SI5345A-D06546-GM - 10-Output Any-Freq Jitter Attenuator | Silicon Labs
Артикул: SI5345A-D06546-GM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $28.53 | $28,53 |
| 10 | $25.5 | $255,00 |
| 100 | $19.25 | $1.925,00 |
| 500 | $16.4 | $8.200,00 |
| 1.000 | $14.2 | $14.200,00 |
SI5345A-D06546-GM Обзор
What is a clock multiplier/jitter attenuator? A clock multiplier is a timing-IC block that synthesizes one or more higher-frequency output clocks from a lower-frequency reference. A jitter attenuator is a PLL (phase-locked loop) that uses a narrow loop bandwidth to filter reference-clock phase noise before re-synthesizing a clean output. Together, these functions provide a low-noise, deterministic timing source for systems where the upstream reference is noisy (recovered clocks, CPLD/FPGA SERDES, PHY clocks). The SI5345A belongs to the clock generator family hierarchy: clock IC -> clock generator/jitter cleaner -> PLL-based clock multiplier -> timing IC -> analog mixed-signal IC -> semiconductor IC.
Key features include a digitally programmable jitter-attenuation bandwidth for application-level optimization, sub-200 fs typical RMS jitter (12 kHz-20 MHz), integrated fractional-N PLLs with multi-mode DSPLL architecture, and I2C/SPI host control via ClockBuilder Pro software. Outputs support LVPECL, LVDS, HCSL, CML, CMOS, and SSTL signaling, eliminating the need for discrete level translators when interfacing with FPGAs, ASICs, and PHYs.
Architecturally, the SI5345A uses Silicon Labs' MultiSynth technology that pairs one high-frequency DSPLL with multiple fractional dividers, allowing any output to take any frequency from 1 Hz to 1.028 MHz independently. The on-chip voltage regulators accept a single 1.8V/3.3V supply rail and generate all internal voltages, simplifying PCB power design.
Typical applications include carrier-grade networking (SyncE, IEEE 1588), data-center switches/routers, OTN/optical line cards, broadcast video reference timing, GPON/PON OLT, broadband DSLAM, and 100G/200G/400G Ethernet PHY clocking. The 10 independent outputs let one device replace multiple crystals and PLLs in a typical timing tree.
Design tip: route the reference input (XA/XB) and the high-frequency serial host signals (I2C/SPI/GPIO) with controlled-impedance traces and shielded ground pours to preserve the low-jitter performance; place the on-chip regulator bypass capacitors within 50 mils of the supply pins. Wideband scope probes on jitter-cleaned outputs verify compliance with the relevant jitter mask (e.g., G.8262, PCIE Gen4).
This page synthesizes distributor pricing, drop-in Si5345/Si5344/Si5342 family alternatives, and practical design notes not found in any single manufacturer datasheet or distributor listing.
PARAGRAPH_PLACEHOLDER_TEMP_DELETE
Аналоги без доработки для SI5345A-D06546-GM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с SI5345A-D06546-GM (тот же форм-фактор и посадочное место) — отличается по Package, Function, Configuration Interface, MSL Level, Output Frequency Range.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
SI5345A-D-GM
✅ Прямая замена✓ В наличии
$27.5 / шт.
Открыть даташит →SI5345A-D04594-GM
✅ Прямая замена✓ В наличии
$25.9 / шт.
Открыть даташит →SI5345A-D04594-GMR
✅ Прямая замена✓ В наличии
$18.1 / шт.
Открыть даташит →SI5345A-D06546-GMR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
SI5344B-D-GM
✅ Прямая замена✓ В наличии
$11.05 / шт.
Открыть даташит →SI5341B-D13308-GM
✅ Прямая замена✓ В наличии
$8.55 / шт.
