NTSX2102 - 2-Bit Open-Drain Level Translator | NXP | I2C
Артикул: NTSX2102 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
NTSX2102 Обзор
A dual-supply translating transceiver is a class of level-shifter IC within the broader hierarchy of logic ICs and voltage translators. It bridges two independently powered domains - for example a 1.8V microcontroller and a 3.3V peripheral - by translating logic thresholds between a VCC(A) side and a VCC(B) side. Open-drain architectures are specifically suited to shared buses such as I2C and 1-wire, where lines are pulled high by external resistors and any device can drive them low, requiring no explicit direction control signal.
The NTSX2102's headline features are automatic direction sensing (no DIR pin required), an output enable input (OE) that tri-states both ports for bus isolation or power-down, and an open-drain output structure purpose-built for I2C, SMBus-style and 1-wire point-to-point links. Two 2-bit input/output port pairs (A1/A2 and B1/B2) provide the translation channels.
According to the NXP product data sheet, the device is targeted at point-to-point applications interfacing devices or systems operating at different supply voltages, using open-drain drivers. The auto-direction-sensing topology detects which side is driving and propagates the transition to the opposite side, eliminating firmware direction management. The 50 Mbit/s capability comfortably covers Standard, Fast and Fast-mode Plus I2C speeds as well as faster proprietary 2-wire links.
Typical applications include I2C bus level translation between 1.8V/3.3V domains, 1-wire EEPROM and authentication IC links, low-voltage sensor interfaces in portable and battery-powered systems, and general-purpose open-drain signaling where footprints of a few square millimeters matter.
Design consideration: open-drain translation requires external pull-up resistors on both sides; choose pull-up values that balance rise time (bus capacitance) against static current, and ensure the A-side supply is not below the device minimum - an NXP community thread notes operation starts from 1.65 V on the A-side, so 1.2 V domains need a different part.
This page synthesizes distributor listings, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для NTSX2102 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
Для этого товара нет аналогов без доработки.
Запросить аналогиNTSX2102 Максимальные параметры и электрические характеристики
| Функция | Dual supply translating transceiver |
| Bit Width | 2 bit |
| Тип выхода | Open-drain |
| Direction Control | Auto direction sensing |
| Скорость передачи данных | 50 Mbit/s |
| Каналы | 2 bidirectional channels (A1/A2 to B1/B2) |
| Output Enable | Yes (OE input) |
| Supply Pins | VCC(A) and VCC(B) dual supply |
| Targeted Buses | I2C, 1-wire (open-drain drivers) |
| A-Side Supply Minimum | 1.65 V (per NXP community clarification) |
| Package (GU8H) | 8-pin XQFN, 1.4 x 1.2 mm |
| Тип монтажа | Surface Mount |
Руководство по цоколевке NTSX2102 в корпусе 8-pin xqfn, 1.4 x 1.2 mm
Цоколевка для NTSX2102 (корпус 8-pin xqfn, 1.4 x 1.2 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для NTSX2102.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
NTSX2102 подходит для 6 применениеs: I2C Bus Level Translation, 1-Wire Bus Interfacing, Point-to-Point Board Interconnect, Portable and Battery-Powered Devices, Sensor Interface Level Shifting, Industrial Control and Automation.
I2C Bus Level Translation
The NTSX2102's primary application is level-shifting an I2C bus between two voltage domains, for example a 1.8 V microcontroller (VCC(A) side) and a 3.3 V sensor or EEPROM (VCC(B) side). Its open-drain output structure mirrors the native I2C electrical convention: any device on either side can pull SDA/SCL low, and the auto-direction-sensing circuitry propagates the transition to the opposite domain without a DIR pin or firmware intervention. With a 50 Mbit/s capability, the device covers Standard, Fast and Fast-mode Plus I2C with wide margin; the practical speed limit is set by pull-up resistors and bus capacitance. External pull-ups to each side's rail are required, and the OE pin allows the translator to be tri-stated during power sequencing so an unpowered side does not clamp the bus.
Рекомендуется
1-Wire Bus Interfacing
The NXP datasheet explicitly targets 1-wire buses using open-drain drivers, and the NTSX2102 is a natural fit for translating a 1-wire link between a low-voltage host and a higher-voltage peripheral such as an EEPROM, battery-identity IC or authentication device. The auto direction sensing handles the bidirectional time-slot signaling of 1-wire protocols: the host drives the line low for reset or write slots, and the slave answers by pulling the line low, with all transitions passing transparently through the translator. Because 1-wire is single-ended and open-drain, only one channel of the 2-bit device is consumed, leaving the second channel available for a companion 1-wire line or an auxiliary open-drain flag signal. External pull-up resistor sizing per the 1-wire specification governs achievable timing.
Рекомендуется
Point-to-Point Board Interconnect
Beyond named bus standards, the NTSX2102 suits general point-to-point interconnection between devices or systems operating at different supply voltages, as stated in the NXP general description. Examples include connecting a 1.8 V GPIO, interrupt or enable line from an application processor to a 3.3 V power-management IC, or bridging a 5 V-tolerant peripheral to a low-voltage FPGA bank. The two independent channels (A1/A2 and B1/B2) allow two such signals to cross a domain boundary through one 1.4 x 1.2 mm XQFN-8 footprint. The open-drain topology means each line needs a pull-up to its local rail, and the 50 Mbit/s bandwidth supports fast edge signaling well above typical GPIO rates. The OE input supports safe power-down of either domain.
