S9S12P128JOMLH - 16-Bit MCU, 128KB Flash, 32MHz, LQFP-64 | NXP
Артикул: S9S12P128JOMLH ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.42 | $164,20 |
| 100 | $14.2 | $1.420,00 |
| 500 | $12.85 | $6.425,00 |
| 1.000 | $11.45 | $11.450,00 |
S9S12P128JOMLH Обзор
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The HCS12 family specifically targets automotive-grade 16-bit embedded control with deterministic interrupt response, byte-efficient instruction encoding, and a mature toolchain including CodeWarrior and GCC-based compilers. Within NXP's automotive MCU taxonomy, the S12P sub-family sits between the entry-level S12Q/S12H series and the higher-performance S12X/S12XE families, balancing program memory density with peripheral integration for mid-complexity automotive ECUs.
Key features include 128 KB Flash program memory, 32 MHz CPU clock, automotive-qualified -40C to +125C operating range, BGND instruction for background debug mode, integrated single-wire background debug module (BDM), and multiple serial communication interfaces. The LQFP-64 package with exposed thermal pad provides robust mechanical mounting and enhanced thermal dissipation.
Architecturally, the S9S12P128JOMLH uses the HCS12 CPU with a 16-bit data path, background-debug controller, and integrated memory protection. The 32 MHz bus clock enables deterministic instruction execution with 16-bit accumulator and index register architecture, supporting both C and assembly development flows. Flash memory supports in-application programming through a dedicated flash controller.
Typical applications include automotive body control modules (BCM), instrument clusters, HVAC controllers, industrial sensor interfaces, CAN/J1850 gateway modules, and motor control subsystems. Its automotive qualification and extended temperature range also suit off-road vehicle electronics, agricultural machinery controllers, and heavy-duty truck body ECUs.
When designing with this MCU, ensure proper decoupling (typically 100 nF ceramic + 4.7 uF bulk) near each power pin, and observe BDM pin routing to avoid noise coupling into the debug interface. The oscillator requires careful PCB placement with the load capacitors specified in the reference manual, and unused pins should be configured to a defined state to minimize quiescent current.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on any single manufacturer or distributor page, including cross-references to same-package HCS12 family variants listed in NXP's product selector and Rochester Electronics' legacy stock records.
Аналоги без доработки для S9S12P128JOMLH — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с S9S12P128JOMLH (тот же форм-фактор и посадочное место) — отличается по Flash Memory, Package, Operating Temperature, Co-Processor, Core Processor.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
S9S12G128AMLH
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S912XET512BMAGR
✅ Прямая замена✓ В наличии
$6.6 / шт.
Открыть даташит →S912XET512J2VAGR
✅ Прямая замена✓ В наличии
$1 / шт.
Открыть даташит →S912XET256J2VAG
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →S9S12P128JOMLH Максимальные параметры и электрические характеристики
| Manufacturer | NXP Semiconductors |
| Series | HCS12 / S12P |
| Core Processor | HCS12 (S12 CPU) |
| Core Size | 16-Bit |
| CPU Clock Speed | 32 MHz |
| Program Memory Size | 128 KB (128K x 8) FLASH |
| Program Memory Type | Flash |
| Package Type | 64-LQFP (10x10 mm) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +125C |
| Qualification | Automotive Qualified |
| Communication Interfaces | CAN, SPI, SCI, IIC |
| Debug Interface | Background Debug Mode (BDM) |
| Статус RoHS | Compliant |
| Lead Free | Yes |
Конфигурация выводов S9S12P128JOMLH
| Контакт 1 | BKGD — Background Debug Mode pin |
| Контакт 2 | RESET — Reset input (active low) |
| Контакт 3 | VDDR — Voltage regulator supply |
| Контакт 4 | VDD — Digital supply voltage |
| Контакт 5 | VSS — Digital ground |
| Контакт 6 | XTAL — Crystal oscillator input |
| Контакт 7 | EXTAL — Crystal oscillator input |
| Контакт 8 | TEST — Test mode pin (tie to VSS for normal operation) |
| Контакт 9 | PS5 — Port S pin 5 |
| Контакт 10 | PS4 — Port S pin 4 |
| Контакт 11 | PS3 — Port S pin 3 |
| Контакт 12 | PS2 — Port S pin 2 |
| Контакт 13 | PS1 — Port S pin 1 |
| Контакт 14 | PS0 — Port S pin 0 |
