MC9S12NE64VTU - 16-bit HCS12 MCU 64KB Flash EMAC 80-TQFP-EP | NXP
Артикул: MC9S12NE64VTU ✓ АктивенMC9S12NE64VTU Обзор
A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash, RAM, EEPROM), and peripheral interfaces. The HCS12 family is a 16-bit CISC architecture widely used in automotive body, industrial control, and embedded networking applications because it offers deterministic interrupt behavior, a rich peripheral set, and broad toolchain support. The S12NE sub-family extends the base HCS12 with an integrated Ethernet MAC and PHY interface, making it a one-chip solution for industrial Ethernet nodes.
Key features of the MC9S12NE64VTU include a 25 MHz HCS12 core delivering 25 MIPS, 64KB Flash program memory with security features, 8KB RAM, an integrated 10/100 Ethernet MAC with MII interface for an external PHY, an 8-channel 10-bit ADC, multiple timers (ECT, PWM, TIM), SCI/SPI/I2C serial interfaces, and an operating voltage of 2.5 V core / 3.3 V I/O. The on-chip EMAC supports full-duplex operation and is designed to pair with a 100BASE-TX PHY such as the MC33660 or equivalent. The 80-TQFP-EP exposed-pad package enables improved thermal dissipation for continuous Ethernet operation.
The architecture is built on the proven HCS12 CPU with background debug mode (BDM), a memory protection unit option, and a flexible interrupt controller. The integrated Ethernet MAC offloads packet framing, CRC generation, and address filtering from the CPU, leaving sufficient cycles for application-layer processing at 10 Mbps and even modest 100 Mbps throughput. Operating temperature range is industrial grade, suitable for factory-floor equipment.
Typical applications include industrial Ethernet gateways, building automation controllers, BACnet/IP or Modbus TCP nodes, automotive body controllers with network connectivity, and remote sensor aggregation nodes. The wide HCS12 ecosystem means abundant CodeWarrior, GCC, and third-party IDE support.
Design consideration: pair the on-chip EMAC with a qualified 100BASE-TX PHY and ensure the MII traces are length-matched within 50 mils. The exposed pad must be soldered to a sufficient copper pour (>=1 sq inch) to keep junction temperature within spec during sustained MII traffic. Place a 0.1 uF decoupling capacitor within 5 mm of every VDD pin.
This page synthesizes distributor pricing, drop-in alternative cross-references, and design notes that supplement the manufacturer datasheet, giving engineers a single source for selection and sourcing decisions on the MC9S12NE64VTU.
Аналоги без доработки для MC9S12NE64VTU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S12NE64VTU (тот же форм-фактор и посадочное место) — отличается по Mounting Type, Operating Temperature, Serial Interfaces, Timers.
MC9S12NE64CFU
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MC9S12NE64VFU
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MC9S12NE100VTU
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MC9S12NE64VTU
✅ Прямая заменаУточнить цену
Открыть даташит →MC9S12NE64VTU Максимальные параметры и электрические характеристики
| Core Architecture | HCS12 (16-bit CISC) |
| CPU Speed | 25 MHz (25 MIPS) |
| Program Memory | 64 KB Flash |
| RAM | 8 KB |
| Operating Voltage (Core) | 2.5 V |
| Operating Voltage (I/O) | 3.3 V |
| Ethernet MAC | Integrated 10/100 EMAC with MII interface |
| ADC | 10-bit, 8-channel |
| Timers | ECT, PWM, TIM (8/16-bit) |
| Serial Interfaces | SCI (UART), SPI, I2C |
| Корпус | 80-TQFP-EP (14x14 mm) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +105C (industrial) |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Руководство по цоколевке MC9S12NE64VTU в корпусе 80-tqfp-ep (14x14 mm)
Цоколевка для MC9S12NE64VTU (корпус 80-tqfp-ep (14x14 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MC9S12NE64VTU.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MC9S12NE64VTU подходит для 6 применениеs: Industrial Ethernet Gateway, BACnet/IP Building Automation Controller, Automotive Body Control with Network Connectivity, Remote Sensor Aggregation Node, Modbus TCP to Serial Bridge, Embedded Web Server / HMI Controller.
