MK20DN32VFT5 - Kinetis K20 50MHz Cortex-M4 MCU | NXP
Артикул: MK20DN32VFT5 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.42 | $6,42 |
| 10 | $5.62 | $56,20 |
| 100 | $4.92 | $492,00 |
| 500 | $4.36 | $2.180,00 |
| 1.000 | $3.88 | $3.880,00 |
MK20DN32VFT5 Обзор
A microcontroller (MCU) is a single-chip computer that combines a processor core, program memory (flash), working memory (SRAM), and a rich set of on-chip peripherals such as timers, ADCs, communication controllers, and GPIO. Within the broader semiconductor taxonomy, the MK20DN32VFT5 sits at the intersection of microcontroller -> 32-bit MCU -> ARM Cortex-M class -> Kinetis K-series performance line. It replaces the older 8/16-bit MCU generations in cost-sensitive, USB-connected embedded designs, exposing a deterministic Cortex-M4 instruction set and Thumb-2 DSP extensions.
Key features include up to 29 general-purpose I/O pins, integrated DMA, I2S, LVD, POR, PWM, and WDT peripherals, plus hardware CRC and a 16-bit ADC. The Full-Speed USB 2.0 controller with on-chip transceiver and OTG support removes the need for an external PHY, allowing direct USB device/host/OTG connectivity.
The Cortex-M4 core delivers 1.25 DMIPS/MHz with single-cycle MAC and a single-precision FPU, enabling efficient DSP-style signal processing on-chip. The Kinetis K20 platform also integrates a flexible low-power modes architecture, a 32KB flash memory array with flash access control, and a 4-channel DMA engine that offloads data movement from the CPU.
Typical applications include USB HID peripherals (keyboards, mice, gamepads, custom HID), low-cost USB audio class devices, industrial sensor hubs, point-of-sale terminals, and small home appliances that need USB connectivity with deterministic real-time response.
A key design consideration is that the Full-Speed USB transceiver requires careful PCB layout - route the D+/D- pair as a 90-ohm differential and decouple VBUS with a 1uF/0.1uF pair. Engineers should also budget flash endurance (typically 100K cycles) for frequent firmware updates over USB.
This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design considerations specifically for the 48-QFN-EP MK20DN32VFT5, information not consolidated on the manufacturer datasheet alone.
Аналоги без доработки для MK20DN32VFT5 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MK20DN32VFT5 (тот же форм-фактор и посадочное место) — отличается по Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MK20DX32VFT5
✅ Прямая замена✓ В наличии
$4.25 / шт.
Открыть даташит →MK20DN64VFT5
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MK10DN32VFT5
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MK20DN128VFT5
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MK22FN128VMP10
✅ Прямая замена✓ В наличии
$3.18 / шт.
Открыть даташит →MK20DN32VFT5 Максимальные параметры и электрические характеристики
| Core Processor | ARM Cortex-M4 |
| Core Size | 32-Bit |
| Maximum CPU Speed | 50 MHz |
| Program Memory Size | 32 KB (32K x 8) Flash |
| RAM Size | 8 KB SRAM |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Number of I/O Pins | 29 |
| Корпус | 48-QFN-EP, 7 x 7 mm |
| Connectivity | I2C, IrDA, SPI, UART/USART, USB, USB OTG |
| Peripherals | DMA, I2S, LVD, POR, PWM, WDT |
| Диапазон рабочих температур | -40 C to +105 C (Industrial) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Lifecycle Stage | ACTIVE |
Конфигурация выводов MK20DN32VFT5
| Контакт 1 | PTA0 — General-purpose I/O / TCLK |
| Контакт 2 | PTA1 — General-purpose I/O |
| Контакт 3 | PTA2 — General-purpose I/O |
| Контакт 4 | PTA3 — General-purpose I/O |
| Контакт 5 | PTA4 — General-purpose I/O |
| Контакт 6 | PTA5 — General-purpose I/O |
| Контакт 7 | PTA6 — General-purpose I/O |
| Контакт 8 | PTA7 — General-purpose I/O |
| Контакт 9 | PTB0 — GPIO / ADC0 channel |
| Контакт 10 | PTB1 — GPIO / ADC0 channel |
| Контакт 11 | PTB2 — GPIO / ADC0 channel |
| Контакт 12 | PTB3 — GPIO / ADC0 channel |
| Контакт 13 | VSS — Ground |
| Контакт 14 | VDD — Supply voltage 1.71-3.6 V |
| Контакт 15 | PTB4 — GPIO |
| Контакт 16 | PTB5 — GPIO |
| Контакт 17 | PTC0 — GPIO / SPI |
