OPA4137U - Quad 36V 1MHz FET Op Amp | Texas Instruments
Артикул: OPA4137U ✓ АктивенOPA4137U Обзор
A FET-input operational amplifier is an analog signal-conditioning device that uses field-effect-transistor input stages to provide very low input bias current. Within the signal-chain hierarchy, the OPA4137U belongs to the operational amplifier, analog amplifier, and signal-conditioning IC categories. This low-bias architecture is particularly useful when the amplifier must measure weak currents or signals without loading the source appreciably.
The OPA4137 family combines low-cost construction with precision-oriented performance. Its 5 pA input bias current reduces DC error when sensing high-impedance sources, while the 94 dB open-loop gain supports accurate closed-loop amplification. The 1 MHz gain-bandwidth product is suitable for general-purpose instrumentation operating below the amplifier's higher-frequency limits. A low quiescent current of 220 µA per channel also benefits compact and low-power systems.
The quad configuration integrates four FET-input amplifiers into one package, reducing board area compared with four separate single or dual devices. The OPA4137U is supplied in the 14-SOIC package identified by Texas Instruments as suitable for surface-mount assembly. Its monolithic circuit architecture supports consistent operation across the four channels while providing common supply rails for compact analog front ends.
Typical uses include precision current measurement, photodiode and sensor interfaces, laboratory instrumentation, audio signal conditioning, and low-frequency active filters. The very low bias current is especially advantageous for source impedances in the gigaohm range. The 1 MHz bandwidth also permits practical operation in audio-frequency and general signal-conditioning networks when appropriate feedback and stability components are selected.
PCB design should preserve a low-impedance ground return and place compensation, feedback, and input components close to the relevant amplifier pins. Input bias-current error should be evaluated against source impedance, and unused channels should be configured according to the manufacturer datasheet rather than left floating. Supply bypassing should follow the datasheet guidance and place a ceramic capacitor close to the supply pins.
This product page combines the Texas Instruments device description, ordering information, package details, and manufacturer datasheet with practical application guidance. It also distinguishes verified drop-in alternatives from related amplifier families, helping engineers make package, bandwidth, supply-voltage, and precision decisions before committing to a PCB revision.
Аналоги без доработки для OPA4137U — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
OPA4137UA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA4137UAG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA4137UAE4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA4137U/2K5
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
OPA4137U Максимальные параметры и электрические характеристики
| Amplifier Type | Quad J-FET operational amplifier |
| Number of Channels | 4 channels |
| Напряжение питания | 36 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Bias Current | 5 pA |
| Ток покоя | 220 µA per channel |
| Open-Loop Gain | 94 dB |
| Input Stage | J-FET |
| Корпус | 14-SOIC |
| Тип монтажа | Surface mount |
| Product Family | OPA137 MicroAmplifier series |
| Application Category | Instrumentation and precision signal conditioning |
| Статус RoHS | unknown |
| REACH Status | unknown |
Руководство по цоколевке OPA4137U в корпусе 14-soic
Цоколевка для OPA4137U (корпус 14-soic). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для OPA4137U.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
OPA4137U подходит для 6 применениеs: Precision Transimpedance Amplification, High-Impedance Sensor Signal Conditioning, Laboratory Instrumentation Front Ends, Audio and Low-Frequency Active Filtering, Low-Power Portable Measurement Systems, Industrial Control Signal Conditioning.
Precision Transimpedance Amplification
The OPA4137U fits low-frequency photodiode and current-sensor front ends because its J-FET input stage has 5 pA bias current and the quad device provides four channels for shared analog conditioning. With a 1 MHz gain-bandwidth product, each channel can support moderate-bandwidth transimpedance feedback while preserving low DC input-current error. Place the feedback resistor and compensation capacitor close to the amplifier and evaluate stability across the full signal range. The advantage over a conventional bipolar-input amplifier is lower source loading, while the trade-off is that the 1 MHz bandwidth requires careful compensation for highly capacitive sensors.
Рекомендуется
High-Impedance Sensor Signal Conditioning
OPA4137U is appropriate for electrostatic, capacitive, and other high-impedance sensors whose source current must remain small. The 5 pA input bias current limits the DC error generated across a high source impedance, while the 94 dB open-loop gain supports accurate closed-loop gain. Its 1 MHz bandwidth is useful for low-frequency sensor dynamics but does not replace the input filter and guarding practices needed for very high impedance nodes. Short PCB traces, clean guarding, and low-leakage insulation are as important as the amplifier's input-current specification.
