S912XEG128J2VAAR - 16-bit 50MHz 128KB Flash MCU | NXP | Automotive
Артикул: S912XEG128J2VAAR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.9 | $14,90 |
| 10 | $13.85 | $138,50 |
| 100 | $12.4 | $1.240,00 |
| 500 | $11.2 | $5.600,00 |
| 1.000 | $10.05 | $10.050,00 |
S912XEG128J2VAAR Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and configurable peripherals such as timers, communication interfaces, and analog blocks. Within the broader electronics taxonomy, an MCU sits under microcontroller -> embedded processor -> semiconductor device. The HCS12X family extends the legacy HC12 architecture by adding a peripheral co-processor (XGATE) that offloads interrupt-driven I/O tasks from the CPU, allowing deterministic real-time responses in CAN and PWM-heavy automotive networks.
Key differentiating specifications include: 50 MHz CPU clock, 128 KB Flash, 50 ns minimum instruction cycle, on-chip LVD/POR/WDT supervision, and an extended (-40°C to +105°C) operating range. The 80-QFP package provides a low-cost plastic leaded footprint compatible with standard SMT assembly lines. The peripheral set targets body and chassis ECUs: up to 59 I/O, multiple CAN nodes (msCAN), and an enhanced capture timer suit the device for distributed in-vehicle networks.
The HCS12X core's two-stage pipeline and BGND/debug background mode are accessible through a single-wire BDM (Background Debug Mode) port, eliminating the need for a costly JTAG emulator during lab bring-up. The internal XGATE coprocessor executes data-movement and peripheral-event service routines in parallel with the CPU, freeing main-line cycles for application logic and effectively doubling throughput on interrupt-bound workloads.
Typical automotive applications include body control modules, instrument cluster slaves, HVAC controllers, and gateway/bridge nodes that aggregate CAN/LIN sub-networks. Industrial variants can be deployed in PLC I/O expanders and small-form-factor motor controllers.
When designing with this device, allocate the XGATE vector table in protected Flash and reserve at least 4 KB of RAM for stack and interrupt context to prevent overflow under heavy CAN traffic. Use the internal regulated 2.5 V core voltage to simplify power-tree design; place a 100 nF decoupling capacitor within 5 mm of every VDD/VSS pin pair.
This page synthesizes distributor stock and pricing, drop-in alternative listings, and engineering design notes that go beyond the manufacturer datasheet to help procurement and firmware teams make informed decisions.
Аналоги без доработки для S912XEG128J2VAAR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с S912XEG128J2VAAR (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Flash Memory, Core Processor, ADC Resolution.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
S912XET512J2VAGR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$1 / шт.
Открыть даташит →S912XEG384J2VAL
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$17.8 / шт.
Открыть даташит →S912XET256J2VAG
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
Уточнить цену
Открыть даташит →S912XEG128J2VAAR-Q1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S12XF384J2MLMR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
Уточнить цену
Открыть даташит →MC9S12XDT512MAA
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
Уточнить цену
Открыть даташит →S912XEG128J2VAAR Максимальные параметры и электрические характеристики
