Texas Instruments

OPA191ID - 36V Low-Power Precision CMOS Op Amp | Texas Instruments

Артикул: OPA191ID ✓ Активен
36 V Vdss 0.14 mA Id 8-pin SOIC Package
MOQ: 1 |

OPA191ID Обзор

The Texas Instruments OPA191ID is a low-power, precision, 36 V e-trim CMOS operational amplifier with rail-to-rail input and output in an 8-pin SOIC package. It combines a 2.5 MHz gain-bandwidth product, 0.14 mA quiescent current, and 0.25 uV/°C typical input-offset drift, making it suitable for precision signal conditioning on higher-voltage industrial and instrumentation rails.

A CMOS precision operational amplifier is an analog building block that amplifies small voltage differences while operating close to its supply rails. The OPA191 belongs to the operational amplifier hierarchy, where precision amplifiers are used to preserve low-level sensor information, minimize offset error, and drive measurement or control stages accurately. Rail-to-rail input and output operation extends the usable common-mode and output range toward the supply limits.

Key characteristics include a maximum 36 V supply, low quiescent current of 0.14 mA, 2.5 MHz gain-bandwidth product, rail-to-rail input and output stages, and e-trim offset adjustment. The 0.25 uV/°C typical input-offset drift helps preserve accuracy as an instrument enclosure changes temperature. Low input bias current also reduces error when the amplifier interfaces with high-impedance sensors.

The OPA191 architecture targets precision rather than high-speed signaling. Its 2.5 MHz bandwidth supports feedback networks and instrumentation signals in the kilohertz range, while the 36 V capability allows operation from higher-voltage industrial supplies without a separate low-voltage translator. The e-trim CMOS design also supports low-power operation when continuous monitoring is more important than wideband performance.

Typical uses include current-loop monitoring, 4-20 mA receiver front ends, precision bridge and sensor amplification, high-voltage measurement buffers, and low-power industrial signal-conditioning modules. The SOIC-8 package makes the device straightforward to place on conventional through-hole and mixed-technology boards.

When designing around the OPA191ID, confirm the input common-mode range at the actual supply voltage and load current. Place the feedback components close to the amplifier pins, keep sensitive input traces away from switching nodes, and account for input-bias-current error when driving very high source impedances.

This page organizes the OPA191ID specifications, application guidance, package details, and available family alternatives into an engineering-focused reference that helps shorten component selection and board-design time.

Аналоги без доработки для OPA191ID — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с OPA191ID (тот же форм-фактор и посадочное место) — отличается по Gain-Bandwidth Product, Product Type, Package, Output Swing, Amplifier Type.

Texas Instruments
Gain-Bandwidth Product: 2 MHz
Package: 8-pin SOIC, 0.154 inch body width, 3.90 mm wide
Output Swing: Rail-to-rail, within 18 mV of the rails
Сравнить с OPA191ID →
Texas Instruments
Gain-Bandwidth Product: 10 MHz
Product Type: Single-channel precision operational amplifier
Output Swing: Rail-to-rail
Сравнить с OPA191ID →
Texas Instruments
Product Type: Single operational amplifier
Сравнить с OPA191ID →
Texas Instruments
Gain-Bandwidth Product: 10 MHz
Output Swing: Rail-to-rail
Amplifier Type: Single operational amplifier
Сравнить с OPA191ID →

OPA192ID

✅ Прямая замена ⚠️ Характеристики не проверены
Texas Instruments
📦 8-pin SOIC
Single-channel precision operational amplifier · 36 V · ±5 µV typical · ±0.2 µV/°C typical · 5.5 nV/√Hz at 1 kHz · 140 dB · ±5 pA · 10 MHz

Уточнить цену

Открыть даташит →

OPA197ID

✅ Прямая замена
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 36 V · Rail-to-rail · Rail-to-rail · ±25 µV typical · ±0.25 µV/°C typical · 10 MHz · 1 channel

Уточнить цену

Открыть даташит →

OPA196ID

✅ Прямая замена ⚠️ Характеристики не проверены
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · Texas Instruments · 36 V · Rail-to-rail input and output · Mux-friendly input · 1 · 8-pin SOIC · Surface mount

Уточнить цену

Открыть даташит →

OPA191ID Максимальные параметры и электрические характеристики

Product Type Precision operational amplifier
Amplifier Count 1 circuit
Maximum Supply Voltage 36 V
Technology e-trim CMOS
Rail-to-Rail Input Yes
Rail-to-Rail Output Yes
Gain-Bandwidth Product 2.5 MHz
Ток покоя 0.14 mA
Input Offset Drift 0.25 uV/°C typical
Корпус 8-pin SOIC
Тип монтажа Surface mount

