S9S12H256J1VFVE - 16-bit HCS12 MCU, 256KB Flash, 144-LQFP | NXP
Артикул: S9S12H256J1VFVE ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.4 | $164,00 |
| 100 | $14.2 | $1.420,00 |
| 500 | $12.1 | $6.050,00 |
| 1.000 | $10.5 | $10.500,00 |
S9S12H256J1VFVE Обзор
An automotive-grade microcontroller (MCU) is a microcontroller that has been designed, characterized, and qualified to operate reliably in the harsh electrical and thermal environments of a vehicle. Within the broader product hierarchy, MCUs sit inside the Integrated Circuits category; the S9S12H256J1VFVE specifically belongs to the 16-bit HCS12 sub-family of NXP/Freescale S12 microcontrollers, which are widely deployed in body, chassis, and powertrain electronic control units (ECUs). The HCS12 core is a CISC architecture with full 16-bit data paths, and the part name's suffix 'H256' indicates 256 KB of FLASH, while 'J1VFVE' decodes to LQFP-144 package, automotive grade, tape-and-reel packaging.
Key features include 256 KB FLASH, 12 KB RAM, 4 KB EEPROM, 50 MHz maximum CPU clock, a PLL block for adjustable speed/power trade-offs, multiple timers including a 16-bit Enhanced Capture Timer and an 8-bit Pulse-Width Modulator (PWM) module, an MSCAN (CAN 2.0 A/B) controller, an SPI peripheral, an asynchronous/synchronous SCI serial interface, plus 12 general-purpose I/O pins with interrupt and wake-up capability from STOP or pseudo-STOP modes. The 144-pin LQFP footprint exposes all major buses and analog inputs for body-controller and instrument-cluster applications.
The internal bus matrix is fed by an on-chip PLL that allows the bus clock to be derived from a low-frequency external crystal, reducing electromagnetic emissions and quiescent current. ECC on the FLASH array and a separate EEPROM block allow robust in-field parameter storage, which is required for adaptive automotive software. The HCS12 core executes CISC instructions in 1-5 bus cycles, providing deterministic interrupt latency for real-time control loops.
Typical applications include automotive body controllers, instrument clusters, HVAC control modules, lighting controllers, door/seat modules, and industrial CAN nodes where a 16-bit automotive MCU is required. The part is also used in legacy industrial PLCs and stepper/servo controllers that already have an HCS12 firmware base. The wide -40 °C to +105 °C automotive temperature range and on-chip CAN make it suitable for in-cabin and under-hood controllers.
When designing with this part, provide a 5 V-tolerant decoupling network on each VDD/VSS pair, route the ECLK/XIRQ/IRQ reset chain with short traces, and use the internal PLL with a 4 MHz-16 MHz crystal to derive the 50 MHz bus clock. Always enable the COP watchdog and configure the MSCAN baud rate using a 16 MHz oscillator reference for CAN 2.0B operation at 1 Mbit/s.
This page synthesizes NXP/Freescale distributor pricing, drop-in LQFP-144 alternatives from the S9S12H and S12X families, automotive-grade compliance notes, and practical design guidance that go beyond the manufacturer datasheet.
Аналоги без доработки для S9S12H256J1VFVE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с S9S12H256J1VFVE (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Automotive Qualification, Product Type, Mounting Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
S9S12H256J2VFVER
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →MC9S12H256VFVE
✅ Прямая замена✓ В наличии
$10.95 / шт.
Открыть даташит →MC9S12H256VFVER
✅ Прямая замена✓ В наличии
$10.95 / шт.
Открыть даташит →S9S12HZ256J3VAL
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MC9S12XHZ256VAG
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$15.2 / шт.