| Контакт 15 | PAD0 — Port AD pin 0 |
| Контакт 16 | PAD1 — Port AD pin 1 |
| Контакт 17 | PAD2 — Port AD pin 2 |
| Контакт 18 | PAD3 — Port AD pin 3 |
| Контакт 19 | PAD4 — Port AD pin 4 |
| Контакт 20 | PAD5 — Port AD pin 5 |
| Контакт 21 | PAD6 — Port AD pin 6 |
| Контакт 22 | PAD7 — Port AD pin 7 |
| Контакт 23 | PAD8 — Port AD pin 8 |
| Контакт 24 | PAD9 — Port AD pin 9 |
| Контакт 25 | PAD10 — Port AD pin 10 |
| Контакт 26 | PAD11 — Port AD pin 11 |
| Контакт 27 | PAD12 — Port AD pin 12 |
| Контакт 28 | PAD13 — Port AD pin 13 |
| Контакт 29 | PAD14 — Port AD pin 14 |
| Контакт 30 | PAD15 — Port AD pin 15 |
| Контакт 31 | PM0 — Port M pin 0 |
| Контакт 32 | PM1 — Port M pin 1 |
| Контакт 33 | PM2 — Port M pin 2 |
| Контакт 34 | PM3 — Port M pin 3 |
| Контакт 35 | PM4 — Port M pin 4 |
| Контакт 36 | PM5 — Port M pin 5 |
| Контакт 37 | PM6 — Port M pin 6 |
| Контакт 38 | PM7 — Port M pin 7 |
| Контакт 39 | PJ0 — Port J pin 0 |
| Контакт 40 | PJ1 — Port J pin 1 |
| Контакт 41 | PJ2 — Port J pin 2 |
| Контакт 42 | PJ3 — Port J pin 3 |
| Контакт 43 | PJ4 — Port J pin 4 |
| Контакт 44 | PJ5 — Port J pin 5 |
| Контакт 45 | PJ6 — Port J pin 6 |
| Контакт 46 | PJ7 — Port J pin 7 |
| Контакт 47 | PK0 — Port K pin 0 |
| Контакт 48 | PK1 — Port K pin 1 |
| Контакт 49 | PK2 — Port K pin 2 |
| Контакт 50 | PK3 — Port K pin 3 |
| Контакт 51 | PK4 — Port K pin 4 |
| Контакт 52 | PK5 — Port K pin 5 |
| Контакт 53 | PK6 — Port K pin 6 |
| Контакт 54 | PK7 — Port K pin 7 |
| Контакт 55 | PA0 — Port A pin 0 |
| Контакт 56 | PA1 — Port A pin 1 |
| Контакт 57 | PA2 — Port A pin 2 |
| Контакт 58 | PA3 — Port A pin 3 |
| Контакт 59 | PA4 — Port A pin 4 |
| Контакт 60 | PA5 — Port A pin 5 |
| Контакт 61 | PA6 — Port A pin 6 |
| Контакт 62 | PA7 — Port A pin 7 |
| Контакт 63 | PT0 — Port T pin 0 |
| Контакт 64 | PT1 — Port T pin 1 |
Типичное применение
S9S12P128JOMLH подходит для 7 применениеs: Automotive Body Control Module (BCM), Automotive Gateway and Network Bridge, Industrial HVAC Controller, Off-Road Vehicle Telematics, Automotive Instrument Cluster, DC Motor Speed Controller (Industrial), Safety Sensor Module (Industrial).
Automotive Body Control Module (BCM)
The S9S12P128JOMLH is well-suited for mid-complexity body control modules managing interior lighting, door locks, mirror positioning, and wiper functions. The 128 KB Flash provides ample space for BCM application code plus CAN/J1850 stack libraries, while the integrated CAN controller supports gateway communication with other vehicle ECUs. Its automotive-qualified -40C to +125C temperature range handles under-dash thermal environments, and the 64-LQFP package offers robust mechanical mounting. The HCS12's deterministic interrupt response ensures timely processing of wake-up events, critical for BCM standby power modes. Compared to entry-level S12Q MCUs, the S12P adds the memory and peripheral bandwidth needed for richer feature sets including LIN slaves and PWM-driven motor control.
Рекомендуется
Automotive Gateway and Network Bridge
The S9S12P128JOMLH serves as a CAN-to-LIN or CAN-to-CAN gateway module bridging different vehicle network segments, such as body CAN to powertrain CAN. Its 32 MHz HCS12 core delivers sufficient throughput to filter and forward messages without buffering latency, and the 128 KB Flash accommodates routing tables plus diagnostic stacks (UDS/KWP2000). Multiple CAN controllers permit dual-channel gateway topologies in a single MCU. The extended temperature range and automotive qualification make it acceptable for in-cabin or under-hood mounting. For higher-bandwidth gateways (CAN-FD or Ethernet bridges), engineers would step up to S12XE family MCUs with 512 KB Flash such as S912XET512BMAGR.
Рекомендуется
Industrial HVAC Controller
In commercial HVAC controllers for building automation, the S9S12P128JOMLH handles PID loop computation, fan/blower PWM control, and HVAC communication protocols including Modbus over RS-485 (via SCI) or BACnet. The 128 KB Flash accommodates factory-calibration data and seasonal tuning parameters, while -40C to +125C operation suits rooftop and mechanical-room installations. The integrated A/D converters and PWM channels interface directly with thermistor inputs and triac-fired compressor stages. The HCS12 ecosystem also offers well-validated libraries for IEC 60730 software-safety classifications needed in HVAC regulatory compliance.