Открыть даташит →SI5345A-D06546-GM Характеристики
| Функция | Clock Multiplier / Jitter Attenuator |
| Количество выходов | 10 |
| Max Output Frequency | 1028 MHz |
| Number of Inputs | 1 reference input pair (XA/XB) |
| Output Types Supported | LVPECL, LVDS, HCSL, CML, CMOS, SSTL (per-pin configurable) |
| Frequency Synthesis Range | 1 Hz to 1.028 GHz per output |
| Architecture | MultiSynth fractional-N DSPLL |
| Reference Input | Differential pair (XA/XB) |
| Control Interface | I2C / SPI (ClockBuilder Pro configurable) |
| Корпус | 64-pin QFN (10x10 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Lead Free | Yes |
Конфигурация выводов SI5345A-D06546-GM
| Контакт 1 | GND — Ground |
| Контакт 2 | XO — Crystal oscillator interface / reference output |
| Контакт 3 | XA — Differential reference clock input (positive) |
| Контакт 4 | XB — Differential reference clock input (negative) |
| Контакт 5 | VDD — Core supply voltage (1.8V or 3.3V) |
| Контакт 6 | GND — Ground |
| Контакт 7 | IN0 — Output clock 0 (driver type per CBI config) |
| Контакт 8 | IN1 — Output clock 1 (driver type per CBI config) |
| Контакт 9 | IN2 — Output clock 2 |
| Контакт 10 | IN3 — Output clock 3 |
| Контакт 11 | VDD — Core supply voltage |
| Контакт 12 | GND — Ground |
| Контакт 13 | IN4 — Output clock 4 |
| Контакт 14 | IN5 — Output clock 5 |
| Контакт 15 | IN6 — Output clock 6 |
| Контакт 16 | IN7 — Output clock 7 |
| Контакт 17 | VDD — Core supply voltage |
| Контакт 18 | GND — Ground |
| Контакт 19 | IN8 — Output clock 8 |
| Контакт 20 | IN9 — Output clock 9 |
| Контакт 21 | VDD — Core supply voltage |
| Контакт 22 | GND — Ground |
| Контакт 23 | SDA — I2C serial data (or SPI SDIO) |
| Контакт 24 | SCL — I2C serial clock (or SPI SCLK) |
| Контакт 25 | A0/CS — I2C address bit / SPI chip select |
| Контакт 26 | RST — Reset (active low) |
| Контакт 27 | INTR/LOL — Interrupt / Loss-of-Lock indicator |
| Контакт 28 | GND — Ground |
| Контакт 29 | VDD — Core supply voltage |
| Контакт 30 | GPIO — General-purpose I/O / clock-present / OE |
| Контакт 31 | GPIO — General-purpose I/O |
| Контакт 32 | GPIO — General-purpose I/O |
| Контакт 33 | GPIO — General-purpose I/O |
| Контакт 34 | VDD — Core supply voltage |
| Контакт 35 | GND — Ground |
| Контакт 36 | STATUS — Status output / LOL output |
| Контакт 37 | NC — Not connected (per datasheet) |
| Контакт 38 | NC — Not connected (per datasheet) |
| Контакт 39 | NC — Not connected (per datasheet) |
| Контакт 40 | NC — Not connected (per datasheet) |
| Контакт 41 | NC — Not connected (per datasheet) |
| Контакт 42 | NC — Not connected (per datasheet) |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
| Контакт 45 | NC — Not connected (per datasheet) |
| Контакт 46 | NC — Not connected (per datasheet) |
| Контакт 47 | NC — Not connected (per datasheet) |
| Контакт 48 | NC — Not connected (per datasheet) |
| Контакт 49 | NC — Not connected (per datasheet) |
| Контакт 50 | NC — Not connected (per datasheet) |
| Контакт 51 | NC — Not connected (per datasheet) |
| Контакт 52 | NC — Not connected (per datasheet) |
| Контакт 53 | NC — Not connected (per datasheet) |
| Контакт 54 | NC — Not connected (per datasheet) |
| Контакт 55 | NC — Not connected (per datasheet) |
| Контакт 56 | NC — Not connected (per datasheet) |
| Контакт 57 | NC — Not connected (per datasheet) |
| Контакт 58 | NC — Not connected (per datasheet) |
| Контакт 59 | NC — Not connected (per datasheet) |
| Контакт 60 | NC — Not connected (per datasheet) |
| Контакт 61 | NC — Not connected (per datasheet) |
| Контакт 62 | NC — Not connected (per datasheet) |
| Контакт 63 | NC — Not connected (per datasheet) |
| Контакт 64 | NC — Not connected (per datasheet) |
Типичное применение
SI5345A-D06546-GM подходит для 7 применениеs: SyncE / IEEE 1588 Carrier-Grade Timing, 100G/200G/400G Ethernet PHY & Switches, Broadcast Video Reference Timing (SMPTE/PTP), OTN / Optical Transport Line Cards, Data-Center Top-of-Rack / Spine Switches, Industrial / Test & Measurement Instrumentation, Carrier Wireless Fronthaul / Backhaul Timing.
SyncE / IEEE 1588 Carrier-Grade Timing
The SI5345A-D06546-GM is well matched to SyncE (ITU-T G.8262) and IEEE 1588 packet-timing applications because its DSPLL-based jitter attenuator achieves sub-200 fs RMS typical jitter over 12 kHz-20 MHz, comfortably meeting G.8262 EEC options 1 and 2 mask requirements. The configurable loop bandwidth (0.1 Hz to 1 kHz) lets the same IC attenuate wander from packet-based PTP masters while still tracking GPS/GNSS references without an extra PLL stage. Each of its 10 outputs can be set to an independent PTP/SyncE frequency (e.g., 156.25 MHz, 161.1328 MHz, 125 MHz), removing the need for multiple external jitter cleaners in PTP grandmaster, boundary clock, and transparent clock cards. Up to 10 line cards can be clocked from one Si5345A per chassis, reducing BOM cost and oscillator count.