| Core Processor | HCS12X |
| Core Size | 16-Bit |
| Maximum CPU Frequency | 50 MHz |
| Program Memory Size | 128 KB (128K x 8) |
| Program Memory Type | FLASH |
| Корпус | 80-QFP (14x14 mm) |
| Number of I/O | 59 |
| Supply Voltage Range | 1.8 V (typical core) |
| Рабочая температура | -40°C to +105°C |
| Connectivity | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI |
| Peripherals | LVD, POR, PWM, WDT |
| Тип монтажа | Surface Mount |
| Terminal Form | GULL WING |
| Статус RoHS | Compliant |
| Temperature Grade | AUTOMOTIVE / INDUSTRIAL |
| Lead-Free | Yes |
Конфигурация выводов S912XEG128J2VAAR
| Контакт 1 | VDDR — Voltage regulator supply |
| Контакт 2 | VDD — Digital supply voltage |
| Контакт 3 | VSS — Ground |
| Контакт 4 | BKGD — Background Debug Mode pin |
| Контакт 5 | MODC — Mode select / BDM mode |
| Контакт 6 | RESET — External reset input, active low |
| Контакт 7 | XOSC1 — External oscillator input |
| Контакт 8 | XOSC2 — External oscillator output |
| Контакт 9 | TEST — Test mode pin (tie to VSS in application) |
| Контакт 10 | VSS — Ground |
| Контакт 11 | VDD — Digital supply voltage |
| Контакт 12 | PAD0 — Port AD bit 0 / AN0 |
| Контакт 13 | PAD1 — Port AD bit 1 / AN1 |
| Контакт 14 | PAD2 — Port AD bit 2 / AN2 |
| Контакт 15 | PAD3 — Port AD bit 3 / AN3 |
| Контакт 16 | PAD4 — Port AD bit 4 / AN4 |
| Контакт 17 | PAD5 — Port AD bit 5 / AN5 |
| Контакт 18 | PAD6 — Port AD bit 6 / AN6 |
| Контакт 19 | PAD7 — Port AD bit 7 / AN7 |
| Контакт 20 | VSS — Ground |
| Контакт 21 | PAD8 — Port AD bit 8 / AN8 |
| Контакт 22 | PAD9 — Port AD bit 9 / AN9 |
| Контакт 23 | PAD10 — Port AD bit 10 / AN10 |
| Контакт 24 | PAD11 — Port AD bit 11 / AN11 |
| Контакт 25 | PAD12 — Port AD bit 12 / AN12 |
| Контакт 26 | PAD13 — Port AD bit 13 / AN13 |
| Контакт 27 | PAD14 — Port AD bit 14 / AN14 |
| Контакт 28 | PAD15 — Port AD bit 15 / AN15 |
| Контакт 29 | VDDA — Analog supply voltage |
| Контакт 30 | VSSA — Analog ground |
| Контакт 31 | VRH — ADC reference high voltage |
| Контакт 32 | VRL — ADC reference low voltage |
| Контакт 33 | PT0 — Port T bit 0 / IOC0 |
| Контакт 34 | PT1 — Port T bit 1 / IOC1 |
| Контакт 35 | PT2 — Port T bit 2 / IOC2 |
| Контакт 36 | PT3 — Port T bit 3 / IOC3 |
| Контакт 37 | PT4 — Port T bit 4 / IOC4 |
| Контакт 38 | PT5 — Port T bit 5 / IOC5 |
| Контакт 39 | PT6 — Port T bit 6 / IOC6 |
| Контакт 40 | PT7 — Port T bit 7 / IOC7 |
| Контакт 41 | PP0 — Port P bit 0 / PWM0 |
| Контакт 42 | PP1 — Port P bit 1 / PWM1 |
| Контакт 43 | PP2 — Port P bit 2 / PWM2 |
| Контакт 44 | PP3 — Port P bit 3 / PWM3 |
| Контакт 45 | PP4 — Port P bit 4 / PWM4 |
| Контакт 46 | PP5 — Port P bit 5 / PWM5 |
| Контакт 47 | PP6 — Port P bit 6 / PWM6 |
| Контакт 48 | PP7 — Port P bit 7 / PWM7 |
| Контакт 49 | PJ0 — Port J bit 0 / KWJ0 |
| Контакт 50 | PJ1 — Port J bit 1 / KWJ1 |
| Контакт 51 | PJ2 — Port J bit 2 / KWJ2 |
| Контакт 52 | PJ3 — Port J bit 3 / KWJ3 |
| Контакт 53 | PJ4 — Port J bit 4 / KWJ4 |
| Контакт 54 | PJ5 — Port J bit 5 / KWJ5 |
| Контакт 55 | PJ6 — Port J bit 6 / KWJ6 |
| Контакт 56 | PJ7 — Port J bit 7 / KWJ7 |
| Контакт 57 | PM0 — Port M bit 0 / CAN0TX |
| Контакт 58 | PM1 — Port M bit 1 / CAN0RX |
| Контакт 59 | PM2 — Port M bit 2 / SPI0SCK |
| Контакт 60 | PM3 — Port M bit 3 / SPI0MOSI |
| Контакт 61 | PM4 — Port M bit 4 / SPI0MISO |
| Контакт 62 | PM5 — Port M bit 5 / SPI0SS |
| Контакт 63 | PM6 — Port M bit 6 / SCL |