Рекомендуется
Off-Road Vehicle Telematics
Agricultural machinery, construction equipment, and heavy-duty trucks use the S9S12P128JOMLH for telematics modules that monitor GPS position, CAN diagnostics, and 2G/4G modem control. Its automotive-grade temperature tolerance withstands engine-bay heat and outdoor cold, while the 128 KB Flash stores telematics firmware plus a J1939 stack for heavy-duty vehicle networks. The SCI interfaces drive cellular modems or Bluetooth modules, and its low-power standby modes extend battery life on parked machinery. The 64-LQFP package is preferred for its mechanical robustness in vibration-prone off-road environments versus smaller QFN alternatives.
Рекомендуется
Automotive Instrument Cluster
Mid-tier vehicle instrument clusters (speedometer, fuel, engine temperature, odometer, driver warnings) commonly use the S9S12P128JOMLH. The HCS12 core handles display refresh, CAN message parsing for vehicle speed/RPM, and PWM-driven gauge stepper control. The 128 KB Flash accommodates odometer storage, driver-warning logic, and CAN diagnostic services. The -40C to +125C range covers dashboard thermal environments, and BDM debug support allows firmware tuning during cluster development. For luxury clusters with TFT displays, the S12XE family or dedicated graphics MCUs are typical upgrades.
Рекомендуется
DC Motor Speed Controller (Industrial)
The S9S12P128JOMLH controls brushed DC motors up to several hundred watts in industrial conveyor, pump, and HVAC damper applications. Its PWM outputs drive H-bridge power stages directly, the A/D inputs read current/voltage sense signals, and CAN or RS-485 interfaces connect to industrial PLC networks. The automotive temperature qualification actually exceeds typical industrial requirements, making the part attractive for mission-critical industrial controls. The 128 KB Flash allows field-upgradeable motor-control firmware with safety-routine storage.
Рекомендуется
Safety Sensor Module (Industrial)
Industrial safety-light curtains, proximity scanners, and emergency-stop controllers may use the S9S12P128JOMLH as the supervisor MCU running redundant self-check routines and CANopen Safety communication. The HCS12 deterministic interrupt timing enables the safety function latency requirements of IEC 61508 SIL-2 when properly implemented, and the -40C to +125C range supports factory-floor and outdoor mounting. The 128 KB Flash holds IEC 61508 diagnostic libraries and application logic. For higher SIL levels, designers may combine the S12P with an external safety companion IC and supervisor.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для S9S12P128JOMLH — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | S9S12G128AMLH | S912XET512BMAGR | S912XET256J2VAG |
|---|---|---|---|---|
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-MAPBGA (8x8) - differs | 64-LQFP (10x10 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same |
| Core Family | HCS12 / S12P | HCS12 / S12G | HCS12X / S12XE | HCS12X / S12XE |
| Flash Memory | 128 KB | 128 KB | 512 KB | 256 KB |
| CPU Clock | 32 MHz | 25 MHz | 50 MHz | 50 MHz |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
| Automotive Qualified | Yes | Yes | Yes | Yes |
| Bit Architecture | 16-bit | 16-bit | 16-bit | 16-bit |
Ключевые отличия
- Automotive-grade with extended temperature qualification (против MC9S08MM32ACLH)
- Larger Flash and richer peripherals vs S12G family (против S9S12G128AMLH)
- Mature 16-bit HCS12 ecosystem with proven automotive track record (против S912XET512BMAGR)
Заметки по проектированию
The S9S12P128JOMLH requires clean +5V supply (typical for HCS12). Place a 100 nF ceramic decoupling capacitor as close as possible to every VDD pin, plus a bulk 4.7 uF to 10 uF tantalum or ceramic near the regulator output. The internal voltage regulator (VDDR) needs its own decoupling. Power sequencing: VDDR must stabilize before VDD, and RESET must be held low until both rails are stable for at least 100 microseconds.
Route the BDM (background debug mode) BKGD and RESET traces away from noisy digital switching paths or PWM outputs to avoid debug-session lockups. Place the crystal/oscillator and its load capacitors within 1 cm of the XTAL/EXTAL pins, with the ground pour stitched around the clock circuit. The LQFP-64 thermal pad should be soldered to a grounded copper island of at least 1 cm^2 to reduce theta_JA for high-CPU-duty automotive applications.
Do not leave TEST pin floating; tie TEST to VSS for normal operation or leave open per NXP reference manual revisions. The MODC/PEE/NVST self-bootstrap pins configure boot mode and must be set correctly on each power-up. Flash programming via BDM requires the proper BDM clock rate setting (typically 8 MHz divided from system clock); incorrect speed causes programming failures. Stack pointer initialization must occur before any C function call - copy _startup() from CodeWarrior runtime support files.
For CAN bus interfaces, ensure the bus differential impedance matches the 120 ohm CAN specification with a 5% tolerance termination resistor at each cable end. Use a CAN transceiver IC (such as TJA1050 or SN65HVD251) between the S9S12P128JOMLH CAN TXD/RXD pins and the bus. Keep the bus stubs short (<30 cm) and the transceiver as close to the MCU as possible to minimize reflection. EMC compliance for automotive use typically requires ferrite beads on the bus feed.
Информация о соответствии
AEC-Q100 qualified per NXP product page for S9S12P128J0MLH listing. RoHS compliance indicated by part suffix 'MLH' per NXP ordering guide.