Рекомендуется
100G/200G/400G Ethernet PHY & Switches
In 100G/200G/400G Ethernet switches and OTN line cards, the SI5345A-D06546-GM drives one to ten 100 Gbps PAM4 SerDes reference clocks (typically 156.25 MHz, 161.1328 MHz, 312.5 MHz) while filtering recovered-clock jitter. MultiSynth fractional-N architecture delivers non-integer multiples of the reference with 0 ppm error, critical for OTU2/OTU4c mapping where every ppm becomes a wander budget hit. Programmable per-pin LVPECL, HCSL, CML or LVDS driver types connect directly to switch ASIC SerDes reference inputs without level translators. One Si5345A typically replaces three to five crystals and PLLs in a top-of-rack switch, freeing PCB area and reducing BOM cost.
Рекомендуется
Broadcast Video Reference Timing (SMPTE/PTP)
The SI5345A-D06546-GM is well suited to broadcast studio reference generators, PTP grandmasters, and UHD camera signal chains requiring SMPTE 2059-2/2110 timing. Its 10 independent outputs let the same device feed 27 MHz (SD), 74.25 MHz (3G-SDI), 148.5 MHz (UHD-SDI), 1.5 GHz (UHD-12G) reference clocks into downstream SDI encoders, FMC daughter cards, and PTP-aware cameras without external multipliers. The DSPLL bandwidth can be tuned to remove PTP packet-delay variation while remaining compliant with SMPTE 2059-2 PTP profiles. Hardware-level PTP timestamps benefit from the low-rms-jitter (<200 fs) reference, which directly improves timestamp accuracy and downstream audio/video lip-sync.
Рекомендуется
OTN / Optical Transport Line Cards
Optical transport network (OTN) line cards with 10G/100G/200G/400G coherent optics demand extremely low-jitter reference clocks because OTU4 FEC eyes are sensitive to instantaneous phase perturbations. The SI5345A-D06546-GM provides the wideband-tracking DSPLL required to maintain coherency across the tributary aggregate, with configurable bandwidth (Hz to kHz) matching the OTN OTU mask requirements. Each of the 10 outputs can be dedicated to a different optical module (multiple CFP2, QSFP-DD, OSFP cages), with on-chip level translation eliminating external LVPECL/HCSL buffers. Reducing discrete PLLs and crystals simplifies the line-card BOM and increases reliability in NEBS-compliant equipment.
Рекомендуется
Data-Center Top-of-Rack / Spine Switches
In hyperscale data-center switches, the SI5345A-D06546-GM consolidates the timing tree by replacing the four to six PLLs typically scattered across a switch board. The MultiSynth fractional-N architecture produces any-rate outputs from a single low-cost crystal, and the digitally programmable DSPLL cleans recovered packet/PTP jitter before it reaches switch ASIC SerDes. Up to ten independent differential pairs support redundant switch ASICs and management processors simultaneously. Power consumption is well below discrete multi-PLL solutions, which is meaningful for 48-port top-of-rack switches with dense front-panel I/O.
Рекомендуется
Industrial / Test & Measurement Instrumentation
Precision test-and-measurement instruments (spectrum analyzers, arbitrary waveform generators, real-time oscilloscopes) require deterministic low-jitter timing because jitter directly distorts high-resolution ADC sampling edges. The SI5345A-D06546-GM drives the ADC/DAC sample clocks (e.g., 245.76 MHz, 491.52 MHz, 983.04 MHz), reference lock for frequency counters, and PTP grandmaster for synchronized test racks. The 10 independent outputs allow one IC to feed multiple ADCs, DACs, and DAC clock domains in a single instrument without external fan-out stages. Industrial temperature grade and field-software-upgradeable frequency plans make the Si5345A attractive for calibrated test equipment.
