MSP430F2101TPW - 16MHz Ultra-Low-Power MCU | Texas Instruments
Артикул: MSP430F2101TPW ✓ АктивенMSP430F2101TPW Обзор
An ultra-low-power mixed-signal microcontroller combines a low-power digital processing core with analog peripherals capable of measuring or comparing voltage signals. The MSP430F2101 belongs to the MSP430 family, where its 16-bit RISC CPU, 16-bit registers, and low-power operating modes support portable measurement systems that capture analog signals, convert them into digital information, and process or transmit the results.
Key features include a 16 MHz maximum clock speed, 1 KB of Flash memory, and 128 B of SRAM. The device has 16 I/O pins, a built-in 16-bit timer, and a versatile analog comparator. Low-power figures include 250 µA active current at 1 MHz and 2.2 V, 0.7 µA in standby mode, and 0.1 µA in off mode with RAM retention. Wake-up from standby takes less than 1 µs.
The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers and supports several low-power operating modes. Its fast standby wake-up allows a system to remain in a low-consumption state between measurements and quickly resume processing when a sensor, timer, or comparator event requires attention. The mixed-signal resources reduce the need for external analog and timing components in compact designs.
Typical applications include portable sensor systems, battery-powered instrumentation, low-level signal acquisition, threshold detection, and host-connected measurement equipment. The 20-pin TSSOP package also supports mixed-signal products that require analog comparison and timed control while keeping the component count low. Its 1.8 V minimum operating voltage supports compatibility with modern low-energy sensor and embedded-control systems.
PCB design should place decoupling capacitance close to the supply pins, route sensitive analog inputs away from fast digital switching paths, and preserve the recommended grounding and layout geometry from the manufacturer datasheet. Firmware should also use the MSP430 low-power modes deliberately, because sleep timing and retained peripheral state directly influence the achievable standby and off-mode current.
This product page combines the MSP430F2101TPW specifications, package details, application guidance, and verified same-family replacement options into an engineering-focused reference. It helps designers evaluate the 16 MHz mixed-signal MCU for low-power sensor, timer, comparator, and portable measurement designs without confusing pin-compatible options with unrelated microcontrollers.
Аналоги без доработки для MSP430F2101TPW — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MSP430F2101TPW (тот же форм-фактор и посадочное место) — отличается по Flash Memory, SRAM, Product Type, Package, Timer.
MSP430F2101IPW
✅ Прямая заменаУточнить цену
Открыть даташит →MSP430F2121TPW
✅ Прямая заменаУточнить цену
Открыть даташит →MSP430F2121IPW
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MSP430F2111TPW
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MSP430F2111IPW
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MSP430F2101TPW Максимальные параметры и электрические характеристики
| CPU Architecture | 16-bit RISC |
| Максимальная тактовая частота | 16 MHz |
| Flash Memory | 1 KB |
| SRAM | 128 B |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Active Current | 250 µA at 1 MHz and 2.2 V |
| Standby Current | 0.7 µA |
| Off Current | 0.1 µA with RAM retention |
| Standby Wake-Up Time | Less than 1 µs |
| GPIO Count | 16 pins |
| Timer | 16-bit timer |
| Analog Comparator | 1 integrated analog comparator |
| Корпус | 20-pin TSSOP (PW) |
| Package Width | 4.40 mm |
| Package Length | 0.173 in |
| Тип монтажа | Surface mount |
Руководство по цоколевке MSP430F2101TPW в корпусе 0.173 in
Цоколевка для MSP430F2101TPW (корпус 0.173 in). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MSP430F2101TPW.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MSP430F2101TPW подходит для 6 применениеs: Portable Sensor Measurement, Battery-Powered Industrial Monitoring, Threshold Detection and Control, Compact Data-Acquisition Module, Low-Power Utility Metering, Portable Medical Sensor Interface.
Portable Sensor Measurement
The MSP430F2101TPW fits portable sensor nodes that sample low-level signals, perform threshold decisions, and remain inactive between events. Its 16 MHz MSP430 CPU provides processing capacity for digital filtering and control, while the 16-bit timer supports periodic sampling. The low-power specification of 250 µA active at 1 MHz and 2.2 V, 0.7 µA standby, and 0.1 µA off with RAM retention helps reduce battery load. Its 16 GPIO pins and analog comparator permit sensor interfaces and local threshold detection without requiring a separate peripheral controller.