Industrial Ethernet Gateway
The MC9S12NE64VTU's integrated 10/100 Ethernet MAC makes it a natural fit for industrial Ethernet gateways that bridge field devices to plant networks. The MAC handles packet framing, CRC, and address filtering, offloading work from the 25 MHz HCS12 core. With 64 KB Flash, it can run a compact TCP/IP stack (uIP or lwIP ported to HCS12) plus an application-layer protocol such as Modbus TCP or EtherNet/IP. The 8 KB RAM accommodates buffer pools for a single active socket, sufficient for sensor/actuator node traffic. Industrial temperature rating (-40C to +105C) supports factory-floor enclosures. Pair the MAC with an external 100BASE-TX PHY and ensure MII traces are length-matched within 50 mils on a 4-layer PCB.
Рекомендуется
BACnet/IP Building Automation Controller
BACnet/IP building controllers for VAV boxes, smart thermostats, and lighting nodes benefit from the MC9S12NE64VTU's integrated EMAC and modest 25 MIPS throughput. A BACnet/IP stack with trend logging, scheduling, and a few hundred objects fits comfortably in 64 KB Flash. The 10-bit ADC reads temperature, humidity, and CO2 sensors directly; PWM outputs drive damper actuators. With 8 KB RAM, the device can maintain BACnet COV subscriptions and a small read-group cache. Industrial-grade temperature tolerance supports unconditioned mechanical rooms. Time-stamped BACnet scheduling is easily served by the on-chip ECT timer module.
Рекомендуется
Automotive Body Control with Network Connectivity
The MC9S12NE64VTU is used in body-electronics modules that need Ethernet diagnostics alongside traditional CAN/LIN body control. The integrated EMAC supports service-tool Ethernet access (DoIP) while the SCI/SPI/I2C lines drive door modules, mirror controllers, and lighting. The 8-channel 10-bit ADC samples switch and sensor inputs at automotive-relevant rates. Operating range to +105C supports under-dash mounting. Compared to higher-end PowerPC body controllers, the HCS12 delivers lower cost per node for distributed body functions while maintaining automotive-grade reliability when sourced from automotive-qualified variants of the family.
Рекомендуется
Remote Sensor Aggregation Node
Distributed sensor networks for utility metering, environmental monitoring, and agricultural sensing benefit from the MC9S12NE64VTU's combination of EMAC connectivity and analog front-end. The 8-channel 10-bit ADC reads multiple sensor types; the EMAC reports aggregated data over 10/100 Ethernet. The 64 KB Flash holds a small MQTT-SN or custom UDP reporting stack, plus local calibration tables. With 8 KB RAM, the device can buffer samples during WAN outages and forward them when the network returns. The exposed thermal pad enables continuous MII operation without thermal throttling. Power-down modes (Stop/Wait) lower quiescent current for solar/battery-powered remote installations.
Рекомендуется
Modbus TCP to Serial Bridge
Industrial protocol converters that translate between Modbus TCP (Ethernet) and Modbus RTU (RS-485) are a classic application for the MC9S12NE64VTU. The integrated EMAC handles the Ethernet side, while the SCI drives an RS-485 transceiver for the legacy serial bus. With 64 KB Flash, the MCU can hold a Modbus TCP server, a Modbus RTU master/slave, and a configuration web server. The 8 KB RAM accommodates enough buffer space for typical register-mapping workloads. Industrial temperature rating and the exposed-pad thermal design make this part suitable for DIN-rail mounted installations in control cabinets.