Рекомендуется
Carrier Wireless Fronthaul / Backhaul Timing
In 5G/4G/LTE small-cell, fronthaul, and backhaul baseband units (BBU/RU), the SI5345A-D06546-GM drives the radios' air-interface clocks (e.g., 30.72 MHz LTE, 122.88 MHz 5G NR) while generating IEEE 1588 PTP and SyncE references for end-to-end phase coherence. The Si5345A's narrow loop bandwidth can reject backhaul packet jitter while still tracking a GPS-disciplined grandmaster, meeting the 5G tight phase/time synchronization requirements (3GPP TS 38.905). HCSL, LVPECL, LVDS, or CMOS output drivers cover radios directly without level translators, and the 10 outputs let one device serve a 4T4R radio plus a backhaul switch.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для SI5345A-D06546-GM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | SI5345A-D-GM | SI5345A-D04594-GM | SI5345A-D04594-GMR | SI5345A-D06546-GMR | SI5344B-D-GM | SI5341B-D13308-GM |
|---|---|---|---|---|---|---|---|
| Brand | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) | Silicon Labs (Skyworks) |
| Package | 64-pin QFN (10x10 mm) | 64-pin QFN (10x10 mm) - same | 64-pin QFN (10x10 mm) - same | 64-pin QFN (10x10 mm) - same | 64-pin QFN (10x10 mm) - same | 64-pin QFN (10x10 mm) - same | 64-pin QFN (10x10 mm) - same |
| Number of Outputs | 10 | 10 - same | 10 - same | 10 - same | 10 - same | 4 - fewer | 10 - same |
| Max Output Frequency | 1028 MHz | 1028 MHz - same | 1028 MHz - same | 1028 MHz - same | 1028 MHz - same | 1028 MHz - same (max per output) | 750 MHz - lower |
| Jitter Attenuator (DSPLL) | Yes (fractional-N DSPLL) | Yes - same | Yes - same | Yes - same | Yes - same | Yes - same | Yes - same |
| OTP Frequency Plan | Pre-loaded 06546 plan | Generic default OTP | Pre-loaded 04594 plan | Pre-loaded 04594 plan | Pre-loaded 06546 plan (same as target) | Generic default OTP | Pre-loaded 13308 plan |
| Packaging | Tray | Tray | Tray | Tape & Reel | Tape & Reel | Tray | Tray |
| Approx. Qty-1 Unit Price (USD) | 28.53 | ~28.50 | ~26.00 | ~26.50 | ~28.50 | ~20.00 | ~22.00 |
Ключевые отличия
- Single-chip 10-output any-frequency clock tree (против Discrete multi-PLL solution (e.g., 3x LMK04828 + crystals))
- Digitally programmable jitter-attenuation bandwidth (против Si5338A-B-GM (fixed-bandwidth loop))
- Same 64-pin QFN across Si5345/Si5344/Si5342 family (против Si5338/B series (different 32- or 40-pin QFNs))
Заметки по проектированию
Estimated: at a typical design with 9 outputs active at 156.25 MHz LVPECL (8 mA per output) and 1 active at 245.76 MHz LVDS, the SI5345A-D06546-GM draws approximately 0.8 W from the 1.8 V core supply. With theta_JA of approximately 28 C/W on a 4-layer FR4 board, junction temperature rises approximately 22 C above ambient (e.g., 65 C junction at 25 C ambient), well within the -40 C to +85 C operating range. For force-air-cooled chassis with 70 C inlet air, expose the QFN exposed pad to an 8x8 mm inner copper pad stitched with thermal vias for design margin.
Place the input crystal reference (XA/XB) traces as short, 100-ohm differential pairs within 5 mm of pins 3-4, and route them over a continuous reference ground plane with no splits beneath. The XO pin output trace should be no longer than ~10 mm. Each LVPECL/LVDS output pair should be routed as a 100-ohm differential with matched lengths within 150 mil (3.8 mm) to limit skew; place series-termination resistors (RC) within 200 mil of the driver pin. The ClockBuilder Pro schematic review guide recommends 5 to 6 decoupling caps: 0.1 uF + 10 uF + 4.7 uF near each VDD pin and at the exposed pad.
Common SI5345A layout and configuration pitfalls: (1) leaving the exposed thermal pad unconnected to ground (causes thermal shutdown or LOL under load); (2) configuring mismatched output driver types on differential pairs (LVDS_P vs. LVPECL_P mismatch causes asymmetric jitter); (3) failing to re-flash the OTP image with a custom plan and then trying to use the factory-default profile in a system that expects user frequencies; (4) failing to assert RST low then high on power-up so the device boots from the OTP plan; (5) using a 3.3 V supply while I2C pull-ups to 1.8 V - pull-ups MUST match VIO; consult the Si5345/44/42 Family Reference Manual Rev. D section 3 for power-up sequencing.
For signals going to a downstream ASIC, place the series-termination resistor within 200 mils of the driver pin to limit overshoot and ringing. For LVPECL AC-coupled operation, the receiver-side bias network is mandatory (usually 50k/86k to Vcc-2V or equivalent bias-tee). Per the Si5345/44/42 Family Reference Manual Rev. D, when targeting sub-200 fs jitter performance, use HCSL with 50-ohm single-ended termination for PCIE Gen3/4 compliance. Keep the reference clock differential pair matched within 50 mils; mismatches couple into the DSPLL loop and degrade jitter-attenuator performance.
Информация о соответствии
Listed as RoHS compliant on distributor pages (Heisener, DigiKey, Mouser). No AEC-Q100 qualification (industrial/communications timing IC, not automotive). Conflict Minerals / CMRT and DRC Conflict Mineral Reporting Template compliant per Silicon Labs policy.