Рекомендуется
Battery-Powered Industrial Monitoring
The MSP430F2101TPW is appropriate for isolated industrial monitoring equipment that periodically measures a sensor and reports status. Its 1.8 V to 3.6 V operating range supports low-energy supply rails, and standby wake-up in less than 1 µs enables rapid response to timer or comparator events. The 16-bit timer can establish measurement intervals, while the analog comparator can detect threshold crossings. Firmware can use the low-power modes between samples, reducing the energy cost of maintaining an always-active acquisition system in factory or field instrumentation.
Рекомендуется
Threshold Detection and Control
The MSP430F2101TPW can act as a compact threshold-detection controller by using its integrated analog comparator to monitor a sensor signal. The 16 GPIO pins support digital inputs, alarm outputs, and external control functions, while the 16-bit timer provides repeatable event timing. With a 16 MHz CPU, the device can execute filtering, hysteresis, debounce, and communication logic after a comparator event. Its standby current of 0.7 µA helps preserve battery life while the controller waits continuously for a threshold crossing.
Рекомендуется
Compact Data-Acquisition Module
The MSP430F2101TPW is suitable for compact data-acquisition modules that must acquire, validate, and forward measurements to a host. The 16-bit timer establishes accurate sampling intervals, the comparator supports range or threshold supervision, and the 16 GPIO pins provide digital interfaces. Although the 1 KB Flash and 128 B SRAM are modest, they are practical for small firmware images and short buffering workloads. The 20-pin TSSOP keeps the footprint compact, and the less-than-1-µs standby wake-up supports rapid duty-cycled acquisition sequences.
Рекомендуется
Low-Power Utility Metering
The MSP430F2101TPW can serve as the control core of a low-power utility or energy meter with limited computation requirements. Its 16-bit CPU can calculate consumption data, the timer can generate measurement windows, and the GPIO pins can support pulse, alarm, or status inputs. The microcontroller operates from a supply as low as 1.8 V and can remain in standby at 0.7 µA between measurement intervals. This makes the device useful for compact metering modules where continuous operation would waste energy, provided the selected memory variant satisfies the code and data-storage requirements.
Рекомендуется
Portable Medical Sensor Interface
The MSP430F2101TPW can support a portable biomedical sensor interface when the design requires local signal supervision, timing, and control. The analog comparator can perform fast threshold detection, the 16-bit timer can coordinate sampling, and the 16 GPIO pins can connect sensor enables, status indicators, and digital controls. Its low-power operating modes are valuable in wearable or battery-operated monitoring equipment because standby current is 0.7 µA and wake-up is less than 1 µs. Clinical designs still require appropriate isolation, protection, accuracy validation, and regulatory review beyond the MCU specification.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MSP430F2101TPW — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MSP430F2101IPW | MSP430F2121TPW | MSP430F2121IPW | MSP430F2111TPW | MSP430F2111IPW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) | 20-pin TSSOP (PW) |
| CPU Architecture | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Analog Comparator | Integrated | Integrated | Integrated | Integrated | Integrated | Integrated |
Ключевые отличия
- Directly matches the MSP430F2101 configuration (против MSP430F2101IPW)
- Lower memory profile within the same mixed-signal family (против MSP430F2121TPW)
- Very low standby consumption for duty-cycled sensing (против MSP430F2121TPW)
- Fast recovery from standby (против MSP430F2101IPW)
Заметки по проектированию
Place the supply decoupling capacitor immediately adjacent to the device supply and ground pins, and follow the manufacturer datasheet layout example for the 20-pin PW package. Keep the analog comparator input traces short, route them away from digital output edges, and use a continuous ground reference beneath the device where the package and board construction permit it.
Design the firmware around the MSP430 low-power modes rather than using a busy-wait loop. The device can consume 250 µA in active mode at 1 MHz and 2.2 V, compared with 0.7 µA in standby and 0.1 µA in off mode with RAM retention. Retain only the state needed after wake-up, disable unused peripherals, and confirm that timer or comparator events can restart the required measurement sequence.
Do not assume that every MSP430x21x1 memory variant is interchangeable without checking code size, RAM usage, and interrupt-vector requirements. The MSP430F2101TPW has 1 KB Flash and 128 B SRAM, so buffer-intensive or protocol-heavy firmware may require a larger-memory variant. Also verify reset, programming-test, clock, and supply pins against the exact manufacturer pin-description table before release.
Информация о соответствии
Compliance attributes were not explicitly stated in the manufacturer product-page snippets or distributor listings. Review the current Texas Instruments product and quality documentation before approving the device for a regulated design.