Рекомендуется
Laboratory Instrumentation Front Ends
The OPA4137U can implement four precision conditioning channels in laboratory instrumentation, reducing component count while maintaining the low 220 µA per-channel quiescent current. Its 36 V supply is useful for instrumentation interfaces that operate above conventional 5 V or 3.3 V analog rails. The 1 MHz bandwidth covers many low- and mid-frequency measurement channels, and the 94 dB open-loop gain supports stable non-inverting and inverting stages. Use precision feedback resistors, decouple both supply rails locally, and verify input and output headroom at the actual signal extremes.
Рекомендуется
Audio and Low-Frequency Active Filtering
OPA4137U is suitable for four-channel audio or low-frequency active-filter stages where low input bias current and modest bandwidth are more important than slew rate. Its 5 pA input bias helps avoid disturbing high-impedance source networks, and the 1 MHz gain-bandwidth product provides useful closed-loop gain capability through the audio range. The 36 V operating supply can also simplify signal-chain headroom in line-level or higher-amplitude laboratory circuits. Stable filter operation depends on correct feedback topology and component selection, particularly where Q, capacitive loading, or gain approaches the amplifier's usable bandwidth.
Рекомендуется
Low-Power Portable Measurement Systems
OPA4137U supports portable measurement systems that need several precision analog channels without consuming the board area of separate packages. Each channel contributes approximately 220 µA of quiescent current according to the Texas Instruments OPA4137 datasheet, allowing unused channels to be placed in a low-power state when their circuit configuration permits. The 5 pA input bias reduces errors in battery-powered sensor interfaces, and the 1 MHz bandwidth is adequate for many portable measurement signals. Standby behavior and battery life depend on the selected feedback network, output state, and system-level power controls.
Рекомендуется
Industrial Control Signal Conditioning
OPA4137U can condition several low-frequency industrial control or sensor signals when the interface operates within its 36 V supply capability. The J-FET inputs contribute only 5 pA bias current, helping preserve weak sensor signals, while four channels allow consistent amplifier selection across a multi-axis or multi-parameter controller. The 1 MHz bandwidth handles many process-control signals but not high-bandwidth closed-loop control tasks. Industrial designs should also account for common-mode range, output swing, supply-noise coupling, grounding, and protection networks because those considerations can determine precision before amplifier noise and offset do.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для OPA4137U — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Package | 14-SOIC |
| Brand | Texas Instruments |
| Number of Channels | 4 channels |
| Supply Voltage | 36 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Bias Current | 5 pA |
| Quiescent Current | 220 µA per channel |
| Open-Loop Gain | 94 dB |
| Input Stage | J-FET |
| Product Family | OPA137 MicroAmplifier series |
Ключевые отличия
- Very low J-FET input bias current (против General-purpose bipolar-input operational amplifier)
- Four precision channels in one package (против OPA137 single-channel device)
- Moderate bandwidth with low channel quiescent current (против OPA2137 dual-channel device)
Заметки по проектированию
Route each amplifier's feedback components directly between its input and output pins, and keep high-impedance input nodes short to reduce leakage and parasitic capacitance. Use a continuous ground plane where practical, but place analog return paths away from switching-node currents. For the OPA4137U's 5 pA input bias current, even a contaminated PCB surface or long trace can create meaningful DC error when source impedance is very high.
Place the supply-bypass capacitor close to the 14-SOIC power pins and connect it to a low-impedance ground return. The OPA4137U supports operation from a single 36 V supply, but the complete amplifier still requires adequate voltage headroom for its internal circuitry and the selected output stage. Confirm input and output common-mode limits, output swing, and stability from the manufacturer datasheet before operating near a supply rail.
Choose feedback-gain bandwidth relationships with margin below the OPA4137U's 1 MHz gain-bandwidth product, especially when driving capacitive loads. Feedback compensation values are not universal because sensor capacitance and board parasitics alter the effective feedback network. Probe the intended gain configuration for peaking or ringing, and use a small isolation resistor between the amplifier and unusually capacitive loads when stable operation is otherwise difficult.
Do not treat a related order code or amplifier family as an automatic drop-in replacement. The OPA4137U/2K5 is an identified ordering configuration of the same 14-SOIC family, but replacement decisions must still address temperature grade, qualification, and packing. For actual PCB substitution, compare the exact pin table, 36 V supply capability, 1 MHz bandwidth, input-bias current, output swing, and stability requirements.
Информация о соответствии
Compliance declarations are not stated in the cited manufacturer and distributor records. Check the current Texas Instruments product page and applicable material declarations before production release.