MCP6004-E/ST - 1MHz Quad RRIO Op Amp | Microchip
MPN: MCP6004-E/ST ✓ 啟用中MCP6004-E/ST 概覽
An operational amplifier is an analog building block that amplifies the difference between two input voltages. In the broader semiconductor hierarchy, the MCP6004-E/ST is an operational amplifier, analog amplifier, and linear semiconductor. Its rail-to-rail inputs accept signals extending close to the positive and negative supply rails, while rail-to-rail outputs can swing close to those limits under suitable load conditions.
Key features include a 1 MHz gain-bandwidth product, 100 uA typical quiescent current, and operation across a 1.8 V to 5.5 V supply range. The device provides four amplifier channels in one package, reducing component count and board area for quad-signal paths. Its low-noise characteristics and 76 dB ESD protection make it appropriate for general-purpose analog front ends.
The MCP6004 family uses a low-power CMOS operational-amplifier architecture optimized for portable and embedded equipment. A 1 MHz bandwidth supports low-frequency signal amplification, filtering, buffering, and feedback control. The quad configuration allows four independent channels to share the same supply pins, simplifying power distribution while preserving channel-to-channel functional separation.
Typical applications include battery-powered sensor interfaces, buffered ADC inputs, current sensing, portable instrumentation, audio preamplification, and general feedback loops. The 1.8 V minimum supply voltage is especially useful for energy-harvesting, edge-sensing, and embedded systems operating from low-capacity batteries.
When designing around the MCP6004-E/ST, place each bypass capacitor close to the supply pins and route sensitive input traces away from switching nodes. Because the device is intended for general-purpose and low-frequency work, verify closed-loop stability, capacitive loading, output swing, and noise performance before using it in precision or high-bandwidth instrumentation.
This page combines the manufacturer specifications with package details, application guidance, and same-package amplifier comparisons. It helps engineers distinguish the standard MCP6004-E/ST from industrial-temperature, tape-ordering, and related amplifier variants before committing a 14-TSSOP design to production.
直接替換替代品,適用於 MCP6004-E/ST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP6004-E/ST (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Number of Channels, Package.
MCP6004-I/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6004T-I/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6004T-E/STVAO
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6024T-E/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP602T-E/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP6004-E/ST 最大額定值與電氣特性
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 1 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V |
| 靜態電流 | 100 uA typical per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Bias Current | 1 pA typical |
| Input Offset Current | 1 pA typical |
| Input Offset Voltage | 4.5 mV typical |
| Voltage Noise Density | 28 nV/sqrt(Hz) at 1 kHz |
| Input Voltage Drift | 2 uV/C typical |
| Slew Rate | 600 V/ms |
| 工作溫度範圍 | -40 C to +125 C |
| 封裝 | 14-lead TSSOP |
| Package Width | 4.40 mm |
| 安裝類型 | Surface mount |
| ESD Protection | 76 dB |
| RoHS 狀態 | Compliant |
| Automotive Qualification | Not applicable |
MCP6004-E/ST 4.40 mm 腳位配置指南
MCP6004-E/ST(4.40 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP6004-E/ST.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP6004-E/ST 適用於 6 應用s: Battery-Powered Sensor Signal Conditioning, Buffered ADC and DAC Interfaces, Portable Instrumentation and Measurement, Audio Preamplification and Headphone Buffers, Current Sensing and Power-Control Loops, Embedded IoT and Edge-Sensing Systems.
Battery-Powered Sensor Signal Conditioning
The MCP6004-E/ST fits battery-powered sensor front ends because it operates from 1.8 V to 5.5 V and draws 100 uA typical quiescent current per amplifier. Four channels can buffer sensor outputs, amplify strain-gauge or resistive-sensor signals, and provide active filtering without requiring a separate amplifier for each signal path. Rail-to-rail inputs are useful when the sensor output approaches the available supply range, although offset, bias current, and noise should be checked against the sensor source impedance.
推薦
Buffered ADC and DAC Interfaces
The MCP6004-E/ST can provide low-impedance drive for successive-approximation ADC inputs, DAC output buffers, and sample-and-hold isolation stages. Its 1 MHz gain-bandwidth product supports signal paths up to hundreds of kilohertz when closed-loop gain and stability requirements permit. Four independent channels make it practical to buffer several converter pins, while 100 uA typical quiescent current per channel helps control power in portable acquisition systems. Verify capacitive loading and settling time at the selected gain.