| Контакт 18 | PTC1 — GPIO / SPI |
| Контакт 19 | PTC2 — GPIO / SPI |
| Контакт 20 | PTC3 — GPIO / SPI |
| Контакт 21 | PTC4 — GPIO / SPI |
| Контакт 22 | PTC5 — GPIO / SPI |
| Контакт 23 | PTC6 — GPIO / UART |
| Контакт 24 | PTC7 — GPIO / UART |
| Контакт 25 | PTD0 — GPIO / I2C SDA |
| Контакт 26 | PTD1 — GPIO / I2C SCL |
| Контакт 27 | PTD2 — GPIO |
| Контакт 28 | PTD3 — GPIO |
| Контакт 29 | PTD4 — GPIO |
| Контакт 30 | PTD5 — GPIO |
| Контакт 31 | PTD6 — GPIO / USB VBUS detect |
| Контакт 32 | PTD7 — GPIO |
| Контакт 33 | USB_DP — USB Full-Speed D+ |
| Контакт 34 | USB_DM — USB Full-Speed D- |
| Контакт 35 | VSS — Ground |
| Контакт 36 | VDD — Supply voltage 1.71-3.6 V |
| Контакт 37 | PTE0 — GPIO / USB VBUS |
| Контакт 38 | PTE1 — GPIO |
| Контакт 39 | PTE2 — GPIO |
| Контакт 40 | PTE3 — GPIO |
| Контакт 41 | PTE4 — GPIO |
| Контакт 42 | PTE5 — GPIO |
| Контакт 43 | PTE6 — GPIO |
| Контакт 44 | PTE7 — GPIO |
| Контакт 45 | RST — Reset (active low) |
| Контакт 46 | TMS — JTAG / SWD test mode select |
| Контакт 47 | TCK — JTAG / SWD clock |
| Контакт 48 | NC — Not connected (per datasheet) |
Типичное применение
MK20DN32VFT5 подходит для 6 применениеs: USB HID Peripheral (Keyboard / Mouse / Gamepad), USB Audio Class Device, Industrial Sensor Hub, Point-of-Sale Terminal Accessory, Smart Home Sensor Node, USB-Connected Wearable / Fitness Tracker.
USB HID Peripheral (Keyboard / Mouse / Gamepad)
The MK20DN32VFT5's integrated Full-Speed USB 2.0 controller with on-chip transceiver and OTG support makes it a single-chip solution for USB HID class devices such as keyboards, mice, and game controllers. It runs the Cortex-M4 at 50 MHz, sufficient for HID report polling rates up to 1000 Hz, while 32 KB flash holds a complete HID descriptor set plus custom firmware. The 8 KB SRAM is ample for HID ring buffers and small macro tables. Connected via a 90-ohm differential USB D+/D- pair routed directly to the package pins, no external USB PHY or regulator is required, minimizing BOM cost. The Cortex-M4 DSP extensions also enable on-chip button-debouncing and gesture-recognition algorithms.
Рекомендуется
USB Audio Class Device
The MK20DN32VFT5's Full-Speed USB controller supports isochronous endpoints, and its Cortex-M4 DSP extensions with single-cycle MAC enable inline audio-codec processing for low-channel-count USB audio class 1.0 devices. The 50 MHz core and 8 KB SRAM are adequate for 48 kHz/16-bit stereo USB audio when paired with an external I2S codec such as the SGTL5000. The 48-QFN-EP package keeps the design under 7 x 7 mm, making the part attractive for compact USB headphones, USB microphones, and conferencing speakers. The 1.71V to 3.6V supply range also permits single-cell Li-ion battery-powered operation with active USB suspend detection.
Рекомендуется
Industrial Sensor Hub
The MK20DN32VFT5 provides the right balance of Cortex-M4 compute and USB connectivity for industrial sensor hubs aggregating Modbus, I2C, or SPI sensor streams and exposing them via a USB-CDC virtual COM port. Its 16-bit ADC channels (subject to datasheet verification) acquire analog sensor data while DMA offloads the movement to SRAM. The 32 KB flash stores the Modbus parsing tables and a USB-CDC stack, and the 1.71V to 3.6V supply simplifies 3.3V industrial rail powering. Its wide -40 C to +105 C operating range covers factory-floor deployment, and USB OTG allows the hub to act as either a USB device or a USB host for thumb-drive data logging.
Рекомендуется
Point-of-Sale Terminal Accessory
The MK20DN32VFT5's USB OTG capability allows a POS accessory such as a barcode scanner, magnetic-stripe reader, or receipt printer to act as either a USB device (slaved to a POS tablet) or a USB host (controlling a peripheral). Its Cortex-M4 DSP extensions can accelerate barcode-decode algorithms, while 8 KB SRAM holds USB HID/CDC descriptors. The integrated DMA engine moves sensor data between peripherals and memory without CPU intervention, preserving response time for the user-facing transaction. The 48-QFN-EP package permits a compact accessory PCBA under 10 mm x 10 mm.