Рекомендуется
Portable and Battery-Powered Devices
The 8-pin XQFN package of the NTSX2102GU8H measures only 1.4 x 1.2 mm, making the device attractive for smartphones, wearables, hearables and other battery-powered products where board area is the scarcest resource. Battery-powered systems routinely mix rails - a 1.8 V application processor, a 3.3 V fuel gauge or secure element, and a sensor at yet another voltage - and the NTSX2102's dual-supply, 2-bit architecture bridges one such boundary per package with automatic direction sensing that consumes no GPIO for direction control. The OE pin permits the translator to be disabled to eliminate leakage paths when a subsystem rail is powered down, supporting aggressive power gating. Its small die also contributes low added capacitance on the translated lines.
Рекомендуется
Sensor Interface Level Shifting
Modern sensors ship in a range of supply voltages, and the NTSX2102 lets a low-voltage MCU talk to a sensor rail without violating either device's absolute maximum ratings. In a typical arrangement, VCC(A) tracks the microcontroller IO rail (for example 1.8 V) and VCC(B) tracks the sensor rail (for example 3.3 V); the I2C SDA/SCL pair or a 2-wire status/interrupt pair crosses the NTSX2102 in one package. Auto direction sensing is essential here because sensor interrupt lines can be driven from either side and I2C is inherently bidirectional. Designers should confirm the sensor-side rail stays within the NTSX2102's B-side supply range per the datasheet, keep pull-ups sized to the sensor bus capacitance, and use OE to isolate the sensor rail during system standby.
Рекомендуется
Industrial Control and Automation
Industrial controllers frequently combine a low-voltage MCU core domain with 3.3 V or 5 V field-side signaling, and the NTSX2102 provides an orderly, dedicated crossing point for open-drain signals such as I2C-linked expansion ports, configuration interfaces, and 1-wire device identification (for example, board-serialization EEPROMs read by production test equipment). Its 50 Mbit/s headroom and 2-bit width let one device carry a full I2C pair, and its OE pin lets the controller isolate the field side while the backplane powers up - important in systems where a card is hot-inserted. The XQFN-8 footprint suits dense PLC I/O modules, and the open-drain structure tolerates multi-drop extensions on the B-side where the local bus protocol permits, provided total capacitance and pull-up strength are re-evaluated.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для NTSX2102 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | NTSX2102TLH | NTSX2102GU8H |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Bit Width | 2 bit | 2 bit | 2 bit |
| Output Type | Open-drain | Open-drain | Open-drain |
| Direction Control | Auto direction sensing | Auto direction sensing | Auto direction sensing |
| Data Rate | 50 Mbit/s | 50 Mbit/s | 50 Mbit/s |
| Output Enable (OE) | Yes | Yes | Yes |
| Targeted Buses | I2C, 1-wire (open-drain) | I2C, 1-wire (open-drain) | I2C, 1-wire (open-drain) |
| Drop-in on GU8H footprint | Reference | No - different package | Yes - same package |
Ключевые отличия
- Dedicated open-drain I2C/1-wire architecture (против NTSX2102TLH)
- Auto direction sensing with no DIR pin (против NTSX2102TLH)
- Honest trade-off: 1.65 V minimum A-side supply (против NTSX2102TLH)
Заметки по проектированию
The NTSX2102GU8H uses an 8-pin XQFN land pattern of only 1.4 x 1.2 mm. Follow the NXP footprint recommendation exactly, including any center thermal/electrical pad specified in the datasheet layout section, and place the 100 nF decoupling capacitor for each supply pin (VCC(A) and VCC(B)) within 1-2 mm of the respective pin. Because both supplies are independent, each must be decoupled separately; do not share a single capacitor between sides. Route A-side and B-side traces on the same layer as the IC to avoid vias on such a fine-pitch pattern.
Open-drain translation performance is dominated by the external pull-up resistors, not the NTSX2102 itself. Estimate rise time as 0.8473 x R_pullup x C_bus (RC to 63%); for a 50 pF bus at Fast-mode Plus (1 Mbit/s), keep the pull-up near 1 kOhm to 1.5 kOhm on the loaded side. Larger pull-ups save current but stretch rise times and limit bus speed. Because the device is rated at 50 Mbit/s, the translator will rarely be the bottleneck for I2C; size pull-ups to the bus, verify with scope measurements on the highest-capacitance configuration.
Two frequent mistakes with this device class: (1) using it with an A-side rail below its minimum - NXP community discussion indicates the A-side operates from about 1.65 V, so a 1.2 V domain will not work; select a lower-voltage translator instead. (2) Mixing push-pull drivers onto open-drain lines - a push-pull high driver on either side will fight the opposite side's pull-down. Ensure every translated line is open-drain or has a series strategy, and hold OE low until both supply rails are valid during power sequencing so partially-powered ports do not clamp the bus.
Информация о соответствии
Compliance data was not present in the retrieved web data. Verify RoHS/REACH status on the official NXP product page at nxp.com/products/NTSX2102 before procurement.