Конфигурация выводов OPA191ID

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Контакт 1 OUT — Amplifier output
Контакт 2 V- — Negative supply connection
Контакт 3 IN+ — Noninverting input
Контакт 4 IN- — Inverting input
Контакт 5 NC — Not connected
Контакт 6 NC — Not connected
Контакт 7 V+ — Positive supply connection
Контакт 8 NC — Not connected

Типичное применение

OPA191ID подходит для 6 применениеs: 24 V Industrial Sensor Conditioning, 4-20 mA Receiver Front End, Precision Bridge Amplification, High-Voltage Measurement Buffer, Low-Power Environmental Monitoring, Precision Audio and Instrumentation Buffer.

🏭

24 V Industrial Sensor Conditioning

The OPA191ID fits 24 V industrial sensor-conditioning modules because its 36 V maximum supply tolerates the rail while its 0.14 mA quiescent current limits continuous overhead. Place the amplifier near the sensor connector and condition the input before long PCB traces accumulate noise. The 0.25 uV/°C typical input-offset drift is particularly useful when the enclosure temperature changes during a production test. Verify the common-mode range at 24 V and add input protection for surge or overvoltage events.

🌐

4-20 mA Receiver Front End

A 4-20 mA receiver can use the OPA191ID to amplify the voltage produced by a current-sense resistor when the available supply supports the input range. Its low input bias current reduces measurement error with high-value sense resistors, and the 2.5 MHz gain-bandwidth product is more than adequate for the slow industrial current loop. Keep the sense resistor close to the amplifier input and place the feedback resistor directly at the output pin to minimize parasitic pickup.

📊

Precision Bridge Amplification

The OPA191ID is suitable as the amplifier in a resistance bridge or strain-gauge front end where offset drift directly affects the result. The 0.25 uV/°C typical input-offset drift and low bias current preserve accuracy as temperature and source impedance change. Operate it with balanced resistive networks and keep input traces short, guarded, and away from regulators and digital switching nodes. Confirm the bridge excitation voltage against the amplifier input common-mode limits.

⚡

High-Voltage Measurement Buffer

The OPA191ID can buffer divider outputs in high-voltage measurement equipment because its 36 V supply rating accommodates 24 V industrial buses and larger headroom. Rail-to-rail input and output stages help preserve signal range near the usable supply limits. Divider impedance should be low enough that input bias current produces less error than the measurement budget. Verify both common-mode range and output swing, since absolute supply capability does not guarantee full rail-to-rail operation at every load.

🧩

Low-Power Environmental Monitoring

Battery-operated or solar-powered environmental monitors benefit from the OPA191ID because its 0.14 mA typical quiescent current is low for a precision amplifier with a 36 V supply rating. The device can condition slow temperature, humidity, or gas-sensor outputs continuously without dominating the standby budget. Use a regulator with low quiescent current, provide local bypass capacitance, and disable unused analog stages through their own supply domains when possible. The 2.5 MHz bandwidth is more than sufficient for sensor signals below the kilohertz range.

🎧

Precision Audio and Instrumentation Buffer

The OPA191ID can serve as a stable DC buffer in instrumentation and low-frequency audio paths where offset drift matters more than wideband slew performance. Its rail-to-rail input and output operation supports single-supply designs, while the 2.5 MHz gain-bandwidth product provides useful margin for audio-band and measurement signals. Keep the gain at unity or low closed-loop gain where stability matters, and place output-load and feedback components close to the device to reduce parasitic oscillation risk.