Рекомендуется
Embedded Web Server / HMI Controller
Small-footprint embedded web servers for low-cost HMI panels, HVAC controllers, and machine-status displays leverage the MC9S12NE64VTU's integrated Ethernet plus its 10-bit ADC for analog feedback. A minimal HTTP server with CGI handlers fits in 64 KB Flash alongside a small HTML/CSS asset set. The PWM module drives LCD backlight dimming or LED indicators, while the ECT provides event timing for touch or rotary encoder inputs. Industrial temperature tolerance supports panel-mount applications. Compared to higher-end Cortex-M web servers, the HCS12 trades raw speed for deterministic interrupt latency and a long-life-cycle automotive pedigree.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S12NE64VTU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S12NE64CFU | MC9S12NE64VFU | MC9S12NE100VTU | MC9S12NE64CPV |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-TQFP-EP (14x14 mm) | 80-QFP - same family | 80-QFP - same family | 80-TQFP-EP - same package | 112-LQFP - different pin count |
| Flash Memory | 64 KB | 64 KB | 64 KB | 100 KB (+56%) | 64 KB |
| RAM | 8 KB | 8 KB | 8 KB | 12 KB (+50%) | 8 KB |
| CPU Speed | 25 MHz / 25 MIPS | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Ethernet MAC | Integrated 10/100 EMAC | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +105C (industrial) | 0C to +70C (commercial) | -40C to +105C (industrial) | -40C to +105C (industrial) | -40C to +105C (industrial) |
Ключевые отличия
- Integrated 10/100 Ethernet MAC with MII (против MC9S12DG256CPVE)
- Industrial temperature range as standard (против MC9S12NE64CFU)
- Long-life-cycle product with automotive pedigree (против MC9S12NE100VTU)
Заметки по проектированию
The MC9S12NE64VTU uses a 2.5 V core and 3.3 V I/O supply. Provide both rails from low-noise LDO regulators (e.g., NXP TLE4275 for 5V-to-3.3V). Place a 0.1 uF decoupling capacitor within 5 mm of every VDD/VDDR pin and a bulk 10 uF tantalum or ceramic capacitor on each supply rail. Core and I/O power sequencing should follow the datasheet section on power-on reset; tie RESET high via a 4.7 kohm pull-up and decouple with 1 nF to ground.
The 80-TQFP-EP exposed pad is the primary heat-dissipation path for sustained Ethernet MII traffic. Solder the EP to a copper pour of at least 1 square inch (645 sq mm) on the top side, with thermal vias (0.3 mm drill, 1 mm pitch) to an internal ground plane. Without adequate copper, junction temperature can exceed 105C at full CPU + EMAC load. Estimated: at 25 MHz core + active EMAC + 3.3V I/O, total power dissipation is approximately 0.6 W; with theta_JA around 35 C/W on a 4-layer JEDEC board, junction rises about 21C above ambient, requiring thermal management at high ambient (>80C) operation.
MII traces between the EMAC and external PHY must be length-matched within 50 mils (1.27 mm) and routed as 50 ohm controlled-impedance differential pairs on a 4-layer PCB with a solid ground plane beneath. Keep MII traces away from switching power supplies and clock generators. The 25 MHz oscillator traces should be short and guarded by ground. Place the PHY within 50 mm of the MCU to keep MII rise times within spec. Add series termination resistors (33 ohm) at the EMAC outputs if trace length exceeds 25 mm.
Do not omit the external PHY - the integrated EMAC is MAC-only and will not drive the magnetics directly. Ensure the BDM (background debug mode) pins have a debug header accessible for in-system programming; if not, field firmware updates are impossible. Avoid connecting the EMAC MDIO line directly to 5V logic; it is 3.3V only. The S12NE family requires the PLL to be configured for bus clock = oscillator clock / 2 at reset - incorrect PLL settings are a common boot failure.
Информация о соответствии
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified as standard; AEC-Q100 variants are available in the broader S12NE family with -Q suffix. Lead-free (Pb-free) reflow profile per JEDEC J-STD-020.