Открыть даташит →S9S12H256J1VFVE Максимальные параметры и электрические характеристики
| CPU Core | HCS12 (16-bit CISC) |
| Program Memory (FLASH) | 256 KB |
| Data RAM | 12 KB |
| Data EEPROM | 4 KB |
| Maximum CPU Clock | 50 MHz |
| Typical Operating Speed | 25 MHz |
| Корпус | 144-pin LQFP (20 x 20 mm) |
| Рабочая температура | -40 °C to +105 °C (automotive) |
| CAN Interface | MSCAN (CAN 2.0A/B), 1 channel |
| Serial Interfaces | SCI (UART), SPI, I2C-capable |
| Timers | Enhanced Capture Timer (ECT), 8-bit PWM, 16-bit Timer |
| ADC | 10-bit, 8/16-channel ATD |
| GPIO | Up to 91 I/O pins (12 with wake-up from STOP) |
| PLL | On-chip, configurable from 4-16 MHz reference |
| Watchdog | COP watchdog timer |
| Напряжение питания | 5.0 V typical (4.5 V - 5.5 V) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| Automotive Qualification | AEC-Q100 qualified |
| Lead-Free | Yes |
Руководство по цоколевке S9S12H256J1VFVE в корпусе 144-pin lqfp (20 x 20 mm)
Цоколевка для S9S12H256J1VFVE (корпус 144-pin lqfp (20 x 20 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для S9S12H256J1VFVE.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
S9S12H256J1VFVE подходит для 6 применениеs: Automotive Body Controller, Instrument Cluster Display Controller, HVAC Control Module, Lighting Control Module (BCM), Door Module / Seat Module, Industrial CAN Node / PLC Slice.
Automotive Body Controller
The S9S12H256J1VFVE's 256 KB FLASH and 50 MHz HCS12 core make it well suited to automotive body controllers that orchestrate central locking, exterior lighting, wiper control, and accessory switching. Its on-chip MSCAN 2.0B controller integrates the in-vehicle network gateway with up to 1 Mbit/s baud rate, eliminating an external CAN transceiver companion. AEC-Q100 Grade-1 qualification and -40 °C to +105 °C operation cover in-cabin and most under-hood body modules. Compared with newer S12X parts the S9S12H256J1VFVE offers lower power consumption at idle and a smaller code footprint due to its CISC efficiency.
Рекомендуется
Instrument Cluster Display Controller
The S9S12H256J1VFVE can drive stepper-motor-driven analog gauges and segment-LCD or LED displays through its PWM channels and Enhanced Capture Timer, freeing the host CPU from interrupt-driven gauge updates. 12 KB of on-chip RAM holds the dial-position lookup tables and 4 KB EEPROM stores odometer and trip data with automotive-grade endurance. The 144-LQFP package exposes the full bus for connection to companion LED driver and stepper driver ICs. Compared with software-only loop implementations, using the dedicated PWM and ECT peripherals reduces CPU load below 20 % at refresh rate.
Рекомендуется
HVAC Control Module
HVAC modules require deterministic real-time control of blower speed, blend/air-mode doors, and temperature sensors - exactly the workload the S9S12H256J1VFVE's HCS12 core plus ECT, PWM, and 10-bit ADC target. The 12-bit-equivalent noise performance of the on-chip ATD combined with 256 KB FLASH supports PID control loops for cabin-temperature regulation. AEC-Q100 Grade-1 compliance and 50 MHz headroom allow simultaneous LIN/CAN network stacks plus sensor fusion. Compared with lower-end S08 parts, the HCS12 16-bit data path eliminates byte/word juggling for PID math.
Рекомендуется
Lighting Control Module (BCM)
Body lighting modules running adaptive headlamp logic and turn-signal sequencing benefit from the S9S12H256J1VFVE's multiple PWM outputs (eight 8-bit channels) and ECT for fade-in/fade-out timing. 256 KB FLASH accommodates full DRL/AFS lookup tables while 4 KB EEPROM stores driver preferences and bulb-life counters. MSCAN connectivity lets the module join the vehicle CAN network for central BCM commands. Compared with discrete logic implementations, this single-chip solution cuts PCB area by 60 % while supporting OTA-friendly firmware upgrades.
Рекомендуется
Door Module / Seat Module
Door and seat modules require simultaneous control of window lift, mirror adjust, seat position memory, and child-safety disable logic. The S9S12H256J1VFVE's 12 KB RAM plus 4 KB EEPROM retains seat-memory positions through battery disconnect, while its MSCAN interface talks to the central BCM. The 144-LQFP package allows direct PCB integration next to the H-bridge driver ICs, eliminating wiring-harness cost. Compared with 8-bit S08 implementations, the 16-bit HCS12 path lets one MCU replace two S08 slaves, halving module cost.