What is the OPA191ID?
The OPA191ID is a single, low-power, precision CMOS operational amplifier from Texas Instruments with a maximum 36 V supply. It provides rail-to-rail input and output operation in an 8-pin SOIC package, so it is suitable for precision analog front ends powered from higher-voltage industrial rails. The 2.5 MHz gain-bandwidth product and 0.14 mA quiescent current place it between high-speed amplifiers and ultra-low-power instrumentation amplifiers.
What are the key specifications of OPA191ID that engineers should know?
The most important OPA191ID characteristics are its 36 V maximum supply, 2.5 MHz gain-bandwidth product, 0.14 mA quiescent current, rail-to-rail input and output stages, and 0.25 uV/°C typical input-offset drift. These values make it useful for low-level sensor conditioning where offset drift and limited bias current materially affect measurement accuracy. Its 8-pin SOIC package also supports assembly methods common in industrial and instrumentation equipment.
Where can I download the OPA191ID datasheet PDF?
The official OPA191ID datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/opa191.pdf. The document contains the recommended operating conditions, electrical characteristics, pin configuration, application information, and details for the OPA191, OPA2191, and OPA4191 family. Use the manufacturer document when assigning PCB pins or calculating circuit-level error budgets.
What is the OPA191ID pinout?
The OPA191ID uses the standard single-amplifier 8-pin SOIC arrangement: pin 1 is OUT, pin 2 is V−, pin 3 is IN+, pin 4 is IN−, pin 5 is NC, pin 6 is NC, pin 7 is V+, and pin 8 is NC. Verify the physical pin numbering against the pin-description table in the manufacturer datasheet before routing a board, especially when the SOIC footprint is shared with another amplifier family.
Is OPA191ID suitable for high-voltage signal conditioning?
Yes, the OPA191ID is suitable for high-voltage precision signal conditioning because its maximum supply voltage is 36 V. That rating allows it to operate from 24 V industrial rails without immediately exceeding the device limit. The actual input common-mode range and output-swing limits must still be checked at the selected supply voltage and load because they are narrower than the absolute supply rating.
How much current does the OPA191ID consume?
The OPA191ID has a typical quiescent current of 0.14 mA according to the Texas Instruments family comparison information. Quiescent current describes the supply current drawn with no external load, while total supply current also depends on output load current and operating frequency. Its low quiescent demand makes the device suitable for continuously powered measurement modules where amplifier power can dominate the standby budget.
What is the input-offset drift of the OPA191ID?
The typical input-offset drift of the OPA191ID is 0.25 uV/°C, as stated in the Texas Instruments datasheet example for determining offset-voltage change from 25 °C to 75 °C. This low drift is valuable in temperature-sensitive measurement systems because offset errors accumulate as the internal amplifier and reference move with ambient temperature. Pair it with low bias current and an appropriate output-swing margin for high-impedance sensing.
When should I choose OPA191ID instead of OPA192ID?
Choose the OPA191ID when low power and a 2.5 MHz gain-bandwidth product are the primary priorities. The OPA192ID is the higher-bandwidth option in the same family and is better when a signal must be processed faster. Both use the same 8-pin SOIC package arrangement, so the choice should be based on verified bandwidth, noise, power, and stability requirements rather than package convenience alone.
What is the difference between OPA191ID and OPA197ID?
The OPA191ID and OPA197ID share the same 8-pin SOIC footprint and precision CMOS architecture, but they are optimized for different performance priorities. The OPA191ID emphasizes low quiescent current and a 2.5 MHz gain-bandwidth product, while the OPA197 is positioned as a higher-performance family member. Confirm the full electrical specifications in the manufacturer datasheet before treating either device as a functional substitute.
What is the best drop-in replacement for OPA191ID?
OPA192ID is the closest same-package family alternative because it uses the same 8-pin SOIC pin arrangement and retains the 36 V precision CMOS operating class. It changes the performance target, most notably by providing higher bandwidth than the OPA191ID. Verify stability, output-swing requirements, and noise expectations with your feedback network before accepting it as a drop-in replacement.
Can OPA192ID replace OPA191ID without changing the PCB?
OPA192ID can be used in the same SOIC-8 footprint and follows the same single-amplifier pin arrangement as the OPA191ID. However, electrical compatibility does not guarantee identical performance because the OPA192 provides higher bandwidth than the OPA191. Recheck noise gain, output-swing margin, supply current, and transient response against your signal chain after substituting the part.
What can replace OPA191ID in a precision amplifier design?
The OPA192ID is the leading same-package replacement candidate for the OPA191ID, followed by the OPA197ID and OPA196ID family options where their respective performance characteristics satisfy the design. A valid replacement must preserve the 8-pin SOIC pinout and meet the supply, offset, bias-current, bandwidth, and stability requirements of the circuit. Component substitution is a design decision, not a footprint-only exchange.
Is OPA191ID suitable for a 24 V industrial measurement module?
The OPA191ID is well suited to a 24 V industrial measurement module because its 36 V maximum supply exceeds a 24 V rail and its 0.14 mA quiescent current supports continuous operation. Place a suitably rated protection network ahead of the input pins and verify the common-mode range at the exact supply voltage. Keep high-impedance sensor traces short and away from switching power stages.
Where to buy OPA191ID online?
The OPA191ID can be ordered through the Request a Quote form on this page. The form is the appropriate route for checking current unit availability, order quantities, and lead time for the exact 8-pin SOIC ordering code. Supply the required quantity, target date, and shipment destination so the current commercial response reflects your production plan.
What is the price and lead time of OPA191ID?
Current pricing and production lead time for the OPA191ID are handled through the Request a Quote form on this page. Submit the required order quantity and target delivery date to obtain a current quotation rather than relying on a historical catalog amount. The 8-pin SOIC ordering code shown on this page should be included in the request for an exact quotation.
Is OPA191ID in stock?
Stock status for the OPA191ID changes with inventory and order volume, so use the Request a Quote form on this page to request current availability. Include your required quantity, scheduled build dates, and approved manufacturer-part-number requirements. For scheduled production, confirm that the quoted quantity and delivery window cover your entire assembly plan.