推薦
Portable Instrumentation and Measurement
For handheld meters, environmental monitors, and compact laboratory instruments, the MCP6004-E/ST combines four general-purpose channels with a 1.8 V minimum supply and 100 uA typical quiescent current. The amplifier can condition slow sensor signals, implement active low-pass filters, buffer resistive dividers, and drive control-loop inputs. Its 28 nV/sqrt(Hz) voltage-noise density at 1 kHz is a useful starting point for moderate-accuracy measurements, but precision designs must also account for 4.5 mV typical input offset.
推薦
Audio Preamplification and Headphone Buffers
The MCP6004-E/ST can serve as a low-noise preamplifier or buffer in portable audio paths when the desired signal bandwidth is below the 1 MHz gain-bandwidth product. Rail-to-rail input and output operation can improve utilization of low-voltage supplies, while four channels support stereo preamplification and auxiliary paths. Designers should check the 600 V/ms slew rate, output swing into the actual load, output-current capability, and channel noise at the audio frequencies of interest before finalizing the amplifier gain.
推薦
Current Sensing and Power-Control Loops
The MCP6004-E/ST is applicable to low-side current sensing, voltage-feedback control, and slow closed-loop power systems because it provides four channels, 1 MHz bandwidth, and rail-to-rail operation. It can amplify a small shunt voltage, buffer the result, compare feedback against a reference, and drive a slow correction stage. The 100 uA typical quiescent current is beneficial in battery systems, but input offset of 4.5 mV typical can dominate a small shunt measurement; calibration or a lower-offset family member may be necessary.
推薦
Embedded IoT and Edge-Sensing Systems
The MCP6004-E/ST fits edge-sensing modules that combine low-voltage analog measurements with embedded control. It can buffer resistive sensors, amplify photodiode or thermistor signals, implement gain stages, and provide active filtering before an embedded ADC. Operation from 1.8 V supports compact sensor nodes, and the quad package reduces component count. Because the 1 MHz bandwidth is modest, the part is best suited to slow environmental or industrial signals rather than wideband communications channels.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6004-E/ST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6004-I/ST | MCP6004T-I/ST | MCP6004T-E/STVAO | MCP6024T-E/ST | MCP602T-E/ST |
|---|---|---|---|---|---|---|
| Package | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP | 14-lead TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
主要差異化特點
- Four low-power channels in one 14-TSSOP package (對比MCP602T-E/ST)
- Direct same-family temperature-grade alternative (對比MCP6004-I/ST)
- Rail-to-rail operation for low-voltage signal paths (對比MCP6024T-E/ST)
設計說明
Place the supply bypass capacitor directly between the VDD and VSS pins of the 14-TSSOP package. Keep input and feedback traces short, route them away from switching-regulator nodes, and use a continuous ground plane. The four amplifier channels share supply pins, so a single inadequate bypass capacitor can increase noise across every channel rather than affecting only one signal path.
Do not assume that a 1.8 V supply permits a full 1.8 V output swing. Check the MCP6004 output-voltage-versus-load curves and account for load current and temperature. Likewise, rail-to-rail input does not eliminate common-mode rejection errors or the 4.5 mV typical input offset, which can be significant when conditioning a millivolt-level sensor signal.
Check closed-loop stability with the actual source impedance, output capacitance, and load. A feedback resistor in the kilohm range combined with stray capacitance can create peaking even though the 1 MHz gain-bandwidth product is sufficient for the intended signal. Increase noise gain if necessary, add an isolation resistor, or select a higher-bandwidth amplifier when driving long cables or capacitive loads.
Estimated: each amplifier contributes 100 uA typical quiescent current, so four active channels require approximately 400 uA before load current. At a 3.3 V supply, the corresponding quiescent supply-current draw is approximately 1.32 mA and the ideal quiescent power is approximately 4.36 mW. Actual consumption also includes output-current demand and supply-dependent bias current.
合規資訊
RoHS compliance is identified in the MCP6004-E/ST product listing. No manufacturer declaration confirming REACH, lead-free, halogen-free, or conflict-minerals status was identified.