connectivity (против MC9S12DT256VPVE)
Заметки по проектированию
The MC9S12DJ128CPVE integrates an on-chip voltage regulator with VDDR/VDDX pins. Decouple VDD with a 100 nF ceramic plus a 4.7 uF bulk capacitor placed within 5 mm of the supply pins; add separate 100 nF decoupling on each AVDD/VDDPLL pair. If using the internal regulator, drive VDDR from a clean 5 V source; for low-noise analog applications, consider external LDO for ADC supply rails.
Although the 112-LQFP package has moderate thermal resistance (theta_JA approximately 50 C/W on a 4-layer JEDEC board), sustained 25 MHz operation plus active ADC and PWM can push junction temperature close to the 125 C limit in enclosed automotive modules. Add thermal vias under the central thermal pad and route ground pour on the top layer to spread heat. Derate clock frequency if the enclosure ambient exceeds 85 C.
Place the external crystal within 10 mm of EXTAL/XTAL with symmetric traces and a ground guard ring; keep ADC traces away from PWM and digital switching signals to minimize coupling. Route the BKGD pin to a dedicated debug header with a 4.7 kohm pull-up to VDDX. The CAN TXCAN/RXCAN pair should be routed as a 100-ohm differential pair with ground shielding for reliable bus operation.
Because the part is NRND, do not start new automotive production designs without an explicit last-time-buy plan and a verified successor on the S12X or S12 MagniV families. When migrating to the MC9S12DT256CPVE or MC9S12DP512CPVE, re-validate linker scripts and interrupt vector tables because the larger Flash maps are slightly different. Verify BDM probe compatibility - some older P&E Micro cables require firmware updates for newer mask sets.
Информация о соответствии
Compliance status not explicitly stated in distributor listings retrieved 2026-10-20; verify against the NXP product declaration before RoHS/REACH-bound design.