| Контакт 64 | PM7 — Port M bit 7 / SDA |
| Контакт 65 | PS0 — Port S bit 0 / SCI0TXD |
| Контакт 66 | PS1 — Port S bit 1 / SCI0RXD |
| Контакт 67 | PS2 — Port S bit 2 / SCI1TXD |
| Контакт 68 | PS3 — Port S bit 3 / SCI1RXD |
| Контакт 69 | PS4 — Port S bit 4 |
| Контакт 70 | PS5 — Port S bit 5 |
| Контакт 71 | PS6 — Port S bit 6 |
| Контакт 72 | PS7 — Port S bit 7 |
| Контакт 73 | PE0 — Port E bit 0 / XIRQ |
| Контакт 74 | PE1 — Port E bit 1 / IRQ |
| Контакт 75 | PE2 — Port E bit 2 |
| Контакт 76 | PE3 — Port E bit 3 |
| Контакт 77 | PE4 — Port E bit 4 |
| Контакт 78 | PE5 — Port E bit 5 |
| Контакт 79 | PE6 — Port E bit 6 |
| Контакт 80 | PE7 — Port E bit 7 |
Типичное применение
S912XEG128J2VAAR подходит для 6 применениеs: Automotive Body Control Module (BCM), Instrument Cluster Slave Node, HVAC Control Module, CAN Gateway / Bridge Node, Industrial PLC I/O Expander, Small-Form-Factor Motor Controller.
Automotive Body Control Module (BCM)
The S912XEG128J2VAAR is well matched to body control ECUs that aggregate door, lighting, mirror, and wiper functions across a CAN bus. Its 50 MHz HCS12X core and XGATE peripheral co-processor handle CAN message processing and PWM dimming in parallel, keeping CPU headroom available for the BCM application layer. The 59 GPIO pins comfortably serve typical BCM signal counts (door locks, lamp drivers, switch inputs), and the -40°C to +105°C automotive temperature grade meets under-hood and cabin thermal stress. On-chip LVD/POR/WDT supervisors simplify ASIL-rated firmware development and shorten BIST cycles.
Рекомендуется
Instrument Cluster Slave Node
The S912XEG128J2VAAR drives instrument cluster slave nodes that stepper-motor-control gauges and report cluster status over msCAN. Its PWM and enhanced capture timer channels generate the stepper pulse trains needed for analog-style gauges, while the SCI/SPI ports talk to the cluster master and to local LED drivers. At 50 MHz the part runs the gauge-stepper math and CAN interrupt service routines concurrently with XGATE offload, avoiding stepper jitter under heavy bus traffic. The 128 KB Flash holds pointer and warning-icon bitmaps, gauge calibration tables, and the CAN communication stack.
Рекомендуется
HVAC Control Module
Climate-control ECUs rely on the S912XEG128J2VAAR's mix of ADC channels (for temperature and pressure sensors), PWM outputs (for blower speed and mode-door actuators), and CAN connectivity to the body network. The 50 MHz core runs the PID loops that blend cabin and setpoint temperatures every 50 ms without missing a CAN frame. The on-chip WDT and LVD ensure recovery from brown-out events during cranking transients, a known issue in 12 V automotive rails. With 128 KB Flash the part stores the climate state machine, calibration curves, and a small diagnostic trouble-code buffer.
Рекомендуется
CAN Gateway / Bridge Node
Gateway ECUs that route messages between CAN, LIN, and proprietary sub-networks fit the S912XEG128J2VAAR profile. The on-chip msCAN nodes (count to verify per datasheet) plus SCI/SPI peripherals can each terminate a different physical layer, while the HCS12X CPU handles routing tables and message filtering. The XGATE co-processor accelerates the per-message copy/forward routines that would otherwise dominate CPU time on a 50 MHz core. With 128 KB Flash the gateway code, network descriptors, and OEM-specific routing rules fit without external memory.