Справочные инженерные данные для OPA191ID — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the OPA191ID when the design needs a precision amplifier with a 36 V supply rating, low quiescent current, rail-to-rail input and output operation, and only moderate bandwidth. It is a strong fit for 24 V industrial sensors, 4-20 mA receivers, bridge measurement front ends, and continuously powered monitoring modules. Select OPA192ID when the same family and footprint are required but signal speed is more important than minimum power. Consider OPA197ID or OPA196ID when their higher-performance electrical characteristics better match the target, but recheck stability, noise, bias current, and output swing. No alternative should be accepted solely because it fits the SOIC-8 footprint; verify the complete operating envelope and confirm that the required precision performance remains within the system error budget.

Сравнение с аналогами

Параметр Этот товар OPA192ID OPA197ID OPA196ID
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Count 1 circuit 1 circuit 1 circuit 1 circuit

Ключевые отличия

  • Lower-bandwidth precision option suited to slow instrumentation signals (против OPA192ID)
  • High-voltage precision capability with low standby current (против OPA197ID)
  • Same-package family alternatives simplify board evaluation (против OPA196ID)

Заметки по проектированию

A 36 V maximum supply rating does not mean that every input may swing to 36 V under all conditions. Check the operating common-mode range at the actual supply voltage, load current, and junction temperature before connecting the input to a high-voltage source. For industrial inputs, place series resistance and appropriately rated clamp protection ahead of pins 3 and 4, and connect the amplifier ground directly to the analog return path.

Route the noninverting and inverting inputs as short, matched traces and place the feedback network close to pins 3, 4, and 1. Keep the amplifier ground connection free of switching-return currents, and place local supply bypass capacitance adjacent to pins 2 and 7. These steps reduce thermally induced offset errors, parasitic feedback, and coupling from adjacent digital or power-converter circuitry.

Estimated quiescent dissipation at a 36 V supply and 0.14 mA quiescent current is 5.04 mW before output-load current is added. This is an arithmetic estimate using the published supply limit and typical quiescent current, not a maximum-power rating. Actual dissipation, junction temperature, and supply-current limits must be evaluated at the real supply voltage, load, and ambient temperature.

The 2.5 MHz gain-bandwidth product is appropriate for slow instrumentation and feedback-control signals, but it does not imply high-speed transient performance. Check the gain-bandwidth product against the closed-loop gain, and add local compensation or isolation when driving capacitive loads. For precision measurements, favor low-noise reference networks and avoid placing resistive dividers directly at high-impedance inputs when bias-current error dominates the budget.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

Compliance declarations were not identified in the retrieved product-page information. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status in the current Texas Instruments product documentation before releasing a regulated design.

Похожие запросы

OPA191ID datasheet OPA191ID datasheet pdf OPA191ID pinout OPA191ID specifications OPA191ID 36V amplifier Texas Instruments OPA191ID OPA191ID SOIC-8 OPA191ID vs OPA192ID OPA191ID equivalent OPA191ID drop-in replacement OPA191ID replacement OPA191ID application circuit OPA191ID price OPA191ID stock OPA191ID precision op amp

Связанные компоненты & термины

Texas Instruments OPA191ID OPA191 OPA192ID OPA197ID OPA196ID precision operational amplifier CMOS operational amplifier e-trim rail-to-rail input rail-to-rail output gain-bandwidth product quiescent current input offset voltage input offset drift input bias current common-mode range 36 V supply 8-pin SOIC SOIC package surface-mount package industrial sensor conditioning 4-20 mA receiver bridge amplification
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