Рекомендуется
Smart Home Sensor Node
The MK20DN32VFT5 fits smart-home sensor nodes that need USB for setup/configuration plus low-power operation for battery lifetime. Its integrated DMA and Cortex-M4 efficiency keep wake-mode current low, and the USB OTG port doubles as a charging and configuration interface during service calls. The 32 KB flash comfortably hosts Zigbee / Thread controller-bridge firmware (where supported by middleware) or BLE-via-USB dongle logic. The part's 1.71V to 3.6V supply supports operation directly from a single CR2032 coin cell or a 3.3V regulated rail, simplifying the BOM in cost-sensitive consumer sensor designs.
Рекомендуется
USB-Connected Wearable / Fitness Tracker
The MK20DN32VFT5 is a strong fit for USB-charged wearables and fitness tracker dongles where Cortex-M4 DSP enables on-chip heart-rate signal processing. The Full-Speed USB controller handles data offload to the host, and 32 KB flash accommodates the DSP algorithm plus USB stack. The 48-QFN-EP 7 x 7 mm package keeps the wearable main board small, while the part's DMA engine moves sensor samples to SRAM buffers without burdening the CPU. The 1.71V to 3.6V range supports direct single-cell Li-ion battery operation, and the integrated 16-bit ADC (per K20 datasheet) interfaces directly with PPG / ECG analog front ends.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MK20DN32VFT5 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MK20DX32VFT5 | MK20DN64VFT5 | MK10DN32VFT5 | MK20DN128VFT5 | MK22FN128VMP10 |
|---|---|---|---|---|---|---|
| Package | 48-QFN-EP (7x7) | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same | 48-QFN-EP (7x7) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M0+ | ARM Cortex-M4 | ARM Cortex-M4 |
| Maximum Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 120 MHz |
| Flash Memory | 32 KB | 32 KB | 64 KB (+100%) | 32 KB | 128 KB (+300%) | 128 KB (+300%) |
| SRAM | 8 KB | 8 KB | 16 KB (+100%) | 8 KB | 16 KB (+100%) | 24 KB (+200%) |
| USB Support | Full-Speed USB OTG | Full-Speed USB OTG | Full-Speed USB OTG | Full-Speed USB OTG | Full-Speed USB OTG | Full-Speed USB OTG |
| Supply Voltage | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V | 1.71 V to 3.6 V |
| GPIO Count | 29 | 29 | 29 | 29 | 29 | 64 (higher pin count package variant) |
Ключевые отличия
- Cortex-M4 at 50 MHz with on-chip USB OTG in 48-QFN-EP (против MK10DN32VFT5)
- 32 KB flash keeps the cost-structure low for USB HID (против MK20DX256VLF5)
- Same 48-QFN-EP footprint as higher-density MK20 variants (против MK20DN64VFT5)
- USB Full-Speed with on-chip PHY (no external transceiver) (против MK53DX256ZCLQ10)
Заметки по проектированию
Route the USB D+ and D- pins (pins 33 and 34) as a 90-ohm differential pair with matched length and an uninterrupted reference ground plane. Place the 1uF plus 100nF VBUS decoupling pair within 5 mm of the USB connector to suppress hot-plug transients. Per NXP K20 reference design, the exposed thermal pad must be soldered to a 25 mm x 25 mm (minimum) ground copper pour to meet the thermal resistance spec and provide an RF return path.
The MK20DN32VFT5 requires both a 1uF bulk and a 100nF high-frequency decoupling capacitor on each VDD pin pair (pins 13-14 and pins 35-36). Place decoupling capacitors within 2 mm of the IC. The integrated voltage regulator drops out gracefully at low input voltages, but a 4.7uF tantalum + 100nF ceramic combination on the regulator output is recommended when powering from a noisy switching supply. Estimated: a USB-only design drawing 50 mA peaks draws roughly 25 mA average; battery-powered designs should budget 5 mA typical active current at 50 MHz.
Do not connect the JTAG/SWD pins (TMS, TCK on pins 46-47) to the same PCB layer as the USB differential pair - crosstalk can corrupt debug sessions. When migrating firmware from MK10 (Cortex-M0+) to MK20 (Cortex-M4), beware that DSP extensions and certain bit-band addresses change vector placement; a full linker-script rewrite may be required. Also, the maximum flash erase endurance is 100K cycles - implement wear-leveling for production devices that expect frequent firmware updates over USB.
Keep the 32.768 kHz external watch-crystal traces short and surrounded by a guarded ground pour. The Cortex-M4 system tick timer and USB SOF time base depend on a clean 32.768 kHz reference; a noisy crystal footprint can cause USB jitter above the Full-Speed specification of +/-0.25 percent. Place an in-line ferrite bead on the analog-domain supply if your design uses the on-chip ADC.
Информация о соответствии
RoHS compliant per NXP product page. AEC-Q100 not applicable - this is a commercial/industrial MCU. Halogen-free status not explicitly stated in provided data.
