MCP6004-E/ST - 1MHz Quad RRIO Op Amp | Microchip
Артикул: MCP6004-E/ST ✓ АктивенMCP6004-E/ST Обзор
An operational amplifier is an analog building block that amplifies the difference between two input voltages. In the broader semiconductor hierarchy, the MCP6004-E/ST is an operational amplifier, analog amplifier, and linear semiconductor. Its rail-to-rail inputs accept signals extending close to the positive and negative supply rails, while rail-to-rail outputs can swing close to those limits under suitable load conditions.
Key features include a 1 MHz gain-bandwidth product, 100 uA typical quiescent current, and operation across a 1.8 V to 5.5 V supply range. The device provides four amplifier channels in one package, reducing component count and board area for quad-signal paths. Its low-noise characteristics and 76 dB ESD protection make it appropriate for general-purpose analog front ends.
The MCP6004 family uses a low-power CMOS operational-amplifier architecture optimized for portable and embedded equipment. A 1 MHz bandwidth supports low-frequency signal amplification, filtering, buffering, and feedback control. The quad configuration allows four independent channels to share the same supply pins, simplifying power distribution while preserving channel-to-channel functional separation.
Typical applications include battery-powered sensor interfaces, buffered ADC inputs, current sensing, portable instrumentation, audio preamplification, and general feedback loops. The 1.8 V minimum supply voltage is especially useful for energy-harvesting, edge-sensing, and embedded systems operating from low-capacity batteries.
When designing around the MCP6004-E/ST, place each bypass capacitor close to the supply pins and route sensitive input traces away from switching nodes. Because the device is intended for general-purpose and low-frequency work, verify closed-loop stability, capacitive loading, output swing, and noise performance before using it in precision or high-bandwidth instrumentation.
This page combines the manufacturer specifications with package details, application guidance, and same-package amplifier comparisons. It helps engineers distinguish the standard MCP6004-E/ST from industrial-temperature, tape-ordering, and related amplifier variants before committing a 14-TSSOP design to production.
Аналоги без доработки для MCP6004-E/ST — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MCP6004-E/ST (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Number of Channels, Package.
MCP6004-I/ST
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6004T-I/ST
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6004T-E/STVAO
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP6024T-E/ST
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP602T-E/ST
✅ Прямая заменаУточнить цену
Открыть даташит →MCP6004-E/ST Максимальные параметры и электрические характеристики
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 1 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Ток покоя | 100 uA typical per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Bias Current | 1 pA typical |
| Input Offset Current | 1 pA typical |
| Input Offset Voltage | 4.5 mV typical |
| Voltage Noise Density | 28 nV/sqrt(Hz) at 1 kHz |
| Input Voltage Drift | 2 uV/C typical |
| Slew Rate | 600 V/ms |
| Диапазон рабочих температур | -40 C to +125 C |
| Корпус | 14-lead TSSOP |
| Package Width | 4.40 mm |
| Тип монтажа | Surface mount |
| ESD Protection | 76 dB |
| Статус RoHS | Compliant |
| Automotive Qualification | Not applicable |
Руководство по цоколевке MCP6004-E/ST в корпусе 4.40 mm
Цоколевка для MCP6004-E/ST (корпус 4.40 mm). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для MCP6004-E/ST.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MCP6004-E/ST подходит для 6 применениеs: Battery-Powered Sensor Signal Conditioning, Buffered ADC and DAC Interfaces, Portable Instrumentation and Measurement, Audio Preamplification and Headphone Buffers, Current Sensing and Power-Control Loops, Embedded IoT and Edge-Sensing Systems.
Battery-Powered Sensor Signal Conditioning
The MCP6004-E/ST fits battery-powered sensor front ends because it operates from 1.8 V to 5.5 V and draws 100 uA typical quiescent current per amplifier. Four channels can buffer sensor outputs, amplify strain-gauge or resistive-sensor signals, and provide active filtering without requiring a separate amplifier for each signal path. Rail-to-rail inputs are useful when the sensor output approaches the available supply range, although offset, bias current, and noise should be checked against the sensor source impedance.
Рекомендуется
Buffered ADC and DAC Interfaces
The MCP6004-E/ST can provide low-impedance drive for successive-approximation ADC inputs, DAC output buffers, and sample-and-hold isolation stages. Its 1 MHz gain-bandwidth product supports signal paths up to hundreds of kilohertz when closed-loop gain and stability requirements permit. Four independent channels make it practical to buffer several converter pins, while 100 uA typical quiescent current per channel helps control power in portable acquisition systems. Verify capacitive loading and settling time at the selected gain.