Рекомендуется
Industrial PLC I/O Expander
Distributed PLC I/O modules use the S912XEG128J2VAAR as a CANOpen or Modbus slave that aggregates 24 V digital inputs and outputs. Its 59 GPIO directly drive optocouplers and relay coils, the PWM channels control proportional valves, and the SPI port drives external digital potentiometers. The 50 MHz CPU handles deterministic I/O scan loops under 1 ms while running the communication stack concurrently via XGATE. Industrial users benefit from the same -40°C to +105°C thermal envelope that NXP validates for automotive, giving long-term reliability in factory-floor cabinets.
Рекомендуется
Small-Form-Factor Motor Controller
Brushless DC (BLDC) and stepper motor controllers fit the S912XEG128J2VAAR in compact 80-QFP housings. The enhanced capture timer and PWM modules generate complementary 3-phase PWM with dead-time insertion, while the ADC reads back-current sensing resistors. The XGATE co-processor services the commutation interrupt and current-sense sampling in parallel with the main CPU, enabling field-oriented control (FOC) loops under 20 µs. The 128 KB Flash stores the FOC algorithm and the application-specific motor parameter table.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для S912XEG128J2VAAR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | S912XET512J2VAGR | S912XEG384J2VAL | S912XET256J2VAG | MC9S12XDT512MAA |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-QFP (14x14 mm) | 80-QFP (14x14 mm) - same | 80-QFP (14x14 mm) - same | 80-QFP (14x14 mm) - same | 80-QFP (14x14 mm) - same |
| Core | HCS12X 16-bit | HCS12X 16-bit | HCS12X 16-bit | HCS12X 16-bit | HCS12X 16-bit |
| Max CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 40 MHz |
| Flash | 128 KB | 512 KB | 384 KB | 256 KB | 512 KB |
| Operating Temperature | -40°C to +105°C | -40°C to +105°C | -40°C to +105°C | -40°C to +105°C | -40°C to +85°C |
| Connectivity | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI | CANbus, EBI/EMI, I²C, IrDA, SCI, SPI |
Ключевые отличия
- Higher CPU clock than S12XD family derivatives (против MC9S12XDT512MAA)
- Lower Flash cost-point than XET variants with same package (против S912XET512J2VAGR)
- Automotive temperature grade over commercial S12XEG128J2CAA (против S912XEG128J2CAA)
Заметки по проектированию
The S912XEG128J2VAAR requires a clean +5 V supply on the VDD pins with a 100 nF ceramic decoupling capacitor placed within 5 mm of every VDD/VSS pair. Bulk capacitance of 4.7 µF to 10 µF should sit at the regulator output. During 12 V automotive cranking transients the on-chip LVD holds the part in reset until the supply stabilizes - place a 22 µF hold-up cap on VDD if your power tree does not already provide this.
Route the XOSC1/XOSC2 traces as a guarded differential pair, keeping them within 5 mm of the MCU and away from switching signals such as PWM or CAN. Place a 4-layer ground pour directly under the 80-QFP footprint and stitch vias around its perimeter to give the VSS pins a low-impedance return path. The exposed thermal pad is not present on this QFP, but a copper pour on top layer still reduces junction temperature by 10-15 °C at full CPU load.
Do not leave the BKGD/MODC pins floating during reset - the MODC pin must be tied to VSS through a 4.7 kΩ resistor for normal operation or to VDD for BDM mode, per the S12XE datasheet. Always configure the XGATE vector table in protected Flash before enabling interrupts, or unexpected jumps will occur. Keep the watchdog timer enabled in production firmware; the on-chip WDT is one of the cheapest safety mechanisms you have.
Series-terminate the CANH/CANL traces with 120 Ω at each node and keep the stub length to the transceiver below 5 cm. For SPI buses running above 5 MHz, place a 33 Ω series resistor at the SCK driver to dampen reflections. The SCI UART pins are 5 V tolerant and can share buses with 3.3 V devices, but verify the high-level input voltage VIH is met when crossing voltage domains.
Информация о соответствии
RoHS and REACH compliance per NXP product page. AEC-Q100 qualified for automotive applications per the -40°C to +105°C temperature grade. Halogen-free status not listed in the verified data - default to 'unknown'.