Рекомендуется
Industrial CAN Node / PLC Slice
Outside automotive, the S9S12H256J1VFVE is a strong fit for industrial CAN nodes, PLC slice I/O, and motor-control edge controllers that need a 16-bit deterministic core. The on-chip MSCAN 2.0B plus CANopen library support reduces external component count, while 256 KB FLASH stores CANopen stack plus application logic. -40 °C to +105 °C operation covers industrial cabinets and outdoor enclosures. Compared with 32-bit ARM Cortex-M0 alternatives, the HCS12 CISC core delivers faster interrupt response with deterministic cycle counts.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для S9S12H256J1VFVE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | S9S12H256J2VFVER | MC9S12H256VFVE | MC9S12H256VFVER | S9S12HZ256J3VAL | MC9S12XHZ256VAG |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors (Freescale legacy) | NXP Semiconductors | NXP Semiconductors (Freescale legacy) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 144-LQFP (20x20 mm) | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same | 144-LQFP (20x20 mm) - same |
| CPU Core | HCS12 (CISC 16-bit) | HCS12 - identical | HCS12 - identical | HCS12 - identical | HCS12 - identical | S12X (with XGATE coprocessor) |
| Maximum Clock | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 40 MHz |
| FLASH Memory | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| RAM | 12 KB | 12 KB | 12 KB | 12 KB | 12 KB | 12 KB |
| Operating Temperature | -40 °C to +105 °C (AEC-Q100 Grade-1) | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +125 °C (Grade-0) | -40 °C to +105 °C |
| Lifecycle Status | NRND | NRND | Active (Freescale legacy inventory) | Active | NRND | Active |
Ключевые отличия
- AEC-Q100 Grade-1 qualified with 50 MHz HCS12 in a 144-LQFP for body controllers (против MC9S12H256VFVE)
- On-chip MSCAN 2.0B controller plus 256 KB FLASH in 144-LQFP (против MC9S12XHZ256VAG)
- Grade-1 (-40 °C to +105 °C) automotive qualification (против S9S12HZ256J3VAL)
Заметки по проектированию
The S9S12H256J1VFVE is a 5 V part with separate VDD/VSS pins for the PLL, ADC, and I/O segments. Decouple each VDD/VSS pair with a 100 nF X7R ceramic plus a 10 µF bulk tantalum on the regulator output, and place the 100 nF caps within 3 mm of the corresponding pin. Configure the internal voltage regulator (VREG) for normal full-performance mode by tying the VREGEN pin to VDDX; otherwise the part drops to reduced-current pseudo-STOP after reset.
Do not assume the S9S12H256J1VFVE auto-configures the PLL on reset. The CLKSEL, PLLSEL, and PLLCR register values must be programmed early in the startup code, otherwise the bus runs at the slow oscillator reference and software timing will be off by an order of magnitude. Also enable the COP watchdog in CR2 - leaving it disabled is a common failure root cause during EMC and brown-out testing.
Route the ECLK output to a guard trace with ground on both sides to minimise radiated emissions; this MCU is known to cause CISPR 25 Class 5 compliance failures if ECLK is left un-terminated. Keep the analog ATD inputs short and away from PWM outputs; route a dedicated AGND island under the part back to a star ground at the 5 V LDO return. The 144-LQFP thermal pad is not internally bonded - it must be soldered to the copper pour for mechanical robustness even though it carries no electrical connection.
For MSCAN 2.0B at 1 Mbit/s the bus-clock must be 8 MHz or higher to keep the CAN bit-timing granularity under 1 %. Use a 4 MHz or 16 MHz crystal rather than a ceramic resonator to hold bit-time jitter below 0.5 %. When the part is powered through long automotive cable harness, add an external TVS such as NXP PESD1CAN on the CANH/CANL pins to meet IEC 61000-4-2 ESD.
Информация о соответствии
AEC-Q100 Grade-1 qualified per NXP product family page. RoHS/REACH compliance confirmed by NXP ordering code suffix VFVE (lead-free matte-tin finish).