Рекомендуется
Portable Instrumentation and Measurement
For handheld meters, environmental monitors, and compact laboratory instruments, the MCP6004-E/ST combines four general-purpose channels with a 1.8 V minimum supply and 100 uA typical quiescent current. The amplifier can condition slow sensor signals, implement active low-pass filters, buffer resistive dividers, and drive control-loop inputs. Its 28 nV/sqrt(Hz) voltage-noise density at 1 kHz is a useful starting point for moderate-accuracy measurements, but precision designs must also account for 4.5 mV typical input offset.
Рекомендуется
Audio Preamplification and Headphone Buffers
The MCP6004-E/ST can serve as a low-noise preamplifier or buffer in portable audio paths when the desired signal bandwidth is below the 1 MHz gain-bandwidth product. Rail-to-rail input and output operation can improve utilization of low-voltage supplies, while four channels support stereo preamplification and auxiliary paths. Designers should check the 600 V/ms slew rate, output swing into the actual load, output-current capability, and channel noise at the audio frequencies of interest before finalizing the amplifier gain.
Рекомендуется
Current Sensing and Power-Control Loops
The MCP6004-E/ST is applicable to low-side current sensing, voltage-feedback control, and slow closed-loop power systems because it provides four channels, 1 MHz bandwidth, and rail-to-rail operation. It can amplify a small shunt voltage, buffer the result, compare feedback against a reference, and drive a slow correction stage. The 100 uA typical quiescent current is beneficial in battery systems, but input offset of 4.5 mV typical can dominate a small shunt measurement; calibration or a lower-offset family member may be necessary.
Рекомендуется
Embedded IoT and Edge-Sensing Systems
The MCP6004-E/ST fits edge-sensing modules that combine low-voltage analog measurements with embedded control. It can buffer resistive sensors, amplify photodiode or thermistor signals, implement gain stages, and provide active filtering before an embedded ADC. Operation from 1.8 V supports compact sensor nodes, and the quad package reduces component count. Because the 1 MHz bandwidth is modest, the part is best suited to slow environmental or industrial signals rather than wideband communications channels.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MCP6004-E/ST — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MCP6004-I/ST | MCP6004T-I/ST | MCP6004T-E/STVAO | MCP6024T-E/ST | MCP602T-E/ST |
|---|---|---|---|---|---|---|
| Package | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
Ключевые отличия
- Four low-power channels in one 14-TSSOP package (против MCP602T-E/ST)
- Direct same-family temperature-grade alternative (против MCP6004-I/ST)
- Rail-to-rail operation for low-voltage signal paths (против MCP6024T-E/ST)
Заметки по проектированию
Place the supply bypass capacitor directly between the VDD and VSS pins of the 14-TSSOP package. Keep input and feedback traces short, route them away from switching-regulator nodes, and use a continuous ground plane. The four amplifier channels share supply pins, so a single inadequate bypass capacitor can increase noise across every channel rather than affecting only one signal path.
Do not assume that a 1.8 V supply permits a full 1.8 V output swing. Check the MCP6004 output-voltage-versus-load curves and account for load current and temperature. Likewise, rail-to-rail input does not eliminate common-mode rejection errors or the 4.5 mV typical input offset, which can be significant when conditioning a millivolt-level sensor signal.
Check closed-loop stability with the actual source impedance, output capacitance, and load. A feedback resistor in the kilohm range combined with stray capacitance can create peaking even though the 1 MHz gain-bandwidth product is sufficient for the intended signal. Increase noise gain if necessary, add an isolation resistor, or select a higher-bandwidth amplifier when driving long cables or capacitive loads.
Estimated: each amplifier contributes 100 uA typical quiescent current, so four active channels require approximately 400 uA before load current. At a 3.3 V supply, the corresponding quiescent supply-current draw is approximately 1.32 mA and the ideal quiescent power is approximately 4.36 mW. Actual consumption also includes output-current demand and supply-dependent bias current.
Информация о соответствии
RoHS compliance is identified in the MCP6004-E/ST product listing. No manufacturer declaration confirming REACH, lead-free, halogen-free, or conflict-minerals status was identified.